Digidim Remote Control (303) Installation and User Guide
Contents
1. Installation and User Guide Helvar Digidim Remote Control 303 freedom in lighting Product description C The Digidim Remote 303 can be used in conjunction with the iDim Sense to modify the preset light levels and recall store scenes as well as activating its special functions 100 h Burn In PIR Walk test and Mode Identification A LED Indicator Flashes as each message is transmitted B Scene Recall Configuration C On Off Shift A D Modifier Keys 2 E Transmitter F Battery Cover C D Switching Lights On Off using Digidim 303 Remote To switch the lights On or Off 1 1 Point the remote control at a controller 1 2 Press On Off Shift key on remote control to switch the lights on or off Note Throughout this document Controller refers to iDim Sense and or Button Panels Recall Scenes using Digidim 303 Remote To recall a scene using the DIGIDIM remote 2 1 Point the remote control at a controller 2 2 Press scene key 1 2 3 or 4 to recall scene w2 P Q Modify Light Levels using Digidim 303 Remote To modify DALI 1 light levels using the DIGIDIM remote DALI 1 1 gt 100 3 1 Point the remote control at a controller 3 2 Press scene 1 Up modifier key to raise DALI 1 light level 3 3 Press scene 1 Down modifier key to lower DALI 1 light level 100 gt 1 Note To store scenes see chapter 4 To modi2. fy DALI 2 light levels using the DIGIDIM remote 3 4 Point the remote control at a controller DALI 2 3 5 Press scene 2 Up modifier key to raise DALI 2 light level 1 100 3 6 Press scene 2 Down modifier key to lower DALI 2 light level 100 gt 1 Helvar Data is subject to change without notice www helvar com I Contents Section Product description Switching Lights On Off using Digidim 303 Remote Recall Scenes using Digidim 303 Remote Modity Light Levels using Digidim 303 Remote Store Scenes using Digidim 303 Remote Special Functions using Digidim 303 Remote LED Flash Feedback Technical Data Helvar Data is subject to change without notice Page QW N gt freedom in lighting www helvar com Helvar Store Scenes using Digidim 303 Remote freedom in lighting To store a modified scene using the DIGIDIM remote 4 1 Point the remote control at a controller 4 2 Hold scene key 1 2 3 or 4 for 10 seconds to store scene IDim Sense LEDs will flash green If successful Note See LED Feedback table on final page of this document for LED information Special Functions using Digidim 303 Remote Start Stop 100 hour Burn In Mode To start or stop Burn In mode 9 1 Point the remote control at a controller 5 2 Press On Off Shift key and scene 1 at same time Note Restarting a Burn In test following a stop will amp a amp e TE cause the 100 hour counter to restart from 0 U
3. lk test is complete 100 hour Burn In Mode Sequence repeats until burn in is complete DALI Errors Sequence repeats until error clears Change from unoccupied to occupied Typically follows a PIR detection Data received from IR Remote Re enabling of IR Remote Successful upload from IR Remote Visible after storing modified settings Failed upload from IR Remote Visible when modified settings upload fails 1 Excluded from use with DIGIDIM 303 Remote Control 2 Helvar 303 Remote Control iDIM Installation and User Guide Doc D004744 issue 5 2014 08 28 Helvar Technical Data Freeda in lighting Connections No external physical connections are necessary Power Power supply 2 x IEC LRO3 AAA 1 5 V Battery Range Operating range Approximately 5 m with 22 5 angle to panels with 63 angle to multisensors Operation IR frequency 36 kHz Mechanical data Dimensions 97 mm x 28 mm x 119 mm Housing Matt dark grey non flammable polycarbonate halogen free Weight 90 g Operating conditions Ambient temperature 0 C to 40 C Relative humidity Max 90 non condensing Storage temperature 10 C to 70 C Conformity and standards Environment Complies with WEEE and RoHS directives 3 Helvar 303 Remote Control iDIM Installation and User Guide Doc D004744 issue 5 2014 08 28
4. se Dim Sense LED Feedback Resume sBurn In Mode to continue a stopped Burn In test See instruction 5 3 below for information how to do this Resume Burn In Mode To resume a stopped Burn In mode at a later date 5 3 Point the remote control at a controller 5 4 Press On Off Shift key and scene 2 Note If a Power Off On cycle occurs the counter will be reset to 0 F iDim Sense LED Feedback Mode Identification To establish which iDim Sense mode is selected 5 5 Point the remote control at a controller 5 6 Press On Off Shift key and scene 3 Start Stop PIR Walk Test 5 7 Point the remote control at a controller 5 8 Press On Off Shift key and scene 4 gt X0 1 D iDim Sense LED Feedback Note Number of flashes depends on mode selected See overleaf for detailed LED information iDim Sense LED Feedback 1 Helvar 303 Remote Control iDIM Installation and User Guide Doc D004744 issue 5 2014 08 28 Helvar LED Flash Feedback freedom in lighting Two LEDs red and green located in the iDim Sense flash to provide visual feedback for various states User Defined Mode Selected LED Flash Feedback Following an upload from IR Remote Mode 1 Selected Classroom Mode 2 Selected Single Office Mode 3 Selected Open Plan Office Mode 4 Selected Corridor Link Mode 5 Selected Corridor Hold Mode 6 Selected Meeting Room PIR Walk Test Mode Sequence repeats until wa
Download Pdf Manuals
Related Search