Z1 OUTDOOR DMX-512 LED CONTROLLER User Manual Ver 1.0
Contents
1. ZZ KO DXOXOR Code 03 LA 009 IP65 User Manual Rel 1 0 2 Z1 OUTDOOR IMPORTANT SAFETY INFORMATION Fire prevention Never locate the fixture on any flammable surface Minimum distance from flammable materials 10 cm Replace any blown or damaged fuses only with those of identical value Prevention from electric shock High voltage is present inside the unit Unplug the unit prior to performing any operation which involves touching the inside of the unit This equipment must be grounded do not connect to non grounded supplies The use of a thermal magnetic circuit breaker is recommended for each Z1 OUTDOOR Use only AC supplies 90 260V 50 60Hz The unit should never be located in position exposed to rain or in areas of extreme humidity A good air ventilation is essential for proper equipment work Safety The external surface of the unit may exeed 50 C never handle the unit until at least 5 minutes have elapsed since the unit was turned off Never install the unit in an enclosed area lacking sufficient air flow The ambient temperature should not exeed 40 C and should not be lower than 10 C DESCRIPTION Z1 OUTDOOR DMX 512 LED controller is a unit dedicated to the following LED products by D T S MR16 RGB LED lamp MR16 full color LED lamp D30 RGB LED projector D30 full color LED projector D150 full color LED projector FOS 100 FOS 33 HELIOS FOCUS 3 channels output DMX 512 Power interface able to drive R2. D T S INFRARED REMOTE SENSOR CODE 03 LA 016 7 Pint HELIOS FULL COLOUR M12 MALE 3 HELIOS R FULLCOLOUR A E 6 Pind 7 M12 FEMALE D T S INFRARED REMOTE SENSOR CODE 03 LA 016 43 9 5 6 Pind u MALE IMPORTANT The maximum number of HELIOS Led projectors connectable to the 21 OUTDOOR Power supply Is 1 pcs Never plug in a new UNIT when the power supply is turned on Note The information contained in this publication has been carefully prepared and checked However no responsibility will be taken for any errors All rights are reserved and this document cannot be copied photocopied or reproduced in part or completely without prior written consent from D T S D T S reserves the right to make any aesthetic functional or design modifications to any of its products without prior notice D T S assumes no responsibility for the use or application of the products or circuits described herein MADE IN ITALY The Lighting Company D T S Illuminazione s r l Via Fagnano Selve 10 12 14 47843 Misano Adriatico RN Italy Tel 39 0541 611131 Fax 39 0541 611111 info dts lighting it www dts lighting it
3. 2 4 1 SEA laa 6 3 2 N DATA DATA Display WIRING DIAGRAM Z1 OUTDOOR Z1 OUTDOOR is provided with an M12 male connector 30cm cable lenght PIN CONNECTOR FEMALE FEMMINA ON BOARD Z1 OUTDOOR LEDS CONNECTOR PINOUT 1 RED 2 RED 3 GREEN 4 GREEN 5 BLUE 6 BLUE not used 8 not used RJ12 PIN CONNECTOR H E 6 pin Female RJ12 PIN CONNECTOR FEMALE FEMMINA ON BOARD Z1 Z4 LED CONTROLLER PIN CONNECTOR MALE MASCHIO ON BOARD FOS 100 FULL COLOUR FOS 33 FULL COLOUR 4 2 5 7 Pint For application where IP65 rating is not necessary Z1 OUTDOOR cabling connection can be done with a standard UTP TIA EIA 568 B2 category 5E cable The maximum distance between power supply and the unit should not exceed 100 meters For IP65 rating application D T S reccomed the use of a IP65 68 cable as the 10XAWG26 multipolar black outdoor cable IP68 D T S Code 0509C061 The maximum distance between power supply and the unit should not exceed 100 meters 5 Z1 OUTDOOR DMX SIGNAL CONNECTION The unit operates using a digital DMX 512 signal Connection between the controller and the unit or between units must be carried out using a two pair screened 80 5 mm Ensure that the conductors do not touch each other Do not connect the cable ground to the DMX connector chassis The plug housing must be isolated Connect the mixer signal to the DMX IN projector plug and connect it to the next pro
4. colour macros 10 16 Buttons VOL NAVIGATION In Automatic mode let you select the desired value for DIMMER Buttons PROG MENU In Automatic mode let you scroll between the selectable games OK PUBEN RED GREEN YELLOW BLUE buttons O Direct acces to Automatic mode for Red Green Blue Yellow colour macros Red CU01 Green CU07 Yellow CU04 Blue CU13 Navigation buttons Same as UP DOWN on unit display OK button Same as ENTER on unit display MENU button 14 Z1 OUTDOOR DMX PROTOCOL 9 CHANNELS MODE Default SHUTTER DIMMER RED GREEN BLUE WHITE Pre programmed whites at different color temperatures CTC COLOURS MACRO FUNCTIONS OON A URWN ir Parameter SHUTTER DMX range Mode Option Function Value a 5 poo Black out 10 19 4 Open 20 29 4 Black out 30 119 Strobe at variable speed from slow to fast 3400ms 20ms 120 149 Pulse open at variable speed from slow to fast 43s 100ms 150 179 Dr Pulse close at variable speed from slow to fast 43s 100ms 180 204 192 Random Strobe Master and RGB active 205 229 218 Random Strobe Full 230 255 240 Open DMX CHANNEL Parameter DIMMER En Move DAMA mung range Mode Option Function Value __ Se 0 255 Proportional dimmer _ AE Move DAMA manage range Mode Option Function Value AA grees 0 255 Po Proportionalcolour 15 Z1 OUTDOOR DM CHANNEL ES Parameter GREEN Move DAMA camge r
5. unit runs the configuration given by the received input DMX values With the channel SCENES it is possible to pass from one step to the next while with REC it is possible to record the selected scene From 235 255 the unit runs the configuration given by the received input DMX values closing the sequence as last scene With the channel REC it is possible to record the selected scene as last scene DMX channel 12 RECORDING channel Records the set scene with a variation between 0 to 255 the display flashes indicating that the scene has been recorded It is advised that you keep the REC channel set to 0 and to run through the 255 only once you have decided to save the scene If ChPr is not closed by indicating the last scene Edit channel between 235 255 in playback mode all 16 scenes will be played through even if not programmed INFRARED REMOTE CONTROL ar Button By activating Ir MODE on Z1 OUTDOOR Menu it will be possible to navigate trought the unit functions by using the D T S infrared remote control D T S Code 0514L008 Please note that external infrared remote sensor is also needed D T S Code 03 LA 016 Infrared remote control functions 1 9 ON OFF and MUTE buttons Buttons In Automatic mode let you stop the games running on Master and slaves will go in Stand by mode 1 9 buttons VOL PROG In Automatic mode let you select the colour macros 1 9 is Buttons 1 Button eave In Automatic mode let you select the
6. ATIC MODE is active only for CU01 CU16 and Wh01 Wh16 macros ChPr MASTER SLAVE The first unit that will function as a Master must be set to Automatic mode AUTO the other units must be set to Slave mode SLAV selectable through the menu In this way all the Slave units will be synchronised with the master and running their own ChPr game On the master unit it is possible to vary the Speed time SPEE for the colour changhing and the Wait time UAlt between the steps Speed time and Wait time on the Master have priority on the slave units NB It is possible to run GA Pr on the other units even though these do not have GA Pr programmed You can do this by setting the units to 9 ch DMX MODE and selecting DMX address A001 Rec mode It is possible to program your own game on the Z1 OUTDOOR that will then run it in AUTO mode ChPr Each unit can have its own programmed game In REC mode Z1 OUTDOOR unit must be set to 9 channels mode To program the ChPr by using a DMX controller you need 3 more channels in addition to the 9 channels necessary to control the unit So that in RECORDER mode via DMX the unit will need 12 DMX channels to be correctly programmed 13 Z1 OUTDOOR The three new DMX channels are DMX channel 10 SCENES channel From 0 10 no function r001 From 11 255 are displayed the programmable scenes max 16 scenes from MO01 to MOO16 DMX channel 11 EDIT channel From 0 19 no function From 20 234 the
7. GB LED units Max 25W x channel 3x 350mA electronically dimmable led control outputs Main Input voltage range is 90V 260V 50 60 HZ It is possible to use this item through every DMX 512 mixer or by using the DTS InfraRed control MAIN ELECTRICAL CHARACTERISTICS Input Voltage Range Vin 90 260 Vac Frequency 50 60 HZ Power Consumption Range 6 60 W Power Factor Pf 0 95 electronic PFC controller Efficiency 90 typical IP protection grade IP 65 Output Power Output Range 1 5 25W per channel Output Current 350 mA 100 per channel 500mA 100 per channel in BOOST Mode Output Voltage Vout 48V Max Load output 15 x FOCUS RGB LED projector or 5 x FOCUS FULL COLOUR LED PROJECTOR or1 x FOS 100 FULL COLOUR LED projector or 3x FOS 33 FULL COLOUR LED projector Min Load output 1 x FOCUS RGB LED projector Control Input Control Signal DMX 512 Dimming System Constant Current PWM Address Range DMX 512 channels addressable by display APPLICATIONS Cinemas Restaurants and pubs Discoteques Architectural Interior and Exterior 3 Z1 OUTDOOR INPUT OUTPUT CONNECTIONS Mains 90 260 Vac 50 60 Hz male connector DMX IN OUT Female Connector LED OUTPUT cable 30 cm lenght with M12 female cable connector DMX IN OUT Female Connector Infrared sensor input connector M12 LED OUTPUT CONNECTOR FEMALE ON BOARD Z1 OUTDOOR 3 MAINS DMX IN OUT MALE CONNECTOR FEMALE CONNECTOR
8. IET Mr Bo Y Mars 9104 OS Marr MAA o Y Mao 120134 oo poo Mares 135 149 oo Macro 150 164 Macro 165 179 Maro 180 194 IO Macro dt 195 209 o Y Marl 00 210 2235 Macro 226 239 Maro 00 240255 Macro O DMX CHANNEL 9 Parameter FUNCTIONS Recall Create and Store the Custom white Move DAMA range range Mode Option Function Value degrees 079 Custom White Recall Enable CH 6 for Custom white Recall 80 160 MO Custom White Create Enable CH 6 for Custom white Creation 161 255 Custom White Store Store the Custom White created 17 Z1 OUTDOOR 5 CHANNELS MODE 1 SHUTTER 2 DIMMER 3 RED 4 GREEN 5 BLUE DMX CHANNEL 1 Parmer SHUTTER DMX range Mode Option Function Value as FS Black out 1019 4 Open 20 29 24 po Black out 30119 Strobe at variable speed from slow to fast 3400ms 20ms 120 149 Pulse open at variable speed from slow to fast 43s 100ms 150 179 A Pulse close at variable speed from slow to fast 43s 100ms 180 204 192 Random Strobe Master and RGB active 205 229 218 Random Strobe Full Open 230 255 240 DMX CHANNEL Parameter DIMMER DMX range Value DMX CHANNEL Parameter RED DMX range Value DMX CHANNEL 4 Parameter GREEN DMX range Value DMX CHANNEL Parameter BLUE DMX range Value 0255 Proportional colour 18 Z1 OUTDOOR 6 CHANNELS MODE For use with DTS Wall mount
9. Led projector connectable to the 21 OUTDOOR Power supply is 1 pcs Never plug in a new UNIT when the power supply is turned on 20 Z1 OUTDOOR Z1 OUTDOOR LED UNITS WIRING CONNECTIONS o E E Bi PIN CONNECTOR A A FEMALE FEMMINA E ON BOARD i 5 Y Z1 OUTDOOR EN 2 i D T S INFRARED 7 Pint REMOTE SENSOR PIN CONNECTOR CODE 03 LA 016 MALE MASCHIO ON BOARD FOS 33 FULL COLOUR l M12 FEMALE Pi M12 MALE 5 3 1 3 NO M12 FEMALE Pin M12 MALE 5 IMPORTANT The maximum number of FOS 33 FULL COLOUR Led projector connectable to the Z1 OUTDOOR Power supply is 3 pcs Never plug in a new UNIT when the power supply is turned on 21 Z1 OUTDOOR Z1 OUTDOOR LED UNITS WIRING CONNECTIONS D T S T BOX IP65 CODE 03 LA 001 IP 65 gt 5 6 i T 7 Pint Pin1 6 PIN CONNECTOR PIN CONNECTOR M12 MALE M12 FEMALE FOCUS RGB D T S INFRARED REMOTE SENSOR CODE 03 LA 016 FOCUS RGB Z U C O C N 3 M12 MALE 5 7 IMPORTANT 6 5 l FOCUS RGB 7 Pint 6 x 7 Pini The maximum number of FOCUS RGB Led MLA MALE Ao o projectors connectable to the 21 OUTDOOR Power 1 5 _ supply is 15 pcs The maximum number of FOCUS FULL COLOUR Led projectors connectable to the 21 OUTDOOR Power supply is 5 pcs Never plug in a new UNIT when the power supply Is turned on 22 Z1 OUTDOOR Z1 OUTDOOR LED UNITS WIRING CONNECTIONS Pint 6 M12 FEMALE
10. able by user as on DMX channel 2 Dimmer Dimmer level is active for all the programs and macros SHUTTER Shutter level selectable by user as on DMX channel 1 Shutter Shutter level is active only for CU01 CU16 and Wh01 Wh16 macros ESC Esc from Automatic Mode Menu gt gt gt ENTER Up Down ENTER we 255 e ENTER Up Down ENTER wes E SCH MENU Up Down ENTER ENTER REC MODE In DMX Recorder Mode it is possible to create and store the scenes of the ChPr by using an external DMX controller The unit must be setted to 9 channels MODE DMX Recorder Mode For the programming of ChPr by using a DMX controller besides the 9 channels necessary to control the unit a further 3 DMX channels are needed So that in RECORDER mode via DMX the unit will need 12 channels to be correctly programmed The three new DMX channels are DMX channel 10 SCENES channel From 0 10 no function r001 From 11 255 are displayed the programmable scenes max 16 scenes from M001 to M0016 DMX channel 11 EDIT channel From 0 19 no function From 20 234 the unit runs the configuration given by the received input DMX values With the channel SCENES it is possible to pass from one step to the next while with REC it is possible to record the selected scene From 235 255 the unit runs the configuration given by the received input DMX values closing the sequence as last scene With the channel REC it is possible to record the se
11. ange Mode Option Function Value Se 0 255 Po Proportionalcolour DMX CHANNEL Parameter BLUE AAA Move DMX range range Mode Option Function Value ee 0 255 Proportionalcolour DMX CHANNEL 6 Parameter WHITE Pre programmed White at diff color temperature DMX range Mode Option Function Value 055 No Function 56 105 80 Full Red Green Blue at Full 106 155 130 White DTS IF CHANNEL 9 FUNCTIONS CUSTOM WHITE RECALL Dmx range value 0 79 156 205 180 Custom White Recall White CTC Channel 7 CTC enabled A 43 color temp Correction Macros 2000 K 7200 K IF CHANNEL 9 FUNCTIONS CUSTOM WHITE CREATE Dmx range value 80 160 156 205 Custom White Create RGB levels selectable by DMX 206 255 White CTC Channel 7 CTC enabled 43 color temp Correction Macros 2000 K 7200 K _DMX CHANNEL 7 Parameter CTC Color temperature correction Move DIN De nes range Mode Option Function Value degrees IF CHANNEL 6 White WHITE CTC Dmx range value 206 255 0 255 43 color temp Correction Macros 0 2000 K 128 5500 K 255 7200 K IF CHANNEL 6 White NO FUNCTION Dmx range value 0 43 0 255 Smooth RGB linear Hue correction 16 Z1 OUTDOOR DMX DMX CHANNEL 8 Parameter COLOUR MACROS Move DMX range range Mode Option Function Value O ee 014 14 NoFunction Function ST O O AR o 30 Mtr IE CI Macro
12. ed DMX controller 0514L007 1 GREEN 2 RED 3 BLUE 4 DIMMER 5 NOT USED 6 SHUTTER DMX CHANNEL 1 Parameter GREEN Move LAME carge range Mode Option Function Value EEE 0255 Proportional colour Parameter RED Move DD mai range Mode Option Function Value EEE EEE 0255 O ee Proportional colour Parameter BLUE Move MOS made range Mode Option Function Value E 0255 Proportionalcolour Parameter DIMMER Move DINDS cage range Mode Option Function Value A uo 025 Proportional dimmer E Parameter NOT USED Move ES else range Mode Option Function Value _ AO 0 2255 NoFunctioono O a ea Parameter SHUTTER DMX range Mode Option Function Value Black out a A Open ws a Black out 30 119 Strobe at variable speed from slow to fast 3400ms 20ms 120 149 Pulse open at variable speed from slow to fast 43s 100ms 150 179 Pe Pulse close at variable speed from slow to fast 43s 100ms 180 204 192 Random Strobe Master and RGB active 205 229 218 Random Strobe Full 230 255 2400 Open 19 Z1 OUTDOOR Z1 OUTDOOR LED UNITS WIRING CONNECTIONS PIN CONNECTOR FEMALE FEMMINA ON BOARD Z1 OUTDOOR 2 7 Pint PIN CONNECTOR MALE MASCHIO ON BOARD D T S INFRARED FOS 100 FULL COLOUR REMOTE SENSOR CODE 03 LA 016 FOS 100 FULL COLOUR IMPORTANT The maximum number of FOS 100 FULL COLOUR
13. ile reset is running press the MENU and ENTER keys at the same time Reset EEPROM Reset all settings ATTENTION by pressing this key you must repeat all previous calibrations UPLOAD This menu allow to upgrade the unit s software by computer DOWNLOAD This menu allow to save unit s programs into computer EXIT Exit from hidden menu 11 Z1 OUTDOOR AUTOMATIC OPERATION AUTO Z1 OUTDOOR can work in automatic mode without a DMX controller First of all connect the projectors with a DMX cable picture below A maximum quantity of 32 slave units can be connected to the same Master unit MASTER SLAVE 1 SLAVE 2 SLAVE 3 SLAVE 32 E T gt EN a es d To activate Auto mode on the first unit use the menu to run through the different modes until AUTO appears on the display and press enter Now it is possible to choose between the different pre programmed games CUPr RAIn CU01 CU16 Wh01 Wh16 or ChPr which is user programmable through REC mode To confirm game activation press ENTER on the selected GAME CUPr RAIn CU01 CU16 Wh01 Wh16 The first unit that will work as a Master should be placed in Automatic mode AUTO the other units have to be placed in 9 channels DMX mode MODE 9CH and the DMX address should be set at A001 For Raln rainbow game it is possible to select the speed for the colour changhing SPEE DIMMER function in AUTOMATIC MODE is active for all the programs SHUTTER function in AUTOM
14. jector 1 A001 Projector 2 A009 If you want to select the next projector just add 8 DTS Wall mounted DMX controller 0514L007 assign 8 DMX Projector 3 A017 channels per unit also if some channels are not used ME A projector6 A041 If you want to use the Z1 OUTDOOR in 9 channels mode select the 9 CH mode from the MODE menu and set the following addresses on the mixer Projector 1 A001 Projector 2 A010 If you want to select the next projector just add 9 Projector 3 A019 a A projector 6 A046 Selelcting the DMX address 1 Press the UP DOWN key until you reach the required DMX address The numbers on the display will start to flash but the new DMX address hasn t yet been set 2 Press ENTER to confirm your selection The numbers on the display will stop flashing and the projector is now controlled by the new DMX address TIPS if you keep pushed the UP or DOWN keys the channels are calculated more quickly and you get a faster selection 7 Z1 OUTDOOR DISPLAY FUNCTIONS DFP Digital Function Panel MENU ENTER DOWN DISPLAY FUNCTIONS The Z1 OUTDOOR display panel shows all the available functions Using these functions it is possible to change some of the parameters and add some functions Changing the D T S setting can vary the functions of the unit so that it does not respond to the DMX 512 signal used to control it Carefully follow the instructions below before carrying out any variations or
15. jector by connecting the DMX OUT plug on the first unit to the DMX IN plug of the second one In this way all the projectors are cascade connected CONTROLLER P S If the display showing the DMX address flashes then one of the following errors has occurred DMX signal not present DMX reception problem For Installations where long distance DMX cable connections are needed we suggest to use a DMX terminator The DMX terminator is a male DMX cable connector with a 120 ohm resistor Between pin 2 and 3 The DMX terminator must be plugged into the DMX out panel connector of the last unit connected to the DMX line DMX MALE CABLE CONNECTOR GND DATA DATA 120 OHM PLACE A 120 OHM RESISTOR BETWEEN PIN 2 AND 3 OF A MALE DMX CONNECTOR AND PLUG IT INTO THE DMX OUT PANEL CONNECTOR OF THE LAST UNIT CONNECTED TO THE DMX LINE 6 Z1 OUTDOOR DMX ADDRESS Z1 OUTDOOR can be used in three different modes 5 6 or 9 DMX default channels If you want to use the Z1 OUTDOOR in 5 channels mode select the 5 CH mode from the MODE menu and set the following addresses on the mixer Projector 1 A001 Projector 2 A006 If you want to select the next projector just add 5 Projector 3 A011 aed Ain projector 6 A026 If you want to use the Z1 OUTDOOR in 6 channels mode select the 6 CH mode from the MODE menu and set the following addresses on the mixer To be used only with DTS Wall mounted DMX controller 0514L007 Pro
16. lected scene as last scene DMX channel 12 RECORDING channel Records the set scene with a variation between 0 to 255 the display flashes indicating that the scene has been recorded It is advised that you keep the REC channel set to 0 and to run through the 255 only once you have decided to save the scene If ChPr is not closed by indicating the last scene Edit channel between 235 255 in playback mode all 16 scenes will be played through even if not programmed MENU Up Down SLAVE MODE Slave mode for ChPr program All slave units will be synchronised with master unit running their own Chpr program 10 u gt TS i ENTER ENTER Up Down ENTER Z1 OUTDOOR IS 02 gt 012 MENU Up Down ENTER Up Down INFRARED MODE Infrared remote control By activating Ir MODE it will be possible to navigate trought the unit functions by using the D T S infrared remote control D T S Code 0514L008 m Z pr m 7 NOTE External infrared remote sensor needed D T S Code 03 LA 016 ex ts MENU Up Down ENTER ENTER DEFAULT To restore default settings MENU Up Down ENTER Up Down ENTER LIFE TIME This menu show the total UNIT life tine and the RGB life time ez IS MENU Up Down ENTER TEST MODE RGB colours test with rainbow MENU Up Down SOFTWARE Software version id ENTER 11 Z1 OUTDOOR HIDDEN MENU For technical personnel only To operate this menu Connect the unit to the main Wh
17. low to select the value of the delay in millisecons for RGB and Dimmer channels reaction to DMX or Program variation Off 25 ms delay Fast response 20 250 ms delay Slow response COMPRESSION This menu allow to select between Linear courrent output or Quadratic courrent output for LEDs Default Linear Up Down 8 Z1 OUTDOOR TE A a ve ENTER Up Down ENTER ENTER ENTER Up Down ENTER ENTER ENTER Up Down ENTER Default 25 RSP ENTER Range Off 20 I ENTER Up Down Default 2 ENTER Off 25 ms Istant responce to DMX variation 20 250 ms Smooth response to DMX variation Linear Linear ENTER Up Down courrent output ENTER Quadratic Linear light ENTER output US BF SUr E US p Down ENTER ENTER Up Down AUTOMATIC MODE Automatic demo game without DMX controller ChPr Chase with 16 steps previously created in REC MODE Speed and Wait time selectable by user CUPr RGB values selectable by user Rainbow rAln Rainbow colours effect Speed time selectable by user CU01 CU16 Color Macros as on DMX channel 8 Macro gt gt ENTER gt gt Up Down ENTER gt gt ENTER Up Down FAS gt gt ENTER 00 105 Up Down gt ENTER Up Down ENTER Z1 OUTDOOR MENU Up Down ENTER ENTER Up Down ENTER Up Down ENTER AUTOMATIC MODE Automatic demo game without DMX controller WHITE MACROS 16 macros for White color from 2000 to 7200 K DIMMER Dimmer level select
18. selections NOTE the symbol ps gt shows which key has to be pushed to obtain the desired function Software version 1 07 ks RR ks E RS gt Floor IS MENU Up Down ENTER Up Down ENTER Up Down position ENTER REVERSE DISPLAY Reverses display s reading depending on Suspension ES Z m y the mounting position position E On the ground or suspended Up Down IS gt ENTER Up Down a Display OFF DISPLAY STAND BY To turn off the display after 5 seconds Or leave it always on Display always ON ENTER E a TS soe Up Down ENTER Up Down ENTER DMX MODE ie To select DMX mode 5 6 9 default Up Down 6 CHANNELS ENTER DMX channels 9 CHANNELS IS Default DMX Mode 9 CH Up Down ENTER 3 FS Up Down ENTER Up Down BOOST DRIVING This menu allow to increase the Up Down LED s current from 350mA to 500 mA Boost mode activated I Whit BOOST active the LED s current is setted to 500mA IP 30 more gain ENTER Default Disable Boost mode deactivated IS gt IS IS MENU Up Down ENTER Up Down LED RGB Min Max Smooth and Compression level values settings Up Down RGB MINIMUM VALUES This menu allow to select the minimum levels for Red Green and blue RGB MAXIMUM VALUES This menu allow to select the maximum levels for Red Green and blue Up Down IE These settings have priority on Master Dimmer DMX channel 2 Up Down SMOOTH VALUE This menu al
Download Pdf Manuals
Related Search