The Gardtec Speech Dialler Step by Step User Guide
Contents
1. GARDINER TECHNOLOGY The Gardtec Speech Dialler Step by Step User Guide Introduction The Gardiner Technology Speech Dialler is intended for use as an automatic message dialler The primary use for the dialler is for connection to a security alarm system although the unit is flexible enough to have many other uses where the need for automated messages exists The end user has several programmable options that allow the following To turn the unit On or Off To program delete or change any of the four possible telephone numbers To program delete or change the eleven second common message To program delete or change any of the three short alarm messages To change the user access code To program the number of dial attempts To program the call acknowledge feature The unit is compatible with all makes of alarm control equipment and is capable of up to three different alarm messages if the control equipment has sufficient outputs available Once triggered the dialler will call the first telephone number followed by calls to the other numbers if the call is not answered When the call is answered the common message will be played followed by one of the three alarm messages corresponding to the input triggered If call acknowledge is turned off the dialler will not make any other calls after passing its message lf call acknowledge is turned on an acknowledge signal must be given by the call recipient DT2. Pressing Mo will return to step 2 without updating the User Code Programming Call Acknowledge 1 CO Oo D _ EL Yes 2 l 3 j Yes Display will show 3 etd gt Yes for example This is the current setting for Acknowledge available options are 0 Off No acknowledgement required 1 1 Acknowledgement required 2 2 Acknowledgments required 3 3 Acknowledgments required 4 4 Acknowledgments required 4 I Ki e I Yes F m Enter number required 5 Press __0 J twice to exit from user programming mode Note After any programming please ensure that the display shows Failure to do so may result in unit failing to dial GARDINER TECHNOLOGY Gardiner Technology Ltd reserve the right to change the specification and features of their product without prior notification Gardiner Technology 2001
3. A Guardian is a person who will receive an alarm call from the dialler You must make sure that all Guardians are aware that they may receive a call from your system and agree what action that they should take in the event of them receiving an alarm notification In the case of intruder or PA alarms the Guardian should take adequate steps to ensure his her own safety as the intruder may still be on the premises Direct calls to UK emergency services are not allowed please check for other countries and the facility of programming their number has been blocked If you have programmed the Acknowledgement feature to On please inform the Guardians you have done so With this feature the Guardian MUST have a DIMF Tone type telephone This may be determined by lifting the handset of their telephone and pressing a key if a tone is heard the telephone is DI MF if a clicking sound is heard it is not On receiving a call from the Speech Dialler 1 When the call is answered a series of Granny Tones single blips will be heard for two seconds 2 The Speech Dialler will then pass its Common Message usually address followed by the Short Message usually type of alarm 3 lf Call Acknowledge is off the Speech Dialler will shut down and the Guardian should then take the agreed action Or 4 lf Call Acknowledge is On the Speech Dialler will give a tone after the message has been passed the Guardian should acknowledge this tone by pre
4. MF type telephone required in order to prevent the unit calling other telephone numbers that may have been programmed The unit has a Non Volatile Memory NVM all settings and messages will be retained in the event of a complete power loss Turning the unit On or Off During normal use the display will show hon or a lf the unit is Off no calls will be made if the unit is triggered The method shown below will toggle the unit between On or Off CD COD CDI CED No Note The factory default User Code is 5678 lf the oF display is flashing the unit needs to be programmed with at least one telephone number and a common message Aborting Calls Calls from the dialler may be aborted if the unit has been triggered by accident To Abort a Call Ce CO DCD CE D Provided the unit has not started to play the message the display will show If this display does not show either For three seconds a The unit was not triggered or b The unit had already started to play the message If so the display will show As the Code is entered lf the unit has already passed the message please refer to the next section and check the Last Call Log Viewing Last Call Log With the display showing Press No The display will show the soeech message that was last sent and then the telephone number that it was sent to For example Speech message 1 was sent to Telephone number 2 The display will then
5. ll flash showing Note Mobile telephone numbers may also be used Viewing Telephone Numbers already programmed 1 Cor oF DY ESD a Yes ia 2 l J i Yes 3 7 No Display will scroll the number programmed and then return to step 2 Enter what Tel No you wish to view n 1 to 4 Press j twice to exit programming mode Programming Messages The Speech Dialler may store up to 4 messages these are Common Message Up to 11 seconds Usually the address of the protected premises Short Message 1 Up to 3 seconds Alarm Message for trigger 1 short Message 2 Up to 3 seconds Alarm Message for trigger 2 short Message 3 Up to 3 seconds Alarm Message for trigger 3 Each of the Short Messages correspond to a trigger input on the control equipment for example Short Message 1 would correspond to trigger 1 When the Dialler is triggered from say trigger 1 it would dial the Guardian and then pass the Common Message followed by Short Message 1 or if it was triggered from trigger 2 it would dial the Guardian and then pass the Common Message followed by Short Message 2 To program re program delete the messages 2 2 F p r a 3 ha j a Yes x Enter what Message you wish to program from the list below Choose 9 for Common Message Choose 1 for Short Message 1 Choose 2 for Short Message 2 Choose 3 for Short Message 3 Display will be flashing Note If you wish to delete the e
6. return to its original state If you are viewing the Last Call Log because the unit was triggered by accident you should call the message recipient and inform them of the false call lf the display shows Your previous call was aborted Error Messages shown below is a list of possible error messages that the Speech Dialler is capable of displaying to the end user i N D Q D Cause A bad Checksum error Phase Lock Loop error No Lock error Last call was aborted Call Aborted Telephone Line fault Fail to Speak Alarm Call aborted after message had started to play Action No Action the unit will reboot lf display does not clear call installer No Action the unit will reboot lf display does not clear call installer No Action the unit will reboot lf display does not clear call installer No Action this message will only be seen when viewing the Last Call Log The current call was aborted before the message was passed Correct any problems with telephone line Display will return to normal when no fault is present The unit failed to pass message May be due to line fault as unit was passing message To clear display enter user code or force successful communication Check Last Call Log and contact message recipient Message Cause Action Low Power The voltage to the unit has fallen below 9 5V Call installer Guardian Call Recipient Instructions
7. ssing the key on the telephone for at least one second The tone will be repeated enter the key again The Speech Dialler will now shut down if the acknowledge tone was given or will go on to dial the other Guardians if it was not Speech Dialler Settings The factory default settings are shown below Please enter the settings that you have programmed in to the area provided o n o O e _ ee ee Short Message 3 Unprogrammed Call Acknowledge Guardian List Guardian Associated With Contact Telephone No Guardian 4 Tel No 4 Programming the User Options Programming Telephone Numbers Up to four Guardian recipient telephone numbers may be programmed 1 Lec po DYE Yes ia 2 f J r x 3 P p Yes F el Se Enter what Tel No you i to Display will be flashing O 4 If you wish to delete the existing number press Yes Then return to step 2 or To program re program the number press No E Display will be flashing i g 5 Enter the Guardians Tel No followed by Yes max 16 digits 6 This will return you to step 2 You may then program re program other telephone numbers or press 0 twice to exit programming mode At any point whilst entering the telephone number you may press No This will return you to step 2 without updating the number Note The unit MUST have at least one telephone number programmed otherwise the display wi
8. xisting message press Yes Then return to step 2 or To program re program the message press No _ _ You should now speak your message into the unit at a distance of approximately six inches 15cm away lf your message is shorter than the recording time allowed you may terminate the recording by pressing 0 This will return you to step 2 You may then program re program other telephone numbers or press 0 twice to exit programming mode The unit MUST have at least one Common Message and one Short Message programmed otherwise the display will flash showing Listening to Messages already programmed ODODE aw ia i k Message i 3 hen j gt No gt will play S Enter what Message you wish to listen to from the list below Display will be flashing Choose 9 to play Common Message Choose 1 to play Short Message 1 Choose 2 to play Short Message 2 Choose 3 to play Short Message 3 Or Choose 5 to play Common Message Short Message 1 Choose 6 to play Common Message Short Message 2 Choose 7 to play Common Message Short Message 3 Press _ 0 twice to exit programming mode Note If the Message does not exist the display will show Followed by Changing the User Code 1 Se J O07 Dy a E Yes Display will be flashing 4 Enter your new code followed by Yes This will return you to step 2 5 Press _ j to exit from programming mode
Download Pdf Manuals
Related Search