B2 250 AirTTL User Guide EN
Contents
1. MODE button 4 TESTbutton 11 READY button 5 LCD Display 12 MODEL button 2 6 SYNC button 13 ENERGY SETTINGS dial 1 7 SET button 14 ENERGY SETTINGS dial 2 15 Sync connector 18 Battery charging connector 16 USB port 19 Battery CHECK button 17 Battery 20 Battery release button 21 Group setting 1 26 Battery level indicator 22 Automatic flash exposure indicator TTL 27 Modeling light setting 1 23 Group setting 2 28 Mode setting 24 Light output setting visible only when 29 Ready signal setting lamp head is connected 30 Modeling light setting 2 25 Sync Air setting 31 Temperature limit indicator 32 Lamp head plug 33 Protective glass 34 Umbrella holder 35 Stand attachment screw 37 Clamp screw 36 Tilt lock handle 38 Stand adapter Battery charger 2 8 39 Profoto Battery Charger 2 8A 10 40 Profoto Car Charger 1 8A optional Profoto 41 B2AirTTL Extension Cable 3m optional Operation Quick guide For detailed operating instructions see subsequent sections 1 Charge the battery see page 16 2 Mountthe battery see page 16 3 Removethe protective cap from the B2 lamp head 4 Mountthe B2 lamp head on a traditional light stand or any special equipment see page 16 Connectthe B2 lamp head to the B2 generator see page 17 Switch on the B2 unit by pressing the ON button 8 see page 11 7 Select Sync setting with the SYNC button 62. Sync via cable is possible in all sync modes Connecta sync cable from the camera or flash meter to the Sync Connector 15 Modeling light To turn on off the modeling light on a lamp head press the corresponding MODEL button 9 or 12 The modeling lights are automatically turned off after a settable period of inactivity 1 30 minutes 1 Tosetthetimer press the SET button 7 until SET TIMER is displayed 2 Turn the ENERGY SETTINGS dial 2 14 to change the time Select Freeze Normal mode The B2 unit can operate in two modes to maximize the versatility in different shooting situations e Normal mode Optimized color temperature stability over the entire energy range Best option for most types of shots e Freeze mode Optimized for shortest flash duration Best option for shots where the flash is used to freeze fast action The color temperature might deviate and become slightly bluer The flash duration increases when two lamp heads are used Toggle between Freeze and Normal mode by pressing the MODE button 10 vww profoto com B2 250 AirTTL 14 Select Ready signal The current setting is shown in the Ready signal setting section 29 e The unit beeps when itis ready to flash again after recharging e DIM The modeling light is turned off after flashing and is turned on when the unit is ready to flash again e DIMBEEP The modeling light is turned off after flashing The modeling light is turned
3. brackets Mounting Profoto Light Shaping Tools The built in reflector of the B2 lamp heads creates a wide and even light spread with a high output In addition the B2 lamp heads are compatible with more than 150 light shaping tools which can be used to shape its already beautiful light into almostany light you can imagine All tools with standard reflector mount rubber collar with clasp The Softbox speedring and most reflectors are equipped with Profoto s unique clamp mechanism which makes them easy to mount on the lamp heads 1 Unlockthe clasp on the speedring or external reflector 2 Slidethe speedring or reflector onto the lamp head 3 Secure by locking the clasp on the rubber collar Umbrella mounting Umbrellas are simply mounted by sliding the umbrella shaft into the umbrella holder 34 The diameter ofthe holder is designed for 8 mm shafts 1 Slidethe umbrella shaft into the umbrella holder 34 2 Afterafew centimeters there will be more friction Continue to slide the umbrella shaft afew more centimeters into the umbrella holder 34 Lamp head connection Attention Always remove the protective cap from the lamp head before use With Profoto s lamp head connection heads can be connected and disconnected safely even if the generator is switched on 1 Liftthe protection lid of the lamp head outlet and align the two white square dots on the lamp head plug male with the white dot on the B2 panel 2 Pushthe plu
4. NT 12 vues IRL T 13 Select Freeze Normal 13 SECC add SU la 14 lamo EA MNT 14 14 14 r one 15 Battery status and CNarging ccccsccccsscssssesssesesseeessesesseeeseeesseeesseeeeees 19 Battery mounting nnns 15 Stand mounting esseeeseeeeeeeeneennnnn nnnm nnns 15 Mounting Profoto Light Shaping Tools eeeeeeees 16 Lamp head connection 16 Extension cable connection eeseesseeeeeenennnnnn 17 Replacement of protective glass flash tube modeling light LED 17 f O Y n ei c U n 18 S 18 KU spinenie prin ono r sin len noo 18 Temperature limit indicator 19 Check Firmware eeeeeeeeeeenennnee nnnm nnn nnns 19 Upgrade Firmware UI TIPP UD DU Pe UR UR Ui FED d P IRR 19 Technical data 20 Regulatory information eese rn rernm 22 www profoto com B2 250 AirTTL B2 250 AirTTL www profoto com Nomenclature B2 Profoto Nj 9 OFF 0 1 Lamp head outlet 1 8 ONbutton 2 Lamp head outlet 2 9 MODEL button 1 3 IR Slave eye 10
5. Profoto B2 250 AirTTL This user guide is available in other languages at profoto com support CN thi e hig AS AY H n M profoto com cn support F 2 DE Das Bedienungs Handbuch is auch in anderen Sprachen verf gbar unter profoto com de support ES Esta gu a de usuario est disponible en otros idiomas en profoto com support FR Ce manuel d utilisation est galement disponible en d autres langues sur profoto com fr support IT Questa guida per gli utenti disponibile in altre lingue su profoto com it support JP 200 231 9 3j 4 FI profoto com ja support 24100 Sis C6 RU profoto com ru support e CJProfoto The Light Shaping Company Profoto Air B2 250 AirTTL www profoto com Congratulations on your new Profoto product Regardless if you chose a new flash or anew light shaping tool know that almost half a century s worth of experience was put into its making If the years have taught us one thing it is to never neglect a single detail We only put our name on a product in which we have the fullest confidence Before shipping every one of our products pass an extensive and strict testing program Unless it complies with the specified performance quality and safety itisano go Asaresult we are confident that your new Profoto product will stay with you for years and help you grow as a p
6. ange Ws 1 0 250Ws Energy control increments Dials are progressive turning the dials quickly will result in larger energy change and vice versa Recycling time 0 03 1 35 s Quick burst up to 20 flashes second Modelinglight light LED 9W Equivalent of 50W Halogen Mode control Freeze shortest flash duration or Normal color balanced mode Flash duration Normal mode 10 5 1 9300 s 1 Ws 1 1 000 250Ws 1 15000s 1Ws 1 1 000 s 250Ws Guide number 2 m 100150 with 32 2 10 Magnum reflector Battery Model Exchangeable Li lon battery 451P Type PCA1322 0000 Battery voltage Nominal voltage 14 4 V Charge voltage 16 8 V Battery Energy Capacity 21 6Wh 1 5Ah Battery operating temperature Charge 0 C to 45 C 32 F to 113 F range Discharge 10 C to 50 C 14 F to 122 F Battery capacity Up to 215 full power flashes Battery life 300 charge cycles 80 capacity left Battery status indicator Approx battery level in percentage of the total Capacity is indicated on the display 3 sections 100 70 2 sections 70 40 1 section 40 10 Blinking lt 10 Auto power off Yes after 60 minutes Sleep mode activated 21 after 30 minutes Wireless sync Yes via all Air camera transmitters or IR Slave Allfigures are to be considered as nominal and Profoto reserves the rightto make changes without further notice 1 nr c9 Regulatory information Lithi
7. foto com Temperature limit indicator The temperature limit indicator 31 is litif the B2 has reached a temperature level that has activated the built in over temperature protection When this occurs the performance is limited until the temperature level is back to an acceptable level Note that the battery has a stand alone temperature protection that may be activated without the temperature limit indicator 31 being lit When the battery temperature protection is activated the battery cannot be recharged until cooled down to a safe temperature Check Firmware 1 Press both model light buttons 9 and 12 while turning on the generator 8 2 The current firmware version is shown on the display 5 for example A7 Upgrade Firmware We recommend that you look for firmware upgrades before you start using your new B2 To access the latest free upgrades you create your personal account on profoto com myprofoto Once you have an account you can also choose to register your products and be sure you get noticed when new upgrades are released Upgrade of firmware is made via the USB port 16 on the B2 unit following the instructions provided in the upgrade application downloaded from profoto com myprofoto You can always contact your local dealer or distributor for professional service www profoto com AirTTL LO B2 250 N 20 Technical data Max Energy 200 Ws Energy range f stop 9 f stop 2 0 10 0 1 256 1 1 Energy r
8. g male all the way into the generator socket female 3 Secure by turning the ribbed locking ring on the lamp head plug clockwise Extension cable connection The extension cable is connected in the same manner as the lamp head 1 Firstalign the two white square dots on the lamp head plug male with the dot on the extension connector female 2 Pushthe plug male all the way into the connector female 3 Secure by turning the ribbed locking ring on the lamp head plug clockwise To protect the connectors of the extension cable it is appropriate to connect the plug to the outlet ofthe cable Replacement of protective glass flash tube modeling light LED For replacement ofthe protective glass flash tube or modeling light LED contact your local dealer or distributor for professional service www profoto com B2 250 AirTTL B2 250 AirTTL Other HSS Profoto B2 supports HSS High speed sync if used with any of the optional Air Remote TTL tranceivers currently available for Canon and Nikon HSS enables shooting with flash at a faster shutter speed than the fastest external flash sync speed x sync of the camera This option can be extremely useful to limit the influence of ambient light when shooting in bright conditions HSS is either selected on the remote Canon or in the camera menu Nikon not on the flash In the LCD Display 5 of the B2 a symbol will be visible a couple of seconds after every flas
9. g value 3 Whilethechannelsetting is blinking turn the ENERGY SETTINGS dial 2 14 to change the channel 4 Tochange the group press the SET button 7 until the group settings 21 and 22 are blinking 5 Turnthe corresponding ENERGY SETTINGS dial 13 or 14 to change the group of the lamp head NOTE There are eight different channels 1 8 that can be set and each channel has 6 groups A F All lights set to the same channel will be synced together Groups are used to remotely control individual lights or groups of lights on the same channel when a set up is made with more than one light The TTL function can only be enabled in group A C www profoto com Air Accessories compatible with the B2 For operating instructions refer to the user guide of respective accessory Optional Profoto Usable features in combination with B2 250 AirTTL Air accessory Flashsync Remotecontrol TTL Automatic HSS High flash setting opeed Sync X Air Remote TTL Air Sync Air USB Optional camera mounted transceiver Check Profoto com for TTL supported cameras Optional camera mounted transceiver Dongle for using Profoto Air Software Slave Sync operation When SLAVE is shown in the Sync Air setting section 25 the B2 unit senses the flash release as well as IR signals from most IR sync transmitters To activate slave sync press the SYNC button 6 until SLAVE is displayed Cable Sync operation
10. h when HSS mode is used NOTE During aHSS flash the flash is pulsing to provide a constant light output during the time when the shutter is open To ensure a perfect exposure and a stable flash pulse the B2 uses only the upper part of its power range when in HSS Mode Frequent use of HSS will have an impact on the life time of the B2 flash tube Your Air Remote TTL may require a firmware update in order to use the HSS feature The lastest updates and a list of compatible cameras is available on profoto com myprofoto Create your personal account and login to access all new upgrades TTL Profoto B2 supports TTL when used with any of the optional Air Remote TTL tranceivers currently available for Canon and Nikon With a TTL remote mounted in the camera hotshoe you may select to let the camera control the flash output fully automatically without manual metering TTL is selected on the remote not on the flash If the camera requires a flash output outside the range of the B2 the B2 will blink the energy setting on the LCD Display b and produce a long beep to indicate this it will only beep if the ready signal is turned on The automatic flash exposure indicator 22 AUTO is lit every time the flash output is set automatically by the camera The indicator is litforten seconds after receiving a TTL flash command from the remote Find more info on the optional TTL remotes and a list of compatible cameras on Profoto com www pro
11. hotographer But getting the product is only the beginning of that journey Using it for light shaping is the real adventure That is why we take pride in providing you with such a wide assortment of light shaping tools allowing you to shape the light in any way you can imagine Thealmost infinite possibilities might seem bewildering at first but we re certain you will soon getthe hang of it Still encourage you to sign up for our newsletter at www profoto com newsletter or visit our blog at www profoto com blog sothat we can share our experience from almost 50 years of light shaping and hopefully inspire you to grow even further Enjoy your Profoto product Conny Dufgran founder OKO f Ta n WWW pDrototo com B2 250 AirTTL General safety instructions X SAFETY PRECAUTIONS Do not operate the eguipment before studying the instruction manual and the accompanying safety Make sure that Profoto Safety Instructions is always accompanied the eguipment Profoto products are intended for professional use Generator lamp heads and accessories are only intended for indoor photographic use Do not place or use the eguipment where it can be exposed to moisture extreme electromagnetic fields or in areas with flammable gases or dust Do not expose the equipmentto dripping or splashing Do not place any objects filled with liquids such as vases on or near the equipment Do not expose the equipment to hasty tempe
12. on and the unit beeps when it is ready to flash again e Blank No ready signal To select the ready signal setting press the READY button 1 1 The TEST button 4 is always turned off after flashing and is illuminated when the B2 is ready to flash again Turn On Off lamp head To turn off the lamp head press the corresponding MODEL button 9 or 12 for one second The lamp head s light output setting 24 will show when the lamp head is turned off To turn on the lamp head press the MODEL button once more Wrong exposure alarm If a flash is released before the unit is ready there will be a long beep and the display will blink These signals indicate that the flash light does not fully correspond to the set value The B2 will always flash even if the set light output cannot be met as the image may still be usable ifthe catch ofthe moment was perfect Note that the sound alarm only will be activated when the Ready signal is set to or DIM BEEP Quick burst Quick burst is an automatically activated function that allows a series burst of flashes to be fired ata faster pace than the B2 can recharge without losing light output The function is only active when the light output is setto less than full The length of the burst in number of flashes depends on the repetition rate and the set light output The lower the light output is set the more bursts can be triggered Thanks to this feature the B2 can t
13. ote TTL Air Remote orAir USB www profoto com 50 AirTTL LO N N ea B2 250 AirTTL The TEST button 4 is illuminated when the B2 is fully charged and ready to flash To release atest flash press the TEST button 4 Note that the flash light output is set automatically when shooting in TTL mode with the optional Air Remote TTL Select Sync setting The current sync setting is shown in the Sync Air setting section 25 on the display Wireless sync settings e AIR The built in Profoto Air transceiver is activated The B2 is set to be triggered and or controlled from any of the optional Profoto Air transceivers offered by Profoto e SLAVE The built in IR Slave eye 3 is activated The flash will slave sync if another flash is fired or if an IR signal is detected Cable sync only e Blank When the Sync Air setting section 25 is blank the B2 can only be synced via acable To select sync setting press the SYNC button 6 Air and TTL operation When AIR is shown in the Sync Air setting section 25 the B2 is setto be triggered and or controlled from any of the optional Profoto Air transceivers offered by Profoto The B2 supports all available Air accessories offered by Profoto including those listed in the table below 1 Activate Air by pressing the SYNC button 6 until AIR is displayed 2 Toviewthecurrentchannel setting press the SET button 7 once The channel setting is displayed with a blinkin
14. perature protection When the battery temperature protection is activated the battery cannotbe recharged until cooled down to a safe temperature Battery mounting 1 To mount the battery fit the battery pack in place and push firmly until the battery pack locks in place Make sure there is a click sound indicating that the battery pack is properly secured 2 Todismountthe battery first switch off the B2 unit Remove the bag press the battery release button 20 and pull out the battery pack Stand mounting The B2 lamp heads can be mounted on a traditional light stand using the supplied stand attachment As an alternative the stand attachment can be removed and the lamp head can be mounted on a special grip or stand a camera flash bracket or other special equipment for more convenient use Mounting on a traditional light stand 1 Fitthe stand adapter 38 to a light stand and secure it with the clamp screw 37 2 Thelamp head can be directed upwards downwards when the tilt lock handle 36 is loosened Fasten the tilt lock handle 36 when the lamp head is correctly directed www profoto com B2 250 AirTTL B2 250 AirTTL Mounting on a special stand grip or camera flash bracket 1 Unscrew the stand attachment screw 35 and remove the stand attachment 2 Thread the lamp head onto the special equipment Note that the thread size of the B2 lamp head is 3 8 and that a 1 4 thread insert may be needed for some grips and
15. quipment Overheating Risk Remove transport cap from lamp head before use Do not obstruct ventilation by placing filters diffusing materials etc over inlets and outlets of the equipment ventilation or directly over glass cover modeling lamp or flash tube Note about RF This equipment makes use of the radio spectrum and emits radio frequency energy Proper care should be taken when the device is integrated in systems Make sure that all specifications within this document are followed especially those concerning operating temperature and supply voltage range Make sure the device is operated according to local regulations The frequency spectrum this device is using is shared with other users Interference cannot be ruled out Final Disposal Equipment contains electrical and electronic components that could be harmful to the environment Equipment may be returned to Profoto distributors free of charge for recycling according to WEEE Follow local legal requirements for separate disposal of waste for instance WEEE directive for electrical and electronic equipment on the European market when product life has ended www profoto com Table of Contents General safety 4 en 7 ODOT U Cata i mcm 11 AUE A ON 11 PONBPOU 11 Set light output in manual mode Energy level 11 gt ME
16. rature changes in humid conditions as this could lead to condensation water in the unit Do not connect this equipment to flash equipment from other brands Glass cover shall be changed if become visibly damaged to such an extent that its effectiveness impaired for example by cracks or deep scratches If unit is broken it should be sent to authorized service station WARNING Electrical Shock High Voltage Mains powered generators shall always be connected to a mains socket outlet with a protective earthing connection Only use Profoto extension cables Do not open or disassemble generators or lamp heads Equipment operates with high voltage Generator capacitors are electrically charged for a considerable length of time after being turned off The disconnect device shall remain readily operable Batteries battery pack or batteries installed shall not be exposed to excessive heat such as direct sunlight fire or the like Safety advices for Lithium lon batteries Do not crush Do not heat or incinerate Do not short circuit Do not dismantle Do not immerse in any liquid as this may cause the battery to ventor rupture Caution Burn Hazard Hot Parts Do not touch hot parts with bare fingers Modeling lamps flash tubes protective glass and certain metal parts emit strong heat when used Do not point modeling lamps or flash tubes too close to persons All lamps may on rare occasions explode and throw out hot particles NOTICE E
17. rigger several flashes on lower power output without triggering the Wrong exposure alarm Note that the accuracy of the light output is slightly less precise when Quick burst is active Quick burstis indicated by blinking energy settings www profoto com Handling Battery status and charging The battery status is indicated by the battery level indicator 26 onthe display The battery status can also be checked by pressing the CHECK button 19 on the battery pack See also section Technical data For optimal performance the battery should be fully charged prior to usage The battery can be charged while in use and from any charge level Only use the Profoto Battery Charger 2 8A or the Profoto Car Charger 1 8A Do notusethe Profoto Battery Charger 4 5A as it may decrease the battery lifetime Ifthe battery has not been used for a long time the Profoto Battery Charger 2 8A should be used The Profoto Car Charger 1 8A should not be used in this case 1 Connectthebattery charger to the battery charging connector 18 onthe battery pack 2 Checkthatthe battery charger indicates that charging is in progress 3 Whenthe battery charger indicates thatthe charging is completed itis recommended to disconnectthe battery charger from mains power and from the battery pack For increased battery lifetime do not leave the battery uncharged for a long time NOTE To ensure a long battery lifetime the battery is designed with a built in overtem
18. see page 12 When using the wireless Air setting make sure to setthe same channel on both generator and remote control 8 Set the flash light output of the connected lamp head with the corresponding ENERGY SETTINGS dial 13 or 14 see page 11 Note that the flash light output is set automatically when the TTL function is used 9 Releaseatestflash by pressing the TEST button 4 see page 7 10 Turn on off the modeling light of the connected lamp head by the corresponding MODEL button 9 or 12 see page 13 11 SelectFreeze Normal mode by pressing the MODE button 10 see page 13 12 Select Ready signal setting with the READY button 11 see page 14 13 Mount Light Shaping Tools see page 17 gt o Power on off To switch on off the B2 unit press and hold the ON button 8 for 1 second When the B2 unit is switched off the current settings are stored and will apply when the unit is switched on again The B2 unit automatically goes into sleep mode after 30 minutes and shuts off completely after one hour of inactivity to save battery life Setlight output in manual mode Energy level The output of the flash light is shown in a relative f stop scale in the light output setting section 24 on the display The maximum energy 250 Ws is shown as 10 0 To change the energy level of the connected flash light use the corresponding ENERGY SETTINGS dial 13 or 14 The setting can also be done on the optional Air Rem
19. tion number only signifies that the Industry Canada technical specifications were met Les lettres IC n ont aucune autre signification ni aucun autre but que d identifier ce qui suit comme le num ro de certification d enregistrement d Industrie Canada Profoto AB Transmitter Receiver MODEL Profoto B2 250 AirTTL 2 4 GHz PRODUCT NO PCA1325 0000 Contains FCC ID W4G RMI and IC 8167A RMI Made in Sweden IANANAI Arafata NAM W N W p Japan The module has been granted modular approval for sale and operation in Japan EXE SER OREH Classification of specified radio equipment Article 2 Clause 1 Item 19 2 4 GHz Wide Band Low Power Data Communication EHO E4350 BWER 38402498 UBRO EICHO lt OCHSCERET This is to certify that the above mentioned certification by type has been granted in accordance with the provisions of Article 38 24 Paragraph 1 of the Radio Law 202WW08109201 E www profoto com B2 250 AirTTL 23 Technical data and product information are subject to change without notice Profoto AB P O Box 1264 SE 172 65 Sundbyberg SWEDEN Visiting address Landsvagen 57 Sundbyberg Phone 46 8 447 53 00 info profoto com www profoto com 9 C Profoto Profoto Air The Light Shaping Company
20. um lon battery The Lithium lon battery is approved for air transport under UN 3480 3481 World wide Usage of Radio Spectrum The Profoto Air system operates on the license free 2 4GHz ISM band for SRD Short Range Devices This band may be used in most parts of the world Regional restrictions may apply NOTE Refer to national regulations for the region where the Profoto Air Sync or Profoto Air Remote transceiver shall be operated and make sure that they are followed Unites States and Canada F C C and Industry Canada Compliance Statement Part 15 19 This device complies with Part 15 of FCC rules and RSS 210 of Industry Canada Operation is subjectto the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Warning Part 15 21 Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Ce dispositif est conforme aux normes RSS 210 d Industrie Canada L utilisation de ce dispositif est autoris e seulement aux conditions suivantes 1 ilnedoitpas produire de brouillage et 2 l utilisateur du dispositif doit tre pr t accepter tout brouillage radio lectrique recu m me si ce brouillage est susceptible de compromettre le fonctionnement du dispositif The term IC before the certification registra
Download Pdf Manuals
Related Search