ASRock IMB-A180-H Owner's Manual
Contents
1. connector PIN Signal Name PIN Signal Name 1 APU_DBRDY 2 APU_TDO 3 GND 4 APU_TDI 5 GND 6 APU_TMS 7 GND 8 APU_TCK 9 APU_DBREQ 10 APU_BTN 11 PWR_ 1 8V 12 SYS_RST 13 APU_LDT_RST 14 SMB_CLK 15 GND 16 SMB DATA 17 NC 18 X 21 Chapter 3 UEFI SETUP UTILITY 3 1 Introduction This section explains how to use the UEFI SETUP UTILITY to configure your system The UEFI chip on the motherboard stores the SETUP UTILITY You may run the UEFI SETUP UTILITY when you start up the computer Please press lt F2 gt or lt Del gt during the Power On Self Test POST to enter the UEFI SETUP UTILITY otherawise POST will continue with its test routines If you wish to enter the SETUP UTILITY after POST restart the sys tem by pressing lt Ctl gt Alt lt Delete gt or by pressing the reset button on the system chassis You may also restart by turning the system off and then back on Because the UEFI software is constantly being updated the following UEFI setup screens and descriptions are for reference purpose only and they may not exactly match what you see on your screen 3 1 1 Menu Bar The top of the screen has a menu bar with the following selections Main For setting system time date information Advanced For advanced system configurations Tool Useful tools H W Monitor Displays current hardware status Boot For configuring boot settings and boot priority2. 31 30 29 28 252423 22 0 Oo OR Co M OO A ON ND MN PN O DAN DOA LVDS Panel Panel Backlight Power Jumper Inverter Power Control Header Panel Backlight amp Audio AMP Volume Control Header COM Port Pin9 Power Setting Jumper For COM1 COM Port Pin9 Power Setting Jumper For COM2 Backlight Control Signal Setting Header LVDS Power VDD Power Jumper 4 Pin CPU FAN Connector AMD Debug Header 20 pin ATX Power Input Connector USB2 0 Port USB8 SATA3 Connector Chassis Intrusion Header 1 ATX AT Mode Jumper Digital Input Output Power select USB2 0 Connector USB67 Digital Input Output Pin Header COM Port Pin9 Power Setting Jumper For COM3 COM Port Pin9 Power Setting Jumper For 3 Pin Chassis FAN Connector System Panel Header RS 232 Port 4 Pin Header COM6 RS 232 Port 4 Pin Header COM5 RS 232 Port 4 Pin Header 4 RS 232 Port 4 Pin Header Printer Port Header Clear CMOS Header TPM Header Front Panel Audio Header 3W Audio AMP Output Wafer LVDS panel connector is for IMB A180 only HDMI1 port on the panel is for IMB A180 H only 1 4 1 0 Panel 1 USB 2 0 Ports USB01 8 USB 2 0 Ports USB4_5 2 Serial Port COM1 9 USB 3 0 Ports USB2_3 3 Serial Port COM2 10 HDMI Port HDMI2 4 LAN
3. Though this motherboard provides a 4 Pin CPU fan Quiet Fan connector 3 Pin CPU fans can still work suc cessfully even without fan speed control If you plan to connect a 3 Pin CPU fan please connect it to Pin 1 3 Please connect a fan cable to the fan connector and match the black wire to the ground pin Signal Name SPKL 1 Serial Port Header 9 pin COM3 see p 8 No 26 9 pin COM4 8 25 9 COM5 see p 8 24 9 pin COM6 see p 8 No 23 RRXD1 DDSR 1 CCTS 1 20 These COM headers sup port serial port modules Digital Input Output Pin Header 10 pin JGPIO1 see p 8 No 18 PIN Signal PIN Signal Name 1 Digital Output 0 2 Digital Input O 3 Output 1 4 Digital Input 1 5 Digital Output 2 Digital Input 2 7 Digital Output 3 Digital Input 3 9 JGPIO 10 GND Chassis Intrusion Header 2 pin see p 8 No 14 1 Signal GND This motherboard supports CASE OPEN detection feature that detects if the chassis cover has been removed This feature requires chassis with chassis intrusion detection design ATX Power Connector 20 pin ATXPWR1 see p 8 No 11 AMD Debug Header 17 pin J1 see p 8 No 10 lolol 919 19 Please connect ATX power supply to this
4. 5V 3 pin PNL_PWR1 see p 8 No 8 14 ATX AT Mode Jumper 1 2 3 PWR_JP1 RUP 2 3 ATX Mode see p 8 No 15 Digital Input Output Power 1 2 12V select uio 2 3 5V 3 PWR_JP1 see p 8 No 16 Backlight Control Signal aoo 1 2 3V Level Setting Jumper pee 2 3 5V Level 3 pin BKT_CTL1 see p 8 No 7 COM Port Pin9 Power 1 2 12V Setting Jumpers Loe 2 3 5V 3 pin SET CM1 see p 8 No 5 3 pin SET_CM2 see p 8 No 6 3 pin SET_CM3 see p 8 No 19 3 SET 4 see p 8 20 15 2 4 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers Do NOT place caps over these headers and connectors ing jumper caps over the headers and connectors will cause permanent damage to the motherboard LVDS Panel Connector PIN Signal Name PIN Signal Name 40 pin LVDS1 1 LVDS_PWR 2 LVDS_PWR see p 8 No 1 3 3V 4 DDC CLK 5 DDC DATA 6 LVDS1 DO 7 LVDS1 00 8 GND 9 LVDS1 D1 10 LVDS1 D1 11 GND 12 LVDS1 D2 13 LVDS1 02 14 GND 15 LVDS1 D3 16 LVDS1 03 17 GND 18 LVDS1 CLK 19 LVDS1CLK 20 GND 21 LVDS2 00 22 LVDS2 00 23 GND 24 LVDS2 D1 25 LVDS2 D1 26 GND 27 LVDS2 D2 28 LVDS2 D2 29 LVDSPWREN 30 LVDS2 D3 31 LVDS2 D3 32 GND 33 1 082 34 LVDS2CLK 35
5. Security For security settings Exit Exit the current screen or the Setup Utility 22 3 1 2 Navigation Keys Use lt gt key lt gt key to choose among the selections on the menu bar and use lt gt keyor lt gt key to move the cursor up or down to select items then press lt Enter gt to get into the sub screen You can also use the mouse to click your required item Please check the following table for the descriptions of each navigation key 23 3 2 When you enter the UEFI SETUP UTILITY the Main screen will appear and display the system overview 24 3 3 Advanced Screen In this section you may set the configurations for the following items CPU Configuration Chipset Configuration Storage Configuration Super IO Configuration ACPI Configuration USB Configuration and Trusted Com puting Setting wrong values in this section may cause the system to malfunction 25 3 3 1 CPU Configuration PSS Support Use this to enable or disable the generation of _ _PSS and PCT objects PSTATE Adjustment Use this to adjust PSTATE PPC Adjustment Use this to adjust PPC NX Mode Use this to enable or disable NX mode SVM Mode When this is set to Enabled a VMM Virtual Machine Architecture can utilize the additional hardware capabilities provided by AMD V The default value is Enabled Configuration options Enabled and Disabled C
6. occur the updated version will be available on ASRock s web site without further notice You may find the latest VGA cards and CPU support list on ASRock s website as well ASRock website http www asrock com If you require technical support related to this motherboard please visit our website for specific information about the model you are using www asrock com support index asp 1 1 Package Contents ASRock IMB A180 H IMB A180 Motherboard Mini ITX Form Factor 6 7 in x 6 7 in 17 0 cm x 17 0 cm ASRock IMB A180 H IMB A180 Quick Installation Guide ASRock IMB A180 H IMB A180 Support CD 1 x I O Panel Shield 1 2 Specifications MB Dimension Mini ITX Form Factor 6 7 in x 6 7 in 17 0 cm x 17 0 cm CAP All Solid CAP Fanless Fan or Fanless Depend on GPU used CPU AMD eKabini SOC GX 420CA 4 25W 2 0GHz GX 415GA 4Core 15W 1 5GHz GX 210HA 2 9W 1 0GHz System Memory 2 x 204pin SO DIMM One Channel Up to DDR3 1600 MHz Display IMB A180 Embedded Radeon DirectX 11 1 graphics support VGA LVDS up to 2 ch 24 bits 1920x1200 resolution HDMI 1 4a Support Dual Display any two display devices of VGA LVDS HDMIs Display IMB A180 H Embedded Radeon DirectX 11 1 graphics support VGA 2 x HDMI 1 4a Support Dual Display any two display devices of VGA HDMI when using the two HDMI d
7. on the system CSM Please disable CSM when you enable Fast Boot option The default value is Enabled 31 3 3 6 USB Configuration USB 2 0 Controller Use this item to enable or disable the use of USB 2 0 controller USB 3 0 Controller Use this item to enable or disable the use of USB 3 0 controller Legacy USB Support Use this option to select legacy support for USB devices There are four confi guration options Enabled Auto Disabled and UEFI Setup Only The default value is Enabled Please refer to below descriptions for the details of these four options Enabled Enables support for legacy USB Auto Enables legacy support if USB devices are connected Disabled USB devices are not allowed to use under legacy OS and UEFI setup when Disabled is selected If you have USB compatibility issue it is recommended to select Disabled to enter OS Setup Only USB devices are allowed to use only under UEFI setup and Windows Linux OS Legacy USB 3 0 Support Use this option to enable or disable legacy support for USB 3 0 devices The default value is Enabled 32 3 3 7 Trusted Computing Security Device Support Enable to activate Trusted Platform Module TPM security for your hard disk drives 33 3 4 Update Utility Instant Flash Instant Flash is UEFI flash utility embedded in Flash This convenient update tool allows you to update system UEFI
8. 2 Navigation Keys iie dece ies 23 3 2 Main cuiii 24 3 3 Advanced 25 3 31 CPU Configuration i 26 3 3 2 Chipset 27 3 3 3 Storage Configuration 29 3 3 4 Super IO Configuration 30 3 3 5 ACPI Configuration 31 3 3 6 USB 32 3 3 7 Trusted Computing 33 SA cS 34 3 5 Hardware Health Event Monitoring 35 3 0 Boot creen eere Linen aa manne 36 3 7 Security Screern 37 3 8 SCreen ie aee retener tense pede trien 38 1 Introduction Thank you for purchasing ASRock IMB A180 H IMB A180 motherboard a reliable motherboard produced under ASRock s consistently stringent quality control It delivers excellent performance with robust design con forming to ASRock s commitment to quality and endurance In this manual chapter 1 and 2 contains the introduction of the mother board and step by step hardware installation guide Chapter 3 and 4 con tains the configuration guide of BIOS setup and information of the Support CD Because the motherboard specifications and the BIOS software might be updated the content of this manual will be subject to change without notice In case any modifications of this manual
9. GND 36 B L ENABLE 37 B L ADJUST 38 BLT_PWR 39 BLT_PWR 40 BLT_PWR Inverter Power Control PIN Signal Name Header 1 1 GND 6 pin BLT PWR1 2 GND see p 8 No 3 3 B L ADJUST 4 B L ENABLE 5 LCD BLT VCC 6 LCD BLT VCC 16 Panel Backlight 8 Audio 1 AMP Volume Control Header 7 VOL1 see p 8 No 4 PIN Signal Name VOL_UP VOL_DW BKT_ON OFF BKT_UP BKT_DW GND GND NP OO gt Serial Connector 1 see p 8 13 7 11 2 0 9 pin USB6_7 see p 8 No 17 USB12 see p 8 No 8 This Serial connector supports SATA data cables for internal stor age devices The current interface allows up to 6 0 Gb s data transfer rate Besides four default USB 2 0 ports on the I O panel there is one USB 2 0 header and one USB port on this motherboard Each USB 2 0 header can support two USB 2 0 ports Print Port Header 25 pin LPT1 AFD ope see p 8 No 27 17 This is an interface for print port cable that allows conve nient connection of printer devices This connector supports 17 pin TPM1 E Trusted Platform Module see p 8 No 29 5 TPM system which E securely store keys digital certificates passwords and data A TPM system also helps enhance network se curity prot
10. RJ 45 Port LAN1 DASH 11 HDMI Port HDMI 5 LAN RJ 45 Port LAN2 12 D Sub VGA1 6 Front Speaker Lime 13 PS 2 Keyboard Mouse Port 7 Microphone Pink There are two LEDs on each LAN port Please refer to the table below for the LAN port LED indications FER LAN Port COM1 COM2 RS232 422 485 Pin Mapping DCD Data carrier detect RXD Receive data TXD Transmit data DTR Data terminal ready port on the panel is for IMB A180 H only 10 Chapter 2 Installation This is a Mini ITX form factor motherboard Before you install the mother board study the configuration of your chassis to ensure that the mother board fits into it Pre installation Precautions Take note of the following precautions before you install motherboard com ponents or change any motherboard settings 1 sure to unplug the power cord before installing or removing the motherboard Failure to do so may cause physical injuries to you and damages to motherboard com ponents 2 n order to avoid damage from static electricity to the moth erboard s components NEVER place your motherboard directly on a carpet Also remember to use a grounded wrist strap or touch a safety grounded object before you handle the components 3 Hold components by the edges and do not touch the ICs 4 Whenever you uninstall any components place them on a grounded anti static pad or in the bag t
11. later use Step 3 Align the card connector with the slot and press firmly until the card is completely seated on the slot Step 4 gt Fasten the card to the chassis with screws 13 2 3 Jumpers Setup The illustration shows how jumpers are setup When the jumper cap is placed on pins the is Short no jumper cap is placed pins the jumper is Open The illustration shows 3 pin jumper whose pin1 and SN vien pin2 are Short when a jumper cap is placed on these 2 pins Clear CMOS Jumper 12 23 3 pin CLRCMOS1 mo see 8 28 Default Clear CMOS CLRCMOS allows you to clear the data in CMOS To clear and reset the system parameters to default setup please turn off the computer and unplug the power cord from the power supply After waiting for 15 seconds use a jumper cap to short pin2 and pin3 on CLRCMOS 1 for 5 seconds However please do not clear the CMOS right after you update the BIOS If you need to clear the CMOS when you just finish updating the BIOS you must boot up the system first and then shut it down before you do the clear CMOS action Please be noted that the password date time user default profile 1394 GUID and MAC address will be cleared only if the CMOS battery is removed Panel Backlight Power Jumper 1 2 5V 3 pin BKT_PWR1 123 2 3 12V see p 8 2 LVDS Power VDDR Power 1 2 3V Jumper Les 2 3
12. without entering operating systems first like MS DOS or Win dows Just save the new UEFI file to your USB flash drive flop py disk or hard drive and launch this tool then you can update your UEFI only in a few clicks without preparing an additional floppy diskette or other complicated flash utility Please be noted that the USB flash drive or hard drive must use FAT32 16 12 file system If you execute Instant Flash utility the utility will show the UEFI files and their respective information Select the proper UEFI file to update your UEFI and reboot your system after the UEFI update process is completed 34 3 5 Hardware Health Event Monitoring Screen This section allows you to monitor the status of the hardware on your sys tem including the parameters of the CPU temperature motherboard perature fan speed and voltage CPU FAN Setting This allows you to set CPU FAN1 s speed The default value is Full 1 Setting This allows you to set Chassis FAN1 s speed The default value is Full On 35 3 6 This section displays the available devices your system for you to figure the boot settings and the boot priority Boot From Onboard LAN Use this to enable or disable Boot From Onboard LAN Setup Prompt Timeout This shows the number of seconds to wait for the setup activation key Bootup Num Lock If this is set to On it will automatically activate the Nu
13. 6 Mode Use this to enable or disable C6 mode PCB Mode Use this to enable or disable CPB mode Core Leveling Mode Use this to adjust Core Leveling mode 26 3 3 2 Chipset Configuration DRAM Frequency If Auto is selected the motherboard will detect the memory module s inserted and assigns appropriate frequency automati cally UMA Frame Buffer Size Use this to adjust UMA frame buffer size Onboard LVDS Use this to enable or disable onboard LVDS Panel Type Selection Use this to select a panel type Panel BackLight Brightness Use this to select panel backLight brightness HD Audio Azalia Device Select Enabled or Disabled for the HD Audio Azalia Device Front Panel Select Auto or Disabled for the onboard HD Audio Front Panel Onboard LAN 1 This allows you to enable or disable the Onboard LAN 1 Onboard LAN 2 This allows you to enable or disable the Onboard LAN 2 27 Restore AC Power Loss This allows you to set the power state after unexpected AC power loss Power Off is selected the AC power remains off when the power recovers Power is selected the resumes and the system starts to boot up when the power recov ers Good Night LED Enable this option to turn off Power LED when the system is power on The keyboard LED will also be turned off in 1 3 and 4 state The default value is Auto DRAM Voltage Use this to adjust DRAM voltage 28 3 3 3 Storag
14. ASRocK IMB A180 H IMB A180 User Manual Version 1 0 Published April 2013 Copyright 2013 ASRock INC All rights reserved Copyright Notice No part of this manual may be reproduced transcribed transmitted or translated in any language in any form or by any means except duplication of documentation by the purchaser for backup purpose without written consent of ASRock Inc Products and corporate names appearing in this manual may may not be regis tered trademarks or copyrights of their respective companies and are used only for identification or explanation and to the owners benefit without intent to infringe Disclaimer Specifications and information contained in this manual are furnished for informa tional use only and subject to change without notice and should not be constructed as a commitment by ASRock ASRock assumes no responsibility for any errors or omissions that may appear in this manual With respect to the contents of this manual ASRock does not provide warranty of any kind either expressed or implied including but not limited to the implied warran ties or conditions of merchantability or fitness for a particular purpose In no event shall ASRock its directors officers employees or agents be liable for any indirect special incidental or consequential damages including damages for loss of profits loss of business loss of data interruption of business and the like even if ASRock has been adv
15. TPM TPM Header Others 1 7 pin pitch 2 0 wafer connector for LVDS brightness control and audio volume control IMB A180 AMD Debug Header Rea Keyboard Mouse 1 x PS 2 combo PS 2 Serial Port 2 x RS 232 422 485 pin9 with 5V 12V support LAN 2 x RJ45 USB2 0 4 x USB2 0 USB3 0 2 x USB3 0 Display 1 x D Sub VGA IMB A180 1 x HDMI Display 1 x D Sub VGA IMB A180 H 2 x HDMI Audio 2 x Audio Jack MIC in Line Out Operation 0 50 Temperature Storage 20 70 Temperature For detailed product information please visit our website http www asrock com 1 3 Motherboard Layout BLLVOLi 4 SET_cM IMB A180 FE LE Ps2 USB 2 0 Eon 3 Keyboard USBO LP CPU B USB1 II VGA1 COM1 V z ne a lt lt MSATA1 2 LAN USB 3 0 USB2 RJ 45 B USB3 USB 2 0 T USB4 RJ 45 RoHS B USB5 HERES UR S8 898 53132 euncomost SPEAKER LE 1 ooon PCIE1
16. e Configuration OnChip SATA Channel Use this to enable or disable the onchip SATA channel OnChip SATA Type Use this to adjust the onchip SATA type Hard Disk S M A R T Use this to enable or disable S M A R T Self Monitoring Analysis and Reporting Technology 29 3 3 4 Super IO Configuration COM Configuration Use this to set the parameters of COM1 COM2 Configuration Use this to set the parameters of COM2 COM3 Configuration Use this to set the parameters of 4 Configuration Use this to set the parameters of 5 Configuration Use this to set the parameters of COM6 Configuration Use this to set the parameters of COMG LPT1 Port Configuration Use this to set the parameters of the onboard parallel port WDT Timeout Reset This allows users to enable disable the Watch Dog Timer timeout to reset the system The default value is Disabled 30 3 3 5 ACPI Configuration Suspend to RAM Use this to select whether to auto detect or disable Suspend to RAM Select Auto to enable if the OS supports it HPET Timer Use this to enable or disable HPET Timer PS 2 Keyboard Power On Use this to enable or disable the PS 2 keyboard to turn on the sys tem from power soft off mode PCI Devices Power On Use this to enable or disable the PCI devices to turn on the system from power soft off mode RTC Alarm Power On Use this to enable or disable the RTC Real Time Clock to power
17. ects digital identi ties and ensures platform integrity SMB DATA MAIN S_PWRDWN LADI GND This is an interface for the front panel audio cable that allows convenient connec tion and control of audio devices Front Panel Audio Header 9 pin HD_AUDIO1 see p 8 No 30 f 1 High Definition Audio supports Jack Sensing but the panel wire on the chassis must support HDA to function correctly Please follow the instructions in our manual and chassis manual to install your system 2 If you use an AC 97 audio panel please install it to the front panel audio header by the steps below A Connect Mic_IN MIC to MIC2_L B Connect Audio_R RIN to OUT2_R and Audio_L LIN to OUT2_L C Connect Ground GND to Ground GND D MIC_RET and OUT_RET are for HD audio panel only You don t need to connect them for AC 97 audio panel E To activate the front mic For Windows XP XP 64 bit OS Select Mixer Select Recorder Then click FrontMic For Windows 8 8 64 bit 7 7 64 bit Vista Vista 64 bit OS Go to the FrontMic Tab in the Realtek Control panel Adjust Recording Volume 18 System Panel Header 9 pin PANEL1 see p 8 No 22 several system front panel functions HDLED Connect the power switch reset switch and system status indica tor on the chassis to this header according to the pin assignments below Note the positive and n
18. egative pins before connecting the cables PWRBTN Power Switch Connect to the power switch on the chassis front panel You may configure the way to turn off your system using the power switch RESET Reset Switch Connect to the reset switch on the chassis front panel Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart PLED System Power LED Connect to the power status indicator on the chassis front panel The LED is on when the system is operating The LED keeps blinking when the sys tem is in S1 S3 sleep state The LED is off when the system is in S4 sleep state or powered off S5 HDLED Hard Drive Activity LED Connect to the hard drive activity LED on the chassis front panel The LED is on when the hard drive is reading or writing data The front panel design may differ by chassis A front panel mod ule mainly consists of power switch reset switch power LED hard drive activity LED speaker and etc When connecting your chassis front panel module to this header make sure the wire as signments and the pin assign ments are matched correctly 19 This header accommodates CPU Fan Connector 4 pin FAN SPEED 8 N 9 GND FAN_SPEED_CONTROL see p 8 No Chassis Fan Connector 3 pin CHA see p 8 No 21 O GND OT 12V CHA FAN SPEED 3W Audio AMP Output Wafer 4 pin SPEAKER1 Essa see p 8 No 31
19. hat comes with the components 5 When placing screws to secure the motherboard to the chassis please do not over tighten the screws Doing so may damage the motherboard 11 2 1 Installing Memory Modules DIMM This motherboard provides two 204 pin DDR3 Double Data Rate 3 SO DIMM slots Step 1 Unlock a DIMM slot by pressing the retaining clips outward Step 2 Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot The DIMM only fits in one correct orientation It will cause manent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation Step 3 Firmly insert the DIMM into the slot until the retaining clips at both ends fully snap back in place and the DIMM is properly seated 12 2 2 Expansion Slots PCI Express Slots There is 1 PCI Express slot and 1 mini PCI Express slot on this mother board mini PCIE Slot MINI is used for mini PCIE cards PCIE Slot The x4 lane width PCIE1 PCIE 2 0 x4 slot is used for PCI Express expansion cards Installing an Expansion Card Step 1 Before installing an expansion card please make sure that the power supply is switched off or the power cord is unplugged Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation Step 2 Remove the bracket facing the slot that you intend to use Keep the screws for
20. ised of the possibility of such damages arising from any defect or error in the manual or product Fe This device complies with Part 15 of the FCC Rules Operation is subject to the fol lowing two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CALIFORNIA USA ONLY The Lithium battery adopted on this motherboard contains Perchlorate a toxic substance controlled in Perchlorate Best Management Practices BMP regulations passed by the California Legislature When you discard the Lithium battery in Cali fornia USA please follow the related regulations in advance Perchlorate Material special handling may apply see www dtsc ca gov hazardouswaste perchlorate ASRock Website http www asrock com Contents 1 gt a 5 1 1 Package Contents niis 5 1 2 SpecifiCatlotis srin ion 6 1 3 Motherboard Layout sese 8 1 4 3 nnt eee en 10 2 Installations eie nr 11 2 1 Installing Memory Modules DIMM 12 2 2 Expansion Slots PCI Express Slots 13 23 Jumpers Setup inei ai e entire 14 2 4 Onboard Headers and Connectors 16 3 SETUP UTILITY eter 22 3 1 Introductiotn reete sites 22 3 1 1 UEFI Menu treten 22 3 1
21. isplays together one will be true HDMI and one will be in DVI mode and does not support audio Ethernet Dual G LAN 1 x Realtek RTL8111E 1 x Realtek RTL8111DP to support Dash Function Audio ALC662 Two Jacks on Rear 1 0 3W audio amplifier Realtek ALC109 supported with 12 interface to control volume Super NUVOTON NCT6627UD 6 COM ports Expansion Interface 1 x Mini PCIe half size 1x PCIex4 Watch Dog Timer WDT System reset 0 255 interval setting in BIOS Power Mode AT ATX Power on mode supported setting by jumper AT Directly PWR on as Power input ready ATX Press Button to PWR on after Power input ready RTC eKabini embedded a Display LVDS 2 ch 24bits Inverter connector IMB A180 1 HDMI 2 x rear HDMI IMB A180 H Storage 1 x SATAS port 1x mSATA USB 2 x USB2 0 ports by Header 1 x Vertical Type A USB Connector Audio Front Audio Header Buzzer Serial Port 4 x RS232 4 x 1x3 Header to offer PWR select for 2 rear and 2 internal Parallel Port 1 x LPT Header 2x13 K26 2 0mm Digital I O 8 bits Battery Vertical socket FAN 1 x 3 pin FAN with speed control 1 x 4 pin FAN Connector Power In 20 pin ATX PWR connector Front Panel One 2x5 K10 pin Header to offer PWR Button Reset Button PWR Suspend LED HDD LED
22. meric Lock after boot up Full Screen Logo Use this item to enable or disable OEM Logo The default value is Enabled 36 3 7 Security Screen In this section you may set or change the supervisor user password for the system You may also clear the user password Secure Boot menu Use this to enable or disable Secure Boot The default value is Dis abled 37 3 8 Save Changes and Exit When you select this option the following message Save configu ration changes and exit setup will pop out Select OK to save changes and exit the SETUP UTILITY Discard Changes and Exit When you select this option the following message Discard changes and exit setup will pop out Select OK to exit the UEFI SETUP UTILITY without saving any changes Discard Changes When you select this option the following message Discard chang es will pop out Select OK to discard all changes Load UEFI Defaults Load UEFI default values for all options The F9 key can be used for this operation 38 Chapter 4 Software Support 4 1 Install Operating System This motherboard supports various Microsoft Windows operating systems 8 8 64 bit 7 7 64 bit Vista Vista 64 bit XP 64 bit Because motherboard settings and hardware options vary use the setup procedures in this chapter for general reference only Refer your OS documentation for more information 4 2 Support CD Info
23. rmation The Support CD that came with the motherboard contains necessary drivers and useful utilities that enhance the motherboard s features 4 2 1 Running The Support CD To begin using the support CD insert the CD into your CD ROM drive The CD automatically displays the Main Menu if AUTORUN is enabled in your computer If the Main Menu did not appear automatically locate and double click on the file ASSETUP EXE from the BIN folder in the Support CD to dis play the menus 4 2 2 Drivers Menu The Drivers Menu shows the available device s drivers if the system detects installed devices Please install the necessary drivers to activate the devices 4 2 3 Utilities Menu The Utilities Menu shows the application software that the motherboard sup ports Click on a specific item then follow the installation wizard to install it 4 2 4 Contact Information If you need to contact ASRock or want to know more about ASRock you re welcome to visit ASRock s website at http Awww asrock com or you may tact your dealer for further information 39
Download Pdf Manuals
Related Search