USER MANUAL
Contents
1. Always turn on the transmitter first then the ESC to prevent an out of control vehicle Disconnect the battery from the ESC after use Never leave the vehicle unsupervised while it is switched on in use or connected to a power source If there are exposed wires do not use the ESC until you have installed shrink wrap or replaced the wire If there is a short circuit or product defect it could result in fire When programming your ESC or calibration function disconnect motor or remove the pinion gear The Electronics in this vehicle are not waterproof and you must avoid running the vehicle in or through standing water wet grass mud or snow If your vehicle gets caught or stuck do not pull the throttle in either forward or reverse This will overload the ESC and or motor resulting in damage to one or possibly both and is not covered by your warranty After running a battery pack allow the electronics several minutes to cool before running the next battery pack ee NP amp EP REMOTE CONTROL CAR I Nitro Power Car Power Car Engi Adjustment High end mixture valve To measure the fuel inflow and provide high end mixture lf screwing it further in the high end mixture volume will decrease Once you unscrew it in the high end mixture volume will increase Low end mixture valve To measure the fuel inflow and provide low end mixture You are required to adjust low end mixture valve to pro vide an even process for running yo2. that enters the carburetor can immediately damage your engine Clean the air filter after every hour of running You can wash the foam filter with warm water Dry the filter then re apply air filter oil to the foam filter Pre run Check e Keep your vehicle clean by using a brush to remove dirt and dust e Check for cracks in the suspension arms and other molded parts e Check the tires are still glued to the wheels i e Check all the wheel bearings are clean and lubricated e Check all the screws and nuts are tightened e Check all the camber links and steering linkage are not bent e Check all the toe and camber settings are as desired and equal e Check the spur gear e Check the pinion gear e Check the slipper pads e Check the shocks if they appear leaking rebuild them e Check all the wiring and connections for bare wire or any place which could lead to a short circuit e Check all the electronic components are securely mounted to the chassis e Check the receiver is still securely mounted to the chassis e Turn on the radio If the battery LED is off or dim replace the batteries in the transmitter e Keep safe distance from your vehicle while you are making adjustment ce NP amp EP REMOTE CONTROL CAR I Nitro Power Car Power Car Maintenance after driving Proper maintenance is very important Make sure to always perform appropriate maintenance after driving so that you can enjoy driving without problems n
3. children e Always remove the LiPo battery if model is involved in any kind of crash Carefully inspect the battery and connectors for even the smallest damage CAUTION cells may be hot e Do not allow the electrolyte to get into eyes or on skin Wash affected areas immediately if they come into contact with electrolyte Do not alter or modify connectors or wires of a LiPo battery pack e Always inspect the condition of the battery before charging and operating e Do not short circuit the LiPo battery e Do not have contact with a leaky damaged battery directly e Do not charge battery out of recommended temperature range OC 45C The vehicle is equipped with an nimh battery always follow these safety instructions e Never dispose of NiMH batteries in a fire or store near sources of heat e Only use the supplied NiMH charger to charge the NiMH battery Using another charger may permanently damage the battery and surrounding components and e Batteries should only be charged on a fireproof surface away from any flam e Never leave the battery unattended when charging or discharging e Batteries must be discharged or fully exhausted before being disposed of Cover exposed poles with adhesive tape to prevent short circuiting e Never disassemble or alter the battery contacts Do not damage or puncture battery cells Doing so would result in an explosion hazard Fg Electric Power Car Power Car NP amp EP REMOTE CONT
4. yours to avoid that loose control your car or disturb other driver Please follow up a experienced person when you drive your car as the beginner 5 Please keep away from Fire ad the model car come with plastic and electric material P oN Can enlarge collecting area if pull out the receiver antenna and will enlarge radio area if pull out radio antenna Must turn on the switch of Radio then turn on the switch of Receiver Must turn off the switch of Receiver then turn off the switch of radio and take the connector out for the battery Se O E E Nae eran qn emneeencemy This product is not a simple toy It is an authentic R C model For better performance some adjustment and correct assembly are necessary Use the battery properly Incorrect battery will damage your model and or radio system This product is strongly recommended for the user over 14 ages NP amp EP REMOTE CONTROL CAR Safety Information Shock Maintenance After each day of running you should check your shocks for adequate fluid If the fluid is low or it is getting dirty you should change the fluid in the shocks To achieve better performance you may also want to change the shock fluid and or the pistons Setting The Gear Mesh Gear mesh is the clearance between the pinion and spur in an electric car or clutch bell and spur in a nitro car It has impact on the vehicles
5. DIATELY If your engine does not start after 10 pulls Set the choke to the vertical position Pull the starter cord for upto 5 pulls until you hear the engine try to start Be careful not to flood the engine Return the choke to the horizontal position Pull the starter cord and your engine should start within 5 pulls Only use the choke in the vertical if the engine does not start normally Using the choke in the vertical position can easily flood the engine Tips Engine Break In and Running Break in procedure is essential for you to maintain performance of a brand new engine Break in procedure normally requires you to perform a trial running consuming a full gas tank slowly with a Half throttle It is not recommended that you adjust the carburettor during break in procedure Only after break in procedure is performed your engine is ready for normal running and can be adjusted To stop your engine press the engine STOP button Do not touch the engine and exhaust pipe immediately unless they totally cool down Driving Driving an R C car can be very difficult to master but here are some basic tips to help you to understand how to use it before you have your first attempt Drive the vehicle in a very large space especially until you get the feel of driving the product Do not run on public streets or highways This could cause serious accidents personal injuries and or property damage Do not run in water or sand
6. Make sure everyone is using different frequencies when driving together in the same area If you keep pulling the throttle trigger on the transmitter the vehicle will keep accelerating and run very fast It is difficult to steer thevehicle running at high speed until you become used to driving Drive the vehicle slowly by pulling the throttle trigger to the fullest and quickly releasing it You can turn the vehicle right or left while it is running When the vehicle is running toward you you need to operate the steering wheel in the opposite direction to the operation when the vehicle is running away from you Practice turning the vehicle referring to the following Rather than just paying attention to the direction of the steering wheel imagine that you are at the centre of the steering wheel looking ahead of the vehicle to turn in the direction you like Once you become conformable driving the vehicle practice driving on a track with cones Keep practising until you feel comfortable with the steering throttle and brake at low speeds Once you are feeling comfortable try using reverse When you have mastered the basics you will be able to drive at higher speeds in a more controlled fashion 1 5 SCALE READY TO RUN GASOLNE VERSION it im Engine Optional Tuning Itis a good idea to make sure your air filter is clean before attempting any engine tuning Before tuning your engine you must make sure that you have f
7. ROL CAR Care And Manintenance SELINA Naess e Always use clean damp cloth to wipe the vehicle clean Keep the vehicle and batteries away from direct sunlight and or direct heat sources e Never let the vehicle come into contact with water as this may damage the electronics Structural repairs or modifications to the product are only permitted using approved original replacement or tuning parts Otherwise the vehicle coule be damaged or coule be dangerous In order to avoid danger always operate the vehicle in position you can escape from quickly if necessary Always tum the vehicle and controller off after use e Insert new batteries in the controller or recharge as soon as any function becomes diminshed Controller Battery Safety Advice e Do not charge non rechargeable batteries e Rechargeable batteries must be removed from the controller before charging e Rechargeable batteries must only be charged under adult supervision e Do not use different types of batteries or mix old and new batteries Only use the recommended batteries or batteries of an equivalent type e We recommend using new alkaline manganese batteries for the controller To help the environment consider replacing the disposable batteries for this controller and for other household electronic items with rechargeable batteries We recommend eneloop batteries Sanyo e Insert batteries following the correct polarity and e Remo
8. USER MANUAL ACCESS TO HOBBY CAR This manual is applied to Electric Nitro Gasoline cars of any scales In order to understand our company products more expediertly please check it according to the part number Notes gt Read and understand the instructions carefully before operating or assembling your racing model Specifications are subject to change without prior notice and actual received model may vary from the images and or descriptions in this manual introduction i We would like to welcome you to the world of remote control cars What are RC cars The simple answer is that they are radio controlled cars that respond precisely to your command The more complete answer is that they can be a great addition to your lifestyle RC car building and racing teach valuable mechanical and electrical skills promote teamwork e The product is not intended for those under 14 years of age without proper adult supervision The product is not a toy Itis a precision machine requiring proper assembly and setup to avoid accidents and it is the responsibility of the owner to operate this product in a safe manner as it can cause serious personal injury and damage to property due to carelessness or misuse e Do not attempt to disassemble or modify any of the product components without the assistance of an experienced RC user e Only use the correct type of battery to operate Using any wrong type of battery will damage the p
9. e sure to always perform appropriate maintenance after driving so that you can enjoy driving without problems next time Completely remove all dirt and debris from the vehicle especially in the suspension drive shafts and steering parts Inspect each part and screw for loosening missing or damages You should always make sure your wheels are tight and parts move freely after and before use Every tank of fuel you should check chassis maintenance charge the receiver battery and also check the pull starter cord Every 5 tanks you should check the air filter and transmission If you run in dirty conditions this should be done every 2 3 tanks Every 10 tanks you should check the wheel beadlocks tyres clutch brakes shocks differentials fuel tank spark plug and engine These are recommended guidelines for checking your components Gasoline Power Car Trouble Shooting Please read this section if you have any fault trying to operate the vehicle 1 5 SCALE READY TO RUN GASOLNE VERSION Problem Engine Does Not Start Cause Out of fuel Remedy Fill the tank with fuel and prime engine Air Filter is blocked Check air filter clean or replace if necessary Throttle isn t adjusted properly Adjust the carburettor back to factory settings Throttle servo is not setup correctly Set throttle to neutral and adjust the throttle linkage Pullstart is not working Check Pull Starter and repair if
10. e the model indoors in a climate controlled room temperature environment e Never shorten the receiver antenna or this might affect the transmitting range of the radio system e This product is a RC hobby model do not use for other purpose Pe NP amp EP REMOTE CONTROL CAR Before Operating Your Vehicle The packaging contains the following when the box is opened 1 Onecar 2 one radio controller 3 charger 4 manual 5 antenna pipe For electric cars please see if it contains the following Battery Body Battery Compartment Engines Fuel Tank Exhaust Pipe Servo 2 Receiver Battery requirements for the controller Power supply DC 12V Batteries 8 x 1 5 V AA not included Batteries 4x 1 5 V AA not included Glow Plu For battery compartment Fuel Bottle Fuel Refiller Igniter 9 y 3 0mm pr S 25mm pr S 3 0mm G Hex Screwdrivers Large Mini Screwdrivers Scissors 4 way Cross Wrench Body Reamer Model Glue Small Curve Nose Pliers Needle Nose Pliers For Nitro Electric Models NP amp EP REMOTE CONTROL CAR Safety Informati Please open box and check to avoid missing parts Include a car transmitter and manual in the box Take out your car radio and manual and take off car body 3 Please Check radio and receiver must be with same frequency check inch
11. ectric power Battery without power or wire getting loose Recharge and check wire Motor wire loose Motor damaged Do not turn on switch for your radio while the motor is running Check motor wire connecting Change new motor Check TH trim in neutral position or not No driver power Connect with ESC Check each part around the steering servo Steering servo is not connect with ESC Steering servo is locked or no performance Out of control Pull throttle trigger the car go backward Steering wheel right but car going left or turns left and car going right Steering Reverse Check TH trim ST Rev switch 4 5 SCALE READY TO RUN GASOLNE VERSION Gasoline Power Car Turning on the R C Unit Turn on the transmitter first followed by the receiver or speed control Always check you have control of the servos and electronic speed control if applicable Check the range of operation before starting your engineor running Turning off the R C Unit Only turn off the R C Unit once you have stopped the car and stopped the engine if applicable Turn off receiver first and then turn off transmitter Always disconnect the battery connector from the receiver speed control after driving Trim Setup You need to check that your trims are correctly set before you start the engine or use the car Once you have turned the RIC unit on adjust thesteering trim to make sure the front whe
12. els are pointing straight A You also need to check that you have correct settings on the throttle and brake linkage The carburettor should be fully closed at neutral and thebrake should not be engaged Check that the carburettor opens fully on acceleration and that the brake engages when you pull on the brake You should re set the electronic speed control if you notice any lag in the throttle or brakes This will set up the throttle and brakes on your electricCar Fail Safe Operation and Setup The Receiver has a built in failsafe The failsafe will automatically go to a pre set position if You lose radio signal power runs out in transmitter If you suffer any interference If your receiver battery runs out of power It is advised that you should set the failsafe so that in the event of any of the above situations the throttle servo should apply brakes to your car orthe throttle disengages on a speed control To set up your failsafe you must do the following Turn on the transmitter and the receiver Apply the desired amount of brakes on the transmitter brakes for engine neutral for speed control Press the binding button on the transmitter twice in quick succession To check the failsafe is working you must turn on the R C unit and then apply throttle with the transmitter Whilst holding throttle turn off thetransmitter The throttle servo should return to the pre set position This means the failsafe is working correctly If yo
13. end mixture valve e Observe the speed of your running car with throttle set to high Your car will still speed up when you screw in the high end mixture valve at an angle of 10 or 20 degrees Hale adjustment serew e If you screw in the high end mixture valve further the engine will become overheated and subject to damage e Slow engine response is due to an over rich condition When air and fuel mixture is too rich lots of smoke and popping sound from exhaust will be observed You should screw in the high end mixture valve at an angle of approx 30 degrees turnning clockwise Hesitation from idle to mid throttle is due to a lean condition When air and fuel mixture is too light almost no visible smoke is observed and engine may quit for no appa rent reason If itis the case you should also unscrew in the high end mixture valve at an angle of approx 30 degrees turnning anti clockwise Using The Proper Fuel And Glow Plug Using the proper fuel and glow plug is important to achieve maximum performance and reliability You must use fuel glow plugs and air filters that are specifically designed for remote control model car The engine is brand new it must go through proper break in procedure to perform reliable and achieve maximum performance During the break in procedure it is common to go through one or two glow plugs failure All car engines must use a properly oiled air filter to keep dirt out of the engine Any dirt
14. ext time Completely remove all dirt and debris from the vehicle especially in the suspension drive shafts and steering parts Inspect each part and screw for loosening missing or damages Use premium After Run Oil This lubricant is perfect for maintenance of your engine Correct lubrication of all bearings and moving mechanism is necessary for proper operation You should always make sure your wheels are tight and parts move freely after and before use Troubleshooting Please read the section if you have any fault trying to operate the vehicle Check if fuel tank is empty or the carburetor is not primed correctly Fill the fuel tank up or prime the throttle The glow plug is bad or batteries are dead Replace the glow plug or charge the batteries Carburetor is not adjusted properly The engine fails to start Set the high slow end mixture valve and idle adjustment screw to original position The fuel lines the air filter or the exhaust pipe is clogged Clean or replace the clogged parts The engine is flooded Remove the glow plug and discharge excessive fuel Servo linkage is not adjustment properly Set the servo to neutral then re adjust it Fuel tank may run out of fuel Fill up the fuel tank The fuel lines the air filter or the exhaust pipe is clogged Clean or replace the clogged parts The carburetor is not adjusted properly Re adjust the high slow end mixture valve and idle adjustment screw The en
15. gine is flooded Allow the engine to thoroughly cool down and turn the high end mixture valve open at an angle of approx 30 degrees The engine can start but stall immediately Carburetor is not adjusted properly Re adjust high low end mixture valve Weak response of engine Low fuel pressure level is observed Install the pressure line from the exhaust pipe to fuel tank correctly Batteries are weak Replace or charge them Radio antenna is installed incorrectly Extend the transmitter antenna fully to obtain better reception Servo linkage is weak to control Centre the servo and perform a due adjustment again Model becomes tough to control Electric Power Car S Power Car NP amp EP REMOTE CONTROL CAR Maintenance after driving 1 Do not forget to turn off power and remove male plug and cut off power 2 Cleaning your car 3 Do not use Chemical cleanser to clean chassis to avoid electronic device getting damp and wire weld and plastic part to be corrosive Please use soft brush to cleaning you car Troubleshooting Please read the section if you have any fault trying to operate the vehicle Question Reason Solution ESC getting over heat or getting E Cool down and try again Car can not running No Performance Power problem Check wire loose or not Motor over heat Motor drive gear too tight Cool the motor and adjust drive gear No el
16. ing switch must be in neutral position to avoid destroy servo Check whether shocks leaking oil or not Take out manual from PE bag and put the antenna into the antenna pipe 4 5 Check receiver wireless is in good condition or not Can not control steering and throttle 6 7 Install 1 5v alkaline batteries for radio and for receiver turn on the switch for radio and then receiver Turn the steering wheel to check the steering direction turn right the car shall turn right adjust ST reverse switch if the car is running opposite direction The car shall be gone straight when the steering wheel back Neutral position adjust ST trim if not Pull throttle trigger and the car will go forward and adjust TH reverse switch if not Push throttle trigger and the car will stop and then backward and adjust TH reverse switch if not When the throttle trigger back neutral position the can shall be at idle speed condition adjust TH trim if not 8 Fill in nitro oil into the tank and break in the engine before drive you car wn Warning Notes Do not drive your model car when it is raining or thundering to keep safety Keep your model car in dry normal temperature condition and keep away from water Please do not use other optional parts to install our model car if you can not make sure it can match your car or not And please do not over load or use it to do breaking local law 4 To make sure nobody is using same frequency as
17. irst start of your engine is the most important time of the engine s life dictating how well it will perform Do not skip the break in process of a new engine Without proper break in procedures you risk damaging your engine during the first tank of fuel Your patience during these procedures will be rewarded by an engine that performs reliably and to its maximum power potential Patient and knowledge are the key for a successful break in process Glow plug failure is a common occurrence when breaking in a new engine When tuning the needle valves for maximum performance adjust them in small increments 16 turn at a time An engine should not be run too lean doing so severely shortens the life of the engine Itis better to run a little rich than too lean Engine Maintenance You need to perform periodic maintenance in order to keep your engine in proper operating condition After each day of running it s important to do the following steps 1 Empty all fuel from the tank and fuel lines 2 Remove the glow plug and air filter and add 5 to 6 drops of a quality after run oil into the carburetor and cylinder head openings 3 Turn the engine over a few times to distribute the oil throughout the engine 3 Clean and inspect the engine air cleaner and fuel system Checking After Start T e Verify engine performance after start up Pay close attention to exhaust smoke and engine sound High end mixture valve Low
18. ke it away from your car Please make sure battery in cool condition before recharge battery to keep battery performance running well and get a longer use life 1 Connect with manins jack e Never charge a lithium polymer battery with a charger designed for NiCd NiMH or any other type of battery chemistry Use ONLY charger designed for LiPo battery e Do not leave LiPo battery unattended during charging e Do not overcharge the battery e Always place the battery on a heat resistant surface alone when charging Always put the LiPo battery inside a charging protection container while charging e Do not allow LiPo cells to overheat at any time Cells which reach greater than 140 Fahrenheit 60C will usually become damaged and will catch fire e Do not charge LiPo cells on or near combustible materials including paper plastic carpets vinyl leather and wood inside an R C model or full size automobile e Do not discharge LiPo doing so will damage the battery e Do not expose LiPo cell to water or moisture at any time may also lead to injury mable materials e Keep the NiMH battery away from children Lithium Polymer LiPo Cc w 3 Remove charger plug out 2 Connect with battery Battery Warnings e Do not store battery near open flame or heater e Do not assemble LiPo cells or pre assembled packs together with other LiPo cells or packs e Always store LiPo battery in a secure location away from
19. necessary Choke lever position Make sure choke lever is in the correct positio Spark plug not working correctly Check Spark plug and ignition coil and replace if necessary Is the plug wire in good condition Replace plug wire if itis damaged is the engine stop switch working correctly Check and replace engine stop switch if it is broken Are the piston and cylinder in good condition Check piston and cylinder for wear and damage and replace if necessary Engine starts then stalls Fuel mixture is too old Out of fuel Make new fuel mixture Fill the tank with fuel and prime engine Air Filter is blocked Check air filter clean or replace if necessary Throttle isn t adjusted properly Adjust the carburettor back to factory settings Throttle servo is not setup correctly Set throttle to neutral and adjust the throttle linkage pr Do you have a clutch problem Check clutch for damage Engine is overheated Allow engine to cool and then restart Idle speed is set too low Adjust the idle speed Do you have a drivetrain problem Check drivetrain for damage Engine runnign but car Fuel mixture is too old Are the brakes stuck Make new fuel mixture Make sure there is no brake drag at neutral doesn t move Do you have a clutch problem Check clutch for damage Receiver battery capacity is low Charge receiver battery Do yo
20. performance If the gear mesh is not set properly you may also damage the clutch bell and spur or the pinion gear and spur gear as soon as the vehicle starts running Scheme Of Installation Anttenna Receiver Battery Nitro Radio System Please read and understand all instructions before switching on your radio system You should turn on the transmitter and then the receiver to center your servo first Turn off the receiver and then the transmitter after the servo is centered properly Receiver Antenna a J i z q j Power Switch I Receiver Crystal A 7 fo jO Battery Compartment mEn se E J 1 s ens N Warning L E Failure to observe the above instruction 5 will 5 Receiver cau se lose of control of your model I NP amp EP REMOTE CONTROL CAR 7 Electric Power Car Power Car Charge Battery N Connect charger plug with mains jack and then connect with connector of battery Please be care of safety while charging please remove charger plug from the mains jack once finish charging Will be over heat if it is too long to be charging or incorrect charging way must stop charging if over 45 degree for the battery temperature 3 Do not charge for battery at once when you ta
21. rnal engine parts a rich air glow fuel mixture is required to perform a break in procedure for your engine Important notes Break in period 2 and 1 2 turns from full closed position 4 5 tanks of 10 15 fuel 20 oil content must be used to perform break in Please do not run engine full throttle for long periods during break in Once break in procedure has been performed lean out engine to best performance 2 turns to 1 and 1 2 turns from full closed position you must always observe a trace amount of oil smoke from exhaust pipe if you hardly see any smoke please stop immediately and re adjust high end mixture valve till smoke is observed High End Mixture Valve Carburetor Inlet Opening Always perform high end mixture valve adjustment firstly and then perform idle adjustment on a warmed up engine Clean out engine and exhaust system by applying high throttle 3 4 throttle for 2 seconds after adjustment to permit effectiveness of adjustment to be observed Itis of normal occurrence during the break in procedure that minuscule particles of metal adhere to the glow element The particles of metal isolate the glow element and affect overall engine performance Lubrication We highly recommend a Premium glow fuel with a Synthetic Castor blend of a minimum of 16 and maximum of 20 combined lubricant content NitroPowerCar Power Car NP amp EP REMOTE CONTROL CAR Starting Your Engine For The First Time The f
22. roduct and possibly make it dangerous to operate e The motor s may get hot during use Always allow 10 15 minutes between each operation for the motor to cool down This will prolong the life of your product e Choose an appropriate operating site consisting of flat smooth ground and clear open field Do not operate near buildings high voltage cable lines or trees to ensure safety operation Operate in safe area only away from other people RC models are prone to accidents failures and crashes due to a variety of reasons including lack of maintenance user error and radio interference Users are responsible for their actions and damage or injury occurring during the operation e Do not operate in inclement weather such as rain wind snow or darkness e The product is composed of precision electrical components It is critical to keep the product away from moisture and other contaminants Do not allow them to get wet Electrical damage may occur that could affect safe operation e You should complete a successful pre run check of your radio equipment and model prior to each run e Use replacement parts from the original manufacturer to ensure safe operation e Operate this product within your ability Do not operate under tired condition and encourage racers to test their skills with other racers from around the world Whether you are just having fun racing your car in your backyard or racing at the world compe
23. teries get hot during charging discontinue charging immediately and disconnect the battery from the charger Never leave battery unattended while charging If you are unsure of how to charge this battery please seekthe advice of experienced RC users Never let children charge the battery without adult supervision e Always turn on the transmitter before connecting the battery on the model When turning off the model always disconnect the battery first and then turn off the transmitter If the order is reversed the model may become uncontrollable and cause serious damage e If you are in doubt of your ability to operate the model we strongly recommend that you seek assistance from experienced RC users or join your local modeling club to gain the required knowledge and skill As the manufacturer and distributor we assume no liability for the use of this product e Before turning on your model and transmitter please check to make sure no one else is operating under the same frequency Frequency interference can cause your model or other s models to crash The guidance provided by experienced RC users will be valuable for the assembly tuning trimming and actual first flight e Never allow batteries to run low or you might lose control of the model e Plastic is very susceptible to damage or deformation due to extreme heat and cold climate Do not store the model near any source of heat such as oven or heater Stor
24. tition contest radio controlled car racing is a great hobby We has been making RC products aimed at making our hobby fun and exciting with an affordable price We are confident that your experience with our products will be positive Of all the radio controlled models out there no question about it RC cars are the hardest to operate This user manual covers a wide range of topics from nitro powered remote control cars to electrical powered remote control cars We highly recommend that you read this user manual throughly and carefully before assembling and operating Please follow all precautions and recommendations located within the manual Be sure to retain the manual for future reference routine maintenance and tuning This product is nota toy It is not recommended for children under 14 years old and any minor should be accompanied by an adult when operating This product is a precision machine that requires proper assembly and setup to avoid accidents Failure to take caution when operating this product may result in serious injury or property damage It is the owner s responsibility to operate this product in a safe manner Manufacturer and its distributors are not responsible in any way for any and all bodily injury s and or property damage that may occur from the use of or caused by in any way or this product e After each use always allow the battery to cool down before recharging When charging the battery pack do not overcharge If bat
25. u have a drivetrain problem Check drivetrain for damage Erratic control Is the failsafe system working Weak batteries in transmitter and receiver Make sure failsafe system is working properly Install fresh batteries Transmitter or receiver is off Turn on both transmitter and receiver Transmitter reverse switches are set incorrectly Check the reverse switch settings Transmitter End Point Adjustments EPA are set incorrectly Check your EPA Dials on your transmitter Brake does not work Set throttle to neutral and adjust the brake linkage If you encounter any other fault whilst operating the vehicle please contact your local hobby shop or alternatively contact your local distributor ie
26. ully warmed it up Do this by driving for a good 5 minutes or so You have 2 needles on the carburettor that you can adjust The Top End needle and Bottom end needle If your Top Speed is slow then you can adjust the Top End needle To increase the top speed you need to turn the Top End needle clockwise by no more than 1 16th increments ata time NEVER GO MORE THAN 1 4 TURN FROM STD SETTINGS If you go more than that it will damage your engine If your car accelerates slowly you can adjust the Bottom End needle To increase acceleration you need to turn the Bottom End needle clockwise by no more than 1 16th increments at a time NEVER GO MORE THAN 1 4 TURN FROM STD SETTINGS If you go more than that it will damage your engine A possible cause for slow acceleration is a damaged clutch If you do not get the performance you require please check the clutch and replace any damaged parts You can also adjust the Idle Speed of the engine by adjusting the Idle Speed ne dle clockwise for higher idle and anti clockwise for a lower idle If you are not sure if the tuning you have made is correct then you can re set the engine to factory settings Engine Factory settings Make sure the Top End and Bottom End needles are fully tightened clockwise Top End needle is then opened anti clockwise 1 and 1 4 turns Bottom End needle is the opened anti clockwise 1 and 1 2 turns Maintenance after driving Proper maintenance is very important Mak
27. ur engine from low High Speed Needle Valve Fuel Inlet Adjustable High Speed Needle Valve Carburetorinlet 5 Carburetor inlet Fuel Inlet Adjustable Idle Stop Adjustment Low Speed Needle Valve speed to high speed Idle adjustment screw To control the air and fuel mixture which flows into the car buretor while the engine is at Idle from stalling at an extremely low Carburetor inlet To mix the air and fuel to permit a proper running of your engine After attached with an air filter itis used to ensure a good proportion Take a moment to review the figures on the right to familiarize yourself with the various functions of the engine Although preset at the factory some changes in the needle setting can occur during shipping Engine image is represented for reference only It may vary from the actual received engine The engine includes many high precision parts Incorrect operation or rash assembly and disassembly will compromise the proper performance of your engine Engine Break In Period New engines require a break in period to exercise a final adjustment of internal parts after manufacturing For our models we have already perform this procedure before putting them on the market However you will use your own engine to drive our models This procedure is required and must be completed by you the user To prevent excessive initial wear on inte
28. ur servo does not return to thepre set position then you must try to re set your failsafe Recoil Starter Stop Switch Fuel Inflow Mouth Glow Plug Fuel Composition Unleaded Gasoline Stroke Oil Gasoline about 75 z Stroke Oil about 25 Please mix the two different Clutch Bell fuel to start your engine Note The engine is sticked with warning labels Throttle Lever a A ro e OE please pay special attention on it The image is inflowing presented for your reference only Air Back Needle Valve Air inflow switch Gasoline Power car SP 1 5 SCALE READY TO RUN GASOLNE VERSION Engine Starting Petrol 2 stroke oil You must mix your petrol fuel with 2 stroke oil with a mixture of 25 1 4 Litres 460 ml The Fuel Tank is 700CC on the MT which should give around 40 minutes 1 Gallon 5 4 fl Oz duration on atank of fuel 2 Litres 80 mi To fill the fuel tank remove the lid and use a nozzle to help with pouring the fuel 1 2 Gallon 2 6 fl Oz Once full replacethe lid and make sure it is tight 1 Litres 40 ml You need to prime the engine by pressing the priming bubble on the carburettor until you get fuel in the bubble and fuel tube 1 4 Gallon 1 3 fl Oz Make sure the choke lever is in the horizontal position before pulling the starter cord Pull the starter cord in short pulls 50cm 20 MAX until the engine fires up IF YOU HAVE ANY PROBLEMS PRESS THE ENGINE STOP BUTTON IMME
29. ve dead batteries from the controller e Do not short circuit the supply terminals Remove batteries from the controller when they are not used for a long period of time 1 10th scale The electronic speed controller ESC on this model is designed to operate with 7 2v 1800mAh 3600mAh Ni MH battery only Operating beyond the ESC s recommended specification using the incorrect type of battery or higher Voltage battery might damage the ESC 1 16th scale The electronic speed controller ESC on this model is designed to operate with 7 2v 1100mAh 1500mAh Ni MH battery only Operating beyond the ESC s recommended specification using the incorrect type of battery or higher Voltage battery might damage the ESC Electronic Speed Controller Caution 1 10th scale Brushless power The electronic speed controller ESC on this model is designed to operate with 7 2v Ni MH battery 8 4V Ni MH battery or 7 4v lithium polymer battery only Operating beyond the ESC s recommended specification using the incorrect type of battery or higher Voltage battery might damage the ESC 1 16th scale Brushless power The electronic speed controller ESC on this model is designed to operate with 7 2v1500 2000mAh Ni MH 8 4v1100mAh Ni MH or 7 4v2000mAh Li Po battery only Operating beyond the ESC s recommended specification using the incorrect type of battery or higher Voltage battery might damage the ESC
Download Pdf Manuals
Related Search