INSTALLATION AND USER GUIDE
Contents
1. LD4 Red Led alarm LD5 Yellow Led microwave LD6 Green Led IR Trimmer IR Range IR range adjustment MW Range MW range adjustment ae DIP Switch SW1 OO Antimask AND IR ANTIMASK Led Enabled ENABLED Enabled Antimask IR ANTIMASK Led DISABLED Disabled Disabled It is possible to set up detector for external or internal use using JP1 Jumper as described in the following chart JUMPER JP1 JP1 plugged in JP1 plugged out DETECTION LENGTH CHART 4 Lateral view m u ES LED indicator MEM input In case of alarm or masking attempt a positive signal on this clamp shows the T events LIGHTED ON FLASHING IR detection no MILII MW detection MILII RED YELLOW LED MW detection RED GREEN YELLOW IR MW detection IR antimask detection RED momen LED MW antimask detection enabled AMICGUEDHE RED MuR GREEN IR MW antimask detection enabled AMK output In case both masking and alarm condition occur first LED will light on then they Will start flashing GENERAL INSTALLATION GUIDE Perimeter protection a ae2. Stt EVTSEISESSE tT VTL Pa ee ee ae ae a a ae a aa ae a a a aa Pe ee a ee ae ea a ae a a ae a a a aa Se ee oe KARERA KEAS xS S a hx s uM my 21222 M 5 7 7 7 4 4 75 75 7 4 4 4 4 Me Oe He ia 1 7 7 4 4 7 4 7 74 75 4 4 Ds Dia ia Da Da Da Da Ba Cae a all ol a aie Sr ee rY wee ae a Sa ae ae aa aa a aa ae a a a aa a a FL Ett TBSEQISESS rY Pari a a a a a a SP ee ae oe a E RSS eh PCR ML Windows protection Windows and door protection Installation To avoid troubles on the detector it is necessary to check what follows When the detector is powered on LED indicator will flash alternatively stabilization time After that GREEN LED will flash fast and in the end YELLOW LED will flash fast GREEN LED flashing fast means that detector is acknowledging environmental conditions necessary for Beam antimask function YELLOW LED flashing fast means that detector is acknowledging conditions necessary for MW antimask function This acknowledging phase is necessary to evalue default conditions no masking condition so that any other condition can be considered as a masking attempt During this procedure do not stay in front of detector and do not put any obstacle between detector and covered area When detector will stop fl
3. We EL JE3COF2 A Art 9452 9454 DOUBLE TECNOLOGY OUTDOOR DETECTOR WITH ANTIMASKING SYSTEM INSTALLATION AND USER GUIDE TECHNICAL CHARACTERISTICS Wall munt 12m 7 5 1 Detection length 5 Detection area curtain area 7 5 see chart on page Horizontal detection area IR 7 59 MW 329 Vertical detection area IR 90 MW 80 Curtain area characteristics 2 25cm 130cm 10m Adjustable AND OR 10 15 Vcc Minimum consumption 5sec commutation after 25sec of masking Antimasking relay time time TAMPER relay Enabled disable through DIP Switch Auto compensation Dimension 37x125x40m LL WARNING To avoid the risk of damaging the product never touch the PIR sensor with hands Use a clean and soft cloth to clean the sensor GENERAL DESCRIPTION Remove screw plastic protection in the upper side of detector using a screw driver Angular reversible mounting bracket Wall mounting bracket WIRING Clamp description and purpose 12V Positive 12Vcc GND GND negative AMK Antimasking Output N C AS TAMPER N C MEM Inhibition input and alarm memory enabling positive AL Alarm output N C LED indicator
4. ashing it will start working normally e GREEN LED will show pre alarm condition IR e YELLOW LED will show pre alarm condition MW e RED LED will show detector alarm condition IR When a positive signal is present on MEM clamp usually connected to Off clamp of some control panels LED indicator are always lighted off and detector will be not working If an alarm occurs alarm memory will be shown as described in the above chart When control panel will be activated again detector will start working normally If a masking alarm occurs detector will repeat acknowledgment of environmental conditions when control panel will be activated again DETECTION OPTIONS Mw antimask When this function is enabled AMK output activates if an obstacle remains in front of detector about 25sec e IR antimask When this function is enabled AMK output activates if an obstacle remains in front of detector A IR active signal will be checked out to verify this condition IMPORTANT NOTICE We suggest to do not activate Mw Antimask function if detector is installed outside where it can be exposed to rain snow etc AND Detector will be in alarm only if MW and IR are both in pre alarm condition OR Detector will be in alarm if MW or IR are in pre alarm condition
Download Pdf Manuals
Related Search