Operating instructions EasyStart Call, 22 1000 34 01
Contents
1. Ei PLEASE NOTE f the phone number which the EasyStart Call calls is authorised the phone number cannot be suppressed call forwarding must be deactivated the password four digit access PIN 1234 no longer has to be entered The EasyStart Call starts with the main menu f no further entry is made within 30 seconds of the selection of a function then the connection is terminated You can end the announcements by pressing key 1 2 3 or 4 to change into a new function All entries e g password changes temperature heating duration etc can by cancelled by pressing the kkey after which a new entry can be made 2 OPERATION MAIN MENU Vehicle Heaters Technical Documentation 7 If the EasyStart Call is in the main menu the functions and the corresponding keys are announced Function Heating ON Announcement To heat press 1 Action Press the 1 key Note EasyStart Call switches to the heating submenu Page 9 Function Ventilating ON Announcement To ventilate press 2 Action Press the 2 key gt Note EasyStart Call switches to the ventilation submenu Page 13 Only possible for heaters with ventilation function Function Change password four digit access PIN Announcement To change your password press 3 Action Press the 3 key Announcement Please enter your new password Action Enter 4 digits and confirm with the key Announcement2. Announcement The interior temperature is minus XX degrees gt Note If the EasyStart Call is set to F degrees Fahrenheit you hear the following announcement if the interior temperature exceeds 120 F Announcement The interior temperature is higher than 120 degrees Note If desired change the temperature unit from F to C via SMS see installation instructions 2 OPERATION SUBMENU VENTILATING Immediately after activating the main menu function Ventilating ON you hear one of the following announcements depending on heater type Vehicle Heaters Technical Documentation 13 Air heater with ventilation duration limit or water heater Announcement Ventilating ON The remaining ventilating duration is XX minutes Air heater in continuous Announcement operation Ventilating ON Continuous operation is set ADDITIONAL FUNCTIONS ARE ANNOUNCED Function Ventilating OFF Announcement To end the ventilating press 1 Action Press the 1 key Note The heater is switched off The EasyStart Call is again in the main menu Function Change ventilating duration Announcement To change the ventilating duration press 3 Action Press the 3 key Announcement Please enter the ventilating duration Action Enter ventilating duration in minutes adjustment range 10 120 minutes for continuous ventilating enter 999 Confirm the action with the key gt Note Input t
3. Duration e g 30 minutes Time span 3 00 PM to 3 05 PM The current time is within the time span the heater is switched on duration e g 30 minutes 20 VEHICLE HEATERS TECHNICAL DOCUMENTATION 2 OPERATION Function SMS command symbol for space Note Input options Program timer pin 1234 T on time mode fan UT Entry 1 2 3 fortimer 1 2 or 3 Entry e g FR 06 30 for Friday 6 30 a m Day of the week entry MO TU WE TH FR SA SU The days of the week can be entered individually or in day ranges e g MO FR SA SU MO SU Only one day range can be entered ata time The abbreviations for the days of the week are in English Time entry Single digit hours and minutes 1 9 or 01 09 The time is factory set to departure time end Entry of duration A value between 10 and 120 minutes can be entered Continuous operation is not available as a pre selection via the timer For note on the heater error message ErR see page 27 The Heater Error Message function must be activated see installation instructions Heater feedback e g T1 on time FR 06 30 mode fan run 45 Heater error message e g time not valid ErR DeviceTime time not set T2 off Vehicle Heaters Technical Documentation 21 2 OPERATION Function SMS command symbol for space Heater feedback Vote Input options Entry example 1 on timer programming e g pin 12
4. Please enter new password again Action Enter your 4 digits and confirm with the key Announcement Password saved gt Note If the entry is incorrect you hear the announcement Announcement Incorrect input Please enter your new password Action Enter your 4 digits and confirm the action with the key Announcement Please enter new password again Action Enter your 4 digits and confirm the action with the key Announcement Password saved 8 VEHICLE HEATERS TECHNICAL DOCUMENTATION Function Read out interior temperature Note To request the interior temperature the room temperature sensor must be connected Announcement To read out the interior temperature press 4 Action Press the 4 key Announcement The interior temperature is XX degrees gt Note If the EasyStart Call is set to F degrees Fahrenheit you hear the following announcement if the interior temperature exceeds 120 F Announcement The interior temperature is higher than 120 degrees Note If desired change the temperature unit from F to C via SMS see installation instructions E PLEASE NOTE After activating the main menu function Heating ON or Ventilating ON the corres ponding submenu is active and you can call up additional functions Vehicle Heaters Technical Documentation 9 2 OPERATION SUBMENU HEATING Immediately after activating the main menu function Heating ON yo
5. SMS command symbol for space Note Input options Heating ventilating OFF pin 1234_heater off Heater feedback Heater off Heater status readout pin 1234_heater For notes on heater error messages ErD ErH and ErC see page 27 The Heater Error Message function must be activated see installation instructions e g Heater on or off mode heater or fan run 45 SP 24 for air heaters only Possible heater error messages no communication ErD HeaterCom lost Heater off heater error ErH HeaterError error with EasyStart Call e g ErC Temp missing NOTES ON TIMER PROGRAMMING When programming a timer you must note the operating modes of the EasyStart Call and if applicable the day range Departure time mode factory setting In departure time mode end if the timer is activated the heater is switched off when the set time is reached Start time mode In start time mode start if the timer is acti vated the heater is switched on when the set time is reached 2 OPERATION Day of the week entry Days of the week can be programmed indi vidually or as a day range You can select from the following day ranges MO FR SA SU MO SU If a timer is activated with a programmed day range all days of the week are always pro cessed in succession Example If during the programmed day range MO FR the timer is activated on Wednesday outside the programmed ti
6. The Ebersp cher heater installed in your vehicle is controlled remotely via telephone with DTMF data transmission or via SMS in a simple and easy manner All mobile and landline telephones that allow multi frequency dial tones DTMF or an SMS to be sent can be used as control units Depending on the heater connected it is pos sible to choose between heating and ventilat ing modes Preselected heating mode timer program ming is only possible via SMS The interior temperature can be requested and displayed by installing the temperature sensor Vehicle Heaters Technical Documentation 3 SAFETY INFORMATION A DANGER Pacemakers and hearing aids can be affected by radio waves and their function disrupted gt Get your doctor to check your pacemaker or hearing aid specialist to check your hearing aid for susceptibility to faults SIM card SIM card holder and accessories are small components and could be swallowed by children risk of death gt Do not allow children access to the small components of the EasyStart Call A CAUTION When EasyStart Call is placed into operation all data on the SIM card are deleted GENERAL INFORMATION To operate the EasyStart Call a SIM card from a mobile telephone network operator is required this is not included in the scope of supply For additional information on the SIM card please see the installation instructions Before starting up the EasyStart Call ca
7. F 97 F Confirm the action with the key 2 OPERATION Function Announcement Vehicle Heaters Technical Documentation 11 Change heating duration To change the heating duration press 3 Action Press the 3 key Announcement Please enter the required heating duration Action Enter heating duration in minutes adjustment range 10 120 minutes for continuous operation enter 999 Confirm the action with the key Note Input two digit time entry 10 99 Input three digit time entry 100 120 Announcement Heating duration XX XXX minutes saved or Continuous operation is set Note For water heaters the continuous operation function is blocked Only a two or three digit time entry 10 99 or 100 120 may be set for the heating duration A one digit 1 9 or incorrect entry results in the following announcement Announcement Incorrect input Please enter the required heating duration Action Enter heating duration in minutes adjustment range 10 120 minutes for continuous operation enter 999 Confirm the action with the key 12 VEHICLE HEATERS TECHNICAL DOCUMENTATION Function Query interior temperature Heating ON is activated Note To request the interior temperature the room temperature sensor must be connected Announcement To read out the interior temperature press 4 Action Press the 4 key
8. is configured When you activate the button while using tone dialling DTMF the heater error message is sent to the authorised phone number the authorised phone number must be configured or when an SMS command is sent the heater error message is sent to the last phone number dialled Malfunction EasyStart Call does not react to calls Vehicle Heaters Technical Documentation 27 DISPLAYS AND MALFUNCTIONS FAULTS The EasyStart Call has been developed to the latest state of the art standards and operates very reliably Displays and malfunctions are usually caused by the SIM card the network operator poor reception low network coverage or incorrect use See the following table for solutions to these problems E PLEASE NOTE If you experience problems with SIM cards of the latest development generation please contact your network operator Cause of error Remedial action No network SIM card has expired or has been deactivated by the network operator SIM card not yet activated for activation see installation instructions Insert the SIM card into the mobile phone and check it Contact network operator or top up prepaid card Start heater via button wait approx 3 min and then call the EasyStart Call again 28 VEHICLE HEATERS TECHNICAL DOCUMENTATION 3 DISPLAYS AND MALFUNCTIONS Malfunction EasyStart Call does not react to SMS Cause of error Remedial act
9. 34 t1 on time TU 06 30 T1 0n time TU 06 30 mode heater Entry run 45 SP 24 for air heaters only pin 1234 for password and space ti for timer 1 on to activate heater operating mode heat time TU 06 30 Departure time Tuesday 6 30 a m The previous entries for duration run and tem perature sp remain valid Entry example 2 on timer programming e g pin 1234 t2 on time MO FR 16 30 mode fan T2 on time MO FR 16 30 mode fan run 40 run 40 Entry pin 1234 for password and space t2 for timer 2 on to activate heater time MO FR 16 30 Start time Monday Friday 16 30 p m mode fan for operating mode ventilation run 40 for ventilating duration 40 minutes The start time for the heater is factory set to departure time end The start time start must be configured see installation instruc tions 22 VEHICLE HEATERS TECHNICAL DOCUMENTATION 2 OPERATION Function SMS command symbol for space Note Input options Entry example 3 on timer programming pin 1234 t3 on time WE05 50 Entry pin 1234_ for password and space 13 for timer 3 on to activate heater operating mode heat time WE 05 50 Departure time Wednesday 5 50 a m The previous entries for duration run and tem perature sp remain valid Heater feedback e g T3 on time WE 05 50 mode heater run 45 SP 24 for air heaters only Activate timer pin 1234 t on Entry 1 2 3 fortimer 1 20r 3 Acti
10. CT FUNCTION AND SEND VIA SMS You received a phone number for the EasyStart Call from your network operator when you acquired the SIM card With an SMS you can turn the heater ON and OFF save 3 preselected times preselect the heating mode within 7 days confirm the input command with SMS feedback for settings see installation instructions Select the desired function from the ones listed see from page 16 and send the appropriate input command via SMS to the EasyStart Call If Heater Feedback was activated in the default settings for the customer the EasyStart Call sends a text message back as confirmation fa text message command contains a status request e g heater a text mes sage is also sent back even if the Heater Feedback function is deactivated Vehicle Heaters Technical Documentation 15 EasyStart Call error messages are only sent if the Heater Error Message func tion is activated on switching on via the voice menu or buttons they are sent to the authorised phone number and on switching on via text message they are sent back to the sender s phone number The Heater Feedback and Heater Error Message functions are deactivated in the factory settings a PLEASE NOTE Both upper and lower case letters are accepted You must always leave an empty space between the password four digit access PIN and the input command In the follow ing overv
11. ERS TECHNICAL DOCUMENTATION 2 OPERATION OPERATE EASYSTART CALL VIA TONE DIALLING DTMF Landline or mobile phone Set your landline telephone to tone dialling DTMF For information on this please refer to the operating instructions for your tel ephone For mobile phones this function is usually pre set CALL EASYSTART CALL You received a phone number from your network operator when you acquired the SIM card This is the phone number of your EasyStart Call Use the landline mobile phone to dial the phone number of your EasyStart Call After the connection is established you hear the greeting text Ebersp cher EasyStart Call Welcome followed by the request Please enter your password Enter the password four digit access PIN and then press the pound key to confirm The password four digit access PIN is factory set to 1234 Password entry four digit access PIN correct If the password four digit access PIN is entered correctly the announcement Main menu occurs and the available commands max 2 repetitions are listed or the currently activated function is stated Password entry four digit access PIN incorrect If the password four digit access PIN is entered incorrectly you hear the announcement Incorrect input fol lowed by the request Please enter your password If the password four digit access PIN is entered incorrectly 3 times in a row then the connection is dropped
12. VEHICLE HEATERS TECHNICAL DOCUMENTATION OPERATING INSTRUCTIONS EASYSTART CALL TELEPHONE REMOTE CONTROL FOR EBERSP CHER PARKING HEATERS AW A WORLD OF COMFORT Ebersp cher 2 VEHICLE HEATERS TECHNICAL DOCUMENTATION CONTENTS CHAPTER TITLE CONTENT PAGE 1 INTRODUCTION Dear Customer 3 Use 3 Safety information 3 General information 3 Notes on smartphone apps 5 2 OPERATION Operate EasyStart Call via tone dialling DTMF 6 all EasyStart Call 6 Main menu 7 Submenu Heating 9 Additional functions are announced 9 Submenu Ventilating 13 Additional functions are announced 13 Operate EasyStart Call via SMS 15 Select function and send via SMS 15 Overview of the functions 16 Notes on timer programming 18 Notes on timer activation 19 Pre adjustments by the customer 24 Manually set the day of the week and the time 25 Control using the button 26 3 DISPLAYS AND MALFUNC TIONS Note on heater error feedbacks ErD ErH ErC and ErR DE Faults 27 1 INTRODUCTION DEAR CUSTOMER Thank you for purchasing an EasyStart Call telephone remote control With this product you have a convenient and innovative option for controlling your Ebers p cher parking heater These operating instructions supplement the explanations provided by your JE service part ner who installed the heater and once again summarise the functions of the EasyStart Call USE
13. iew a space is denoted by _ f the phone number which the EasyStart Call calls is authorised for authorisation see installation instructions the password four digit access PIN does not need to precede the input command A space must be entered between the input commands to separate them The day of the week and the time must be reset after every interruption of the power supply You must manually change the time from summer time to winter time and vice versa 16 VEHICLE HEATERS TECHNICAL DOCUMENTATION 2 OPERATION OVERVIEW OF THE FUNCTIONS Function SMS command _ symbol for space Note Input options Change password four digit access PIN pin 1234_config set pin Entry of new 4 digit access PIN permitted range of 0000 9999 Heater feedback e g PIN 9876 Display current phone number pin 1234 mainphone MainPhone ok number current phone number Authorise the phone number for operating the EasyStart Call pin 1234 mainphone set number Entry of the current phone number is accepted with the symbol or 00 in the country code e g Germany 49 or 0049 Enter max 24 characters for a phone number MainPhone ok number authorised phone number Accept phone number of SMS sender as authorised phone number pin 1234 mainphone set number mine The current phone number is displayed with the symbol or 00 in the country code e g Germany 49 or 0049 MainPh
14. ion No network SIM card has expired or has been deactivated by network operator SIM card not yet activated for activation see installation instructions Call EasyStart Call if no connection insert the SIM card into the mobile phone and check it charge the pre paid card contact the network operator EasyStart Call does not react to SMS Call the EasyStart Call the connection is made SMS syntax correct Password four digit access PIN correct Duration exceeded with SMS provider dependent Activate heater error message and run the check again Heater does not work although header feed back was received Query the status of the heater pin 1234 heater Vehicle fan is not activated by the heater EasyStart Call is configured for auxiliary heating operation Reset EasyStart Call to factory settings Vehicle Heaters Technical Documentation 29 3 DISPLAYS AND MALFUNCTIONS Malfunction Heater error feedback Fault in data communication between EasyStart Call and heater ErD HeaterCom lost Heater off ErD HeaterCom lost Cause of error Remedial action Auxiliary heater configured as parking heater Try to start again Check installation and configuration Contact your JE service partner ErD HeaterCom no_heater_found Heater was not recognised during initial opera tion Heater cannot be switched on Try starting again Rem
15. me the heater heats or ventilates on Thursday and Friday with the specified settings The heater is not operated on Saturday and Sunday From Monday of the following week operation continues with the set specifications for the programmed day range A CAUTION If you program a weekday range make sure that during this time period the vehicle is not parked in an area where heating is not allowed e g in a garage or at a petrol sta tion Note and follow the additional safety notes in the Technical Description of the heater Vehicle Heaters Technical Documentation 19 NOTES ON TIMER ACTIVATION If the timer is activated the heater is switched on under the following conditions In departure time mode factory setting Current day and pre selection day are identical Current time is within the time span time span departure time minus duration When the departure time is reached the heater is switched off Example Current day Pre selection day TH Current time 6 45 PM Departure time 7 00 PM Duration 30 Minutes Time span 6 30 PM to 7 00 PM The current time is within the time span the heater is switched on and heats for 15 min 6 45 PM to 7 00 PM In start time mode Current day and pre selection day are identical Current time is within the time span time span start time plus 5 minutes Example Current day Pre selection day MO Current time 3 03 PM Start time 3 00 PM
16. ommand and receipt of the feedback can lead to a deviation in the time setting You can compensate for this with an adjusted entry Query time if time set e g pin 1234_DeviceTime DeviceTime ok time FR 06 30 For note on heater error message ErC Heater error message see page 27 if time not set The Heater Error Message function must be ErC DeviceTime time not set activated see installation instructions 26 VEHICLE HEATERS TECHNICAL DOCUMENTATION 2 OPERATION CONTROL USING THE BUTTON The EasyStart Call scope of supply includes a button with an indicator light This button must be installed since it is nec essary for operating the heater The integrated indicator light displays the cur rent operating status The button can be used to manually switch the heater on and off The previous entries for duration and tem perature are valid In addition you can press the button and call the EasyStart Call to reset the password four digit access PIN To do so hold the button down when you are requested to enter the password and simul taneously enter the four digit access PIN 1234 factory setting The EasyStart Call then Switches to the main menu If the heater is running when you press the button indicator light on the heating is Switched off 3 NOTE ON HEATER ERROR FEEDBACKS ERD ERH ERC AND ERR The heater error feedbacks ErD ErH ErC and ErR only occur if ErrorFeedback on
17. on duration in immediate operation is factory set to 30 minutes for a water heater and to continu ous operation for an air heater The heating duration or ventilating duration can be changed and saved A time period from 10 to 120 minutes can be selected Continuous operation is only available for air heaters in immediate operation Continuous operation is not possible when the timer function is used If the heater is switched on the indicator light on the button illuminates If there is a fault on the EasyStart Call or the heater and the heater error message function is configured then an SMS message is sent to the control unit mobile phone fixed line telephone After operating mode ventilation has finished factory setting heating is re activated To request the interior temperature the room temperature sensor must be connected The room temperature sensor is included in the scope of supply It is only possible to change the set temperature with an air heater Vehicle Heaters Technical Documentation 5 NOTES ON SMARTPHONE APPS For even easier operation of the EasyStart Call we offer a smartphone app You can download this app at the iPhone App Store or via Google Play for Android smartphones ver Sion 2 3 or new You can download detailed operating instruc tions for the new app at www eberspaecher standheizungen com under Download Bedienungsanleitungen 6 VEHICLE HEAT
18. one ok number authorised phone number Heating ON pin 1234 heater on The previous entries for duration run and tem perature sp remain valid e g Heater on mode heater run 45 SP 24 for air heaters only 2 OPERATION Function SMS command _ symbol for space Note Input options Ventilating ON pin 1234_heater on mode fan The last entry for duration run remains valid Vehicle Heaters Technical Documentation 17 Heater feedback e g Heater on mode fan run 45 Heater ON with entries for duration and temperature pin 1234 heater on run sp Entry of duration You can enter a value between 10 and 120 minutes or perm for continuous operation Continuous operation is only possible for air heaters Entry of temperature value only for air heat ers Temperature range 8 C 36 C 46 F 97 F Enter single digit temperature values e g 9 correct 09 incorrect Enter double digit temperature values e g 21 correct 021 incorrect e g Heater on mode heater run 45 SP 24 for air heaters only Example Entry for heating continuous operation and tem perature for an air heater pin 1234 heater on run perm sp 24 Entry for heating and duration for a water heater pin 1234_heater on run 30 Heater on mode heater run perm SP 24 Heater on mode heater run 30 18 VEHICLE HEATERS TECHNICAL DOCUMENTATION 2 OPERATION Function
19. ove and then re insert the fuse Run through initial operation again Contact your JE service partner ErL DatCom lost Error in the wiring Contact your JE service partner ErH Heater mode_not_supported Incorrect entry The requested function is not supported by the heater Repeat entry Fault heater ErH Heater Error Fault on the heater Try to start again Contact your JE service partner No temperature display ErC Temp missing Temperature sensor not installed No temperature display although tempera ture sensor installed ErC Temp short_circuit Temperature sensor defective Contact your JE service partner Time and day of week in the EasyStart Call are invalid ErC DeviceTime time_not_set The provider does not support the function Automatic time Manually set the day of the week and the time Headquarters J Ebersp cher GmbH amp Co KG Ebersp cherstra e 24 73730 Esslingen Hotline 0800 1234300 Fax hotline 01805 262624 info eberspaecher com www eberspaecher com Ebersp cher 22 1000 34 01 03 EN 08 2012 Subject to change without notice J Ebersp cher GmbH amp Co KG Printed in Germany
20. refully read through these operating instructions and the Technical Description of your Ebersp cher heater Costs telephone charges are incurred when you make a call and send an SMS and when you receive heater feedback via SMS 4 VEHICLE HEATERS TECHNICAL DOCUMENTATION 1 INTRODUCTION f the EasyStart Call is called in a foreign country additional costs are charged roaming charges f the EasyStart Call is called in the border area with a neighbouring country roaming charges can also be incurred due to overlapping network coverage Note the location of your vehicle with respect to the call setup If this EasyStart Call cannot connect to a GSM network e g the customer parks for a longer period of time in an underground car park the EasyStart Call attempts to connect to the GSM network at continu ously increasing intervals until a connection setup is successful Recommendation When you press the button a connection setup is started duration approx 3 min To prevent excessive discharge of the vehicle battery in preselected heating mode we recommend you set the heating duration according to the trip time Example For a trip time of approx 30 minutes single distance the heating period should be set to 30 minutes PLEASE NOTE The ventilation function is not supported for all heater designs Please note the Technical Description for the heater The heating duration or ventilati
21. ror message no temperature sensor is connected ErC Temp missing 24 VEHICLE HEATERS TECHNICAL DOCUMENTATION 2 OPERATION PRE ADJUSTMENTS BY THE CUSTOMER The EasyStart Call can determine the current time automatically if the provider supports this function Check in advance if your provider supports automatic time by sending an SMS to the EasyStart Call If the automatic time function is not sup ported by your provider the time and day of the week must be set manually Function SMS command _ symbol for space Note Input options Retrieve automatic time pin 1234 devicetime For note on the heater error message ErC see page 27 The Heater Error Message function must be activated see installation instructions Heater feedback e g DeviceTime ok time TU 14 20 Heater error message Automatic time not supported by provider ErC DeviceTime time not set Vehicle Heaters Technical Documentation 25 2 OPERATION Function SMS command symbol for space Heater feedback Note Input options Manually set the day of the week and the time pin 1234 devicetime set time DeviceTime ok time e g FR 06 30 Entry e g FR 06 30 for Friday 6 30 a m Day of the week entry MO TU WE TH FR SA SU Time entry Single digit hours and minutes 1 9 or 01 09 To check you should read out the time and day of the week again since the duration of an SMS sending of the input c
22. u hear one of the fol lowing announcements depending on heater type Air heater with heating duration limit Announcement The set temperature is XX degrees The remaining heating duration is XX minutes Air heater in continuous operation Announcement The set temperature is XX degrees Continuous operation is set Water heater Announcement The remaining heating duration is XX minutes ADDITIONAL FUNCTIONS ARE ANNOUNCED Function Heating OFF Announcement To end the heating press 1 Action Press the 1 key Note The heater is switched off The EasyStart Call is again in the main menu or drop connection as appropriate 10 VEHICLE HEATERS TECHNICAL DOCUMENTATION Function Announcement Change temperature setting only for air heaters To change the set temperature press 2 Action Press the 2 key Announcement Please enter the required temperature Action Enter temperature values temperature range 8 C 36 C 46 F 97 F Confirm the action with the key gt Note Enter single digit temperature values e g 9 correct 09 incorrect Enter double digit temperature values e g 21 correct 021 incorrect If an entry was not correct you hear the announcement Announcement Incorrect input Please enter the required temperature Action Enter temperature values temperature range 8 C 36 C 46
23. vation can only be carried out for the selected timer For note on the heater error message ErR see page 27 The Heater Error Message function must be activated see installation instructions T e g 2 on time FR 16 30 mode fan run 40 SP 24 for air heaters only Heater error message e g time not valid ErR DeviceTime time not set T2 off Deactivate timer pin 1234 t off Entry 1 2 3 fortimer 1 2 or 3 Deactivation can only be carried out for the selected timer e g T2 off 2 OPERATION Function SMS command _ symbol for space Note Input options Query status timer 1 2 or 3 pin 1234 t Entry 1 2 3 fortimer 1 2or3 Vehicle Heaters Technical Documentation 23 Heater feedback if timer programmed e g T1 on time TU 06 30 mode heater run 45 SP 24 for air heaters only if timer deactivated e g T2 off Read out statuses of all timers pin 1234 tall e g T1 on or off time WE 05 50 mode heater or fan run 45 SP 24 for air heaters only T2 on or off Options as for timer 1 T3 on or off Options as for timer 1 Query interior temperature pin 1234 temp To request the interior temperature the room temperature sensor must be connected For note on heater error message ErC see page 27 The Heater Error Message function must be activated see installation instructions e g Temp ok value 28 Heater er
24. wo digit time entry 10 99 Input three digit time entry 100 120 Announcement Ventilating duration XX XXX minutes saved Or Continuous operation is set 14 VEHICLE HEATERS TECHNICAL DOCUMENTATION 2 OPERATION Function Note Change ventilating duration Only a two or three digit time entry 10 99 or 100 120 may be set for the ventilation duration A one digit 1 9 or incorrect entry results in the following announcement Announcement Incorrect input Please enter the ventilating duration Action Enter ventilating duration in minutes adjustment range 10 120 minutes for continuous ventilating enter 999 Confirm the action with the key Function Note Query interior temperature Ventilation ON is activated To request the interior temperature the room temperature sensor must be connected Announcement To read out the interior temperature press 4 Action Press the 4 key Announcement The interior temperature is minus XX degrees Note If the EasyStart Call is set to F degrees Fahrenheit you hear the following announcement if the interior temperature exceeds 120 F Announcement The interior temperature is higher than 120 degrees Note If desired change the temperature unit from F to C via SMS see installation instructions 2 OPERATION OPERATE EASYSTART CALL VIA SMS Landline or mobile phone SELE
Download Pdf Manuals
Related Search