Owners Manual - Audiant VP3 (v1.0a)
Contents
1. Please contact your dealer or a competent electrician if you are in any doubt Refer to the rear of the product for fuse and mains voltage information indicates compliance and that these products must be recycled or processed as This product is designed to comply with international directives on the Restriction of Hazardous Substances RoHS in electronic equipment The wheelie bin logo un according to these directives General Safety Instructions All safety and operation instructions should be read carefully before the Audiant VP3 Vinyl Preamplifier is operated Keep the Owners Manual in a safe place for future reference Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use the device near water for example near a bathtub kitchen sink in a wet basement near a swimming pool etc Clean only with a dry cloth Mounting to a wall or ceiling should be via a heavy duty bracket or shelf designed for audio equipment use The device should be situated away from heat sources such as radiators stoves or other appliances that produce excessive amounts of heat DO NOT place the device directly onto carpeted surfaces Avoid exposing the device to extremely high or low temperatures The device should be connected to a mains power supply only of the type described in the operating instructions and or as marked on the rear of the unit DO NOT defeat the2. Audiant VP3 Vinyl Preamplifier Owners Manual a e gt Audiant VP3 Vinyl Preamplifier Important Safety Instructions Explanation of symbols used in this manual or on the rear of the device This symbol is intended to alert the user to the presence of uninsulated dangerous voltages within the enclosure of sufficient magnitude to cause electric shock This symbol is intended to alert the user to the presence of important operation maintenance and servicing information in the instruction and service manuals Caution To reduce the risk of electric shock do not remove the cover No user serviceable parts inside Refer servicing to qualified service personnel Replace the mains fuse in the plug with one of the same type and rating Disconnect supply cord before changing fuse Warning To reduce the risk of fire or electric shock do not expose this device to rain or moisture Shock hazard do not open Mains Plugs This device is supplied with a non rewireable mains plug for the intended country Replacement mains leads can be obtained from your Perreaux dealer Should you need to change the plug please dispose of it carefully Aplug with bared conductors is dangerous if engaged in a live socket The Brown wire must be connected to the Live Line supply pin The Blue wire must be connected to the Neutral supply pin The Green Yellow wire must be connected to the Earth Ground supply pin
3. We make no excuses for producing some of the most distinctive high end audio products on the planet We let form and function blend together in perfect harmony This surely is the essence of true minimalist utilisation Minimalism in a wider context John Pawson writes Clearly simplicity has dimensions to it that go beyond the purely aesthetic it can be seen as the reflection of some innate inner quality or the pursuit of philosophical or literary insight into the nature of harmony reason and truth Features at a Glance Slim and stylish The VP3 features an extruded full width monocoque aluminium cover front panel assembly The chassis is then carefully sandblasted and clear anodised The front panel consists of a beautiful black perspex touch panel for minimalist selection of all functions The VP3 is slim and stylish and will perfectly compliment any listening environment Highly flexible The VP3 will fully cater for all high low output moving coil and moving magnet cartridge types Fully customisable The 36 rear mounted user accessible dip switches provide maximum flexibility and versatility In years to come you may wish change your cartridge according to your tastes however there is no need to change your VP3 as it can easily be adjusted to suit In the rare event that you can t find the correct dip switch settings the VP3 can also be internally customised to suit your exact requirements Two turntables can b
4. inessentials Perreaux has historically embraced the minimalist ethic from an audio design perspective only The concept of less equating to more has been at the heart of all Perreaux audio designs for more than 40 years Minimalist electronics We wish to maximise the quality of your listening pleasure by keeping the componentry and signal path as uncluttered short and clean possible All components in the signal path even those of the highest quality have an effect on the signal thereby altering the quality of the reproduction in some way Our aim is to recreate in its entirety the original performance by not adding or subtracting anything irrespective of the source Minimalist user Interface We carefully study the user interface and par down the number of buttons and associated clutter leaving just the essential and no more How tempting it has been over the years to loose sight of our core values as technology or trends have made it possible That is one of the reasons why our older products still have such a high resale value today The user interface has and always will remain simple free from adornments clean and uncluttered Minimalist aesthetics Our products appeal to those who seek the ultimate in audio exclusivity namely the perfect blend of form and function Form and function are both tough masters That is why our amplifier heat sinks are not hidden but instead feature prominently in all our designs
5. a flat surface for air circulation to allow heat to dissipate Do not place directly onto a carpeted surface as it will reduce air circulation and the heat will not dissipate as intended It the device is used in a cabinet air must be able to flow through An enclosed cabinet will severely restrict heat dissipation Ensure that nothing is placed above or below the unit that might block or restrict the vents Other Devices Ideally your Audiant VP3 Vinyl preamplifier should not be located directly above or adjacent to other heat producing products such as radiators other power amplifiers etc If multiple amplifiers are being used and space is restricted placing them side by side is preferable to stacking It is advisable to position your Audiant VP3 Vinyl Preamplifier close to your turntable and away and if possible connected to a power socket on a different circuit from powerful electrical or electronic products such as TV sets computers cookers fridges etc This will prevent the possibility of the strong electrical and electromagnetic emissions or interference given off by such devices adversely affecting the performance of your preamplifier Ape Connecting Rear Panel Important Before making any connections switch off the mains power to all components in your system 1 Power On Off The Power switch turns power to the unit on and off 2 Ma
6. below document the loading for each input 12 It is recommended that one resistive load and one capacitive load switch are operated at any given time when required However it is possible to use more than one switch to produce a cumulative value when doing this the values in the tables below must be added electrically in parallel to give the overall load value In the rare occurrence that your cartridge load specifications do not fall within the factory load settings there is also the ability of adding your own custom loading components This customisation will need to be carried out by a qualified service agent please contact your dealer for further information on this functionality MM Loading Dip Switch ee 1 SS 47kQ 10kQ 22pF 47pF 100pF 220pF 470pF MC Loading Dip Switch Gain The gain characteristic of the Audiant VP3 Vinyl Preamplifier can be configured to suit the output voltage of the cartridge you are using A switch in the UP position is ON and a switch in the DOWN position is off When discussing the gain of a vinyl preamplifier the words gain and sensitivity are often both used The gain figure tells you how many dB of amplification is added to the signal while the sensitivity figure tells you the level of input required to achieve the rated output of the preamplifier It is more common to use the sensitivity value when deciding the correct gain setting to use as the rated output voltage of your cartridge can be
7. matched to this value to get the most out of your VP3 Vinyl Preamplifier The tables below document the gain settings for each input and list the corresponding sensitivity value Consult your cartridge documentation for its rated output voltage and set the gain configuration where the Sensitivity of the Audiant VP3 Vinyl Preamplifier is within 50 of this output voltage in the corresponding table Note If more than one setting falls within 50 of your cartridge output voltage the lower sensitivity configuration will result in greater dynamic range the higher will be less susceptible to clipping MM Gain Dip Switch 36dB 40dB 44dB 48dB MC Gain Dip Switch Gain 56dB 60dB 64dB 68dB RIAA Equalisation Two settings are available for RIAA Equalisation of the Audiant VP3 Vinyl Preamplifier to suit your recordings or personal preference Normal RIAA and IEC RIAA These two settings are selectable using switch 4 of the gain dip switch on each input With the switch in the DOWN position the Normal equalisation is selected in the UP position the IEC equalisation is selected Normal RIAA Equalisation Curve 20 10 0 a E 10 20 30 4 10 20 40 100 200 400 1k 2k 4k 10k 20k 40k Frequency Hertz IEC RIAA Equalisation Curve 20 10 0 a g 10 20 30 4 10 20 40 100 200 400 1k 2k 4k 10k 20k 40k Frequency Hertz 14 Configuration
8. stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of the publisher The content of this manual is furnished for information use only is subject to change without notice and should not be construed as a commitment by Perreaux Industries Ltd Perreaux Industries Ltd assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual All trademarks and registered trademarks are the property of their respective owners Perreaux the Perreaux logo and Audiant are trademarks of Perreaux Industries Ltd All rights reserved Printed in New Zealand Ape Introduction Thank you for choosing this Audiant VP3 Vinyl Preamplifier We sincerely hope it provides you with many years of music listening pleasure The Audiant VP3 is a highly flexible customisable vinyl preamplifier capable of connecting both Moving Magnet and Moving Coil cartridges to your audio system providing low distortion high dynamic range and a sound which is open detailed and transparent The VP3 includes separate low noise input stages for Moving Magnet and Moving Coil cartridges with dip switches for both resistive and capacitive loading on each input allowing for a clean direct customisable signal path from the cartridge output The separate direct connections and switches ensure minimal noise and maximum channel separation
9. 47pF selectable 22dB 1 mono 3 5mm jack OVDC 3 12VDC 1 Unbalanced RCA 1 Balanced XLR 300 1002 0 75Vrms 10 3Vrms 14 5Vp p 0 002 1kHz rated output lt 0 05 rated output 0 5dB 50Hz to 20kHz 87dB 0 5A slow blow 431mm 17 0 277mm 12 2 67mm 2 6 7 5kg 16 51b Physical Dimensions PERREAUX Af 67mm y 2 67 W J 431mm 17 M 17 N 277mm 12 2 J 18 Installation Notes Please record the serial number of your Audiant VP3 Vinyl Preamplifier for future reference Serial Number Contact Details Perreaux Industries Ltd PO Box 305 Mosgiel Dunedin 9053 New Zealand T 64 3 489 2975 F 64 3 489 2976 E nz info perreaux com W www perreaux com Ape Right put output N METRE lt e as Loading lt Loading o Gain MM Gain MC A PERREAUX Made with Pride in New Zealand Audiant VP3 Vinyl Preamplifier Www perreaux com Perreaux Industries Ltd PO Box 305 T 64 3 489 2975 Mosgiel F 64 3 489 2976 Dunedin 9053 E nz info perreaux com New Zealand W www perreaux com
10. Example The following is a working example of the popular Thorens TD295 MK iV turntable equipped with an Ortofon Super OM 40 Moving Magnet cartridge being set up to play using the Audiant VP3 Vinyl Preamplifier This example can be used as a guide to help you set up your system Thorens TD 295 MK IV Specifications Tonearm and lead capacitance 160pF Ortofon Super OM 40 Moving Magnet Cartridge Specifications Recommended load resistance 47K ohms Recommended load capacitance 200pF 400pF Rated output voltage required to adjust the gain dip switch setting 4 0mV Configuring your Audiant VP3 to suit the above Output of the turntable connected to the MM input of the Audiant VP3 MM dip switch Loading Dip switches 1 amp 2 select Resistance values If dip switches 1 amp 2 are both down by default the resistance will be 47K ohms which is the correct as per the Ortofon OM 40 specifications above MM dip switch Capacitance Dip switches 3 7 select capacitance values By selecting dip switch 5 upwards this provides 100pF turntable capacitance of 160pF total capacitance of 260pF which falls within the recommended range of 200pf 400pF MM dip switch Gain calculation Dip switches 1 3 are used to set the gain value The Ortofon Super OM 40 has a rated output voltage of 4 0mV Set the gain dip switches to be within or 50 of the output voltage value of the cartridge Therefore 4 0mV or 50 is 2 0mV to 6 0mV Using this info
11. choice in your own listening area before you finally make your purchase When deciding on your system you will need to differentiate between sales gimmicks and cosmetic wizardry as against practical features and facilities Recognise the Christmas Tree Syndrome namely the more flashing lights and switches the better it must be Bear in mind that you are paying for these and because of the necessity of careful pricing compromises may have been made in the internal component quality vital for accurate sound reproduction Each component through which the audio signal must pass will add its own character to the music you hear hence the expression colouration Perreaux products are carefully designed to minimise componentry within the audio signal path All componentry used is of highest quality and only included when absolute necessity is established no component is there for a free ride or to correct for deficiencies elsewhere in the circuitry With Perreaux emphasis is placed on maximum sound quality component and unit reliability and long life Minimalist Design Minimalist design Leading British architect John Pawson writes The Minimum can be defined as the perfection that an object achieves when it is no longer possible to improve it by subtraction This is the quality that an object has when every component every detail and every junction has been reduced or condensed to the essentials It is the result of the omission of the
12. ction 11 Customisation Important Before making any changes to the dip switch settings ensure that the unit is in Standby or switch off the mains power The Audiant VP3 gives you complete flexibility in customising the Vinyl preamplifier to suit your cartridge system and personal audio preferences This customisation is achieved with seven different loading switches three gain switches mono selection and the ability to switch between a normal or IEC RIAA equalisation curve on each input Customisation is achieved using the six separate sets of dip switches on the rear of the unit and the mono selection button on the front panel Separate switches are used to allow for maximum isolation between each channel and input It is recommended that you make adjustments to the dip switch settings using a small flat tip screwdriver or other similar pointed object Loading Loading settings should be configured to directly correspond to the cartridge manufacturers recommended loading figure If you don t know the recommended loading of your cartridge please contact the cartridge manufacturer or your dealer for this information before proceeding There are two sets of loading dip switches for each of the two inputs one for the left channel and the other for the right channel The left and right switches should be set to be a mirror of the other for both inputs A switch in the UP position is ON and a switch in the DOWN position is off The tables
13. d be connected to the right channel of the corresponding input of the Audiant VP3 Vinyl Preamplifier Note High output MC cartridges can be connected to the MM input if the MC input results in excessively high sound output 8 Balanced Outputs The balanced XLR outputs provide a balanced audio signal for connection directly to a preamplifier or integrated amplifier The pin assignments of the balanced XLR output connectors are Pin 1 Shield Pin 2 ve signal hot Pin 3 ve signal cold Please refer to the owner s manual of your amplifier to verify that the pin assignments of the input connectors correspond as above If this is not the case wire the cables so that the appropriate Audiant VP3 Vinyl Preamplifier output pin connects to the equivalent preamplifier input pin Note The balanced outputs employ entirely separate buffer stages to the unbalanced outputs allowing both outputs to be used simultaneously without degrading the performance of each other 9 Unbalanced Outputs The unbalanced RCA outputs provide a single ended audio signal for connection directly to a preamplifier or integrated amplifier Note The unbalanced outputs employ entirely separate buffer stages to the balanced outputs allowing both outputs to be used simultaneously without degrading the performance of each other 10 Gain RIAA Adjustment Switches The gain RIAA adjustment switches provide further customisation to each input to allow greater flexibilit
14. e independently set up and simultaneously run The VP3 can simultaneously cater for two turntables One turntable input can be set to use moving magnet or high output moving coil cartridge and the other turntable input can be set up for a low output moving coil Possible options are 1x Moving magnet turntable and 1 x low output moving coil turntable 1x High output moving coil turntable and 1 x low output moving coil turntable Touch panel selectable The VP3 features capacitive touch panel selection of all front panel icons The user can turn the unit on or off select between moving magnet and moving coil inputs and turn the mono output on or off Separate inputs The VP3 features separate low noise input stages for moving magnet and moving coil cartridges ensuring minimal noise and maximum channel separation Normal RIAA or IEC RIAA equalisation profiles Using the rear mounted dip switches the user can select between normal RIAA and IEC RIAA equalisation profiles Highly accurate and low distortion Featuring a diminutive total harmonic distortion figure of only 0 002 at 1KHZ rated output the VP3 is highly accurate and will faithfully reproduce your favorite recordings to be as perfect a recreation of the original as possible High dynamic range The VP3 features an exceptional dynamic range Balanced and unbalanced outputs The VP3 features balanced and unbalanced outputs By employing entirely separate buffer stages it is
15. epts voltages of OV DC up to 12V DC A trigger voltage between 3V and 12V DC will bring the amplifier out of standby and it will enter standby when the trigger voltage is OV DC The trigger input plug must meet the specifications shown below re TP Sleeve GND H gt i 5 RS232 Port The RS232 port allows external serial control of the Audiant VP3 Vinyl Preamplifier for custom install use A full command set is available on the Perreaux website This port can also be used by authorised Perreaux service personnel for software updates 10 6 Loading Switches The loading switches provide customisation of each input to correspond with the cartridge manufactur ers recommended loading figure Four seperate loading switches are required to allow for maximum isolation between the inputs and channels Each loading switch should be set for the corresponding input with the left and right channels to be a mirror of each other For more information on these switches please refer to the Customisation section page 11 Note Always ensure that the system is powered down or in standby before making any adjustments to the load switches 7 Phono Inputs The Audiant VP3 Vinyl preamplifier has two separate input sections specifically designed to cater for moving magnet MM and moving coil MC cartridges Each set of phono inputs accept standard unbalanced RCA analogue outputs from the corresponding cartridge type The output of a mono cartridge shoul
16. ing post Ensure that your turntable is located close to your Vinyl Preamplifier and away from possible sources of EMI and or RF interference for example computers televisions etc 16 Technical Specifications All specifications are accurate at the time of printing Perreaux Industries Ltd reserves the right to adjust specifications without notice All specifications measured at 230V after a 10 minute warm up period using an Audio Precision ATS 2 Audio Analyser Measurements taken at 65kHz bandwidth unless specified otherwise Measurements taken with lowest gain setting at rated output where appropriate Inputs Audio Inputs Input Sensitivity MM input MC input Gain MM input MC input Input Impedance MM input MC input Input Capacitance MM input MC input Input Overload Margin Trigger Input OFF voltage ON voltage Outputs Audio Outputs Output Impedance Balanced Unbalanced Rated Output Maximum Output Preamplifier Total Harmonic Distortion THD N Typically 20Hz to 20kHz RIAA Accuracy Signal to Noise Ratio un weighted General Mains Fuse Rating Dimensions Width Depth Height Weight MW 2 Unbalanced RCA selectable 3 0mV to 11 9mV selectable 0 3mV to 1 2mV selectable 36dB to 48dB selectable 56dB to 68dB selectable 1kQ to 47kQ selectable 10Q to 47kQ selectable 22pF to 470pF selectable
17. ins Power Socket The Mains Power Socket is used with the removable mains power cord to supply your Audiant VP3 Vinyl Preamplifier with power Before connecting your Audiant VP3 Vinyl Preamplifier to the mains power please check the voltage label on the rear panel to ensure that your preamplifier conforms to the power supply in your area Never attempt to connect the unit to an incorrect voltage severe damage may result Note The unit must always be earthed when connected to mains power Use the earthed moulded mains lead supplied Never use an unearthed mains plug socket or adaptor with this unit The mains lead supplied may be fitted with a fused plug depending on local regulations If this is the case always replace this fuse with another of the same type and rating 3 Mains Fuse The mains fuse is user serviceable and should always be replaced with the same type and rating see Technical Specifications section page 16 Ensure your Audiant VP3 Vinyl Preamplifier is disconnected from the mains power before attempting to change the fuse Note Fuses do not usually blow without a reason Any doubts about fuse failure should be conveyed directly to your Perreaux dealer 4 Trigger Input The trigger input allows the Audiant VP3 Vinyl Preamplifier to be brought in and out of standby by a remotely connected device for example another audio component or a home automation system The trigger input uses a mono 3 5mm plug and acc
18. nto the wall socket and is switched on Check the mains fuse of the unit Check fuse in the mains plug or adaptor There is no sound Check that the input and output interconnects are properly connected to the respective sockets Confirm that the cartridge is correctly connected and fitted to the tone arm 15 Check that the turntable is turned on and that the tone arm is lowered onto the record Check that your preamplifier and or amplifier are turned on and the correct input is selected Check that the volume on your preamplifier is set to a suitable level and not muted Check that your speakers are firmly connected to your amplifier There is no sound on one channel Check interconnects Check balance setting of your preamplifier and or amplifier is set to the middle There is a crackling noise coming from the speakers Check that the gain setting is configured correctly for your cartridge and not too high Try a lower gain setting to ensure output is not clipping Check that the needle and record are free from dust and debris The output from the speakers is too quiet Check that the gain setting is configured correctly for your cartridge and not too low Try a higher gain setting until a suitable volume level is achieved Check the cartridge loading settings are set correctly There is a loud buzz or hum Ensure no interconnects are loose or defective Ensure the earth terminal from your turntable is solidly connected to the earth bind
19. perfectly acceptable to use both outputs simultaneously without interference or degradation in signal performance Ape Highest quality internal power supply The VP3 features a fully shielded toroidal transformer with shunt voltage regulation and filtering resulting in an ultra low noise power supply providing high levels of transparency detail and dynamics Fully mirrored internal layout The internal layout has been laid out in full mirror fashion to ensure maximum channel separation Trigger input The VP3 can be remotely turned on and off as part of your system using the rear mounted trigger input Mono The VP3 also caters for mono recordings Installation Unpacking The Audiant VP3 Vinyl Preamplifier is supplied with the following accessories Mains lead This manual 3 5mm mono remote trigger lead We recommend you retain the packaging for reuse in case you need to transport the unit at a later date Placement Your Audiant VP3 Vinyl Preamplifier should generally be placed close to your preamplifier keeping interconnect cabling short Although when using balanced interconnects the amplifier may be placed further away from the preamplifier without degrading the sound Ventilation Reguirements Your Audiant VP3 Vinyl Preamplifier should be placed in a position that does not restrict the airflow around it Allow at least 80mm 3 inches above and to each side of the unit and mount your Audiant VP3 Vinyl Preamplifier on
20. reate the original performance in its entirety via the recorded medium To help you get to know what various instruments really do sound like listen to live concerts of musical performances that you prefer Select a few recordings of similar performances for comparison Your Perreaux equipment will and the rest of your system should provide a precise duplication in your listening area of the total musical performance including the ambience of the venue in which the recording was made Read magazines Read hi fi and audiovisual magazines particularly the equipment reviews and letters to the editor sections Use these as a general guide only and try to read between the lines Remember no one specifically sets out to downgrade a particular piece of equipment so what is not included in the review is often as important as the actual printed content Choose Your Hi Fi dealer carefully Choose your hi fi dealer carefully they are your professional guide Preferably they should be knowledgeable about music and recording techniques as well as the equipment itself They should be able to provide a total service including installation system tuning advice problem solving and after sales service Frequent your dealer and listen to a variety of equipment using recordings which are familiar to you Ask questions and listen to advice but remember to trust your own ears to tell you what sounds right for you If possible listen to your equipment
21. rmation you select dip switches 1 and 2 to on which will provide a corresponding value of 4 7mV sensitivity which equates to 44dB of gain Note Selecting dip switches 1 2 and 3 would also be acceptable it would be more susceptible to clipping but give you the advantage of increased dynamic range Correct dip switch selection for the example above MM loading dip switch switch 5 up and all others down Gain dip switches 1 2 up alternately 1 2 and 3 up MM Gain dip switch 4 Used to set either the Normal RIAA equalisation curve down or the IEC RIAA equalisation curve up PERREAUX Lu oe ad Audent VES Vinyl Preamplifier T T L Care and Maintenance Notes Always switch the unit off and remove the power cord from the rear of the unit before attempting to clean your Audiant VP3 Vinyl Preamplifier in the manner described below Never apply liquid directly to the unit Never use abrasives Never rub in a circular motion Front Panel and Cover The front panel and cover feature a durable high quality anodised finish To remove finger marks and dirt simply rub the surface with a soft cloth If the dirt is not removed use a small quantity of isopropyl alcohol on a clean cloth and rework the effected area Troubleshooting There is no power Ensure the AC power cord is connected securely Ensure the mains plug is fully inserted i
22. safety earth of the grounding type mains plug severe injury or death may result If the provided plug does not fit into your outlet contact your dealer or consult an electrician The power cord should be routed so that it is not likely to be walked on or pinched by items placed on or against it Unplug the device during lightning storms or when unused for long periods of time DO NOT let objects or liquids fall into the device expose the device to dripping or splashing or place a vessel containing liquid on top of the device Keep this device out of reach of children DO NOT operate the device with the cover removed DO NOT bypass any fuse replace only with the value and type specified DO NOT attempt to repair the device In the event of a problem please contact your Perreaux dealer DO NOT operate this product in an explosive atmosphere Table of Contents INTRODUCTION 4 THE DECISION MAKING PROCESS 5 MINIMALIST DESIGN 6 FEATURES AT A GLANCE 7 INSTALLATION 8 CONNECTING 9 Rear Panel 9 OPERATION 11 Front Panel 11 CUSTOMISATION 11 CONFIGURATION EXAMPLE 14 CARE AND MAINTENANCE 15 TROUBLESHOOTING 15 TECHNICAL SPECIFICATIONS 16 PHYSICAL DIMENSIONS 17 CONTACT 18 Copyright and Acknowledgments Audiant VP3 Manual Version 1 0 Copyright 2015 Perreaux Industries Ltd Perreaux Industries Ltd Gladstone Road Mosgiel Dunedin 9024 New Zealand All rights reserved No part of this publication may be reproduced
23. with the added ability of connecting two cartridges simultaneously and conveniently selecting between the two from the front panel Four different gain settings the ability to switch between the normal RIAA and IEC RIAA equalisation curves and the selectable Mono input ensure the highly flexible VP3 is compatible with any cartridge and audio system through the high rated balanced XLR and unbalanced output connections The highest quality internal power supply features a custom designed fully shielded toroidal transformer with shunt voltage regulation and filtering ensuring a low noise supply providing high levels of transparency detail and dynamics The internal layout ensures that the power supply is separated from the preamplifier stage to reduce noise while the mirrored layout of the preamplifier design about the output ensures maximum channel separation Whether as part of a complete Audiant system or as the vinyl preamplifier in your existing system the VP3 will reconnect you with your MUSIC Thank you for taking the time to read this manual we do recommend you keep it for future reference MU Ronn Martin van Rooyen Perreaux Managing Director and the Perreaux design team The Decision Making Process In this section our objective is to help you extract the most out of your investment in your audio system May we take a moment of your time with the following suggestions The aim of high fidelity audio is to attempt to rec
24. y in matching the output of the Audiant VP3 Vinyl Preamplifier to your system For more information on these switches please refer to the Customisation section page 11 11 Phono Earth Terminal The phono earth terminal connects to the earth lead from the tonearm cable of your turntable if required If your turntable does not have a separate earth lead it may be advisable to run a wire from a grounded screw on the turntable to this terminal Turntables are very sensitive to hum and grounding the table or cartridge to the Audiant VP3 Vinyl Preamplifier can help reduce hum Ape Operation Front Panel PERREAUX p N 1 Standby Button The Standby Button switches the unit between Standby mode indicated by dim standby LED and On indicated by bright standby LED The unit should be left in Standby mode when not in use 2 Source Buttons The Source Buttons allow you to select the source component that you wish to listen to 3 Mono Selection Button The Mono Selection Button switches between mono indicated by bright mono LED and stereo indicated by dim mono LED output to allow playback of mono LPs A press of the button will toggle the mono selection on and off with the current selection conveniently stored for each input The output of the Mono cartridge should be connected to the right channel of your Audiant VP3 Vinyl Preamplifier For more information on the mono selection button please refer to the Customisation se
Download Pdf Manuals
Related Search