Installation and User Guide Mira Magna Water
Contents
1. Adjuster Ring BIR 464 08 464 23 Temperature Knob User Interface S NS m 452 10 T Soap Dish Pack 1636 043 gt A chrome User Interface for Remote Control f 1636 041 Parking Socket Only 1 464 17 Screw Pack a E gk sesesdl col PEIR 1636 040 t tified A components dented Remote Control Parking Socket 29 Accessories gt 1618 106 Extension Lead and Connector Box Additional 3 metre extension lead to be connected to the Mira Magna DM gt Connect the two cables slide the grommets into the slots of the connector box and carefully push the top half of the connector box onto the bottom half Make sure the two grommets are correctly positioned Connect to the ___ Mira Magna DM x Connector Box Extension Lead 3 m Connect to the User Interface for the DM Data Cable UV or the BIR Dimensions for the UV and the BIR 225 mm 641 mm 792 mm Cleaning gt Many household cleaners contain abrasive and chemical substances and should not be used for cleaning plated or plastic fittings These finishes should be cleaned with a mild washing up detergent or soap solution and then wiped dry using a soft cloth gt To avoid limescale use your thumb or a soft cloth to wipe any limescale from the soft rubber nozzles and the front face of the showerhead Customer Services Guarantee of Quality Mira Showers guarantee your product against any defect in mater2. V Mira Magna UV Shower Mixer gt Note 1 Refer to your Mira Magna DM Installation and User Guide gt Note 2 The Data Cable must be placed through the Suppression Ferrite and then looped around the cover The Suppression Ferrite must be fitted as close to the User Interface as possible Mira Magna UV gt Caution The Mira Magna DM and the Mira Magna UV must be installed within 4 m of each other Longer pipe runs maximum of 7 m will require a 3 m Extension Lead and Connector Box available from Customer Services or your local stockist refer to the section Accessories Note Longer pipe runs will increase water delivery times after temperature adjustment The water delivery system can be installed with a falling supply or rear entry supply The supply option you choose will dictate which top cover is required Loosen the user interface fixing screw Carefully pull the user interface from the backplate Disconnect the interface cable Falling Supply gt Note This product is designed to be fitted to a full height fully tiled or flat waterproof wall surface Put the concealing plate against the ceiling and mark the centre position for the hole Carefully drill a 24 mm hole in the ceiling Fit the concealing plate over the concealing pipe Temporarily insert a 15 mm supply pipe through the concealing pipe Top Cover may differ from the one shown Interface Cable Interface C
3. Mira Magna Water Delivery System Installation and User Guide These instructions are to be left with the user This Installation and User Guide must be read in conjunction with the Mira Magna Digital Mixer Valve Installation and User Guide amp PlumbNation the nation s favourite for 4 FREE SHIPPING 4 SECURE PAYMENTS on all orders over 100 to mainland UK shop online with confidence v FINANCE AVAILABLE 4 PRICE MATCH spread the cost with low interest rates always get the best deals available we have HUGE REDUCTIONS ON THOUSANDS OF ITEMS Boilers Bathroom suites aa eae eee siecle aaah ee cena Pipes amp fittings Wet rooms Cylinders Towel warmers Fires Bathroom furniture Renewable energy amp much more C visit our website a plumbnation co uk 0844 800 3460 Cleaning session Lttceetetee ctevencene acne eavieeccnevvceneceevesasaeeneeedeerres 30 Customer SGrviCe iiiiccicicissscecsciiciacdeceessicchesceesscceasiis vebdanicussceendaseecceceeuns 31 Introduction The Mira Magna Water Delivery System delivers water via the Mira Magna Digital Mixer Mira Magna DM and this guide should be read in conjunction with the Mira Magna DM Installation and User Guide To operate the Mira Magna Water Delivery System use the interface refer to the section Operation for more details This Installation and User Guide covers the following products Mira Magna Universal Variable Water Delivery System M
4. Stop push button at the end of your shower Remote Control Operate the Remote Control gt Using the Warm Up Function gt gt gt Press and momentarily hold the Start push button Water will be delivered on High flow Press and momentarily hold the Warm Up Stop push button at the end of your shower either on the remote or on the interface Pressing the Warm Up Stop push button starts this function refer to the section Warm Up Function for more details Note There is no time delay function when using the remote control Remote Control Caution When using the remote control in its socket press the buttons carefully to avoid accidentally dislodging it from its socket Timeout Function gt The Mira Magna DM is supplied with a timeout default set The shower will operate and automatically shut off after a set period refer to the section Timeout for more details 23 Enable the Mira Magna DM gt gt Note This procedure is required should the remote control or the user interface is replaced Switch the Mira Magna DM s electrical supply OFF and ON Press and hold the Low and Medium push buttons at the same time until the interface stops beeping The Low and High push buttons will flash alternately after a short delay Hold the remote control within 200 mm of the interface Press and momentarily hold either the Start or the Warm Up Stop push button Note The Medi
5. Turn the DM electrical supply OFF and ON to reset the DM Make sure Hot and Cold inlets are not reversed Make sure that the inlet filters are clean If the problem still occurs Contact Customer Services Turn the DM electrical supply OFF and ON to reset the DM Replace Thermistor Pack If the problem still occurs Contact Customer Services Spare Parts List Mira Magna UV g q 464 29 464 18 Suppression Ferrite J DM Data Cable i 464 13 L 464 06 Upper Support Shrouds Concealing Plate 5464 07 464 14 Concealing Pipe Mira Magna Handset Assembly A a 464 24 Magna Spray Plate Pack Upper Support Bracket 623 73 Hose Washer i Service Pack O Seals 464 15 Mira Magna 450 24 Adjuster Ring UV Clamp Bracket Assembly chrome 452 10 pa 450 28 A Slide Bar 2 Dish LC P chrome chrome J A 464 16 Interface lt gt Cable 464 08 Temperature Knob 1636 041 Parking Socket Only User Interface Rear Case 1636 040 Remote Control Parking Socket 464 17 Screw Pack components identified A 28 Mira Magna BIR 464 20 Mira Magna BIR Power Assembly 450 43 BIR Mounting Pack e Z 23 464 24 n ED A 4 CJ Mira Magna i 7 T gt F Spray Plate C Z gt 464 19 Pack DM Data Cable 464 29 z 2 aes Suppression Ferrite A Service Pack O Seals A 464 22 464 21 User Interface Wall Mount Case Mira Magna
6. Mira Magna UV Remote Enabling Timeout gt Press and momentarily hold the Warm Up Stop and Low push buttons at the same time The Low push button will flash and beep three times to confirm the selection is successful gt Note If the Mira Magna DM s electrical supply is switched OFF the Mira Magna DM will revert to the default setting 21 Operation Warm Up Function gt gt Temperature Control Knob Press the Warm Up Stop push button To allow the user to get out of the shower the unit delays for a few seconds before turning on The Warm Up Stop push button flashes for a number of seconds until water comes out of the handset at the selected temperature then turns off Standby mode maximum of 2 minute delay feature 10 minutes for the remote control option before switching off Note The Mira Magna DM is supplied with the default of High Flow for the Warm Up Function Refer to the section Operate the Shower Note A long delay before entering the shower may result in initial temperature fluctuations the unit has switched OFF Note Due to the operational nature of instantaneous water heaters combination boiler systems use of the warm up feature may cause fluctuating temperatures to be delivered and may take a few seconds to stabilise To Change the Warm Up Function for Wireless Remote Control Option Only gt gt Note This can only be set when the DM has not been use
7. Services Refer to Commissioning Maximum Temperature Setting Make sure that the hot and cold water supplies are connected correctly If the problem still occurs Contact Customer Services Operate the remote control in different areas to check range Turn the DM electrical supply OFF and ON to re set the DM If the problem still occurs Contact Customer Services Switch the shower OFF ON with the remote control Turn the DM electrical supply OFF and ON to re set the DM If the problem still occurs Contact Customer Services Self Diagnostic Information DM PCB Error Over Temp at Control Sensor PCB Control Sensor Error Turn the DM electrical supply OFF and ON to reset the DM Replace DM PCB If the problem still occurs Contact Customer Services Turn the DM electrical supply OFF and ON to reset the DM Make sure Hot and Cold inlets are not reversed Make sure that the inlet filters and non return valves are clean If the problem still occurs Contact Customer Services Turn the DM electrical supply OFF and ON to reset the DM Replace DM PCB or the Thermistor pack If the problem still occurs Contact Customer Services DM PCB Error Over Temp at Outlet Sensor Outlet Sensor Error Turn the DM electrical supply OFF and ON to reset the DM Replace DM PCB If the problem still occurs Contact Customer Services
8. able Backplate User interface SP User Interface Fixing Screw Concealing Plate th in Concealing Pipe gt 15 mm Supply Pipe Temporarily insert the slide bar assembly onto the 15 mm supply pipe Note Make sure that the supply pipework is cut squarely and is free from burrs To assist in fitting the end of the pipe should be chamfered to prevent O seal damage The use of a pipe cutter is recommended Hold the slide bar assembly in position on the wall and when it is level mark the positions of the fixing holes Note Make sure that the slide bar ends are pushed fully into the slide bar assembly Note Only 2 fixing holes are required on the bottom slide bar end Remove the slide bar assembly from the wall drill the fixing holes 6 mm and fit the wall plugs Note Make sure that the locking ring is held firmly when pulling the supply pipe from the push fit connector Attach the slide bar assembly to the wall with the fixing screws Cut the concealing pipe and the 15 mm supply pipe to length make sure that the 15mm supply pipe extends through the concealing pipe enough to make a connection into the push fit connector Note The 15 mm supply pipe must enter the push fit connector by 30 mm 10 Locking Ring ep fi L Fixing Screw Wall Plugs Important Do not fit the pipe at this stage Once the pipe assembly has been cut to length re
9. d for a period of 10 minutes or after switching the DM s electrical supply OFF and ON Note Due to the operational nature of instantaneous water heaters combination boiler systems use of the warm up function may cause fluctuating temperatures to be delivered when re started and may take a few seconds to stabilise We recommend that continuous Medium or High Flow modes are used Press and momentarily hold the Low and High push buttons at the same time the unit will beep 3 times and will indicate which warm up mode is set by the flashing of the Low Medium or High push button refer to the following table 22 Pressing the Low and High push buttons twice within 2 seconds selects the next warm up mode Repeat the procedure until you have selected your required warm up mode Refer to the following table Low push button flashing The unit warms up and switches to standby mode no flow Medium push button flashing The unit warms up and switches to medium flow High push button flashing The unit warms up and switches to high flow Operate the Shower gt gt gt gt gt gt Note The shower can be operated without using the Warm Up function Press the Low Medium or High push button Water will come out of the handset at the selected temperature To alter the showering temperature turn the temperature control knob While the showering temperature adjusts the selected flow push button will flash Press the Warm Up
10. e Check cable connections shower will not operate connection Electrical supply isolated or Check electrical supply fuse blown DM Valve breakdown Isolate the electrical supply and turn back on after 30 seconds If the problem persists note the sequence of the flashing push buttons and with the information from Self Diagnostic Information contact Customer Services Continued 25 Continued Malfunction No flow or low flow rate from the Shower Fittings Drip from spray plate assembly on handset or BIR assembly Incorrect shower temperature Remote Control Option The remote control does not operate the shower The interface does not operate correctly Spray plate assembly blocked Hose blocked or twisted DM Valve malfunction A small amount of water may be retained in the shower fitting after the interface has been turned off This may drain over a few minutes DM Valve malfunction Maximum temperature incorrectly set DM Valve incorrectly fitted The remote control is out of range Incomplete signal received from remote control Incomplete signal received from remote control 26 Refer to Cleaning Clear blockage or release twist in hose Contact Customer Services This is quite normal Changing the angle of the shower fitting may vary the draining time Solenoid fault May require cleaning or replacement If the problem still occurs Contact Customer
11. ere ee uae eee F 4 x Wall Plugs LJ tH ts 1 x Soap Dish 1 a Cc o i uy t pi y iU 4x Fixing Screws 1 x Soap Dish ia 4 Wall Bracket U Ex i Di ts 2 x Soap osh i A Wall Plugs if E 2 x Soap Dish EH l 4 Fixing Screws E E y gal f i 1 x User Interface ti 1x Hose Assembly i3 miy nE Me VS og YQ LR 1 x Suppression Ferrite E XS a Mira Magna BIR Wireless Remote Control option Tick the appropriate boxes to familiarise yourself with the part names and to confirm that the parts are included 4 x Mounting 4 x Wall Plugs LJ Plate Screws oS Sag 1 x Backplate LJ 1 x Top Cover J 1 x O Seal u l E NA AXBIR Sew L 1xOlve L N Of Mss Sons 1 x Mounting Plate 2 x Backplate 1 x Backplate Q Screws Nut 4 x Cover Screws Jo 1 x Cover g l 1 x BIR Assembly Assembly Qe a 1 x DM Data Cable L_ 2 x Soap Dish Wall Plugs 2 x Soap Dish Fixing Screws 1 x Soap Dish E 1 x Soap Dish Wall Bracket with Bottom 1 x User Interface Bracket Assembly Lj 1 x Suppression Ferrite LJ Wireless Remote Control Installation Installation Schematic for the UV or the BIR refer to Note 1 3 amp Switched Fused Spur Box refer to Note 1 Suppression Ferrite refer to Note 2 gt a ban Digital Mixer Mira Magna BIR refer to Note 1 Wireless Remote Control W option Mira Magna BIR S Wall Mount d
12. he lock mode option is cancelled Setting Option 2 gt Note This can only be set when the Mira Magna UV has not been used for a period of 3 minutes 10 minutes for the Mira Magna UV Remote or after switching the Mira Magna DW s electrical supply OFF and ON Press and momentarily hold the Warm Up Stop and Medium push buttons at the same time The interface will beep three times to confirm the selection is successful The interface is locked Note Selecting the Warm Up Stop and Medium push buttons at the same time cancels the lock mode option set The Medium push button will flash and beep three times to confirm the lock mode option is cancelled Switching the mixer OFF and ON will also cancel the lock mode option 20 Timeout Allows you to set the flow duration for the shower before it automatically shuts off gt Note This can only be set when the Mira Magna UV has not been used for a period of 3 minutes 10 minutes for the Mira Magna UV Remote or after switching the Mira Magna DW s electrical supply OFF and ON Timeout Selection gt Note The Mira Magna DM timeout function is factory set to run for 30 minutes default setting This timeout period can be changed depending on user preference gt Set the temperature control knob to the desired position refer to the table below for the settings that can be programmed into your Mira Magna DM Timeout Minutes T ae emperature Control Knob Position Mira Magna UV
13. ials or workmanship for the period shown in the Guarantee Registration Document included with your shower Alternatively to confirm the applicable guarantee period please contact Customer Services To validate the guarantee please return your completed registration card Within the guarantee period we will resolve defects free of charge by repairing or replacing parts or modules as we may choose To be free of charge service work must only be undertaken by Mira Showers or our Approved Agents in Northern Ireland and the Republic of Ireland Service under this guarantee does not affect the expiry date The guarantee on any exchanged parts or product ends when the normal product guarantee period expires Not covered by this guarantee Damage or defects arising from incorrect installation improper use or lack of maintenance including build up of limescale Damage or defects if the product is taken apart repaired or modified by any person not authorised by Mira Showers or our Approved Agents This guarantee is in addition to your statutory and other legal rights Before using your shower Please take the time to read and understand the operating and safety instructions detailed in this manual What to do if something goes wrong If when you first use your shower and it doesn t function correctly first contact your installer to check that the installation and commissioning are satisfactory and in accordance with the instructio
14. ing screws into the mounting plate This will prevent the fixing holes from becoming blocked with plaster or grout Finish the surface of the wall as required The copper pipe must protrude through the wall between 23 and 25 mm If the pipe protrudes further than 25 mm it will prevent the backplate nut from engaging with the backplate If necessary cut the pipe to the correct length and remove any burrs Fit the backplate to the wall using the two fixing screws 15 Mounting Plate he ca EN WA gt WAN K cS Nut Mounting Plate com T Threaded Holes Temporarily fit the two backplate fixing screws to prevent holes becoming blocked with grout 23 25 mm 15 mm Copper Pipe Mounting piat M gt Put the compression olive over the copper pipe and tighten the backplate nut into position Note Make sure the supply pipe is not pushed backwards when the backplate nut is secured Make sure the O seal is fitted on the backplate nut Push the BIR assembly over the backplate nut onto the wallplate Attach the BIR assembly to the wall plate using the four screws Attach the upper shroud to the BIR assembly using the four self tapping screws Snap the lower shroud into position Backplate lt Upper Shroud a pp N TA j q lt tS O AA Lower Shroud Shower Cubicle Laminated Panel or Stud Partition Wall gt Cut a 25 mm hole in the pa
15. ipe should be chamfered to prevent O seal damage The use of a pipe cutter is recommended Make sure that the data cable and finished pipework protrude through the wall before the final finished wall surface is completed Put the slide bar assembly in position on the wall and temporarily push fit the soldered elbow into the push fit connector Mark the positions of the top and the bottom fixing holes Note Only 2 fixing holes are required on the bottom slide bar end Remove the slide bar assembly from the wall and drill 6 mm and fit the wall plugs Note Make sure that the locking ring is held firmly when pulling the supply pipe from the push fit connector 12 Supply pipework from the DM 22 mm max Hole Size 30 mm min Soldered Elbow 15 mm Supply Pipe 30 mm Pipe Insertion Push fit in line Connector gt Hold the supply pipe firmly and push m the slide bar assembly onto the Ai supply pipe w gt of l gt Note The supply pipe must enter the push fit connector by 30 mm Fixing Screws gt Attach the slide bar assembly with the fixing screws Fixing Screws i i wia e gt Connect the data and interface cables together gt Attach the top cover onto the slide bar assembly Top Cover Interface Cable I 13 Connect the interface cable to the user interface Attach the user interface to the rear case and secure with
16. ira Magna UV An adjustable spray handset with four different spray actions Start Eco Champagne and Massage is supplied complete with flexible hose clamp bracket assembly slide bar supports combined user interface and a wall mounted soap dish Mira Magna Built in Rigid Water Delivery System Mira Magna BIR An adjustable built in shower head with four different spray actions Start Eco Champagne and Massage supplied with wall mounted soap dish and a user interface Suitable for connection to concealed pipe work supplies only Mira Magna Wireless Remote Control Option The remote control allows the user to start stop and use the warm up feature on the water delivery system over a distance of up to 10 metres The remote control can be used hand held or when located in its parking socket it requires no batteries and is also water resistant not to be immersed in water Design and Patent Registration Design Registration 000592084 00275789 0003 0004 Patent Application Int Pat App WO 2006 072799 Specifications Minimum maintained pressure 0 4 bar Maximum maintained pressure 5 0 bar gt Caution Exceeding the stated maximum maintained pressure could result in excessive spray forces and possible damage to the product This is the typical flow performance graph for the Mira Magna shower fittings only There will be an additional pressure loss through the digital mixer 40 Start 35 Mas
17. m and plug Attach the retainer to the wall with the fixing screws Slide the parking socket onto the retainer Retainer Fixing Screw Parking Socket Wall Plug Retainer Clip Remote Control Cut out Note The parking socket must be placed with the cut out on the bottom To remove the parking socket place a small screwdriver into the cut out lever the retainer clip up and slide the parking socket off Clip the remote control into the parking socket 18 Commissioning General gt Turn on the water supply and check for leaks Setting Maximum Temperature gt Note This can only be set when the Mira Magna UV has not been used for a period of 3 minutes 10 minutes for the Mira Magna UV Remote or after switching the Mira Magna DM s electrical supply OFF and ON For user safety the Mira Magna DM is factory set to give a default maximum temperature of 45 C when the temperature control knob is at position 9 This pre set maximum temperature can be changed depending on user preference The table below shows the other Maximum Temperature Settings that can be programmed into your Mira Magna DM Example Setting the maximum temperature to 40 C a typical showering temperature Rotate the temperature control knob to position 5 and follow the section Enabling the Set Maximum Temperature Temperature Control Knob Position Maximum Temperature Settings C Enabling the Set Maximum Temperature Pres
18. move the 15mm supply pipe from the concealing pipe Put the data cable through the concealing pipe Carefully fit the 15 mm supply pipe through the concealing pipe Make sure that you fit the top cover over the concealing pipe then connect to the push fit connector Connect the data and interface cables together Push the top cover onto the slide bar assembly Connect the interface cable to the user interface Attach the user interface to the rear case and secure with the user interface fixing screw Attach the hose to the outlet connection and to the handset Make sure the hose washers are installed correctly Put the handset into the clamp bracket Make the plumbing connections to the Digital Mixer refer to your Mira Magna DM Installation and User Guide 11 Concealing Pipe Top Cover 7 15 mm Supply Pipe from Digital Mixer V7 Push Fit Connector w User Interface Fixing Screw ar Rear Entry Supply gt Caution Pipework must not be soldered while attached to the water delivery system For rear entry supply pipework a soldered elbow must be used Important Make sure that the dimensions do not exceed the ones shown otherwise you will not be able to fit the unit Note The 15 mm supply pipe must enter the push fit connector by 30 mm Make sure that the supply pipework is cut squarely free from burrs and to assist in fitting The end of the p
19. nel and two 5 5 mm holes at 48 mm centres Put the copper pipe through the mounting plate and panel The copper pipe must protrude through the wall between 23 25 mm from the finished surface of the wall Hold the mounting plate in position behind the panel place the backplate in front of the panel and insert the two backplate screws through the holes in the panel and fit them into the mounting plate and tighten To complete the installation of the BIR fittings refer to the section Mira Magna BIR Solid and Dry lined Walls 16 25 mm Diameter rl 5 5 mm Diameter 5 5 mm Diameter Q ve Mounting Plate A Panel BIR User Interface A gt 4 Ff Loosen the user interface fixing li P 7 screw and separate the user Mag interface from the casing i D gt AWE Hold the casing in position on the i We wall and mark the positions of the W k Wy fixing holes and the position of the cable entry hole if not already 2 7 fitted way User Interface Y Fixing Screw Note Only 2 fixing holes are required to fix the casing to the wall Drill the fixing holes 6 mm the cable entry hole 15 20 mm and fit the wall plugs User Interface Casing DM Cable Warning Make sure that you avoid hidden cable and pipes when drilling holes in the wall Put the DM cable through the central wall Plugs hole Make sure that you do not damage the electrical connec
20. ns commonly referred to as the IEE Wiring Regulations Part 7 or any particular regulations and practices specified by the local electricity supply company The plumbing installation must comply with the requirements of UK Water Regulations Bye laws Scotland Building Regulations or any particular regulations and practices specified by the local water company or water undertakers Anyone who may have difficulty understanding or operating the controls of any shower should be attended whilst showering Particular consideration should be given to e the young e the elderly e the infirm e the disabled anyone who suffers from a medical condition that can result in temporary incapacity e g epilepsy or blackouts anyone inexperienced in the correct operation of the controls Standards and Approvals The Mira Magna complies with all the relevant directives for CE marking 5 Pack Contents Checklist Mira Magna UV Wireless Remote Control option Tick the appropriate boxes to familiarise yourself with the part names and to confirm that the parts are included CJ 2 x Top Covers w 1 x Concealing Plate Wireless Remote Control om i 1 x Handset E aaa S 2 x Hose Washers LJ Re RR PER RERER jSRSSRERcRr F i peETEaz a ea a i ra Pe LI 1 x DM Data cable L_ t E pH 1 x Concealing Pipe ia a SS p EEREE cerrrrr apaepeeec
21. ns in this manual Should this not resolve the difficulty simply contact our Customer Services who will give every assistance and if necessary arrange for our Service Engineer to visit If later the performance of your shower declines consult this manual to see whether simple home maintenance is required Please call our Customer Services to talk the difficulty through request service under guarantee if applicable or take advantage of our comprehensive After Sales Service As part of our quality and training programme calls may be recorded or monitored Our Customer Services Team is comprehensively trained to provide every assistance you may need help and advice spare parts or a service visit Spare Parts We maintain an extensive stock of spares and aim to have functional parts available for ten years from the date of final manufacture of the product Spares can be purchased from approved stockists or merchants locations on request or direct from Customer Services Spares direct will normally be despatched within two working days Payment can be made by Visa or Mastercard at the time of ordering Should payment by cheque be preferred a pro forma invoice will be sent Note In the interests of safety spares requiring exposure to mains voltages can only be sent to competent persons Service Our Service Force is available to provide a quality service at a reasonable cost You will have the assurance of a Mira trained Enginee
22. r Agent genuine Mira spares and a 12 month guarantee on the repair Payment should be made directly to the Service Engineer Agent using Visa MasterCard or a cheque supported by a banker s card To contact us England Scotland amp Wales Mira Showers Customer Services Telephone 0870 241 0888 Mon to Fri 8 00 am to 5 30 pm 8 30 am to 3 30 pm Saturday E mail technical mirashowers com Fax 01242 282595 By Post Cromwell Road Cheltenham Gloucestershire GL52 5EP Northern Ireland Wm H Leech amp Son Ltd Telephone 028 9044 9257 Mon to Fri 9 00 am 5 00 pm E mail leech dnet co uk Fax 028 9044 9234 Post Maryland Industrial Estate Ballygowan Road Moneyreagh Co Down BT23 6BL Republic of Ireland Modern Plant Ltd Dublin Telephone 01 459 1344 Mon to Fri 9 00 am 5 00 pm E mail sales modernplant ie Fax 01 459 2329 Post Otter House Naas Road Clondalkin Dublin 22 Modern Plant Ltd Cork Telephone 021 496 8755 Mon to Fri 9 00 am 5 00 pm E mail cork modernplant ie Fax 021 496 8607 Post Tramore Road Cork 31 1059237 W2 A Mira is a registered trade mark of Kohler Mira Limited The company reserves the right to alter product specifications without notice www mirashowers com FM 14648 magna Kohler Mira Limited October 2006
23. s and momentarily hold the Warm Up Stop and High push buttons at the same time The High push button will flash and beep three times Release the push buttons and re select within 2 seconds The High push button will flash and beep three times to confirm the selection is successful Note Water will be delivered at the new maximum temperature setting control knob position 9 ranging to cold water control knob position 1 19 Safety Lock Mode gt There are two Safety Lock Modes Option 1 Locks the mixer to your flow and temperature settings Option 2 Locks the interface so no push buttons can be used Setting Option 1 Operate the shower set the desired flow and temperature then press and momentarily hold the Warm Up Stop and Medium push buttons at the same time The Medium push button will flash and beep three times to confirm the selection is successful The mixer is locked to your temperature and flow selection Pressing any flow push button will turn the mixer ON Pressing the Warm Up Stop push button turns the mixer OFF Caution If the temperature control knob is altered while the Mira Magna DM is in standby mode or while the shower is in operation the water temperature settings will be changed to the new setting next time the shower is used Note Selecting the Warm Up Stop and Medium push buttons at the same time cancels the lock mode option set The Medium push button will flash and beep three times to confirm t
24. sage 30 Eco Champagne 25 20 Flow Rate litres minute 0 0 5 1 0 15 2 0 Pressure Loss bar Pressure loss Pressure difference between the inlet and outlet of the fitting Important Safety Information Installation must be carried out in accordance with these instructions and must be conducted by designated qualified and competent personnel Warning 1 Products manufactured by us are safe and risk free provided that they are installed used and maintained in good working order in accordance with our instructions and recommendations Make sure that any pipework that could become frozen is properly insulated DO NOT operate this appliance if it is frozen Allow the appliance to thaw before using The shower unit must not be fitted where it may be exposed to freezing conditions This product is not suitable for areas with high humidity e g steam rooms Please consult your installer Due to the operational nature of instantaneous water heaters combination boiler systems use of the warm up feature may cause fluctuating temperatures to be delivered and may take a few seconds to stabilise Caution 1 2 Read all of these instructions and retain this guide for later use The electrical installation must comply to BS 7671 Requirements for Electrical Installatio
25. the user I Attach the hose to the outlet N interface fixing screw connection and to the handset Make sure the hose washers are installed correctly Put the handset into the clamp bracket Make the plumbing connections to the Digital Mixer refer to your Mira Magna DM Installation and User Guide Mira Magna BIR gt Note The BIR fittings can be fitted to a variety of wall surfaces or structures Note If the data cable is chased into a solid wall or installed in ducting the data cable must be installed before the finished wall surface is completed Solid and Dry lined Walls gt Install recessed 15 mm copper pipe from the DM and make sure the pipe will protrude through the finished wall surface by 23 25 mm Loosely screw the backplate to the mounting plate with the two screws provided Place the mounting plate and backplate over the copper pipe 14 23 25 mm Pipe Fit and loosely connect the backplate nut sufficiently to hold the assembly against the wall Mark the position of the mounting plate and its fixing holes on the wall surface Remove the backplate from the mounting plate Drill the four mounting plate fixing holes 6 mm If necessary make arecess approximately 6 mm deep to accept the mounting plate Fit the four wall plugs Fix the mounting plate to the wall with four screws The two threaded holes must be horizontal Temporarily fit the two backplate fix
26. tor Attach the casing to the wall with the fixing screws Fixing Screws Attach the DM cable to the socket in the back of the user interface Attach the user interface and secure with the user interface fixing screw User Interface Fixing Screw 17 Soap Dish Installation gt gt gt gt Remote Control Installation gt Decide on a suitable position for the soap dish Soap Dish Warning Make sure that you avoid hidden cables and pipes when drilling holes in the wall Place the wall bracket on the wall and mark the position of the fixing holes Drill 6 mm and plug Clip the soap dish onto the wall bracket Attach the wall bracket to the wall with Well Bracket the fixing screws Clip the bottom cover onto the wall bracket Bottom Cover Decide on a suitable position for the remote control outside the showering area Refer to the illustration for fixing details Note The remote control can be sited up to 10 m from the user interface Wall thickness and construction will affect this distance so before permanently fixing the parking socket make sure the water delivery system can be operated by the remote control in the desired fixing location refer to the section Operation Remote Control Warning Make sure that you avoid hidden cables and pipes when drilling holes in the wall Place the retainer on the wall and mark the position of the fixing holes Drill 6 m
27. um push button will be illuminated if the remote has been successfully enabled Switch the Mira Magna DM s electrical supply OFF and ON The Mira Magna DM has been enabled and the remote control is ready to be used Adjustable Handset The handset has four different spray modes Start Eco Champagne and Massage gt Start Water flows from the outer set of holes To select the Start mode turn the spray plate anticlockwise from the full clockwise position until it clicks once Eco Water flows from the outer set of holes at a reduced flow rate To select the Eco mode turn the spray plate fully clockwise 24 gt Champagne Water flows from the middle set of holes To select the Champagne mode turn the spray plate anticlockwise from the full clockwise position until it clicks twice gt Massage Water flows from the inner set of holes To select the Massage mode turn the spray plate anticlockwise from the full clockwise position until it clicks three times Fault Diagnosis The trouble shooting information below gives details on what you can do as a user should you encounter difficulties whilst operating the shower If there is a problem with the interface some of the push buttons may flash very fast refer to the section Self Diagnostic Information Malfunction Push buttons are flashing Water supply isolated Check water supply on the interface and or the Damaged or broken cabl
Download Pdf Manuals
Related Search