User guide
Contents
1. B gt O MDIG o O For missing data on one side pressure infunction of the instrument range please see the data sheet on our web side www nuovafima com Static pressure both side MD 16 100 bar MD 17 400 bar MD 18 3 3 Dynamic and cyclic pressures Not accepted 3 4 Overpressure The instrument is protected against overpressure only in case of short period overpressure disturbances In case of longer unilateral overpressure the O ring can adhere so strongly to the clamps that they do not detach regularly not even when the differential pressure decreases 3 5 Vibrations When the instrument support is subjected to vibrations we can consider different solutions such as a the use of liquid filled instruments b remote mounted instruments connected through hoses suitable for strong or irregular vibrations Vibrations can be noticed if the index keeps on oscillating 3 6 Dampening liquid filling The dampening liquid is generally used to reduce vibrations of the moving parts due to vibrations and or pulsations The dampening liquid must be chosen very carefully in case the instrument operates with oxidant media such as oxygen chlorine nitric acid hydrogen peroxide etc In presence of oxidant agents there is a potential risk of chemical reaction inflammability and explosion of the instrument In this case proper filling liquids must be used The type of the filling liquid as well as its ambient temperature2. NUERA Industrial instrumentation for Pressure and Temperature FIAT User guide DIFFERENTIAL PRESSURE GAUGE MI MD ENG _2 MD 04 2012 The instrument works in safe conditions when correctly selected and installed in the system and when the rules concerning the product as well as the maintenance procedures established by the manufacturer are respected The staff charged with the selection installation and maintenance of the instrument must be able to recognize the conditions that may negatively affect the instrument s ability to work and which may lead to premature breakage The staff must therefore be technically qualified and properly trained and must carry out the procedures called for in the plant regulations Standards Directive P E D 97 23 CE Nuova Fima instruments are designed and manufactured according to the safety rules included in the safety international prevailing standards According to the 97 23 CE standard the NUOVA FIMA pressure gauges are classified in 2 categories PS _ 200 bar these instruments should not satisfy the essential safety standards but they have only to be designed and manufactured according to a SEP Sound Engineering Practice and they do not have to bring any CE marking PS _ gt 200 bar these instruments should satisfy the essential safety standards established by the PED they are classified as category I and they are certified according to Form A They should bring the CE marking as rep
3. ral fluorolube liquid Instruments are supplied properly cleaned and degreased with special products and packed in polyethylene bags The user must take the necessary precautions to ensure that the connection and the elastic element are kept clean after the pressure gauge has been unpacked 4 3 Breakage for vibrations Vibrations most commonly cause an abnormal deterioration of the parts in mouvement bringing to a gradual loss of accuracy and then to a total block of the pointer 4 4 Dangerous process fluids In models 13 and 14 verify that fluids affecting the positive and the negative sides do not cause dangerous chemical reactions if a contact is established If this occurs we recommend to use models 15 16 or 17 When the instrument does not work correctly the sensing element can break or crack if the medium measured is inflammable and the measurement activity is continuous an explosive atmosphere could generate inside and outside the instrument case In this case it is fundamental an appropriate maintenance program through which the damaged instruments are replaced before the leakage occurs 4 5 Mechanical stress If the installation points are subjected to stress the instruments should be remote mounted and connected through hoses Instruments should be chosen among those suitable for surface or panel mounting 6 Maintenance The instrument s characteristics should be maintained during time through a special maintenance p
4. roduced below 1 1 Intended use These instruments are used to check differential pressures of gaseous liquids wich do not have high viscosity and do not crystalizee In presence of high temperature high viscosity and corrosive process fluid or which can crystalize these instruments can be fitted with remote mounting diaphragm seals Before installation be sure that the right instrument has been selected following the working conditions and in particular the range the working temperature and the compatibility between the material used and the process medium gt Warning This manual does not concern the instruments conforming to standardl 94 9 CE ATEX gt Attention The product warranty is no longer valid in case of non authorized modifications and of wrong use of the product gt Attention The manufacturer disclaims all responsibility in case of damages caused by the improper use of the product and by the non respect of the instructions reported in this manual gt Warning Follow carefully the specific safety rules in case of measuring oxygen pressure acetylene inflammable or toxic gas or liquids gt Warning The user is totally responsible for the instrument installation and maintenance gt Attention Disconnect the instruments only after depressurization of the system gt Warning The process fluids residuals in the disassembled gauges co
5. rogram on which skilled personnel should work on The instrument features must be maintained in order to prevent damages due to high temperatures risk of fire and explosion due to abnormal instrument working As for heavy work instruments operating in severe conditions plants vibrations pulsating pressures corrosive or sedimentous fluids combustible or inflammable media we recommend to schedule their replacement according to the maintenance program schedule It is recommended to verify the sensing element condition the indication pressure the sensing element corrosion level as far as the diaphragm seals are concerned the gaskets tightness and the condensate presence inside the housing In case the instrument does not work properly it is necessary to proceed to an unschedule examination procedure 6 1 Routine check In order to verify the sensing element condition install the instrument on the pressure generator introducing an interception valve between them Apply the maximum pressure value to the gauge and exclude it form the pressure source through the valve Any possible leakage of the sensing element can be noticed from the slow return of the pointer to zero In order to verify the accuracy of indication create in laboratory a stable pressure value and apply it to the instrument to be examined and to a pressure test primary testing instrument 6 2 Recalibration If after recalibration results are different from the nominal
6. trument In order to remove the instrument for maintenance much easier it is recommended to apply an shut off valve between the instrument and the system 2 1 Installation Installation should be always carried out carefully in order to prevent any pressure spike or sudden temperature fluctuations Therefore the shut off valves should be opened slowly in order to check if there are restrictions sediments or condensate which could affect the real values o a o 2 2 3 3 V O rt Please follow these instructions 1 open the by pass valve 1 2 open the root valve 3 3 open the shut off valve 2 of the plus side 4 verify that the chambers are completely filled up through the blow out vents placed on the top of the instrument 5 close the by pass valve 1 open the shut off valve 2 of the minus side _ 3 Operation limits a 3 1 Process and ambient temperature This instrument is designed to be used in safety conditions that is in an ambient temperature between 40 and 65 C As for the filled model please see the paragraph DAMPENING LIQUID FILLING INSOLE FIAI 3 2 Working pressure This instrument is designed to work with a differential pressure of 100 of the full scale range Static pressure one side w
7. uld affect people the environment and the system It is highly recommended to take proper precautions gt Warning In order to verify the working and manufacturing features of the instruments read the catalogue sheets in the most up dated edition available on line on Wwww nuovafima com Copyright Nuova Fima S p A All rights reserved Any part of this publication should not be reproduced without a written Nuova Fima s S p A approval _2 Installation and commissionig A Before installation and commissioning verify the connection distance of the instrument process connection and the possible valve where it will be installed Tighten the instrument thread forcing on the process connection area by a special wrench without forcing with the hands As for cylindric threading process connections GAS metric a head gasket compatible with the gas or fluid medium should be used If the connection thread is conic simply screw on the connection In order to imrpove the thread tightness it is recommended to wrap the male thread with PTFE tape Not suitable for cylindric threading lt A S In both cases twist through two exagon wrenches the first applied on the plane faces of the connection and the other the pressure connection We recommend to fix the instrument through a pipe or panel mounting bracket After mounting the instrument dial should be in vertical position except otherwise indicated on the ins
8. use limits should be taken into consideration Dampening liquids Working temperature Glycerinea 98 15 4 65 C 60 150 F Silicon oil 45 65 C 50 150 F 4 1 Breakage for corrosion It occurs when the sensing element material is subjected to chemical attack by the substances contained in the medium to be measured or in the ambient surrounding the pressure system The damage consists in a punctiform leakage or in a stress crack due to the material weakening The sensing element is normally characterised by a reduced thickness so it works in condition of strong mechanical stress Tehrefore the chemical compatibility with the fluid to be measured has to be taken into consideration No common material can be saved from a chemical attack which can be characterised by different factors concentration temperature and mixture of the different chemical substances 4 2 Breakage for explosion It occurs after a violent release of thermal energy due to some chemical reactions such as the adiabatic compression of oxygen in presence of hydrocarbons combustibles It is commonnly accepted that it is impossible to prevent the effects of this kind of damage Pressure gauges suitable for use with oxygen are marked Oxygen No lubrification and or they are marked with a crossed out oil can symbol nishan on the dial Also the models with double diaphragm seal are filled up between the two diaphragms with a special neut
9. values declared on the catalogue sheet the recalibration procedure should be repeated It is recommended to return the instrument to NUOVA FIMA for this procedure NUOVA FIMA will not be responsible for any non authorized intervention on the instrument Moreover the contract warranty and the CE Conformity Declaration will be no longer valid 7 Disposal It is recommended to remove the window and blow out vent before disposal as aluminium and stainless steel The fluid remaining inside the instrument can be dangerous or toxic Via C Battisti 59 61 28045 INVORIO No Italy Tel 39 0322 253200 Fax 39 0322 253232 www nuovafima com e mail info nuovafima com
Download Pdf Manuals
Related Search