English R3 Operating Instructions
Contents
1. button a short 3 second tone will sound to confirm deactivation and OPEnd will appear in the display 10 Battery Life 1 year 3 times a day Battery replacement is required when 1 LObAtt appears in display accompanied by a short one second warning tone 2 Correct code is entered but lock will not open 3 Even if batteries are completely exhausted the codes are not lost Batteries 4 x 1 5 V AAA Alkaline Batteries are required to activate the lock Used batteries should not be disposed of with normal domestic waste These should be disposed of at approved collection points You may also return used batteries to your Retailer at their expense where applicable2. SAFEX GOMPANY LIMITED Battery Installation 4 x LRO3 AAA Alkaline Supplied Keypad and LCD Display Window 888908 ff ee h I acto ih w 25 885 LED h wad Yeh J Battery Position under Keypad C Button Button Start Button 1 First Opening on Factory Default Code Step 1 Press C button Step 2 Press factory code 123456 Step 3 Press button a melodic tone will sound and the display confirms OPEnd Step 4 Turn Knob or Handle clockwise and open the door while the tone is sounding Caution If an incorrect code is entered Error will appear in the display panel and a short warning tone will sound If an incorrect code is entered five times the lock will cease to operate for five minutes a warning tone will sound and the display will indicate dELAY O 000000 QOG 2 setting a New Personal Code It is advisable to set a new code with the door open and test the new code before closing the door Step 1 Press button Step 2 Enter the Present Code Step 3 Press button Step 4 Enter New 4 16 digit Code Step 5 Press button For Example lf the present code is 1 2 3 4 5 6 and a new four digit code is decided as 4 2 4 2 press buttons as below 123456 4242 EnTErd will be indicated in the display and a short 3 second tone will sound to confirm the change to 4 2 4 2 O CED gt Q CID G Opening Battery Compartment Upper Lower 1 Remove keypad M ret
3. aining screw 2 Press the keypad opening mark to release the retaining arm and swing the keypad up and left to open 3 Setting the dual control function where two operators with individual personal codes are required to open the lock With the door in the open position set the second code Step 1 Press the M memory button recessed into the back of the door Step 2 Press 2 button Step 3 Press button Step 4 Enter 2nd Personal code Step 5 Press button EnTErd will be indicated in the display and a short 3 second tone will sound to confirm the 2nd code entry For Example If the present code is 4 2 4 2 and a second new four digit code is decided as 6 7 8 9 press buttons as below EnTErd will appear in the display accompanied by a short tone to confirm M2 6789 O O gt QG Erp 4 To Activate Dual Control Step 1 Press the M memory button recessed into the back of the door Step 2 Press 9 button Step 3 Press button 5 To operate with the dual control function Step 1 Press C button dual will appear in the display Step 2 Enter the first code 4 2 4 2 Step 3 Press button a short 3 second tone will sound to confirm correct code Step 4 Within 5 minutes enter the second code 6 7 8 9 Step 5 Press button a short 3 second tone will sound to confirm correct code and OPEnd will appear in the display and the lock will be open Either code can be entered
4. first or second ap CE Sy Nt a CLO VIN OLY 6 To deactivate dual control Step 1 Press the M memory button recessed into the back of the door Step 2 Press 9 button Step 3 Press button a short 3 second tone will sound to confirm deactivation and SinGLE will appear in the display The second code will be automatically erased 7 To hide code in the display and turnoff keypad sound Activate Press the M memory button recessed into the back of the door gt EP HdE appears in the display Deactivate Press the M memory button recessed into the back of the door gt 8 To hide code entry in a number sequence The code can be disguised by inserting random numbers either before after or both before and after the personal code This procedure is designed to increase security and to confuse a potential observer attempting to memorise the code This feature can be also be used with hidden code display and silent keypad as at 7 above For Example Personal code is set as 4 2 4 2 Random prefix numbers 61 Random suffix numbers 91507 Step 1 Press C button Step 2 Enter Code as 61 4 2 4 2 91507 Step 3 Press button The display will confirm OPEnd 9 Alarm setting Activate Press the M memory button recessed into the back of the door D ED ALErT appears in the display Deactivate Step 1 Press C button Step 2 Enter Personal Code Step 3 Press
Download Pdf Manuals
Related Search