Hochiki TCH-B100 - ASX Programmer Operating Instructions
Contents
1. a battery check message will be displayed followed by the address of the Sensor fitted previously un programmed Sensors will read 127 LI Select the required address by incrementing the programmer display left grey key 10 s right grey key units Whilst the display is showing an address different to that stored in the Sensor 3 dots will also flash Once the wanted address is displayed press the upper red key to store the address in the sensor Once the address is correctly stored the 3 dots will cease to flash and the display will show the address set To program a CHQ BS the enclosed lead must be used firstly connect the plug in to the remote programming socket and connect the black croc clip to the C terminal and the red croc clip to the L terminal on the base sounder The address can now be programmed as described above Please note that when programming CHQ BS the maximum address permissable is 254 CHQ BS Control Panel instructions should be checked for address range Operation Analogue Level Reading If the Sensor is an AIC E AIE E then the analogue reading should be ignored for the first 30 seconds until the device stabilises To read the analogue level of a Sensor a Locate the Sensor on the programmer and switch on as described in the previous section a Press the middle red key an A for analogue value will be displayed followed by the analogue value of the Sensor which will be constantly updated for up to 32. minutes or until the right grey key is pressed to switch the unit off Remote Programming Socket The remote programming socket allows the user to program other ESP devices that contain the EEPROM technology such as Loop powered sounders CHQ BS The Jack socket is wired as the diagram below Programming Socket Programming Lead Red Clip to L Loop Loop VE aa J lt o e Sa Black Clip toc 7 Caution a Only to be used with the ASX Programmer and Hochiki loop devices a Do not short croc clips together a Remove from programmer when not in use Ancillary Functions In addition to the main functions the TCH B100 may display the following messages If displayed on subsequent power on a low battery voltage should be suspected this facility will operate with sufficient life in the battery for approximately 3000 address setting operations left Attempting to program an address greater than 127 Attempting to program an address with no Sensor connected E0 E E2 Cannot find Sensor on power on E3 E4 ES E6 Non valid response from ASX sensor Cannot find a device to program Fail during analogue level reading f HOCHIKI Hochiki Europe UK Ltd reserves the right to alter the specification of its products from time to World Class Leaders in Fire Detection since 1918 Hochiki Europe UK Ltd time without notice Although every effort has Grosvenor Road Gillingham Business P
3. K Hochiki TCH B100 ASX Programmer Operating Instructions oe he oe Remote Con Programming Socket Battery Middle red oust Left grey Key Right grey Key General Description The TCH B100 ASX Programmer is designed for use with the following products ALG E Analogue Photo electric Sensor AIE E Analogue lonisation Sensor ATG E Analogue Heat Sensor ACA E Analogue Multi Sensor CHQ BS Loop Powered Sounder The programmer is used to set the address of the above products for use with Hochiki ESP systems The unit is designed to be light robust and easy to use and operates from a single PP3 size heavy duty battery which gives the capacity for up to 8 000 operations Keys The TCH B100 has 3 operating keys a middle red key and lower left and right grey keys these keys have the following functions E E E Left grey key key Power On automatically reads the address of the fitted sensor subsequent operations of this key will advance the programmer address in units of 10 Right grey key key Advances the programmer address display in units of 1 Also used as the Power Off button Middle red key key Stores the displayed address to the Sensor and is used to read the Sensor s analogue levels Operation Address Setting E E LI Locate the Sensor onto the programmer ensuring the 3 locating pips line up with the grooves in the programmer LI Press the left grey key to switch the programmer on
4. ark been made to ensure the accuracy of the Gillingham Kent ME8 OSA England information contained within this document it is imi Hochiki E Telephone 44 0 1634 260133 Facsimile 44 0 1634 260132 Ree S PN Ea Email sales hochikieurope com description Please check our web site for the Web www hochikieurope com latest version of this document
Download Pdf Manuals
Related Search