OPERATING INSTRUCTIONS for the heat press Secabo
Contents
1. seca bo OPERATING INSTRUCTIONS for the heat press Secabo TP10 Congratulations on purchasing a Secabo heat press Please read these operating instructions carefully so you can start production with your press without problems Reproduction of these operating instructions in any form requires the written approval of Secabo GmbH We reserve all rights to change technical data and product features Secabo GmbH does not assume any liability for direct or indirect damage resulting from use of this product Version 1 0 22 04 2013 Brief overview Secabo TP10 pneumatic heat press The newly developed heat press Secabo TP10 is for professional textile printers of large objects With an extra large work area of 75 x 105 cm the transfer press is particularly suitable for heat transfers on expansive media such as flags sheets or room dividers made of textile The base plate acts as a drawer which allows comfortable arranging of transfer objects and can be handled despite its size with little effort The pressure of the TP10 transfer press is produced by compressed air which means working with consistent and reproducible results The pneumatic head of the heat plate allows due to vertical contact pressure a flawless transferring of various materials without displacement effects etc The Secabo TP10 heat press with a heat output of 5 1 KW is suitable for all standard transfer processes and thus can be used in almost all areas of technology trans2. ady been made during the current session The counter can be reset at any time Operation Pneumatic connection Connect the TP10 to your air compressor with the included pneumatic adapter Insert the tube of the supplied adapter in the pneufit connection at the rear of the TP10 heat press The other end of the adapter will be connected with the compressor Charge the compressor with 6 8 bar up to 10 bar is possible Set the desired pneumatic pressure on the manometer of the TP10 by pulling up the cap at the top end and then turning it After the pressure is set push the cap back down The set pressure should be lower than on the manometer of the compressor Commonly used pressures are between 3 and 6 bar Power supply Connect the heat press to a 400 V power socket 3P N PE using the connection cable supplied It is recommended to have the TP10 connected by an electrician It is mandatory to assign the right lead of cables Switch on the press with the red rocker switch Operation and setting After a short self test lines appear in the display Press the OK button Use UP or DOWN to set C or F and press OK Use UP or DOWN to set the desired temperature and press OK Use UP or DOWN to set the desired time and press OK The press is heating up to the desired temperature Operating transfers e Pull out the base plate at the front side with the centered handle and put on the transfer objects Af
3. fer Short overview Secabo TP10 transfer press Pneumatic heat press for large batches Fast and simple time and temperature specification comparison of target and performance values with digital display Flexibly adjustable contact pressure by manometer with oil and water separator Two hand operation emergency off switch emergency stop for pneumatic cylinder with pre press function e CE certificate RoHS certificate inspected according to German safety standards Safety Precautions Please read these instructions and safety precautions carefully before using your press for the first time e Never reach into the heat press with your hands when it is connected to the power supply particularly when it is switched on and heated up danger of severe burns e Never manipulate the buttons for two hand operation the emergency off switch or another component on the transfer press Never open the housing or attempt to modify the machine yourself In case you are requested by the Secabo customer support to open the heating plate cover please make sure you are wearing respiratory protection and only touch the contained insulation wool with gloves Any disposal of the wool must be contained in a closed bag Ensure that liquids and metal objects do not get into the inside of the heat press Ensure that the power socket used is grounded Note that it is only permissible to operate a heat press from a power socket protected by a ground fault protec
4. ir in alleiniger Verantwortung dass das unter Technische Daten genannte Produkt mit den Bestimmungen der folgenden EG Richtlinien und Normen bereinstimmt We herewith declare under sole responsibility that the under technical data mentioned product meet the provisions of the following EC Directives and Harmonized Standards e EG Richtlinien EC Directives e 2006 95 EG Niederspannungsrichtlinie 2006 95 EC Low Voltage Directive e 98 37 EG Maschinenrichtlinie 2006 42 EG ab 29 12 2009 98 37 EC Directive on machinery from 2009 12 29 2006 42 EC e Norm Standard EN 60204 1 2006 Technische Dokumente bei Technical documents at Secabo GmbH Hochstatt 6 8 85283 Wolnzach Germany Fi I Pa Fa j i Eu oy Pal rol Fa a ff Eii i ip j af ie F L nn Dipl Ing Fabian Franke Q a if Dipl Ing FH Bernhard Schmidt
5. m high 150s 180s mugs Sublimation on tiles 200 C high 120s 480s depending on thickness of material Sublimation on jigsaw 200 C light medium puzzles Sublimations 200 C medium 20s 40s Free Sublimation on textiles on textiles a C medium medium high 308 508 50s Sublimation on metal 200 C high 10s 50s plates depending on thickness of material Important note You should carry out your own tests with the transfer material and backing to be used before starting production The values given above and the manufacturer s own figures are only intended as a guide You should establish the washability and behaviour during transfer in your own tests The recommended values do not imply a guarantee The user is responsible for determining and using the appropriate setting for his particular conditions Note for textile work After pressing allow textiles to cool down before removing any type of backing from the transfer material The hot glue in the transfer material develops its adhesive force only in the cold state If the adhesive does not stick in the cold state it may have been pressed too cold or for too short a time Technical data Pressure setting Setting of pneumatic pressure on the manometer Power supply 3P N PE 5 1kW It is recommended to have the TP10 connected by an electrician Dimensions B x H x T 110cm x 90cm x 140cm Konformit tserkl rung Statement of Conformity Hiermit erkl ren w
6. terwards push the base plate completely backwards e Now use both hands to push each one of the two buttons on the left and right of the press head to lower the heating sheet The timer starts running as soon as the press is closed After the set time has expired the TP10 opens automatically By pressing the red button next to the controller the transfer process can easily be stopped at any time e g for pre pressing garments The settings cannot be changed during pressing Each time the pressing process is completed the counter display increments by one after the set time has expired Note Please note that a certain time is required before the press cools down after it is switched off Maintenance and cleaning Maintenance work should always be accomplished with the press switched off and cooled down The plug must first be disconnected from the power socket Consult Technical Support before carrying out any maintenance work Clean the press regularly with a soft cloth and mild household cleaner to remove adhesive residues etc Never use scouring sponges solvents or gasoline Clean the drain valve by draining oil and water through the drain valve Recommended times and temperatures These values are only guidelines they can vary from material to material and should always be checked before pressing Ten rn O e Sublimation fex flex 180 C 195 C C 195 C medium mediumhign 108 358 35s Sublimation ceramic 200 C mediu
7. tion switch Disconnect machine from power outlet when not in use Never operate the heat press within the reach of children and never leave the machine unsupervised when switched on Ensure that the machine is used only in dry rooms Pay attention that the used compressor is attuned to the air consumption and the pressure need of the TP10 in tank volume and maximum pressure Only use pressure tanks that possess the necessary TUV certificates If you cannot observe one or more of the safety precautions above or if you are not sure whether all points are satisfied please contact our Technical Support Department Scope of Delivery Before starting work please check whether the following items are all present Pneumatic adapter for air compressor connection Machine description manometer oil and drain valve rocker switch fuse connecting cable back side not shown two hand control buttons time and temperature controller a9 oo Secabo GmbH Hochstatt 6 8 85283 Wolnzach Germany mail secabo com www secabo com e emergency stop for pneumatic system pre pressing button f heating plate g base plate retractable as a drawer Controller secabo With a large digital controller temperature C und F and pressing time can be adjusted The green digits are showing the theoretical value the white digits are showing the actual value A counter at the right bottom counts the number of transfers that have alre
Download Pdf Manuals
Related Search