INSTALLATION MANUAL FS-521 Finisher
Contents
1. Finisher key to display the serial number setting screen Select the installa tion order key 7 Enter the serial number of the FS 521 and touch the OK key Use Shift to switch between upper case letters and lower case letters Touch the Return key then touch the Close key E 24 VIII Importing FS Adjustment Data Import the factory adjustment data of the FS 521 to the machine memory If a FS 521 and other optional units are connected they can recover the standard data at the same time COLOR MFP 65ppm series MFP 120ppm 105ppm 2 series rr the Finisher Adjustment key Completed in recalling standard data appears on the screen MFP120ppm 105ppm 2 series only C8000 C7000 C 7000P C 6000 C 70hc J 1 On the Service mode menu screen touch the Finisher Adjustment key Touch the Recall Standard Data key 2 3 Touch the Factory Initial Data key then touch the Yes key ie the Return key then touch the Close key IX Confirmation of Paper Output Output paper in binding mode If staples are skewed from the center or paper edges are not even adjust the settings See the Service Manual for adjustment method X Adjustment Data Backup If the FS 521 adjustment data is changed back up the machine finisher data to the FS 521 memory If a FS 521 and other optional units are connected the data will be back2. Machine installation plate R 15AQIXE052SA 11 Remove the lock shaft of the conveyance unit 1 black screw Note When removing conveyance unit being to use the lock shaft keep M 12 Pull out the conveyance unit secure it with screws TP screw black M3x8 2pcs included with the RU and push it back dip SEN M3x8 A i achine side 15AQIXE054SA 13 Loosen two screws and remove the connector cover on the back side of the RU conveyance segment 15AQIXE055SA 14 Connect two connector jacks of the power sup ply unit to the connector plugs of the conveyance segment and secure the wire bundle with two clamps as shown in the figure a 15AQIXE056SA 15 Secure the bundled connectors of the power sup ply unit with the clamp on the connector cover 15AQIXE057SA 16 Install the connector cover on the RU convey ance segment 2 screws Note Put the wire bundled into the RU machine so that it will not get hooked when the conveyance segment is pulled out Connector cover cae OAQIXEO58SA E 6 17 Install the rear cover included with the RU Truss screw black M4x6 2 pcs included with the RU Rear cover rN Truss screws black M4x6 15AEIXE044SB 18 Install the front cover included with the RU 1 Temporarily place two screws in the front of the power supply unit TP screw M4x6 2 pcos included with the RU l l I
3. 9 Install the FS 521 to the machine 1 Align the top and bottom holes of the FS 521 to the Installation plate 1 pins and lock them by sliding the FS 521 to the back ae ng if 15AEIXE014CA 2 Connect 3 FS 521 connector plugs to the con nector jacks of the main body on the paper exit Side 1 small 2 pin connector is not used Holes Installation plate 1 N M Not used 15AEIXC010SB 2 pin connector Not used AOGYIXC004CA E 9 3 Install the Connector cover TP screw black M3x4 2 pcs Connector cover TP screws black M3x4 Ne O L A e aR a aia a Lt AOGYIXCO05CA 4 Secure the upper part of the FS 521 to the main body with a screw TP screw M4x10 1 pc i Ar m s p rs 5 my ss 5 Install the Installation plate 4 to secure the lower part of the FS 521 to the main body TP screw M4x10 1 pc 15AEIXE014SA TP screw M4x10 15AEIXE015SA 10 Perform the operations described in VI Com mon operations after installing FS 521 page 23 2 Install the Installation plate 1 Installation procedure for FS 521 RU 506 MFP 120ppm 105ppm 2 series For the installation procedure for the RU 506 see the RU 506 installation manual 1 Turn OFF the machine s Sub and Main power switches and unplug the power cord 2 places the Installation plate 2 and the Installation plate 3 on the left side of the RU
4. Plug in the power cord COLOR MFP 65ppm series only Connect the power cord to the RU 504 and plug it into the outlet included in the machine package RU 504 FD 503 gt Power cord 15AEIXE064SB 6 Perform the operations described in VI Com mon operations after installing FS 521 page 23 E 20 Installation procedure for FS 521 SD 506 FD 503 RU 504 COLOR MFP 65ppm series FS 521 SD 506 FD 503 RU 506 MFP 120ppm 105ppm 2 series FS 521 SD 506 FD 503 RU 508 EF 101 COLOR MFP 80ppm series FS 521 SD 506 FD 503 RU 509 C7000 C 7000P C 6000 C 70hc For the installation procedure for the RU 504 506 508 509 see the RU 504 506 508 509 installation manual 1 Turn OFF the machine s Sub and Main power switches and unplug the power cord 2 Install the Installation plate 1 2 places the Installation plate 2 and the Installation plate 3 on the left side of the SD 506 as below TP screw M4x6 each 2 pcsx4 places Note For the Installation plate 2 and the Installation plate 3 use the screw holes with the engraved marking FS503 Installation plate 2 AATA e Engraved marking FS503 Engraved marking FS503 anununnnun Installation plate 1 15AEIXE017CA 3 Remove the connector cover on the left side of the SD 506 1 screw Connector cover 15AEIXE033SA E 21 4 Install the FS 521 to the SD 506 1 Connect the four FS 521 conne
5. i TP screws M4x6 temporarily secured o i 15AQIXE001CA 2 Align the bottom holes of the front cover with the pins of the power supply unit and use the temporarily placed screws to secure it 15AQIXE061SA Note lf the front cover does not close because it touches the machine or optional unit adjust the horizontal position or angle of the front cover If the actuator does not turn the interlock switch ON adjust the position of the actuator adjustment plate as well Loosen the screw to adjust the angle Loosen the screw to adjust the horizontal position 15AQIXFO62SA Actuator adjustment plate gt Loosen the screws to adjust the Z horizontal sa position 19 Plug in the power cord Connect the power cord to the RU 504 and plug it into the outlet included in the machine pack age RU 504 15AEIXE045SB E 7 20 Install the Connector cover TP screw black M3x4 2 pcs TP screws black M3x4 15AEIXC029SC 21 Perform the operations described in VI Com mon operations after installing FS 521 page 23 installati oced refor 4 Remove the CN 19 connector from the control Pa ranaell PrO EUNIS 10 board as shown in the figure below Remove the short connector from the clamp FS 521 MFP 105ppm 2 5 1 Turn OFF the machine s Sub and Main power switches and unplug the power cord 2 Install the Installation plate 1 2 places the Installation pl
6. 4x6 AOGYIXC006CB TP screw M4x10 3 Install FS 521 to RU 509 1 Connect the four FS 521 connector plugs to the connector jacks of the RU 509 Installation plate 4 lt AOGYIXC011CA 4 Perform the operations described in VI Com mon operations after installing FS 521 page 23 E 13 2 Align the top and bottom holes of the FS 521 to the Installation plate 1 pins and lock them by sliding the FS 521 to the back Note If the vertical opening between the FS 521 and the RU 509 is not even and their heights are different adjust the height of the four casters of the FS 521 to make the opening even Every caster has ratchet mechanism It goes up with reciprocating the driver into the whole 1 and it goes down with reciprocating the driver into the whole 2 Be sure not to go it up too much otherwise the bolt would come off max 5mm Be sure the caster is contacting installation surface otherwise the ratchet will not work 15AEIXE014CA 3 Install the Connector cover TP screw black M3x4 2 pcs TP screws black M3x4 15AEIXCO029SC 4 Secure the upper part of the FS 521 to the RU 509 with a screw TP screw M4x10 1 pc IODS TP screw M4x10 h wee NS P3 1SAEDKEOIOCA 5 Install the Installation plate 4 to secure the lower part of the FS 521 to the RU 509 TP screw M4x10 1 pc TP screw M4x10 ADS Installation plate 4 vf N A
7. 506 as below TP screw M4x6 each 2 pcsx4 places Note For the Installation plate 2 and the Installation plate 3 use the screw holes with the engraved marking FS503 Installation plate 3 7 ww e me a Z FS503 o Ee 7 ta FS503 7 7 fs or _ TP screws M4x6 AOGYIXCO06CA TP screws M4x6 3 Install FS 521 to RU 506 1 Connect the four FS 521 connector plugs to the connector jacks of the RU 506 E 10 2 Align the top and bottom holes of the FS 521 3 Install the Connector cover to the Installation plate 1 pins and lock them TP screw black M3x4 2 pcs by sliding the FS 521 to the back TP screws black M3x4 Installation plate 1 15AEIXC029SC 4 Secure the upper part of the FS 521 to the RU 506 with a screw TP screw M4x10 1 pc a a AOGY IXCO08CA Note If the vertical opening between the FS 521 and the RU 506 is not even and their heights are different adjust the height of the four casters of the FS 521 to make the opening even Every caster has ratchet mechanism ANE yo TSAEIKEOIOCA It goes up with reciprocating the driver into the 5 Install the Installation plate 4 to secure the whole 1 and it goes down with reciprocating the lower part of the FS 521 to the RU 506 TP driver into the whole 2 Be sure not to go it up too much otherwise the bolt would come off max 5mm Be sure the caster is contacting installation su
8. F S 52 1 Finisher INSTALLATION MANUAL Applied Machine C6501 C6501P C65hc C8000 C 7000 C 7000P C6000 C70hc 1200 1200P 1051 COLOR MFP 65ppm COLOR MFP 80 71ppm 71ppm 70ppm 70ppm 60ppm 60ppm MFP 120ppm 105ppm 2 Product Code AQU0 A0U2 A0Y8 A1 RF A1DU A204 A1 DV A205 A0G6 A0GA A0G9 l Contents COLOR MFP 65ppm series C 7000 C 7000P C 6000 C 70hc C6501 C 6501PC 65hc e FS 521 RU 509 C7000 C7000P C6000 pages 13 to 14 Pope ee aoe FS 521 PB 503 RU 509 C7000 C7000P nnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn C6000 C70hc pages 15 to 16 i P o vee ene il a FS 521 LS 505 RU 509 C7000 C7000P Pe ee C6000 C70hc pages 17 to 18 are alas TOO a ak 7 FS 521 FD 503 RU 509 C7000 C7000P Pe ee ee C6000 C70hc pages 19 to 20 ane OPO eeu oem oun street FS 521 SD 506 FD 503 RU 509 C7000 Pe e eeeen Ing FS oe C7000P C6000 C70hc pages 21 to 22 al ae SEOs i Common operations after installing FS 521 oy nese reee g Page E 23 to 25 MFP 120ppm 105ppm 2 series 1200 1200P 1051 e FS 521 MFP 105ppm 2 pages 8 to 10 e FS 521 RU 506 MFP 120ppm 105ppm 2 series pages 10 to 11 e FS 521 PB 503 RU 506 MFP 120ppm 105ppm 2 series pages 15to 16 e FS 521 LS 505 RU 506 MFP 120ppm 105ppm 2 series pages 17 to 18 e FS 521 FD 503 RU 506 MFP 120ppm 105ppm 2 series pages 19 to 20 e FS 521 SD 506 FD 503 RU 506 MFP 120ppm 105ppm 2 series pages 21 to 22 Common oper
9. OGYIXC011CA 4 Perform the operations described in VI Com mon operations after installing FS 521 page 23 E 14 Installation procedure for FS 521 PB 503 RU 506 MFP 120ppm 105ppm 2 series FS 521 PB 503 RU 508 EF 101 C8000 FS 521 PB 503 RU 509 7000 C 7000P C 6000 C 70hc For the installation procedure for the RU 506 508 509 see the RU 506 508 509 installation manual 1 Turn OFF the machine s Sub and Main power switches and unplug the power cord 2 Install the Installation plate 1 2 places the Installation plate 2 and the Installation plate 3 on the left side of the PB 503 as below TP screw M4x6 each 2 pcsx4 places Note For the Installation plate 2 and the Installation plate 3 use the screw holes with the engraved marking FS503 oreeeres a D annunnnnn T Installation plate 1 3 Remove the connector cover on the left side of the PB 503 1 screw Connector cover E 15 4 Install the FS 521 to the PB 503 1 Connect the four FS 521 connector plugs to the connector jacks of the PB 503 4 Ps AOGYIXCO14CA 2 Align the top and bottom holes of the FS 521 to the Installation plate 1 pins and lock them by sliding the FS 521 to the back Note 4 Secure the upper part of the FS 521 to the PB If the vertical opening between the FS 521 and the 503 with a screw TP screw M4x10 1 pc PB 503 is not even and their heights are d
10. ate 1 pins and lock them N ies P by sliding the FS 521 to the back ote For the Installation plate 2 and the Installation plate 3 use the screw holes with the engraved marking FS503 A TETTTTT Installation plate 2 7 I EELEE LELEE euunnnes k O d so 15AEIXJO16CA 15AEIXE028SB 3 Remove the connector cover on the left side of the FD 503 1 screw 15AEIXEO26SA E 19 Note If the vertical opening between the FS 521 and the FD 503 is not even and their heights are different adjust the height of the four casters of the FS 521 to make the opening even Every caster has ratchet mechanism It goes up with reciprocating the driver into the whole 1 and it goes down with reciprocating the driver into the whole 2 Be sure not to go it up too much otherwise the bolt would come off max 5mm Be sure the caster is contacting installation surface otherwise the ratchet will not work 3 Install the Connector cover TP screw black M3x4 2 pcs TP screws black M3x4 15AEIXE014CA 15AEIXE029SC 4 Secure the upper part of the FS 521 to the FD 503 with a screw TP screw M4x10 1 pc TOD 15AEIXE010CA 5 Install the Installation plate 4 to secure the lower part of the FS 521 to the FD 503 TP screw M4x10 1 pc TP screw M4x10 at Installation plate 4 gt qT f T 4 SA ae AOGYIXC011CA 5
11. ate 2 and the Installation plate 3 on the left side of the main body as below TP screw M4x6 each 2 pcsx4 places Note Ozge For the Installation plate 2 and the Installation A E T plate 3 use the screw holes with the engraved jF TUTTI HA Aa S arr marking FS503 e A E i e 2 i hF j ka a z E A 3 tose 6 Connect the short connector to the CN 19 Note Unless the short connector is connected the ISW cannot be performed TP screws M4x6 AOGYIXC003CA fil ke Po The at ae SF 5 it an a n h a e n m DADININ INN HHMI DANDIN 7 Reinstall the rear cover of the FS 521 5 screws lt i Rear cover 15AEIXE019SB E 8 8 Remove the protection bag of the FS 521 con Note nector and pull out the connector to the FS 521 If the vertical opening between the FS 521 and the rear cover side main body is not even and their heights are differ ent adjust the height of the four casters of the FS 521 to make the opening even Every caster has ratchet mechanism It goes up with reciprocating the driver into the whole 1 and it goes down with reciprocating the driver into the whole 2 Be sure not to go it up too much otherwise the bolt would come off max 5mm Be sure the caster is contacting installation surface otherwise the ratchet will not work Place to pull out the connector jack Connector jack 15AEIXE009SA
12. ations after installing FS 521 Page E 22 to 24 C8000 e FS 521 RU 508 EF 101 C8000 pages 12 to 13 FS 521 PB 503 RU 508 EF 101 C8000 pages 15 to 16 e FS 521 LS 505 RU 508 EF 101 C8000 pages 17 to 18 e FS 521 FD 503 RU 508 EF 101 C8000 pages 19 to 20 e FS 521 SD 506 FD 503 RU 508 EF 101 pages 21 to 22 Common operations after installing FS 521 Page E 22 to 24 E1 A0GY955055 ll Accessory parts Installation plate 1 Installation plate 2 Installation plate 3 Installation plate 4 P 15BMIXC002SA o 15AEIXC001CA o 15AEIXC002CA p 15AEIXC003CA Connector 15AEIXC004CA Truss screw black M4x6 TP screw black M3x4 a i a i i Holding material MFP120ppm 105ppm 2 series only Installation manual E 2 lll Confirmation Prior to Installation 1 Select a flat and stable place for installing the machine Unit weight Approx 80kg Make sure to have an adequate number of per sons for handling or carrying the machine The packaging material should not be reused for repacking Choose a location where air conditioners and other drafts do not directly blow on the main tray to prevent paper exiting failures Use the machine where the ambient light does not come in To prevent the overdrive of the main tray lV Lock Removal Procedures 1 Visually inspect the unit and remove external locking tapes and ac
13. ber Setting 5 iTouch the finisher No key according to the place where it was installed to display the Serial number entry screen Machine FS 521 Finisher 1 Machine other optional unit FS 521 Finisher 2 Machine other optional unit x 2 FS 521 Finisher 3 Enter the serial number of the FS 521 and touch OK Use Shift to switch between upper case letters and lower case letters 7 Touch Return on the serial number list screen MFP 120ppm 105ppm 2 series rr 1 Plug the power cord into the outlet and turn ON the Main power switch 2 Enter Service mode Note Refer to procedures in the Service Manual to enter into the Service Mode Touch the System Setting key 4 Touch the M C Serial Number Setting key 5 Touch the Finisher key to display the serial number setting screen Select the installa tion order key Enter the serial number of the FS 521 and touch the OK key Use Shift to switch between upper case letters and lower case letters 7 Touch the OK key on the serial number set ting screen C8000 C7000 C 7000P C 6000 C 70hc rr 1 Plug the power cord into the outlet and turn ON the Main power switch 3 Enter Service mode Note Refer to procedures in the Service Manual to enter into the Service Mode a 2 Touch the System Setting key Touch the Serial Number Setting key 5 Touch the
14. cessory parts Locking Locking tapes Locking tapes Accessory parts AOGYIXCO002CA 2 Remove the locking tapes from each guide plate V Installation Procedure and remove the locking materials 4 places Installation procedure for FS 521 RU 504 COLOR MFP 65ppm series For the installation procedure for the RU 504 see the RU 504 installation manual E aA 7 tapes a 1 Turn OFF the machine s Sub and Main power switches and unplug the power cord 2 Remove the positioning bracket top of the FS 521 two screws Locking materials u A T a r E4 a Positioning bracket top w Locking tapes 15AEIXC002CC 3 Pull out the stacker and remove the locking tapes Remove the locking materials 2 pieces within the stacker 7 ter Saal 15AEIXEO38SA Install machine installation plate L included in the RU package TP screw M4x6 4 pcs included with the RU Se 15AEIXEO39SA 4 Remove the locking tape the locking guide tape and the cushions from the stapling portion ta Pa i 4 p a e F all guide tap 15AEIXCOO5CA E 3 4 Install the blindfold plate included in the RU package TP screw M4x6 2 pcs included with the RU t me si Blindfol 4 d plate i i Ro YF mm IP screws M4x6 15AEIXE040SA 5 Connect the four FS 521 connector plugs to the connector jacks of the power supply uni
15. ctor plugs to the connector jacks of the SD 506 on the paper exit side 2 Align the top and bottom holes of the FS 521 to the Installation plate 1 pins and lock them by sliding the FS 521 to the back Installation plate 1 A 15AEIXE035SB Note 4 Secure the upper part of the FS 521 to the SD If the vertical opening between the FS 521 and the 506 with a screw TP screw M4x10 1 pc SD 506 is not even and their heights are different Ae E adjust the height of the four casters of the FS 521 7 to make the opening even Every caster has ratchet aad gm or ee mechanism It goes up with reciprocating the driver into the whole 1 and it goes down with reciprocating the driver into the whole 2 Be sure not to go it up too much otherwise the bolt would come off max 5mm Be sure the caster is contacting installation surface otherwise the ratchet will not work 5 Install the Installation plate 4 to secure the lower part of the FS 521 to the SD 506 TP screw M4x10 1 pc 15AEIXEO10CA TP screw M4x10 AOGYIXC011CA 5 Plug in the power cord COLOR MFP 65ppm series only Connect the power cord to the RU 504 and plug 15AEIXEO14CA it into the outlet included in the machine pack 3 Install the Connector cover TP screw black age M3x4 2 pcs RU 504 FD 503 SD 506 Connector cover TP screws black M3x4 i 15AEIXE066SB 15AEIXE036SB 6 Perform the o
16. ed up to both memories at the same time COLOR MFP 65ppm series MFP 120ppm 105ppm 2 series C8000 C 7000 C 7000P C 6000 C 70hc On the Service mode menu screen touch the Machine Condition key or State Confirma tion key Touch the I O Check Mode key 3 Enter 9 and 0 using the quantity setting buttons Make sure that lt 90 00 gt or appears on the message display Press the Start key Make sure that lt OUT FIN gt appears on the message display after the adjustment lt 090 00 gt Touch the Return key then touch the Exit key E 25
17. ifferent J adjust the height of the four casters of the FS 521 to make the opening even Every caster has ratchet mechanism It goes up with reciprocating the driver into the whole 1 and it goes down with reciprocating the driver into the whole 2 Be sure not to go it up too much otherwise the bolt would come off max 5mm Be sure the caster is contacting installation surface i otherwise the ratchet will not work 5 Install the Installation plate 4 to secure the lower part of the FS 521 to the PB 503 TP screw M4x10 1 pc TP screw M4x10 y AOGYIXCO1ICA 5 Perform the operations described in VI Com mon operations after installing FS 521 page 23 15AEIXE014CA 3 Install the Connector cover TP screw black M3x4 2 pcs Connector cover TP screws black M3x4 15AEIXC036SD E 16 Installation procedure for FS 521 LS 505 RU 504 COLOR MFP 65ppm series FS 521 LS 505 RU 506 MFP 120ppm 105ppm 2 series FS 521 LS 505 RU 508 EF 101 C8000 FS 521 LS 505 RU 509 7000 C 7000P C 6000 C 70hc For the installation procedure for the RU 504 506 508 509 see the RU 504 506 508 509 installation manual 1 Turn OFF the machine s Sub and Main power switches and unplug the power cord 2 Install the Installation plate 1 2 places the Installation plate 2 and the Installation plate 3 on the left side of the LS 505 as below TP screw M4x6 each 2 pc
18. perations described in the following VI Common operations after installing FS 521 page 23 E 22 VI Common operations after installing FS 521 3 Insert the sub tray into the sub tray paper exit slot 1 Install the alignment plate Fr Rr on the paper exit slot of the main tray TP screw black M3x4 4pcs on the FS 521 Note When installing the sub tray push the tray all the way in until you hear a click Alignment plate Rr Alignment plate Fr Sub tray 15AEIXJ 007CB 4 Install the main tray on the main tray up down portion on the FS 521 Truss screw M4x6 2 pcs Note When installing the main tray hook the main tray guide holes to the four auxiliary metal hooks and secure the tray 15AEIXE013CA 2 Install the holding material MFP 120ppm 105ppm 2 series only Note Refer to the user s guide for the usage of the hold ing material Main tray 15AEIXJ 008CB TR AoGYIXCO10CA E 23 Vil Serial Number Registration Register the serial number of the FS 521 to the machine memory The location of the serial number is shown in the fig ure below COLOR MFP 65ppm series 1 Plug the power cord into the outlet and turn ON the Main power switch 2 Enter Service mode Note Refer to procedures in the Service Manual to enter into the Service Mode Service Mode Menu screen 3 E Touch System Setting 4 System Setting Menu screen Touch M C Serial Num
19. rface otherwise the ratchet will not work screw M4 TP screw M4x10 AOGYIXCO11CA 4 Perform the operations described in VI Com mon operations after installing FS 521 page 23 15AEIXE014CA Installation procedure for FS 521 RU 508 EF 101 C8000 For the installation procedure for the RU 508 see the RU 508 installation manual 1 Turn OFF the machine s Sub and Main power switches and unplug the power cord 2 Install the Installation plate 1 2 places the Installation plate 2 and the Installation plate 3 on the left side of the RU 508 as below TP screw M4x6 each 2 pcsx4 places Note For the Installation plate 2 and the Installation plate 3 use the screw holes with the engraved marking FS503 Installation plate 2 i 2a FS503 7 ac o Installation plate 1 A 7 er La 7 7 1 Installation plate 3 ta Z FS503 amp i ene sy ar TP M4 TP screws M4x6 SUEN ni TP screws M4x6 AOGYIXCO06CB 3 Install FS 521 to RU 508 1 Connect the four FS 521 connector plugs to the connector jacks of the RU 508 I RU 508 i AOGYIXCO16CA 2 Align the top and bottom holes of the FS 521 to the Installation plate 1 pins and lock them by sliding the FS 521 to the back Note If the vertical opening between the FS 521 and the RU 508 is not even and their heights are different adjust the height of the four casters of the FS 521 to make
20. sx4 places Note For the Installation plate 2 and the Installation plate 3 use the screw holes with the engraved marking FS503 frrrrrers y Engraved marking FS503 nnnnnnnt a n annunnnn 7 I Installation plate 1 15AEIXE015CA 3 Remove the connector cover on the left side of the LS 505 1 screw Connector cover 15AEIXE021SA 4 Install the FS 521 to the LS 505 1 Connect the four FS 521 connector jacks to the con nector plugs of the LS 505 on the paper exit side g 2 Align the top and bottom holes of the FS 521 to the Installation plate 1 pins and lock them by sliding the FS 521 to the back Installation plate 1 15AEIXE023SB E 17 Note 4 Secure the upper part of the FS 521 to the LS If the vertical opening between the FS 521 and the 505 with a screw TP screw M4x10 1 pc LS 505 is not even and their heights are different adjust the height of the four casters of the FS 521 to make the opening even Every caster has ratchet mechanism It goes up with reciprocating the driver into the whole 1 and it goes down with reciprocating the driver into the whole 2 9 Be sure not to go it up too much otherwise the bolt a would come off max 5mm STP screw M4x10 Be sure the caster is contacting installation surface otherwise the ratchet will not work 15AEIXE014SA 5 Install the Installation plate 4 to secure the lower part of
21. t onl N a i Wi FS 521 connectors 6 Align the bottom hole of the FS 521 with the posi tioning pin on the power supply unit and lock them by sliding the FS 521 toward the back L AOGYIXCO09CA 15AEIXE041SB E 4 7 Open the front door of the FS 521 and install installation plate 4 TP screw M4x10 1 pc Installation plate 4 k 15AFIXE042SA Note If the screw holes do not match when securing instal lation plate 4 adjust the height of the four casters of the FS 521 to match the screw holes Every caster has ratchet mechanism It goes up with reciprocating the driver into the whole 1 and it goes down with reciprocating the driver into the whole 2 Be sure not to go it up too much otherwise the bolt would come off max 5mm Be sure the caster is contacting installation surface otherwise the ratchet will not work 15AEIXE014CA 8 Install the reinforcing plate R included in the RU package on the back of machine installation plate R and machine installation plate L TP screw M4x6 4 pcs included with the RU A Reinforcing plate R TP screws M4x6 15AQIXE050SA 9 Retract the supporting leg on the back side of the power supply unit 7 15AQIXC008SA 10 Place the conveyance unit on the rail of machine installation plate R and machine installation plate L and slide it all the way in until it stops at the back Machine installation plate L
22. the FS 521 to the LS 505 TP screw M4x10 1 pc TP screw M4x10 f i N N y 4 A N A N 15AEIXE015SA 5 Plug in the power cord COLOR MFP 65ppm series only Connect the power cord to the RU 504 and plug it into the outlet included in the machine package 15AEIXE014CA 3 Install the Connector cover l TP screw black M3x4 2 pcs See Pover cord g i Connector cover a gt 15AEIXE063SB eee 6 Perform the operations described in VI Com mon operations after installing FS 521 page 23 E 18 4 Install the FS 521 to the FD 503 1 Connect the four FS 521 connector plugs to the connector jacks of the FD 503 on the paper Installation procedure for FS 521 FD 503 RU 504 COLOR MFP 65ppm series exit side FS 521 FD 503 RU 506 MFP 120ppm 105ppm 2 series FS 521 FD 503 RU 508 EF 101 C8000 FS 521 FD 503 RU 509 C 7000 C 7000P C 6000 C 70hc For the installation procedure for the RU 504 506 508 509 see the RU 504 506 508509 installation manual 1 Turn OFF the machine s Sub and Main power switches and unplug the power cord 2 Install the Installation plate 1 2 places the Installation plate 2 and the Installation plate 3 Isae neona nstallation plate 2 and the Installation plate 3 on n E SEy the left side of the FD 503 as below TP screw 2 Align the top and bottom holes of the FS 5 to the Installation pl
23. the opening even Every caster has ratchet mechanism It goes up with reciprocating the driver into the whole 1 and it goes down with reciprocating the driver into the whole 2 Be sure not to go it up too much otherwise the bolt would come off max 5mm Be sure the caster is contacting installation surface otherwise the ratchet will not work AOGYIXC008CB 15AEIXE014CA E 12 3 Install the Connector cover TP screw black M3x4 2 pcs Installation procedure for FS 521 RU 509 C7000 C7000P Ce000 C70hc For the installation procedure for the RU 509 see the RU 509 installation manual TP screws black M3x4 1 Turn OFF the machine s Sub and Main power switches and unplug the power cord 2 Install the Installation plate 1 2 places the Installation plate 2 and the Installation plate 3 on the left side of the RU 509 as below TP screw M4x6 each 2 pcsx4 places Note For the Installation plate 2 and the Installation plate 3 use the screw holes with the engraved 15AEIXC029SC marking ES503 4 Secure the upper part of the FS 521 to the RU 508 with a screw TP screw M4x10 1 pc a kd a 5 Install the Installation plate 4 to secure the lower part of the FS 521 to the RU 508 TP screw M4x10 1 pc Installation plate 3 ponens om f u l f a Z FS503 ee a 7 Installation plate 2 Installation plate 1 7 S TP screws M
Download Pdf Manuals
Related Search