USER GUIDE & INSTALLATION INSTRUCTIONS
Contents
1. Function Defrost To thaw small items in the oven without heat Fan oven A full cooking function even heat throughout great for baking Fanned grilling Grilling meat and fish with the door closed Fan assisted A full cooking function good for roasting and baking Conventional oven A full cooking function for roasting and baking in the lower half of the oven Browning element To brown and crisp cheese topped dishes Base heat To crisp up the bases of quiche pizza or pastry Table 2 1 The Glide out Grill Open the door and pull the grill pan carriage forward using the handle Fig 2 15 The grill has two elements that allow either the whole area of the pan to be heated or just the right hand half Adjust the heat to suit by turning the knob To heat the whole grill turn the knob clockwise Fig 2 16 To heat the right hand half turn the knob counter clockwise The neon indicator light by the grill control will come on For best results slide the carriage back into the grill chamber and preheat the appropriate part s of the grill for two minutes The grill trivet can be removed and the food placed on it while you are waiting for the grill to preheat A DO NOT leave the grill on for more than a few moments without the grill pan underneath it otherwise the knobs may become hot Once the grill has preheated slide the carriage out again With the tri2. u DO NOT box the cooker in it must be possible to move the cooker in and out for cleaning and servicing i a E If the cooker is near a corner of the kitchen a clearance of 130mm is required to allow the oven doors to open Fig 7 3 The actual opening of the doors is slightly less but this allows for some protection of your hand as you open the door 130mm minimum When Fitting Between Kitchen Cabinets We recommend that you either A _ Fit the cooker so that any cabinet doors are at least 30mm behind the cooker door fronts Note that this may require an infill piece behind the cooker We recommend a gap of 1110 mm between units to allow for moving the cooker B Leave a gap of at least 14mm on either side of the cooker a 1120 mm gap between units The cooker should be positioned centrally We also recommend that you do not final fix any adjacent cabinets until the cooker is installed Decorative mouldings or handles on cabinet doors and fronts may interfere with the opening of the oven doors 21 INSTALLATION Check the appliance is electrically safe and gas sound when you have finished Moving the Cooker On no account try and move the cooker while it is plugged into the electricity supply A The cooker is very heavy so take great care We recommend that two people manoeuvre the cooker Make sure that the floor covering is firmly fixed or removed to prevent it being disturbed when moving th
3. Replace the grill pan When refitting the grill pan make sure that the wide rim is at the front Fig 5 9 14 Control Panel and Doors Avoid using any abrasive cleaners including cream cleaners For best results use a liquid detergent The same cleaner can also be used on the doors or alternatively using a soft cloth wrung out in clean hot soapy water but take care that no surplus water seeps into the appliance After cleaning polish with a dry cloth Ovens Cook amp Clean Panels The ovens have panels which have been coated with a special enamel that partly cleans itself This does not stop all marks on the lining but helps to reduce the amount of manual cleaning needed The Cook amp Clean panels work better above 200 C If you do most of your cooking below this temperature occasionally remove the panels and wipe with a lint free cloth and hot soapy water The panels should then be dried and replaced and the oven heated at 200 C for about one hour This will make sure the Cook amp Clean panels are working effectively Do not use steel wool oven cleaning pads or any other materials that will scratch the surface Removing the Oven Linings Some of the lining panels can be removed for cleaning If you wish to clean the enamel interior of the oven you will need to remove the shelves before removing the Cook amp Clean panels You do not have to remove the support brackets to remo
4. amp Taps Registered in England and Wales Registration No 354715 Registered Office Juno Drive Leamington Spa Warwickshire CV31 3RG Rangemaster continuously seeks improvements in specification design and production of products and thus alterations take place periodically Whilst every effort is made to produce up to date literature this booklet should not be regarded as an infallible guide to current specification nor does it constitute an offer for the sale of any particular appliance C
5. C 190 15 minutes per 500g 15 minutes of the stuffing Duck 160 C 150 25 30 minutes per 500g Bob test ol froze GI packed poultry follow instructions on the 200 C 190 20 minutes per 500g pack Thoroughly thaw frozen Casserole 140 150 C 130 140 2 4 hours according to recipe poultry before cooking Yorkshire Pudding 220 C 210 Large tins 30 35 minutes individual 10 20 minutes Cake Very rich fruit Christmas 140 C B 130 45 50 minutes per 500g of mixture Using the conventional oven when wedding etc two tier cooking leave at least one Fruit 1 i 01 runner space between shelves in Bomm m 150 O B 140 LE Position the baking tray with the Fruit 230 mm tin 150 C B 140 Up to 3 hours front edge along the front of the Madeira 180 mm 160 C B 150 80 90 minutes oven shelf Queen cakes 190 C B 180 15 25 minutes Scones 220 C B 210 10 15 minutes Victoria sandwich 180 mm tin 180 C B 170 20 30 minutes 210 mm tin 180 C B 170 30 40 minutes Up to three tiers can be cooked in a Desserts fan oven atthe same time but make sure to leave at least one runner Shortcrust tarts 200 C B 190 20 30 minutes on a preheated tray space between each shelf being Fruit pies 200 C B 190 35 45 minutes cooked on Tartlets 200 C B 190 10 20 minutes according to size Puff pastry 210 C B 200 20 40 minutes according to size Meringues 100 C B 90 2 3 hours Using the conventional oven for z even browning the maximum size of Baked egg c
6. as asbestos or mesh mats are NOT recommended Fig 2 6 They will reduce burner performance and could damage the pan supports You should also avoid using unstable and misshapen pans that may tilt easily and pans with a very small base diameter e g milk pans single egg poachers Fig 2 7 The minimum recommended pan diameter is 120 mm The maximum allowable pan base diameter is 260 mm DO NOT use cooking vessels on the hotplate that overlap the edges Wok Burner The wok burner is designed to provide even heat over a large area They are ideal for large pans and stir frying Fig 2 8 For heating smaller pans the aforementioned hotplate burners may be more efficient You should wipe the enamel top surface of the cooker around the hotplate burners as soon as possible after spills occur Try to wipe them off while the enamel is still warm Note The use of aluminium pans may cause metallic marking of the pan supports This does not affect the durability of the enamel and may be cleaned off with an appropriate metal Cleaner The Wok Cradle The wok cradle is designed to fit a Professional 35 cm wok If you use a different wok make sure that it fits the cradle Woks vary very widely in size and shape It is important that the wok sits down on the pan support however if the wok is too small the ring will not support it properly Fig 2 9 The cradle should be used on the triple ring wok burners only When you fit the
7. at the top of the oven is greater than at the base when using this function This is a fast intensive form of cooking keep an eye on the food cooking until you have become accustomed to this function Conventional Oven Top and Base Heat This function combines the heat from the top and base elements It is particularly suitable for roasting and baking pastry cakes and biscuits Food cooked on the top shelf will brown and crisp faster than on the lower shelf because the heat is greater at the top of the oven than at the base as in Fan Assisted Oven function Similar items being cooked will need to be swapped around for even cooking This means that foods requiring different temperatures can be cooked together using the cooler zone in the lower half of the oven and hotter area to the top The exposed top element may cook some foods too quickly so we recommend that the food be positioned in the lower half of the oven to cook The oven temperature may also need to be lowered Browning Element This function uses the element in the top of the oven only It is a useful function for the browning or finishing of pasta dishes vegetables in sauce shepherds pie and lasagne the item to be browned being already hot before switching to the top element Base Heat This function uses the base element only It will crisp up your pizza or quiche base or finish off cooking the base of a pastry case on a lower shelf It is also a ge
8. baking tray If available use a multi purpose dry chemical or foam type fire extinguisher Cooking high moisture content foods can create a steam burst when the oven door is opened When opening the oven stand well back and allow any steam to disperse Take care that no water seeps into the appliance A This appliance is heavy so take care when moving it Cooker Care As steam can condense to water droplets on the cool outer trim of the oven it may be necessary during cooking to wipe away any moisture with a soft cloth This will also help to prevent soiling and discolouration of the oven exterior by cooking vapours Cleaning In the interests of hygiene and safety the cooker should be kept clean at all times as a build up in fats and other food stuff could result in a fire Clean only the parts listed in this guide Clean with caution If a wet sponge or cloth is used to wipe spills on a hot surface be careful to avoid steam burns Some cleaners can produce noxious fumes if applied to a hot surface 2 Cooker Overview N SLIT TITY 11V a d Ld SEE qu Q O a ae P RE T The 110 dual fuel cooker Fig 2 1 has the following features 6 hotplate burners including 2 wok burners A control panel A glide out grill Main multi function oven Fan oven mm ON BD Storage drawer Hotplate Burners The drawing by each of the central knob
9. extract into the mixture and then fold in the sifted flour and baking powder 5 Pourthe cake mix over the fruit and bake on the centre shelf of the oven for 15 20 minutes or until the mixture is cooked through and golden on the top 6 Dust with icing sugar and serve immediately with cream or cr me fraiche ROAST LOIN OF PORK WITH PROSCIUTTO amp BAY LEAVES Ingredients 3kg 6 lb skinned and boned loin of pork e 2x70g packs prosciutto Grated zest of 2 lemons e Bay leaves Salt and freshly ground black pepper For the sauce e 1 tablespoons plain flour 4tablespoons lemon juice Chicken stock water Method 1 Preheat the oven to 220 C for a conventional oven 200 C for a fan oven or gas mark 7 2 Spread one of the packs of prosciutto over a chopping board place the pork on top with the outer fat part of the pork resting on the prosciutto 3 Sprinkle the lemon zest onto the inside of the meat and season well Lay the remaining prosciutto on top of the zest and roll up 4 Secure the pork with string or silicone bands and thread bay leaves under the string covering the whole piece of pork Put the meat on to a trivet over a large roasting tin containing enough water to cover the base 5 Place into the oven and cook for 30 minutes Reduce the heat to 180 C conventional oven 160 C fan oven gas 4 and continue roasting for a further 25 minutes per 500g Should the prosciutto start becomin
10. heat and moisture in the room in which it is installed Therefore make sure that the kitchen is well ventilated keep natural ventilation holes open or install a powered cookerhood that vents outside If you have several burners on or use the cooker for a long time open a window or turn on an extractor fan Personal Safety A DO NOT modify this appliance A This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Children shall not play with the appliance Cleaning and user maintenance shall not be made by children without supervision A WARNING The appliance and its accessible parts become hot during use and will retain heat even after you have stopped cooking Care should be taken to avoid touching heating elements Children less than 8 years of age shall be kept away unless continuously supervised CAUTION A long term cooking process has to be supervised from time to time A short term cooking process has to be supervised continuously Danger of fire DO NOT store items on the cooking surfaces To avoid overheating DO NOT install the cooker behind a decorative door gt gt gt P Accessible parts will become hot during use and will retain heat even after you have stopped coo
11. of the instructions Grill Check Turn on the grill control and check that the grill heats up Oven Check Turn on the ovens Check that the oven fans start to turn and that the ovens start to heat up Note The oven light bulb is not included in the guarantee Turn off the ovens Final Fitting Fitting the Pan Supports Please note that the outer pan supports are handed and may prevent the centre pan supports from fitting correctly There is a small indent in the rear of each of the outer supports This indent should be towards the outer edge of the cooker Fig 7 14 Fitting the Plinth Loosen the 3 screws along the front bottom edge of the cooker Hook the central keyhole over the central screw Twist and fit each end keyhole over their respective screws Tighten the fixing screws Fig 7 15 Customer Care Installer Please complete your details in this guide inform the user how to operate the cooker and hand over the instructions Thank you Current Operated Earth Leakage Breakers The combined use of your cooker and other domestic appliances may cause nuisance tripping so we recommend that the cooker is protected on an individual RCD Residual Current Device or RCBO Residual Current Breaker with Overload IF IN DOUBT PLEASE CONSULT A SUITABLY QUALIFIED ELECTRICIAN Fig 7 13 230 V ac 50 Hz 25 WARNING SERVICING TO BE CARRIED
12. position the handles away from the edge of the hotplate A DO NOT use cooking vessels on the hotplate that overlap the edges Never leave the hotplate unattended at high heat settings Pans boiling over can cause smoking and greasy spills may catch on fire Use a deep fat thermometer whenever possible to prevent fat overheating beyond the smoking point A WARNING Unattended cooking on a hob with fat or oil can be dangerous and may result in fire A NEVER leave a chip pan unattended Always heat fat slowly and watch as it heats Deep fry pans should be only one third full of fat Filling the pan too full of fat can cause spill over when food is added If you use a combination of oils or fats in frying stir them together before heating or as the fats melt Foods for frying should be as dry as possible Frost on frozen foods or moisture on fresh foods can cause hot fat to bubble up and over the sides of the pan Carefully watch for spills or overheating of foods when frying at high or medium high temperatures Never try to move a pan of hot fat especially a deep fat fryer Wait until the fat is cool Do not use the top of the flue the slots along the back of the cooker for warming plates dishes drying tea towels or softening butter A DO NOT use water on grease fires and never pick up a flaming pan Turn the controls off and then smother a flaming pan on a surface unit by covering the pan completely with a well fitting lid or
13. recommend that this is carried out before installation See the instructions that are supplied with the conversion kit Handyrack After converting the appliance please attach the Gas Conversion sticker over the appropriate area of the data badge this will identify the gas type for which the appliance is now set You will need the following equipment to complete the cooker installation satisfactorily Stability bracket If the cooker is to be supplied with gas through a flexible hose a stability bracket or chain MUST be fitted These are not supplied with the cooker but are T re N available at most builders merchants N Gas pressure tester manometer N p Flexible gas hose Must be in accordance with the NG JUL BA relevant standards Plinth Multimeter For electrical checks You will also need the following tools 1 Electric drill 2 Masonry drill bit only required if fitting the cooker on a stone or concrete floor 3 Wall plugs only required if fitting the cooker on a stone or concrete floor 4 Steel tape measure 5 Cross head screwdriver 6 Flathead screwdriver 7 Spirit level 8 Pencil 9 Adjustable spanner 10 Allen keys supplied 11 Screws for fitting stability bracket 12 13mm spanner or socket wrench 20 INSTALLATION Check the appliance is electrically safe and gas sound when you have finished Positioning the Cooker Fig 7 1 shows the minimum recommended dista
14. GEmaster M RA Britain s No 1 Range Cooker USER GUIDE amp INSTALLATION INSTRUCTIONS Elise 110 Dual Fuel FRUITY BAKED PUDDING Serves 4 6 Ingredients Oil for greasing 100g strawberries 100g raspberries 100g redcurrants 100g blackberries ora400g mixture of any soft fruits 2medium eggs 30g caster sugar 80ml skimmed milk 2tsp vanilla extract 60g plain flour sifted ltsp baking powder Icing sugar to dust RANGEMASTER COOKWARE Our range cookers are well known for providing the best possible cooking performance and years of faithful service However a great cooker alone cannot guarantee perfect results every time The other vital ingredients are of course enthusiasm and quality cookware We offer cookware to work perfectly with all fuel types manufactured by Rangemaster including induction hobs You can be assured of functionality with style as well as the quality and meticulous attention to detail you expect from the pioneers of range cooking Visit www rangemastercookshop co uk Method 1 Preheat the oven to 200 C for a conventional oven 180 C for a fan oven or gas mark 6 2 Lightly grease a dish 26cm wide x 4cm deep 3 Thickly slice any large strawberries and place them with the other fruits into an ovenproof dish deep enough so the berries are about 2 deep 4 Whisk the eggs and caster sugar until pale and fluffy Beat the milk and vanilla
15. General Oven Tips The wire shelves should always be pushed firmly to the back of the oven Baking trays with food cooking on them should be placed level with the front edge of the oven s wire shelves Other containers should be placed centrally Keep all trays and containers away from the back of the oven as overbrowning of the food may occur For even browning the maximum recommended size of a baking tray is 340 mm 13 by 340mm 13 When the oven is on do notleave the door open for longer than necessary otherwise the knobs may get very hot Always leave a finger s width between dishes on the same shelf This allows the heat to circulate freely around them To help keep your oven clean cover meat when roasting with foil or use a roasting bag To reduce fat splashing when you add vegetables to hot fat around a roast dry them thoroughly or brush lightly with cooking oil Where dishes may boil and spill over during cooking place them on a baking tray If you want to brown the base of a pastry dish preheat the baking tray for 15 minutes before placing the dish in the centre of the tray 11 4 Cooking Table The oven control settings and cooking times given in the table below are intended to be used AS A GUIDE ONLY Individual tastes may require the temperature to be altered to providea preferred result Food is cooked at lower temperature in a fan oven than in a conventional oven When using recip
16. O UT ONLY BY AN AUTHORISED PERSON Disconnect from electricity and gas before servicing Check appliance is safe when you have finished 8 Conversion to LP Gas Grub screw r mu Grub screw Check the Technical Data section at the back of the book that the hob is convertible to the gas you want to use A suitably competent person must perform the conversion After conversion the installation must comply with the relevant regulations and the local electricity supply company requirements Read the instructions before converting this appliance A Failure to convert the appliance correctly could invalidate any warranty or liability claims and lead to prosecution A When servicing or replacing gas carrying components disconnect from the gas supply before starting operation Check the appliance is gas sound after completion A DO NOT use reconditioned or unauthorised gas controls A Disconnect from the electrical supply before servicing Before electrical reconnection check the appliance is electrically safe Injectors Remove the burner caps and heads Remove the old jets Fig 8 1 Fit the new jets see the Technical Data section at the back of the book for correct jets Reassemble in the reverse order Tap Adjustment Removing the Control Panel Pull off all the control knobs Using a 2 5mm Allen key undo the 2 retaining screws in the base at each end of the handrail and remov
17. al gas 20 mbar 230 400V 50Hz Butane 29 mbar Propane 37 mbar See appliance badge for test pressures Dimensions Overall Height minimum 910mm maximum 930mm Overall width 1092 mm Overall depth 595 mm to front of fascia 646 mm over handles Minimum height to the hotplate 650mm Refer to Positioning the Cooker Ratings Bypass Natural Gas 20 mb L P Gas Hotplate M Screw Injector Injector internal 80 internal 54 Wok Burner 3 5 kW 246 g h external 129 external 77 Large Burner X 134 3 0kW 210g h 87 Medium Burner 109 1 7 kW 119 g h 68 Small Burner 75 1 0 kW 70 g h 51 The valves in this cooker are fitted with adjustable bypass screws The cooker is supplied with the bypass screws set for Natural gas For LPG conversion the bypass screws must be screwed all the way down Oven Efficiency om tt etn Fee Coen Multi function Forced Air Convection Maximum power output 230V 50Hz 2 5 kW 2 5 kW Energy efficiency class on a scale of A more efficient to G less efficient A A Energy consumption based on standard load 0 95 kWh 0 90 kWh Usable volume litres 69 69 Size Large Large Time to cook standard load 41 minutes 41 minutes Surface area of the grid 1400 cm 1400 cm 2 3kW Maximum total electrical load at 230V approximate total including oven lights oven fan etc 7 4 kW 29 Notes 30 Name of Appliance amp Col
18. and fixed firmly to the rear of the cooker If you are using a stability bracket Fig 7 8 and Fig 7 9 then adjust the bracket to give the smallest practicable clearance between the bracket and the engagement slot in the rear of the cooker Fit the bracket so that it engages as far as possible over the chassis of the cooker Typical floor mounting 22 INSTALLATION Check the appliance is electrically safe and gas sound when you have finished Repositioning the Cooker Following Connection If you need to move the cooker once it has been connected then you need to unplug it and having gripped under the fascia panel and lifted the front of the cooker slightly Fig 7 7 you need to check behind the cooker to make sure that the gas hose is not caught As you progress make sure that both the electricity cable and gas hose always have sufficient slack to allow the cooker to move With a stability chain fitted release it as you ease the cooker out Do not forget to refit it when you replace the cooker When you replace the cooker again check behind to make sure that the electricity cable and gas hose are not caught or trapped Conversion to Another Gas If the appliance is to be converted to another gas do the conversion at this point See the conversion section of these instructions and see the instructions in the conversion kit Levelling You are recommended to use a spirit level on a shelf in one of the ovens
19. ck of the cooker should be raised up or the front lowered If the cooker is not level arrange for your supplier to level it for you Oven not coming on Is the power on If not there may be something wrong with the power supply Is the cooker supply on at the isolator switch Oven temperature getting hotter as the cooker gets older If turning the temperature down using the oven control knob has not worked or has only worked for a short time then you may need a new thermostat This should be fitted by a service person 17 An oven light is not working The bulb has probably burnt out You can buy a replacement bulb which is not covered under the warranty from a good electrical shop Ask for a 15 W 230V lamp FOR OVENS It must be a special bulb heat resistant to 300 C Fig 6 1 Turn off the power at the circuit breaker Before removing the existing bulb turn off the power supply and make sure that the oven is cool Open the oven door and remove the oven shelves Unscrew the bulb cover by turning counter clockwise It may be very stiff Fig 6 2 Taking care to protect your fingers with a glove in case the bulb should shatter unscrew the old bulb Screw in the new bulb screw back the bulb cover Turn on the circuit breaker and check that the bulb now lights The oven door is misaligned The bottom hinge of either oven door can be adjusted to alter the angle of the door Fig 6 3 Loosen the bottom
20. cooker is supplied with drop shelves Fig 2 22 The drop shelf increases the possibilities for oven shelf spacing The oven shelves can be easily removed and refitted Front Pull the shelf forward until the back of the shelf is stopped by the shelf stop bumps in the oven sides Fig 2 23 Lift up the front of the shelf so the back of the shelf will pass under the shelf stop and then pull the shelf forward Fig 2 24 To refit the shelf line up the shelf with a groove in the oven side and push the shelf back until the ends hit the shelf stop Lift up the front so the shelf ends clear the shelf stops and then lower the front so that the shelf is level and push it fully back Fig 2 25 The Handyrack Main Oven The Handyrack Fig 2 26 fits to the left hand oven door only Food cooking on it is easy to attend to because it is accessible when the door is open The maximum weight that can be held by the Handyrack is 5 5 kg 121b It should only be used with the supplied roasting tin which is designed to fit the Handyrack Any other vessel could be unstable It can be fitted at two different heights One of the oven shelves must be removed and the other positioned to suit When the Handyrack is used in its highest position other dishes can be cooked on the bottom shelf position or base of the oven When the Handyrack is used in its lowest position other dishes can be cooked on the second shelf position or base
21. cradle check that it is supported properly on a pan support and the wok is sitting level in the cradle Fig 2 10 The cradle will get very hot in use allow plenty of time for it to cool before you pick it up The Griddle optional The griddle fits the centre left pan support front to back Fig 2 11 It is designed for cooking food on directly DO NOT use pans of any kind on it The griddle surface is non stick and metal cooking utensils e g spatulas will damage the surface Use heat resistant plastic or wooden utensils A DO NOT put it crossways it will not fit properly and will be unstable Fig 2 12 A DO NOT put it on any other burners it is not designed to fit in any of the other pan supports Position the griddle over the hotplate burners resting on the pan support Fig 2 13 Check that it is securely located The griddle can be lightly brushed with cooking oil before use Light the hotplate burners Adjust the flame heights to suit Preheat the griddle for a maximum of 5 minutes before adding food Leaving it longer may cause damage Turn the control knobs towards the low position marked with the small flame symbol to reduce the burner flames Always leave space around the griddle for the gases to escape A NEVER fit two griddles side by side Fig 2 14 After cooking allow the griddle to cool before cleaning
22. e Fig 8 2 Using a 2mm Allen key undo the 2 retaining screws in the base and side of each handrail support and remove Remove the 3 fixing screws A from the underside of the control panel Fig 8 3 Remove the 2 screws B that were hidden by the handrail supports Lift the control panel clear taking care not to damage or strain the wiring Bypass Screw Adjustment Turn the bypass screw on each control clockwise to the stop Fig 8 4 Refit the control panel Locate the holes in the top edge on the tags on the inner panel and replace the fixing screws in the bottom edge Stick on Label Stick the LP gas label over the natural gas part of the appliance data label 26 WARNING SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON Disconnect from electricity and gas before servicing Check appliance is safe when you have finished Pressure Testing Connect the appliance to the gas supply Check the appliance is gas sound The gas pressure can be measured at one of the hotplate burner jets not a wok burner Lift off a burner head Fit the pressure gauge to the jet Turn on and light one of the other burners with a match Turn on and press in the control knob for the burner with the pressure gauge fitted After checking the pressure turn off the taps and replace the burner head Reassemble burner top making sure it is reassembled in the correct way on the burner body Check the appliance is gas sound Ch
23. e cooker around To help you there are two levelling rollers at the back and two screw down levelling feet at the front Remove the polystyrene base pack From the front tilt the cooker backwards and remove the front half of the polystyrene base Fig 7 4 Repeat from the back and remove the rear half of the polystyrene base Lowering the Two Rear Rollers To adjust the height of the rear of the cooker first fit a 13 mm spanner or socket wrench onto the hexagonal adjusting nut Fig 7 5 Rotate the nut clockwise to raise counter clockwise to lower Make 10 complete 360 turns clockwise Make sure you lower BOTH REAR ROLLERS Completing the Move Unfold the rear edge of the cardboard base tray Open the grill door and right hand oven door so that you can get a good grip on the bottom of the fascia panel as you move the oven Fig 7 6 Carefully push the cooker backwards off the base tray Remove the base tray Position the cooker close to its final position leaving just enough space to get behind it DO NOT use the door handles or control knobs to manoeuvre the cooker Fitting the Stability Bracket or Chain Unless otherwise stated a cooker using a flexible gas connector must be secured with a suitable stability device Suitable stability devices are shown in Fig 7 7 Fig 7 8 and Fig 7 9 If you are using a stability chain Fig 7 7 then the chain should be kept as short as is practicable
24. e many varied uses We suggest you keep a careful eye on your cooking until you are familiar with each function Remember not all functions will be suitable for all food types Please remember that all cookers vary temperatures in your new ovens may differ to those in your previous cooker Multi function Oven Functions Defrost This function operates the fan to circulate cold air 646 only Make sure the temperature control is at 0 C and that no heat is applied This enables small items such as desserts cream cakes and pieces of meat fish and poultry to be defrosted Defrosting in this way speeds up the process and protects the food from flies Pieces of meat fish and poultry should be placed on a rack over a tray to catch any drips Be sure to wash the rack and tray after defrosting Defrost with the oven door closed Large items such as whole chickens and joints should not be defrosted in this way We recommend this be carried out in a refrigerator Defrosting should not be carried out in a warm oven or when an adjoining oven is in use or still warm Make sure that dairy foods meat and poultry are completely defrosted before cooking Fan Oven This function operates the fan and the heating element around it An even heat is produced throughout the oven allowing you to cook large amounts quickly Fan oven cooking is particularly suitable for baking on several shelves at one time and is a good all round func
25. e may appear on the back This is normal and will not affect the performance of your griddle Glide out Grill Before you remove any of the grill parts for cleaning make sure that they are cool or use oven gloves The grill pan and trivet should be washed in hot soapy water Alternatively the grill pan can be washed in a dishwasher After grilling meats or any foods that soil leave to soak for a few minutes in the sink immediately after use Stubborn particles may be removed from the trivet by using a nylon brush The grill pan can be easily removed for cleaning as follows Remove the grill pan support frame by pulling the grill pan forward Fig 5 5 Lift the grill pan clear of the support frame The support frame is held to the side rails by two clips on each side Fig 5 6 For each side support the side rail with one hand and with the other hand lift the frame up and out of the side clips Fig 5 7 For safety push the side rails back into the grill chamber If you need to remove the side rails to allow cleaning of the grill chamber you can unhook them from the grill chamber sides Fig 5 8 and wipe the sides clean with a soft cloth and mild detergent DO NOT put the side runners in a dishwasher Once you have finished hook the side rails back onto the sides of the chamber To refit the frame pull the side rails forward and for each side in turn support the side rail and press the frame down into the side rails
26. eck operation of all the burners 27 9 Circuit Diagram 3p C4 gr KS OS Or Q LL LL Il L N mi Key The connections shown in the circuit diagram are for single phase The ratings are for 230V 50 Hz Description Description Colour Grill control Right hand fan oven thermostat Blue Grill front switch Right hand fan oven control switch Brown Left hand grill element Right hand fan oven element Black Right hand grill element Right hand oven fan Orange Left hand MF oven thermostat Oven light switch Red Left hand MF oven control switch Oven lamp Violet Left hand MF oven base element Ignition switch White Left hand MF oven top element outer pair Ignition generator Yellow Left hand MF oven browning element inner pair Cooling fan Green yellow Left hand MF oven fan element Neon Left hand MF oven oven fan Thermal cut out Grey 28 10 Technical Data THE COOKER IS CATEGORY Catll2H3 It is supplied set for group H natural gas A conversion kit from NG to LP is packed with the cooker INSTALLER Please leave these instructions with the User DATA BADGE LOCATION Cooker back serial number repeater badge below oven door opening COUNTRY OF DESTINATION GB IE Connections Gas Rp at rear right hand side Eletric Natur
27. es reduce the fan oven temperature by 10 C and the cooking time by 5 10 minutes The temperature in the fan oven does not vary with height in the oven so you can use any shelf Conventional Oven Fan Oven Temperature C Temperature Top T Centre C Base B Oven Shelf Positions T Top C Centre B Base Food Shelf Position Approximate Cooking Time Meat Beef no bone 160 C 150 30 35 minutes per 500g 30 35 minutes Thoroughly thaw frozen joints before 200 C 190 20 25 minutes per 500g 20 25 minutes 00king Meat may be roasted at Lamb 160 150 30 35 minutes per 500g 30 35 minutes Pork 160 150 35 40 minutes per 500g 35 40 minutes C C 200 C 190 25 30 minutes per 500g 25 30 minutes C C 220 C 210 C for fan oven and the cooking time adjusted accordingly For stuffed and rolled meats add approximately 10 minutes per 500g or cook at 200 C 190 C for 20 200 C 190 25 30 minutes per 500g 25 30 minutes minutes then 160 C 150 C for the Poultry remainder Chicken 160 C 150 20 25 minutes per 500g 20 25 minutes For stuffed poultry you could cook 200 C 190 15 20 minutes per 500g 15 20 minutes 200 C 190 C for 20 minutes p 3 then 160 C 150 C for remainder Turkey 160 C 150 20 minutes per 500g 20 minutes Do not forget to include the weight 200
28. g too brown cover with some foil 6 When the pork is cooked place onto a warm plate cover with foil and allow to rest for at least 20 minutes 7 Spoon off most of the fat from the roasting tin and stir the flour into the remaining Gradually add the stock and lemon juice adding more stock until the desired consistency is reached and simmer for 5 minutes Check the seasoning adding more pepper or lemon juice as necessary 8 Remove the string or bands from the pork and carve into slices serve with the sauce Contents Before You Start 1 Troubleshooting 17 ML l Installation 19 Installation and Maintenance 1 Peculiar Smells 1 Dear Installer 19 If You Smell Gas 1 Safety Requirements and Regulations 19 ae Provision of Ventilation 19 Ventilation 1 Personal Safety 1 Location of Cooker 20 Cooker Care 2 Conversion 20 Cleaning 2 Positioning the Cooker 21 Moving the Cooker 22 Cooker Overview 3 Fitting the Stability Bracket or Chain 22 Hotplate Burners 3 Repositioning the Cooker Following 23 Wok Burner 4 Connection The Wok Cradle 5 Conversion to Another Gas 23 The Griddle optional 5 Levelling 23 The Glide out Grill 6 Fitting the Handrail 23 The Ovens 6 Gas Connection 24 Accessories 9 Electrical Connection 25 Main Oven Light 10 Final Checks 25 Storage 10 Final Fitting 25 Customer Care 25 3 Cooking Tips 11 Cooking with a Multi function Oven 11 8 Conversion to LP Gas 26 General Oven Tips 11 Inject
29. head Fig 5 1 The Wok Burner The wok burner can also be taken apart for cleaning When reassembling the wok burner Fig 5 2 turn over the large base ring and find the D shaped area Fig 5 3 Turn the head until the D matches the one on the burner base Flip the burner over once again and place it on the burner base To fit the small inner burner find the larger electrode notch in the burner rim Line this up with the white ignition electrode and place the inner burner on the large base ring Fig 5 4 Now fit the two burner caps making sure that they are seated properly Check the burner ports are not blocked If a blockage occurs remove stubborn particles using a piece of fuse wire The Wok Cradle Recommended cleaning materials are hot soapy water a moistened soap pad cream cleaner or a nylon scourer A Inner burner cap B Outer burner cap C Inner burner head D Outer burner head E Wok burner base A Electrode notch B Ignition electrode 13 The Griddle Always clean the griddle after use Allow it to cool completely before removing Immerse the griddle plate in hot soapy water Use a soft cloth or for stubborn stains a nylon washing up brush Note If the griddle is washed in a dishwasher then some dishwasher residu
30. hinge fixing screws and use the notch and a flat bladed screwdriver to move the position of the hinge to set the hinge position Fig 6 4 Retighten the hinge screws Oven door omitted for clarity 18 INSTALLATION Check the appliance is electrically safe and gas sound when you have finished 7 Installation Dear Installer Before you start your installation please complete the details below so that if your customer has a problem relating to your installation they will be able to contact you easily Installer s Name Installer s Company Installer s Telephone Number Appliance Serial Number Safety Requirements and Regulations This cooker must be installed in accordance with the relevant instructions in this booklet with the relevant national and local regulations and with the local gas and electricity supply companies requirements Before installation make sure that the cooker is suitable for your gas type and supply voltage See the data badge The appliance must be installed in accordance with the regulations in force and only in a well ventilated space Read the instructions before installing or using this appliance gt gt P P In your own interest and that of safety it is law that all gas appliances be installed by competent persons Failure to install the appliance correctly could invalidate any warranty or liability claims and lead to prosecution Th
31. hotplate burners faulty Is the power on If not there maybe something wrong with the power supply Are the sparker ignition electrode or burner slots blocked by debris Are the burner trim and caps correctly located See the section on Cleaning Hotplate burners will not light Make sure that the burner parts have been replaced correctly after wiping or removing for cleaning Check that there is not a problem with your gas supply You can do this by making sure that other gas appliances you may have are working Do the burners spark when you push the button If not verify that the power is on Steam is coming from the oven When cooking foods with high water content e g oven fries there may be some steam visible at the rear grille Take care when opening the oven door as there may be a momentary puff of steam when the oven door is opened Stand well back and allow any steam to disperse What cleaning materials are recommended for the cooker See the Cleaning section for recommended cleaning materials Never use caustic or abrasive cleaners as these will damage the surface An oven fan is noisy The note of the oven fan may change as the oven heats up this is perfectly normal The knobs get hot when I use the oven or the grill Can I avoid this Yes this is caused by heat rising from the oven or the grill and heating them up Do not leave the oven door open Make sure that the grill pan is p
32. is appliance can be converted for use on another gas gt In the UK the cooker must be installed in accordance with All relevant British Standards Codes of Practice in particular BS 5440 For Natural Gas BS6172 and BS 6891 For LP Gas BS 5482 1 when the installation is in a permanent dwelling BS 5482 2 when the installation is in a caravan or other non permanent dwelling or BS 5482 3 when the installation is in a boat The Gas Safety Installation and Use regulations The relevant Building IEE regulations In the Republic of Ireland the cooker must be installed in accordance with The installation must be carried out by a competent person and installed in accordance with the current edition of IS813 Domestic Gas Installations the current Building Regulations and reference should be made to the current ETCI rules for electrical installation Provision of Ventilation This appliance is not connected to a combustion products evacuation device Particular attention shall be given to the relevant requirements regarding ventilation All rooms require a window that can be opened or equivalent while some rooms require a permanent vent in addition to the window In the UK The room containing the cooker should have an air supply in accordance with BS 5440 Part 2 All rooms require an openable window or equivalent while some rooms require a permanent vent in addition to the openab
33. king Keep babies and children away from the cooker and never wear loose fitting or hanging clothes when using the appliance A DO NOT usea steam cleaner on your cooker Always be certain that the controls are in the OFF position when the oven is not in use and before attempting to clean the cooker When the oven is on DO NOT leave the oven door open for longer than necessary otherwise the control knobs may become very hot When using the grill make sure that the grill pan is in position and pushed fully in otherwise the control knobs may become very hot Always keep combustible materials e g curtains and flammable liquids a safe distance away from your cooker DO NOT spray aerosols in the vicinity of the cooker while it is on Use dry oven gloves when applicable using damp gloves might result in steam burns when you touch a hot surface Do not use a towel or other bulky cloth in place of a glove it might catch fire if brought into contact with a hot surface A NEVER operate the cooker with wet hands A DO NOT use aluminium foil to cover shelves linings or the oven roof A DO NOT use hotplate protectors foil or hotplate covers of any description These may affect the safe use of your hotplate burners and are potentially hazardous to health A NEVER heat unopened food containers Pressure build up may make the containers burst and cause injury A DO NOT use unstable saucepans Always make sure that you
34. l Islands and Isle of Man OUT OF WARRANTY Service work should only be carried out by technically competent and suitably qualified personnel For your own safety always make sure that work is carried out by a Gas Safe registered engineer for gas appliances or an approved electrician for electrical models For a competitive quote and to arrange for a Rangemaster approved engineer to attend call Consumer Services on 0870 7895107 SPARE PARTS To maintain optimum and safe performance we recommend that only genuine Rangemaster spare parts are used These are available from most major spares stockists including ourselves Contact Consumer Services on 0870 7895107 who will be happy to help STANDARDS Rangemaster cookers are designed and manufacturedtoa 1 recognised international quality standard which meets the requirements of BS EN ISO 9001 BS EN ISO 14001 and OHSAS 18001 for continually improving environmental procedures Rangemaster cookers comply with the essential requirements of the appropriate European Directives and carry the CE mark ALSO PART OF THE RANGEMASTER COLLECTION Dishwashing Clarence Street Royal Leamington Spa Warwickshire CV31 2AD England Tel 44 0 1926 457400 Fax 44 0 1926 450526 E mail consumers rangemaster co uk Consumer Services Tel 44 0 870 7895107 www rangemaster co uk For ROI Enquiries Tel 1850 302 502 Ei Search Rangemaster UK Built in Cooking Sinks
35. le window The cooker should not be installed in a bedsitting room with volume less than 20 m If it is installed in a room of volume less than 5 m an air vent of effective area 100 cm is required if it is installed in a room of volume between 5 m and 10 m an air vent of effective area 50cm is required while if the volume exceeds 11 m no air vent is required If there are other fuel burning appliances in the same room BS 5440 Part 2 should be consulted to determine the requisite air vent requirements In the Republic of Ireland Reference should be made to the current edition of I 813 which makes clear the conditions that must be met to demonstrate that sufficient ventilation is available 19 INSTALLATION Check the appliance is electrically safe and gas sound when you have finished Location of Cooker Checking the Parts The cooker may be installed in a kitchen kitchen diner but 4 pan supports Wok cradle NOT in aroom containing a bath or shower This appliance is designed for domestic cooking only Use for any other purpose could invalidate any warranty or x Z liability claim N Note An appliance for use on LPG must not be installed i f e in a room or internal space below ground level e g in a basement Conversion This appliance is supplied set for G20 20 mbar Cat Il5 i43 A conversion kit for another gas is included with the cooker If the appliance is to be converted to another gas we
36. nce from the cooker to nearby surfaces The cooker should not be placed on a base Above hotplate surround should be level with or above any adjacent work surface A gap of 75mm should be left between each side of the cooker ABOVE the hotplate level and any adjacent vertical surface For non combustible surfaces such as unpainted metal or ceramic tiles this can be reduced to 25 mm A minimum space of 650mm is required between the top of the hotplate and a horizontal combustible surface Fig 7 2 shows the suggested clearances above the cooker Any cookerhood should be installed in accordance with the n 1100 mm min hood manufacturer s instructions m Any splashback must be fitted in accordance with the manufacturers instructions Allowance should be made for the 410 mm min flue trim which is fitted to the cooker hob Surfaces of furniture and walls at the sides and rear of the b E 4 de do dP 4 gt dd appliance should be heat splash and steam resistant Certain types of vinyl or laminate kitchen furniture are particularly prone to heat damage and discolouration We cannot accept responsibility for damage caused by normal use of the cooker to any material that de laminates or discolours at temperatures less than 65 C above room temperature n i p a ioi LG
37. ner Lift off a burner head Fit the pressure gauge to the injector Turn on and light one of the other hotplate burners Turn on the control knob for the burner with the pressure gauge fitted to let gas through See the data badge for test pressures Turn off the burners Make sure that you reassemble the burner top in the correct way on the burner body 24 INSTALLATION Check the appliance is electrically safe and gas sound when you have finished Electrical Connection The cooker must be installed by a qualified electrician in accordance with all relevant British Standards Codes of Practice in particular BS 7671 or with the relevant national and local regulations Note The cooker must be connected to the correct electrical supply as stated on the voltage label on the cooker through a suitable cooker control unit incorporating a double pole switch having a contact separation of at least 3mm in all poles A The cooker MUST NOT be connected to an ordinary domestic power point Access to the mains terminal is gained by removing the electrical terminal cover box on the back panel Connect the mains cable to the correct terminals for your electrical supply type Fig 7 13 Check that the links are correctly fitted and that the terminal screws are tight Secure the mains cable using the cable clamp Final Checks Hotplate Check Check each burner in turn refer to the Hotplate Burners section at the front
38. ntle heat good for slow cooking of casseroles in the middle of the oven or for plate warming The Browning and Base Heat functions are useful additions to your oven giving you flexibility to finish off items to perfection The Fan Oven The right hand oven is a fan oven that circulates hot air continuously which means faster more even cooking The recommended cooking temperatures for a fan oven are generally lower than a conventional oven Note Please remember that all cookers vary so temperatures in your new ovens may differ to those in your previous cooker Fig 2 19 Operating the Ovens Operating the Multi function Oven The multi function oven has two controls a function selector and a temperature setting knob Fig 2 18 Turn the function selector control to a cooking function Fig 2 19 shows the control set for convectional oven cooking Turn the oven temperature knob to the temperature required Fig 2 19 The oven heating light will glow until the oven has reached the temperature you selected It will then cycle on and off during cooking as the oven maintains the selected temperature Fig 2 21 Operating the Fan Oven Turn the oven knob to the desired temperature Fig 2 20 The oven indicator light will glow until the oven has reached the temperature selected It will then cycle on and off during cooking Fig 2 21 Accessories Oven Shelves Flat shelf In addition to the flat shelves your
39. of the oven To fit the Handyrack locate one side of it on the door bracket Fig 2 27 Then spring the other side out to clip it onto the other bracket Fig 2 28 Fig 2 22 iu Shelf guard d Fig 2 26 Main Oven Light Press the button to turn the lights on Fig 2 29 If an oven light fails turn off the power supply before changing the bulb See the Troubleshooting section for details on how to change the bulb Storage The bottom drawer is for storing oven trays and other cooking utensils It can get very warm so do not store anything in it that may melt or catch fire To remove the drawer pull it fully forward Fig 2 30 Push the ends of the plastic clips down of the left hand side up on the right hand side to release the catches holding the drawer to the side rails Fig 2 31 At the same time pull the drawer forwards and away from the side rails For safety s sake push the drawer runners back out of the way To refit the drawer pull the side rails fully out Carefully move the drawer back between the rails and rest it on the side rails At each side hold the front of the drawer and pull the side rail forward so that the clips click into position holding the drawer to the side rails Fig 2 32 10 3 Cooking Tips Cooking with a Multi function Oven Remember not all modes are suitable for all food types The oven cooking times given are intended for a guide only
40. on This must be in accordance with the relevant standards The flexible hose not supplied with the cooker must be in accordance with the relevant standards Hoses may be purchased at most builders merchants The gas supply needs to terminate with a down facing bayonet The connector is located just below the hotplate level at the rear of the cooker If in doubt contact your supplier The rear cover boxes limit the position of the supply point Because the height of the cooker can be adjusted and each connection is different it is difficult to give precise dimensions Although a 900 mm hose can be used a 1250 mm hose will allow slightly more flexibility in the positioning of the bayonet and make moving the cooker easier The hose should be fitted so that both inlet and outlet connections are vertical so that the hose hangs downwards in a U shape Ideally the hose supply connection should be within the shaded area A Fig 7 12 For Natural Gas the flexible hose must be in accordance with BS 669 For LP Gas it should be capable of 50 mbar pressure 70 C temperature rise and carry a red stripe band or label If in doubt contact your supplier Screw connect the threaded end of the hose into the gas inlet After completing the gas connection make sure that the Cooker is gas sound with a pressure test Pressure Testing The gas pressure can be measured at the injector of one of the hotplate burners not a wok bur
41. ors 26 z Tap Adjustment 26 4 Cooking Table 12 BE a 5 Cleaning Your Cooker 13 Pressure Testing 27 Essential Information 13 9 Circuit Diagram 28 Hotplate Burners 13 The Griddle 14 10 Technical Data 29 Glide out Grill 14 Control Panel and Doors 15 Ovens 15 Cleaning Table 16 Elise 110 Dual Fuel i U110090 04 1 Before You Start Your cooker should give you many years of trouble free cooking if installed and operated correctly It is important that you read this section before you start particularly if you have not used a dual fuel cooker before Important A This appliance is designed for domestic cooking only Using it for any other purpose could invalidate any warranty or liability claim In particular the oven should NOT be used for heating the kitchen besides invalidating claims this wastes fuel and may overheat the control knobs A This appliance is for use in Great Britain and the Republic of Ireland It is a Cat ll2 434 cooker and is set for G20 at 20 mbar A conversion kit for LPG is supplied with the cooker Installation and Maintenance In the UK the cooker must be installed by a Gas Safe registered engineer The electrical installation should be in accordance with BS 7671 Otherwise all installations must be in accordance with the relevant instructions in this booklet with the relevant national and local regulations and with the local gas and electricity supply companies requirements Make sure
42. our Appliance Serial Number Natural Gas Fuel Type Dual Fuel Retailer s Name amp Address Date of Purchase Installer s Name amp Address Installer s Telephone Number Date of Installation This information is on the appliance data badge look in the appliance instructions to find out where the data badge is located CONSUMER SERVICE If you have any product enquiries or in the event of a problem with your appliance once it has been installed please telephone 0870 789 5107 CONSUMER SERVICE LINES OPEN Monday to Thursday 8am 6pm Friday 8am 5pm Saturday 9am 1pm WARRANTY Your manufacturer warranty covers goods of our own brand for defective workmanship and materials for a period of 1 year from the date of purchase This warranty covers mechanical breakdown and proven cosmetic and manufacturing defects You will receive an additional FREE full 12 months guarantee by registering your purchase using the FREEPOST form provided Alternatively call free on 0800 587 5747 quoting reference RMGX57A or register online at www rangemaster co uk Any damage blemishes or chips identified upon receipt of the product must be reported within 90 days proof of purchase may be required to establish validity Scratches on the surface of ceramic hobs must be reported within 14 days Scratches caused by usage are not covered Accidental damage is not covered by the manufacturer s warranty Fo
43. r warranty compliance the requirements are that the appliance Has been correctly installed in accordance with current legislation relevant British and European Standards and Codes of Practice by a suitably competent person registered with Gas Safe or equivalent body and where applicable a qualified electrician Has been used solely for domestic cooking purposes If in use in the UK has not been taken abroad as a personal export In the Republic of Ireland conditions may vary so consult your retailer Is not second hand or a refurbished appliance The manufacturer s warranty is not transferable Has not been subject to misuse accidental damage or modification and has not deteriorated due to normal domestic wear and tear and the manufacturer s recommendations concerning cleaning materials have been followed Has not been repaired by persons or organisations other than those authorised to act on behalf of AGA Rangemaster Exceptions Items not included under the free 1 year guarantee include pan supports griddles wok rings baking trays grill pans trivets filters light bulbs and other consumable accessories Any damage caused other than through normal use Breakdowns associated with cooking spillage Cosmetic deterioration deemed to be normal wear and tear This warranty is in addition to your Statutory Rights Onlycertain models can be adapted for use with Mains Gas supplied in the Channe
44. s indicates which burner that knob controls Each burner has a Flame Supervision Device FSD that prevents the flow of gas if the flame goes out When a hotplate control knob is pressed in sparks will be made at every burner this is normal Do not attempt to disassemble or clean around any burner while another burner is on otherwise an electric shock could result To light a burner push in the selected burner control knob and turn it to the high position as indicated by the large flame symbol Fig 2 2 The igniter should spark and light the gas Keep holding the knob pressed in to let the gas through to the burner for about ten seconds If when you let go of the control knob the burner goes out then the FSD has not been bypassed Turn the control knob to the OFF position and wait for one minute before you try again this time making sure to hold in the control knob for slightly longer Adjust the flame height to suit by turning the knob counter clockwise Fig 2 3 On this cooker the low position is beyond high NOT between high and off If a burner flame goes out turn off the control knob and leave it for one minute before relighting it Make sure that the flames are under the pans Using a lid will help the contents boil more quickly Fig 2 4 Large pans should be spaced well apart Pans and kettles with concave bases or down turned base rims should not be used Fig 2 5 Simmering aids such
45. soapy water soft cloth Splashback rear grille Enamel or stainless steel Hot soapy water soft cloth Cream cleaner with care if necessary Control panel Paint enamel or stainless steel Warm soapy water Do not use abrasive cleaners on lettering Control knobs handles amp trims Plastic chrome copper or lacquered brass Warm soapy water soft cloth Brass Brass polish Oven door glass glass lid some models only Oven and Grill Toughened glass Hot soapy water cream cleaner scourer if necessary Part Finish Recommended Cleaning Method Sides floor amp roof of oven NOT COOK amp CLEAN OVEN PANELS see below Enamel Any proprietary oven cleaner that is suitable for enamel CAUTION CORROSIVE CAUSTIC OVEN CLEANERS FOLLOW MANUFACTURER S INSTRUCTIONS Do not allow contact with the oven elements Cook amp Clean oven panels some models only Special enamel that partly cleans itself This surface cleans itself at 200 C and above or the panels can be removed and washed with hot soapy water and a nylon brush Oven shelves Handyrack grill trivet Handygrill rack some models only Chrome An oven interior cleaner that is suitable for chrome Soap filled pad Dishwasher Grill pan meat tin some models only Enamel Hot soapy water Soap filled pad Dishwasher Table 5 1 16 6 Troubleshooting Hotplate ignition or
46. that the gas supply is turned on and that the cooker is wired in and switched on the cooker needs electricity Only a qualified service engineer should service the cooker and only approved spare parts should be used Always allow the cooker to cool and then switch it off at the mains before cleaning or carrying out any maintenance work unless specified otherwise in this guide Peculiar Smells When you first use your cooker it may give off an odour This should stop after use Before using for the first time make sure that all packing materials have been removed and then to dispel manufacturing odours turn all the ovens to 200 C and run for at least an hour Before using the grill for the first time you should also turn on the grill and run for 30 minutes with the grill pan in position pushed fully back and the grill door open Make sure the room is well ventilated to the outside air see Ventilation below People with respiratory or allergy problems should vacate the area for this brief period If You Smell Gas DO NOT turn electric switches on or off DO NOT smoke DO NOT use naked flames DO turn off the gas at the meter or cylinder DO open doors and windows to get rid of the gas DO keep people away from the area affected Call your gas supplier If you are using natural gas in the UK ring the National Grid on 0800 111 999 Ventilation A CAUTION The use of a gas cooking appliance results in the production of
47. tion It may be necessary to reduce the temperature by approximately 10 C for recipes previously cooked in a conventional oven If you wish to preheat the oven wait until the indicator light has gone out before inserting the food Fanned Grilling vvv This function operates the fan whilst the top element 3 is on It produces a more even less fierce heat than a conventional grill For best results place the food to be grilled on a trivet over a roasting tin which should be smaller than a conventional grill pan This allows greater air circulation Thick pieces of meat or fish are ideal for grilling in this way as the circulated air reduces the fierceness of the heat from the grill The oven door should be kept closed while grilling is in progress so saving energy You will also find that the food needs to be watched and turned less than for normal grilling Preheat this function before cooking For best results we recommend that the grill pan is not located on the uppermost shelf Fan Assisted Oven emm This function operates the fan circulating air heated by the elements at the top and the base of the oven The combination of fan and conventional cooking top and base heat makes this function ideal for cooking large items that need thorough cooking such as a large meat roast It is also possible to bake on two shelves at one time although they will need to be swapped over during the cooking time as the heat
48. to check for level Place the cooker in its intended position taking care not to twist it within the gap between the kitchen units as damage may occur to the cooker or the units The front feet and rear rollers can be adjusted to level the cooker To adjust the height of the rear of the cooker use a 13mm spanner or socket wrench to turn the adjusting nuts at the front bottom corners of the cooker To set the front turn the feet bases to raise or lower Fitting the Handrail Using the 2 mm Allen key supplied loosen the 2 retaining screws in the base and side of the handrail support Fit the handrail support onto the locating bosses on the fascia Fig 7 10 Note The handle support should face upwards Push the support back against the fascia and tighten the 2 retaining screws Check that each support is secure Locate the handrail onto the support tabs and using the 2 5mm Allen key supplied tighten the 2 retaining screws in the bottom to secure Fig 7 11 Outer stability bracket Cooker 3mm min Typical wall mounting Retaining screw Fig 7 10 Retaining screw Retaining Screw 23 INSTALLATION Check the appliance is electrically safe and gas sound when you have finished Fig 7 12 All dimensions in millimetres Gas Connecti
49. ushed right back to the back stop when grilling Always grill with the grill compartment door open If there is an installation problem and don t get my original installer to come back to fix it who pays You do Service organizations will charge for their call outs if they are correcting work carried out by your original installer It is in your interest to track down your original installer Food is cooking too slowly too quickly or burning Cooking times may differ from your previous oven Check that you are using the recommended temperatures and shelf positions see the oven cooking guide The oven control settings and cooking times are intended to be used only as a guide Individual tastes may require the temperature to be altered either way to get the results you want The oven is not cooking evenly Do not use a baking tray with dimensions larger than those specified in the section on General Oven Tips If you are cooking a large item be prepared to turn it round during cooking If two shelves are used check that space has been left for the heat to circulate When a baking tray is put into the oven make sure that it is placed centrally on the shelf Check that the door seal is not damaged and that the door catch is adjusted so that the door is held firmly against the seal A dish of water when placed on the shelf should be the same depth all over For example if it is deeper at the back then the ba
50. ustard 160 C B 150 45 60 minutes baking tray recommended is 340 mm Baked sponge pudding 180 C B 170 40 45 minutes x 340 mm This ensures free heat Milk pudding 140 150 C B 130 140 2to3 hours EE MM cooking a two tier load the trays Bread 210 C 200 20 30 minutes should be interchanged Fish Fanned Grilling approximately halfway though the Fillet 190 C B 190 C B 15 20 minutes cooking time Whole 190 C B 190 C B 15 20 minutes per 500g Steak 190 C B 190 C B Steaks according to thickness 12 5 Cleaning Your Cooker Essential Information Isolate the electricity supply before carrying out any thorough cleaning Allow the cooker to cool NEVER use paint solvents washing soda caustic cleaners biological powders bleach chlorine based bleach cleaners coarse abrasives or salt DO NOT mix different cleaning products they may react together with hazardous results All parts of the cooker can be cleaned with hot soapy water but take care that no surplus water seeps into the appliance Remember to switch on the electricity supply before re using the cooker Hotplate Burners The burner heads and caps can be removed for cleaning Make sure they are absolutely dry before replacing them The Single Ring Burners When refitting the burner head make sure that the notch lines up with the electrode or hole in the base Check that the burner head is level and that the cap is fitted centrally on the burner
51. ve the panels Lift each panel upward and slide forward off the support brackets Fig 5 10 Once the panels have been removed the oven enamel interior can be cleaned Refit in the reverse order Fig 5 10 15 Hotplate Part Finish Cleaning Table Cleaners listed Table 5 1 are available from supermarkets or electrical retailers as stated For enamelled surfaces use a cleaner that is approved for use on vitreous enamel Regular cleaning is recommended For easier cleaning wipe up any spillages immediately Recommended Cleaning Method Hob top Enamel or stainless steel Hot soapy water soft cloth Any stubborn stains remove gently with a nylon scourer Ceramic Induction hob Toughened glass Hot soapy water cream cleaner scourer if necessary Griddle plate some models only Non stick surface Allow to cool Wash in hot soapy water Do not use abrasive cleaners scourers Dishwasher Warming zone some models only Outside of Cooker Toughened glass Hot soapy water cream cleaner scourer if necessary Part Finish Recommended Cleaning Method Door door surround and storage drawer exterior Enamel or paint Hot soapy water soft cloth Any stubborn stains remove gently with a liquid detergent Stainless steel E cloth electrical retailers or microfibre all purpose cloth supermarket Sides and plinth Painted surface Hot
52. vet back in place with the food on it slide the carriage back into the grill chamber Make sure that it is pushed right in Accessible parts may be hot when the grill is in use Young children should be kept away The grill pan trivet can be turned over to give two grilling positions Fig 2 17 Do not leave the grill on for more than a few moments without the grill pan underneath it A Never close the grill door when the grill is on The Ovens References to left hand and right hand ovens apply as viewed from the front of the appliance The left hand oven is a multi function oven while the right hand oven is a fan oven The Multi function Oven As well as the oven fan and fan element they are fitted with two extra heating elements one visible in the top of the oven and the second under the oven base Take care to avoid touching the top element and element deflector when placing or removing items from the ovens The multi function oven has 3 main cooking functions fan fan assisted and conventional cooking These functions should be used to complete most of your cooking The browning element and base heat can be used in the latter part of the cooking process to fine tune the results to your particular requirements Use fanned grilling for all your grilling needs and defrost to safely thaw small items of frozen food Table 2 1 gives a summary of the multi function modes The multi function ovens hav
Download Pdf Manuals
Related Search