User Guide
Contents
1. Press the MENU button up to when the Loo is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the c Led on or 8 FIF Led off mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again 10E It Display Inversion It is good for you to install the unit on the floor or under ceiling Press the MENU button up to when the 5 2r is blinking on the display Use the ENTER button to change to the mode J Z oar i display inversion It will automatically store after 8 seconds Or press the ENTER button again return to the mode dar display normal To go back to the functions press the MENU button Dar Display normal mode for the fixture putting on the floor dior Display inversion mode for the fixture fixing under ceiling l I Focus Adjust Press the MENU button up to when the is blinking on the display Pressing ENTER button the unit will focus on tilt 90 and then the unit will focus on tilt 0 pan 0 pan 90 pan 180 pan 270 in every pressing ENTER button To go back to the functions press the MENU button again I tol Self Test Press the MENU2. LA onm J Tr Lin r LL mm J c e n FRdu Focus Adjust EPS5E Self Test IP Ambient temperature of lamp C Fixture Hours np an Lamp on aor FE Lamp off L r1 T q SPE Reset VIII DMX512 Address Setting Press the MENU button up to when the 2r js shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to change the DMX512 address Once the address has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again 8E Channel Mode Press the MENU button up to when the Lhiid is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the inn 16 Channel or OLA 8 Channel mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again l1 l RININ Show Mode Press the MENU button up to when the nid is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the 3n show 1 or 9n c show 2
3. 13E 5 How To Control The Unit You can operate the unit in three ways 1 By master slave built in preprogrammed function 2 By easy controller 3 By IL 0824 only for setting in 8 channel mode please refer to the user guide of iLead controller or by universal DMX controller No need to turn the unit off when you change the DMX address as new DMX address setting will be effected at once Every time you turn the unit on it will show 1250 on the display and move all the motors to their home position and you may hear some noises for about 20 seconds After that the unit will be ready to receive DMX signal or run the built in programs 5 1 Master Slave Built In Preprogrammed Function L u Lo T LL You can select blackout mode HL jn 2 IL yes blackout or 0 CC no blackout mode while the unit is turned on By linking the units in master slave connection the first unit will control the other units to give an automatic sound activated synchronized light show This function is good when you want an instant show You have to select show show 1 2 3 4 modes by easy controller Its DMX input jack will have nothing plugged into it and Its master LED will be constantly on and sound LED will flash to the music The other units will have to set in slave mode Suna and select normal or 2 light show mode Their DMX cables plugged into the DMX input jacks daisy chain and the slave LED lights
4. MENU To select the programming functions DOWN To go backward in the selected functions To go forward in the selected functions ENTER To confirm the selected functions Remote controller input By connecting to the 1 4 microphone jack to control the unit for Stand by Function and Mode function Sensitivity To adjust the sound input sensitivity DMX input output For DMX512 operation use 3 pin XLR plug cable to link the unit together 7E 4 2 Main Function To select any of the pre set functions press the MENU button up to when the required one is shown on the display Select the function by ENTER button and the display will blink Use DOWN and UP button to change the mode Once the required mode has been selected press the ENTER buiton to setup or it will automatically return to the main functions without any change after idling 8 seconds To go back to the functions without any change press the MENU button The main functions are shown below DMX512 Address Setting OL OL 1 aie Lr ni amp Lh Setting 16 Channel Ln Setting 8 Channel Show mode 1 Show mode 2 Show mode 3 Show mode 4 Slave Mode Normal Slave mode 2 Light Show Blackout Mode Yes Blackout Blackout Mode No Blackout na Pan Normal i Pan Inversion morc 2a Tilt Normal MENU eee i Tilt Inversion an LED on Tt Fr LED off Cm i Display Normal RE Display Inversion NN i 3l lit a co rl
5. d is shown on the display Pressing ENTER OO ye S Press the MENU button up to when the button and the display will blink Use DOWN and UP button to select the blackout or no no blackout mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU buiton again l LI pan Inversion Press the MENU button up to when the i Cin is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the 0 amp 2 normal or pan inversion mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again La L LLL Tilt Inversion Press the MENU button up to when the ELE is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the 2 normal or tilt inversion mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again Li Led Display
6. EN61000 4 3 2002 EN61000 4 4 1995 EN61000 4 5 1995 EN61000 4 6 1996 EN61000 4 11 1994 amp Harmonized Standard EN 60598 1 2004 IEC 60598 1 2003 4 corrigendum 2004 Part 1 General requirements and test Following the provisions of the low voltage directive 73 23 EEC and 93 68 EEC Innovation Quality Performance 23E
7. damaged Do not look directly at the light while the bulb is on Caution There are no user serviceable parts inside the unit Do not open the housing or attempt any repairs by yourself In the unlikely event your unit may require service please contact your nearest dealer Installation The unit should be mounted via its mounting system as shown below on the bottom of the base Use clamps to fix the unit to truss Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 30 kgs for each unit Safety chain quu di Ld cr TaT IL ony fr ind ILU UTER t i 3E Power supply AC 120V 60Hz or AC 230 240 250V 50 60Hz Lamp MSD 250W NSD 250 2 W IM 250S NSD 400W IM 400S Optical system High efficiency optical system High quality optical lens and dichroic colors Beam angle 13 Shutter Dimmer Blackout 0 100 smooth dimming and strobe speed variable 1 10 flashes per second Color wheel Independent color wheel with 9 trapezoid dichroic colors plus white Color wheel rotates with variable speed giving rainbow effect Gobo wheel Independent gobo wheel with 7 rotating interchangeable gobos plus open 5 metal gobos 2 glass gobos are included Gobo wheel rotates with variable speed giving shaking effect Effect Wheel Prism
8. Rotating Prism Movement Pan 540 in 2 8 second Tilt 270 in 1 6 second DMX Channels Standard DMX 512 signal addressing and can be controlled by any universal DMX controller 16 Channels Channel 1 2 Pan Channel 9 Gobo Channel 2 Tilt Channel 10 2 Gobo Rotation Channel 3 Pan Tilt Speed selection Channel 11 Prism Channel 4 Dimmer Channel 12 Prism Rotation Channel 5 Shutter Shaking Channel 13 Focus Channel 6 Color Channel 14 Pan 16 bit Channel 7 No Function Channel 15 Tilt 16 bit Channel 8 No Function Channel 16 Reset Lamp on off 4E 8 Channels Luminous intensity Channel 1 Pan Channel 2 Tilt Channel 3 Shutter IM 250S 14480 4500 1900 lux Channel 4 Gobo Channel 5 Color Channel 6 Gobo Rotation Channel 7 Prism Prism 16500 4400 2080 lux Rotation Dimmer Channel 8 Focus Distance m Dimension 428 x 371 x 466 mm L x W x H Weight 23 kg IM 2505 27 kg IM 400S 2 1 Inserting Exchanging rotating gobos DANGER Install the gobos with the device switched off only Unplug from mains before changing gobos Open the cover by loosening the fastening screw at the sides of the cover If you wish to use other forms and patterns as the standard gobos or if the gobos are to be exchanged remove the fixation ring with an appropriate tool Remove the gobo and insert CAUTION Never unscrew the screws of the rotating gobo
9. as the ball bearing will otherwise be opened SE 1 In case of replacement of the lamp or maintenance do not open the fixture within 15 minutes until the unit cools down after switching off WARNING Because of its high internal pressure there might be a risk that the Discharge lamp would explode during operation The lamp emits intense UV radiation which is harmful to the eyes and skin The high luminance of the arc can cause severe damage to the retina if looks directly at the lamp MSD 250W NSD 250 2 W IM 250S NSD 400W IM 4005 1 Always switch off the main supply and never handle the lamp or luminaire when it is hot 2 Do not touch the bulb with bare hands If this happens clean the lamp with denatured alcohol and wipe it with a lint free cloth before installation 3 The lamp generates UV radiation Never operate the lamp without appropriate shielding 4 When burning the lamp operates at high pressure and there is a slight risk of arc tube rupture The risk increases with age temperature and improper handling of the lamp Do not use the lamp any longer than its specified life 5 Make sure the lamp is located in the center of the reflector for the best spot 6E 4 How To Set The Unit 4 1 Control Panel DMX OUT SENSITIVITY ONLY FOR REMOTE CONTROL Display To show the various menus and the selected functions LED DMX input present masten on marmo SUME on swem Button
10. in stand alone programs 5 3 2 DMX Controller If you use a universal DMX controller to control the units you have to set DMX address from 1 to 512 channel so that the units can receive DMX signal Press the MENU button up to when the addr is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to change the DMX512 address Once the address has been selected press and keep ENTER button pressed up to when the display stops blinking or storing automatically 8 seconds later To go back to the functions without any change press the MENU button again Please refer to the following diagram to address your DMX512 channel for the first 4 units You have to set the fixture DMX address in 8 channels mode when you use 1L 0824 controller DMX address can be set remotely by IL 0824 controller No need to calculate the DMX channels of each fixture in the chain Please refer to the following diagram to address your DMX512 channel for the first 4 units sa 15E 5 4 DMX 512 Configuration 8 Channels DMX 512 Configuration Channel 1 Channel Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 Channel B Prism Prism rotation Tilt Shutter Shakin Gobo Calar Gobo rotation Facus 16 Channels DMX 512 Configuration om Dom ECHEEECHNETT EN aua uas n oe a eas D een l Pan Tilt speed select mme Snuer Snaking noo fj x c 255 100 248 255 Open 24B 25
11. o r 3n 3 show 3 o r an d show 4 mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again Show 1 mode Fixture is placed on the floor Tilt movement angle 210 Show 2 mode Fixture is fixed under ceiling Tilt movement angle 90 Show 3 mode Fixture is placed on the speaker The spot is always projecting to the audience s direction i e in front of the stage Pan movement angle left to right to left 160 Tilt movement angle 90 60 above horizon 30 below horizon Show 4 mode Fixture is fixed under ceiling The spot is mainly projecting in front of the stage Pan movement angle left to right to left 160 Tilt movement angle 90 vertically front 75 back 15 C1 n9 J L Slave Mode Press the MENU button up to when the Liig is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the normal or 2 light show mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again 9E L l LIU 110 Blackout Mode
12. or servicing Replace fuse lamp only with the same type Make sure there are no flammable materials close to the unit while operating as it is fire hazard Use safety chain when fixes this unit Don t handle the unit by taking its head only but always by taking its base Maximum ambient temperature is Ta 40 C Don t operate it where the temperature is higher than this Unit surface temperature may reach up to 85 C Don t touch the housing bare hand during its operation and allow about 15 minutes to cool down before replacing bulb or serving as the unit could be very hot In the event of serious operating problem stop using the unit immediately Never try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center Always use the same type spare parts Don t connect the device to any dimmer pack Do not touch any wire during operation as there might be a hazard of electric shock 2E Warning To prevent or reduce the risk of electrical shock or fire do not expose the unit to rain or moisture Never touch bulb with bare fingers as it is very hot after using e Hotlamp explosion hazard Do not open the unit within five minutes after switching off Do not start on the unit without bulb enclosure or when housing is damaged The housing the lenses or the ultraviolet filter must be replaced if they are visibly
13. 0 ohm 1 4W between pin2 DMX and l M pin3 DMX of the last fixture cause damage or interference to DMX interface circuit 1 If you use a controller with 5 pins DMX connector you need to use a 5 to 3 pin adapter C Some units don t respond to the easy controller 2 Atlast unit the DMX cable has to be terminated with a terminator Solder a 120 ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pin XLR plug and plug it in the DMX output of the last unit 3 Connect the unit together in a daisy chain by XLR plug cable from the output of the You may have a break in the DMX cabling Check the LED for the response of the master slave mode signal m Wrong DMX address in the unit Set the proper address UO Nor n h n unit to the input of the next unit The cable cannot be branched or split to a Y cable PIospousototismoume DMX512 is a very high speed signal Inadequate or damaged cables soldered joints or Make sure the unit is not receiving DMX signal corroded connectors can easily distort the signal and shut down the system 2 Check microphone to see if it is good by tapping the microphone 4 The DMX output and input connectors are pass through to maintain the DMX circuit E One of the channels is not working well when power is disconnected to the unit 1 The stepper motor might be damaged or the cable connected to the PCB is broken 5 Each lighting unit needs to have an address set to rec
14. 5 H an E T m 240 247 H 247 si P zm TER 239 Fast shaking i LT 7 N pi l 239 Fast shaking tee j Ia NK p i 2 Slow T TET 132 Slow shaking d IF 7 115 127 Fink 112 127 d lt 131 Fast shutter 102 114 Light green e F 1 a LU d cm om D k i pan HHN DBB5 101 UV purple M s ac Y UM E a 17 XR o gt 077 088 Blue x m NEU w 086 111 27 LE a 64 076 Red ial 115 127 Pink il I g F 1 18 Slowshutter 051 063 Yellow 7 ARM 132 Slow shaking PU oats Pee Pa 1 20 082 1 F mi N bda 121 134 Stopped ram eiect z e 2 M d Mitis 035 050 Light blue siar o 5 102 114 Light green i S Gl E EET E n os SPAN 1026 038 Magenta ud S dus EC l 103 Slow m ast D 000 007 Blackout 013 025 Green 088 101 UV purple j 000 E 131 Fast shutter i O12 White SM Prism effect 2 Channel 8 Channel 10 Channel 11 Channel 12 Channel 13 Channel 14 Channel 15 Channel 16 077 088 Blue 040 Fasi 048 063 e 051 063 Yellow NK 039 050 Light blue 15 Slow shifter 026 038 Magenta 910 08 015 Open 013 025 Green ODO OD7 Blackout 0 000 012 White G00 009 Stopped 080 095 1 Prism elfect 1 son 064 079 z 0E5111 1 121 134 Stepped 085 170 048 053 e O 032 047 EF Djs 018 034 8 010 Fast 010 Fast 000 015 C 000 009 Stopped 000 085 Open 000 008 Stopped 16 BIT PAN 16 BIT TILT Gobo3 Gobo4 i For DMX reset put DMX value of CH 8 amp CH 16 to 255 the unit will reset after about five
15. Set DMX value of channel 8 and channel 16 to 255 then all channels of the unit will return to their standard home position 4 3 Home Position Adjustment Press MENU button for at least 5 seconds into offset mode to adjust the home position when you want to adjust pan and tilt home position you should be run ric mode first the functions are shown below a Focus Adjust 0 255 n pan HaPRH Pan offset 0 512 n MENU oF EH Tilt offset 0 2048 Focus Adjust Press the MENU button for at least 5 seconds into offset mode use DOWN and UP button up to when the ea L is shown on the display Pressing ENTER button the unit will focus on the center position Use DOWN and UP button to adjust focus this settings only for offset mode to adjust home position To go back to the main functions without any change after 8 seconds 12E VII Pan offset Press the MENU button for at least 5 seconds into offset mode use DOWN and UP button up to when the C NM is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to adjust the pan home position Once the position has been selected press the ENTER button to setup or automatically return to the offset functions without any change press the MENU button again To go back to the main functions without any change after 8 seconds LL Li L Tilt offset Press the MENU button for a
16. Z Solution Your integrated Solution TABLE OF CONTENTS LINKABLE RON CNN STAND ALONE SFZ 1 Safety Instruction 2 Technical Specification 3 Lamp 4 How To Set The Unit 4 1 Control Panel 4 2 Main Function 4 3 Home Position Adjustment 5 How To Control The Unit 5 1 Master Slave Built In Preprogrammed Function 5 2 Easy Controller 5 3 iSolution Operation DMX Controller 5 4 DMX 512 Configuration 5 5 DMX 512 Connection 6 Troubleshooting 7 Fixture Cleaning User Guide Please read these instructions carefully before use 1E 1 Safety Instruction A WARNING Please read carefully the instruction which includes important information about the installation usage and maintenance Please keep this User Guide for future consultation If you sell the unit to another user be sure that they also receive this instruction booklet Unpack and check carefully there is no transportation damage before using the unit Before operating ensure that the voltage and frequency of power supply match the power requirements of the unit Its important to ground the yellow green conductor to earth in order to avoid electric shock The unit is for indoor use only Use only in a dry location The unit must be installed in a location with adequate ventilation at least 50cm from adjacent surfaces Be sure that no ventilation slots are blocked Disconnect main power before fuse lamp replacement
17. button up to when the c PE is blinking on the display Pressing ENTER button and the unit will run self test by built in program To go back to the functions press the MENU button again Ambient temperature of lamp dj Press the MENU button up to when the C is blinking on the display Pressing ENTER button and the ambient temperature of lamp will show on the display To go back to the functions press the MENU button again l Fixture Hours Press the MENU button up to when the Fine 5 is blinking on the display Pressing ENTER button and the display will show the number of working hours of the unit To go back to the functions press the MENU button again 11E Lamp ON OFF Press the MENU buiton up to when the L button and the display will blink Use DOWN and UP button to select the G Lamp on is blinking on the display Pressing ENTER or art Lamp off mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again ICE Reset Press the MENU button up to when the See is blinking on the display Pressing ENTER button and all channels of the unit will return to their standard position To go back to the functions press the MENU button again DMX RESET
18. eive the data sent by the The motors drive IC onde BOB might ba outotcondition controller The address number is between 0 511 usually O amp 1 are equal to 1 2 F The lamp is cutting out intermittently The end of the DMX512 system should be terminated to reduce signal errors The lamp is not working well Check the main voltage either too high or too low Internal temperature may be too high Check and if necessary replace the fan on the head 3 pin XLR connectors are more popular than 5 pins XLR 3 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 5 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal N 18E 19E G If The pan belt is broken F If The tilt belt is broken 1 Turn off the main power 1 Turn off the main power 2 Unscrew all the screws A and open the base housing cover B 2 Unscrew all the screws A and open the right arm cover B 3 Unscrew all the screws C and open the arm cover D 3 Unscrew the screws C the screws D and screws E that fix the bridge 4 Unplug all the connect wires that from the arm to the bottom 4 Change a new belt F Please adjust the tension of the belt properly Note do not fix 5 Unscrew the screws E and remove the fixture head belt too tight as it is easy to rupture 6 Loose the screws F then loose the screws C 5 Reverse the procedures from point 3 to 2 7 Change a new belt H put the belt aro
19. seconds For lamp on put DMX value of CH 8 to 247 amp CH 16 to 255 For lamp off put DMX value of CH 8 to 239 amp CH 16 to 255 ii For color sound activated put DMX value of CH 6 to 248 255 For gobo sound activated put DMX value of CH 9 to 248 255 16E 17E 5 5 DMX512 Connection 6 Troubleshootino The DMX512 is widely used in intelligent lighting control with a maximum of 512 Following are a few common problems that may occur during operation Here are some suggestions for easy troubleshooting channels 1 2 3 4 A The unit does not work no light and the fan does not work s 1 Check the connect power and main fuse I eus E FI as 2 Measure the mains voltage on the main connector XN 3 Check the power on LED o ene B Not responding to DMX controller 1 DMX LED should be on If not check DMX connectors cables to see if link properly 2 Ifthe DMX LED is on and no response to the channel check the address settings and DMX polarity DMxX512 COMMON 120 ohm 1 4WW f 3 Ifyou have intermittent DMX signal problems check the pins on connectors or on PCB of INPUT OUTPUT the unit or the previous one Termination reduces signal errors and to avoid signal 4 Try to use another DMX controller t issi bl d interfei Itis al sableain ta Connects DMX eei RERS 5 Check to see if the DMX cables run near or run alongside to high voltage cables that may Resistance 12
20. t least 5 seconds into offset mode use DOWN and UP button up to when the OC El is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to adjust the tilt home position Once the position has been selected press the ENTER button to setup or automatically return to the offset functions without any change press the MENU button again To go back to the main functions without any change after 8 seconds Gobo offset Press the MENU button for at least 5 seconds into offset mode use DOWN and UP button up to when the iiobis shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to adjust the gobo home position Once the gobo has been selected press the ENTER button to setup or automatically return to the offset functions without any change press the MENU button again To go back to the main functions without any change after 8 seconds EA LI LL Color offset Press the MENU button for at least 5 seconds into offset mode use DOWN and UP button up to when the LOL is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to adjust the color home position Once the color has been selected press the ENTER button to setup or automatically return to the offset functions without any change press the MENU button again To go back to the main functions without any change after 8 seconds
21. und the axis gear and motor gear D T 8 Screwed the screws G install the new belt and adjust the belt tension properly Note do not fix belt too tight as it is easy to rupture 9 Plug all the connect wires back that form the bottom to the arm 10 Reverse the procedures from point 5 to point 2 20E 21E Pay attention to the belt tension when install the belt Please refer to the photos below Te ll a A ji H LI Ui 5 f A Y Photo 1 Adjust belt tension through loose the screw Photo 2 22E T Fixture Cleaninc The cleaning of internal and external optical lenses and or mirrors must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit s optics Clean with soft cloth using normal glass cleaning fluid Always dry the parts carefully Clean the external optics at least every 20 days Clean the internal optics at least every 30 60 days EC Declaration of Conformity We declare that our products lighting equipments comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility EMC Directive 89 336 EEC EN5501 4 2 1997 A1 2001 EN61000 4 2 1995
22. will constantly on 2 light show In SL ud slave mode means the unit works normally and means 2 light show In order to create a great light show you can set on the second unit to get contrast movement to each other even if you have two units only 5 2 Easy Controller The easy remote control is used only in master slave mode By connecting to the 1 4 microphone jack of the first unit you will find that the remote control on the first unit will control all the other units for Stand by Function and Mode Velia Zarini Controller 14E Stand by Blackout the unit Strobe X Y moving show pattern Gobo Color selection X Y moving setting 1 Color sync strobe selection 1 Hold on for gobo 1 Pan position 2 Sync strobe Show 1 Show 4 selection 2 Tilt position Function 3 Two light strobe Please refer to 4 2 Main 2 Press for color change 3 Dimmer Functions Show mode First set Master unit then set Slave units position Mode Sound 1 Sound 2 Slow Sound 3 Position Latch LED off LED slow blinking LED on LED fast blinking 5 3 1 iSolution Operation Consistent DMX configuration enable iMove to be linked with iRock and iShow together and controlled at the same time DMX address can be set remotely by iLead controller please refer to the user manual of iLead controller No need to calculate the DMX channels of each fixture in the chain e Automatic switching between DMX function and built
Download Pdf Manuals
Related Search