User manual for hand switch Joggle Mount your Joggle Connect
Contents
1. standing This device have 5 memories position memories Press menu button stand icon 1 time to come to set memory menu e Use arrow up and down to navigate to set memory setting P P Press Menu Enter and the value are stored The display confirm by flashing 3 times and then returns to normal mode Units Choose between metric or Imperial system Press menu button stand icon 5 time to come to set memory menu 4 a ii bel Press Menu Enter to confirm Adjust the settings with the arrows up or a v Imperial inches Metrics centimeters 1 CM Press Menu Enter and the setting are stored 16 Calibrate Measure the distance between the floor and the top of the table sheet Press menu button stand icon 2 times to come to calibrate menu 6 4 Press Menu Enter to confirm O Adjust the figures to the selected value with the arrows up or down pP rt m Press Menu Enter and the value are stored Q 13 Reset away Press menu button stand icon 6 time to come to set memory menu i Press Menu Enter to confirm a a Press down and hold until the columns have gone to the lowest position Do reset if any parts have been changed of if you discover interference between the columns 17 Upper limit Set the upper limit if there are limit2. USER MANUAL JOGGLE Programmable hand control with display optional Display layout Explanation of the symbols QW Tool ue Imperial inches M Memory Fk Thermometer E Error codes th Reset CM Metric centimeter 15 sec sleep mode Display backlight will go to sleep mode after 15 sec of inactivity Mount your Joggle Use the 2 attached screws for fixing to the ta ble top If the thickness of the table top is less than 18 mm please use shorter screws In situation of sloped edges of the table top there could be need for a third fixing point When screw will be chosen consider that 13mm will be lost due to the hand switch Start up Initial display communication Under normal condition the display automa tically went to display layout as right in 2 to 5 sec If the system feel a incomplete homing the homing icon well be visible Press the down symbol for homing Connect your Joggle Connect the Bus cable to the hand switch If appropriate connect two bus cables to the hand switch Reset If some components are changed columns motor control for motors etc there will be need for a forced reset Please follow the instruction below Forced Reset If the reset symbol will be visible please press 2 bottoms min 7 sec the reset symbol will show up r 13 Then press and hold down symbol until the columns have gone to lowest level Whee
3. ed space in height Press menu button stand icon 3 time to come to set memory menu cy Press Menu Enter to confirm Adjust the figures to the chosen level with the arrows up or down Press Menu Enter and the value are stored Please notice that the figures count from the table top surface 14 Error codes o 1 Hard stop 2 Back off 3 Soft stop 4 Waiting for button 5 Waiting for button release 6 Motor lost Overheating Thermometer flashing wait 10 minutes for motor cooling 18
4. l icons How to understand the symbols Al Adjust the table upwards Scroll in the menu e Adjust the table to sitting position Scroll to left in the menu D Menu press for the menu Enter confirm your selection hd Adjust the table downwards Scroll in the menu Md Adjust the table to standing position TT Scroll to right in the menu 6 Quick start Run Drive the table to the position you will store sitting or standing Two different processes Press the menu button and hold for more than 2 sec Press sitting Press standing left side right side memory 1 memory 2 5 T Go to memory 1 Go to memory 2 Press and hold 10 How to go to memory Press the menu button less than 2 sec Use arrow up and down to navigate to memory setting Hold Menu button to go to the stored position Lower limit Set the lower limit if there are device equipme ntwich could create a risk of pinching or risk for table damages Press menu button stand icon 4 time to come to set memory menu i gt Il Press Menu Enter to confirm Adjust the figures to the chosen level with the arrows up or down qQ Ga a Aj Press Menu Enter and the value are stored Please notice that the figures count from the table top surface calibrated level 15 How to set memory Run Drive the table to the position you will store sitting or
Download Pdf Manuals
Related Search