OpeRATing insTRuCTiOns eAsysTART TiMeR
Contents
1. VEHICLE HEATERS TECHNICAL DOCUMENTATION OPERATING INSTRUCTIONS EASYSTART TIMER OPERATING INSTRUCTIONS CONTROL UNIT FOR EBERSP CHER PARKING HEATERS AW A WORLD OF COMFORT Ebersp cher 2 VEHICLE HEATERS TECHNICAL DOCUMENTATION CONTENTS CHAPTER CHAPTER TITLE CHAPTER CONTENTS PAGE 1 INTRODUCTION Please read first 4 Safety information 4 Range of uses 4 General information 4 2 OVERVIEW EasyStart Timer 5 Button functions 5 Longpress button 5 Go Shortpress button 5 Li mj Longpress button 5 m Shortpress button 5 Press E button 1x keep pressed 5 Press EI button 1x keep pressed 5 3 OPERATION AND SETTING ADJUSTMENT Notes on operation and setting 6 Factory setting 7 Main menu 8 Start display after switching on 9 Displays for activated menu items 9 Heating immediately with Longpress without settings 10 HEATING OFF with Longpress 10 HEATING ON with Shortpress and with settings 11 HEATING Off with Shortpress 12 VEHICLE HEATERS TECHNICAL DOCUMENTATION 3 Change the temperature setpoint and or the operating time during operation 12 Set VENTILATION ON with Shortpress and if applicable set the operating time 14 VENTILATION OFF with Longpress 15 VENTILATION OFF with Shortpress 15 ADD ON UNIT ON e g activate the HEATING function for a 2nd heater 16 ADD ON UNIT ON e g activate the VENTIL2. FOR AIR HEATERS ONLY Use the EJ or ES button to set the temperature setpoint Temperature setpoint setting range 8 C 36 C in 1 C increments 46 F 97 F in 1 F increments slo 2 i Press the button to confirm the temperature setpoint SETTING THE OPERATING TIME Use the I or E button to set the operating time Operating time setting range Min 10 max 120 min in 1 min increments continu ous heating mode is possible for air heaters l2 r l gt Press the button to confirm the operating time The operating time is changed permanently Heater ON sl gt 2485 e VEHICLE HEATERS TECHNICAL DOCUMENTATION 17 3 OPERATION AND SETTING ADJUSTMENT Display for air heaters in continuous heating mode factory setting S F ile E PLEASE NOTE After switching on On is displayed for 2 sec and then the remaining operating time or CXO for air heaters During heating mode it is possible to switch to another menu item Under the VENTILATION menu item check the operating time and if necessary adjust If the Ap symbol is not displayed the ADD ON UNIT function is not activated or is not available for the heater The add on unit e g a 2nd heater can be operated simultaneously with the 1st heater yet with a differ ent operating mode and with different values for the temperature setpoint and the operating time The changed operating time is offered again the next
3. The operating time can be set using the Bj or DA button Setting range of the operating time min 10 max 120 minutes the input is made in 1 min intervals Continuous heating mode is additionally possible for air heaters The operating time for a heater and for an add on unit can be set independently of each other VEHICLE HEATERS TECHNICAL DOCUMENTATION 7 3 OPERATION AND SETTING ADJUSTMENT NOTES ON OPERATION AND SETTING EXTENDING THE OPERATING TIME The operating time can be extended to up to 720 min the input is made from the 120th min in 5 min inter vals To do this contact the installation workshop VENTILATION OPERATING MODE VENTILATION mode is not possible with all heater types see the Technical Description of the heater for details TEMPERATURE SENSOR In the settings and operations described in the fol lowing it is assumed that a temperature sensor is connected for a water heater In the case of air heaters the temperature sensor installed in the heater and which is provided for con trol of the heater can also be used to determine the interior temperature ADD ON UNIT An add on unit can be e g a second heater or park ing air conditioning Further it is also possible to combine a heater with a fan the fan is then used for air distribution in the vehicle interior A heater and the add on unit can be operated simul taneously or independently of each other E PLEASE NOTE The number of sy
4. SET THE TIME symbol Q is displayed Use the BJ or E button to select the Mo j Week day symbol sl Z jS Press the E button to confirm the setting Use the El or E button to select the weekday sl Press the E button to confirm the weekday E PLEASE NOTE Do not press the E button as otherwise SET THE WEEKDAY appears in the display again After making the setting press the E button to return to the SETTINGS menu item or wail until jf the vehicle lighting is ON the SETTINGS menu item is displayed jf the vehicle lighting is OFF the display lighting goes out 28 VEHICLE HEATERS TECHNICAL DOCUMENTATION SETTING THE TIME FORMAT Display ON the Start display appears Use the BJ or ES button to select the symbol in the Menu bar Zz sl sla Press the E button to confirm the time format zw ES PLEASE NOTE Do not press the button as otherwise SET THE TIME FORMAT appears in the display again Confirm the SETTINGS menu item by pressing the After making the setting press the E button to return to the SETTINGS menu item or wail until jf the vehicle lighting is ON the SETTINGS menu item is displayed s A if the vehicle lighting is OFF the display lighting goes out er e o e lt gt The SET THE TIME symbol is displayed Use the El or E button to select the 12 TIME FORMAT symbol l2 Zw Press the button to confirm the setti
5. button to set the operating time Operating time setting range Min 10 max 120 min in 1 min increments continu ous VENTILATION mode possible for air heaters Ne AS Press the button to confirm the operating time The operating time is changed permanently wl zi Ins Display for air heaters in continuous VENTILATION mode wl zb E PLEASE NOTE After switching on On is displayed for 2 sec and then the remaining operating time or CXO for air heaters During ventilation mode it is possible to switch to another menu item Under the HEATING menu item check the operating time and if necessary adjust If the E symbol is not displayed the VENTILATION function is not activated or is not available for the heater The changed operating time is offered again the next time the system is started VEHICLE HEATERS TECHNICAL DOCUMENTATION 15 3 OPERATION AND SETTING ADJUSTMENT VENTILATION OFF WITH LONGPRESS Display ON the VENTILATION menu item is displayed Press the LONGPRESS button for longer than 2 seconds Heater OFF slo fis After the VENTILATION OFF display the Start display appears If the vehicle lighting is OFF the display lighting goes out after 10 seconds wl pow PLEASE NOTE With VENTILATION OFF with LONGPRESS all active functions are ended The following actions are possible during the VENTILATION OFF display Use the El or El button to select a men
6. time the system is started ADD ON UNIT ON E G ACTIVATE THE VENTILATION FUNCTION FOR A 2ND HEATER Display ON the Start display appears Use the Ez or Ex button to select the Ap symbol in the Menu bar S F Zip Confirm the ADD ON UNIT menu item by pressing the button Use the Iz or Ex button to select the symbol wl ee noms Confirm the VENTILATION function by pressing the button a PLEASE NOTE The following setting or confirmation is absolutely necessary 18 VEHICLE HEATERS TECHNICAL DOCUMENTATION 3 OPERATION AND SETTING ADJUSTMENT SETTING THE OPERATING TIME Use the J or ES button to set the operating time Operating time setting range Min 10 max 120 min in 1 min increments continu ous VENTILATION mode possible for air heaters wl Im A SS Press the button to confirm the operating time The operating time is changed permanently Heater ON sla A gt Display for air heaters in continuous VENTILATION mode factory setting sl o AS BI PLEASE NOTE After switching on On is displayed for 2 sec and then the remaining operating time or CXO for air heaters During ventilation mode it is possible to switch to another menu item Under the HEATING menu item check the operating time and if necessary adjust If the Ap symbol is not displayed the ADD ON UNIT function is not activated or is not available for the heater The add on unit e g a 2nd
7. 73730 Esslingen Hotline 0800 1234300 Fax hotline 01805 262624 info eberspaecher com www eberspaecher com Ebersp cher Ebersp cher Climate Control Systems GmbH amp Co KG Subject to change without notice 06 2013 22 1000 34 15 05 EN
8. ATION function for a 2nd heater 17 ADD ON UNIT OFF with Longpress 19 ADD ON UNIT OFF with Shortpress 19 General information on programming the preset time 20 Program preset times 22 EasyStart Timer settings 22 Settings 26 4 WHAT TO DO IF In the event of a fault the following displays are possible 29 5 SERVICE Hotline 30 4 VEHICLE HEATERS TECHNICAL DOCUMENTATION 1 INTRODUCTION PLEASE READ FIRST Before you start to set and use the timer always read through these operating instructions carefully These operating instructions contain important infor mation that you require for to set and use the timer Please keep these operating instructions in a safe place for subsequent reference SAFETY INFORMATION A DANGER Always note and follow all information and notes especially the safety instructions in this document and in the heater s technical description RANGE OF USES The EasyStart Timer is used to select the operat ing mode to set the operating time to preselect the switching on time and to switch On Off the heater and or add on unit installed in the vehicle E PLEASE NOTE Improper use and use outside the specified area of use cancels all liability and warranty GENERAL INFORMATION The EasyStart Timer has a simple operating structure All functions can be set and if necessary changed with only 4 buttons To use the AUTOMATIC OPERATING TIME CALCULA TION function of a water heater the option
9. J button to select a menu item SHORTPRESS button the Start display appears if the SHORTPRESS button is pressed again Display OFF SHORTPRESS button the HEATING submenu is displayed 20 VEHICLE HEATERS TECHNICAL DOCUMENTATION 3 OPERATION AND SETTING ADJUSTMENT GENERAL INFORMATION ON PROGRAMMING THE PRESET TIME The programming of the preset time is carried out in menu item P The EasyStart Timer can be used to program 3 preset times The 3 preset times can either all take place on one weekday or can be distributed between different weekdays 3 weekday ranges are available to choose from these can each be started daily with a preset time Weekday ranges Sat Sun 2x HEATING VENTILATION Mon Fri 5x HEATING VENTILATION Mon Sun 7x HEATING VENTILATION If the system is activated with programmed weekday range all weekdays are worked through consecu tively after that renewed programming is required Example If the EasyStart Timer with a programmed weekday range Mon Fri is activated on Sunday the heater heats or ventilates from Monday to Friday with the set defaults 5x HEATING VENTILATION If the EasyStart Timer with a programmed week day range Mon Fri is activated on Wednesday the heater heats or ventilates on Thursday and Friday the heater is not operated on Saturday and Sunday From Monday to Wednesday of the following week the operation is continued with the set defaults 5x HEATING VE
10. NTILATION After a weekday range has been worked through renewed programming is required E BITTE BEACHTEN If the P symbol is not displayed in the Menu bar the heater is in ADR mode preselected heating mode is not possible here When programming the EasyStart Timer note the operating mode as described in the following DEPARTURE TIME OPERATING MODE FACTORY SETTING Under the following conditions the preselected heat ing mode is not started on the current day The current day and the preselected day are iden tical The current time lies within the time period depar ture time minus operating time Example Current day preselected day Thu Current time 18 45 Departure time 19 00 Operating time 30 minutes Duration 18 30 to 19 00 The current time lies within the time period the heater is not switched on The program will be run during the next week START TIME OPERATING MODE In Start Time operating mode the heater is started on the preselected day and when the set time is reached VEHICLE HEATERS TECHNICAL DOCUMENTATION 21 3 OPERATION AND SETTING ADJUSTMENT AUTOMATIC OPERATING TIME CALCULATION for water heaters only For water heaters and a temperature sensor con nected to the EasyStart Timer the heating start is calculated automatically depending on the measured room temperature and the selected heating level ECO or HIGH The operating time can lie between 10 and 60 minutes
11. Other possible actions are ADD ON UNIT HEATING OFF see page 19 select a new menu item ADD ON HEATER VENTILATION ON wl N Other possible actions are ADD ON UNIT VENTILATION OFF see page 19 select a new menu item 10 VEHICLE HEATERS TECHNICAL DOCUMENTATION 3 OPERATION AND SETTING ADJUSTMENT HEATING IMMEDIATELY WITH LONGPRESS WITHOUT SETTINGS Press the LONGPRESS button for longer than 2 seconds Heater ON j 444 q ERN Display for air heaters in continuous heating mode factory setting wl ala B PLEASE NOTE After switching on On is displayed for 2 sec and then the remaining operating time or OO for air heaters Set values are copied from the previous heating mode If LONGPRESS is pressed during heating mode the display switches to the HEATING submenu SET TEMPERATURE SETPOINT only for air heater and SET OPERATING TIME During heating mode it is possible to switch to another menu item Under the VENTILATION menu item check the operating time and if necessary adjust HEATING OFF WITH LONGPRESS Display ON the HEATING menu item is displayed Press the LONGPRESS button for longer than 2 seconds Heater OFF Eu Zu After the HEATING OFF the Start display appears If the vehicle lighting is OFF the display lighting goes out after 10 seconds sle eo E PLEASE NOTE With HEATING OFF with LONGPRESS all active func tions are ended The fo
12. ally avail able temperature sensor must be used If a vehicle was without a power supply battery dis connected and the power supply is restored INIT for automatic heater detection appears in the display of the EasyStart Timer If the detection was successful the time is displayed flashing in the start display The time must be set Then the weekday must be set see page 26 Use of the EasyStart Timer is described in detail from page 6 2 OVERVIEW EASYSTART TIMER The EasyStart Timer can be used to make the neces sary settings for operation of the heater and or the add on unit BUTTON FUNCTIONS c3 LONGPRESS button The button must be pressed for longer than 2 seconds The heater is switched on immediately if ON or OFF appears in the display except if programming is run ning or while making settings C3 SHORTPRESS button The button must be pressed for less than 2 seconds if the display shows OFF EasyStart Timer ON the Start display appears aselected function is confirmed inputs are confirmed EB LONGPRESS button The button must be pressed for longer than 2 seconds all functions are ended if the display shows OFF gt EasyStart Timer ON the Start display appears VEHICLE HEATERS TECHNICAL DOCUMENTATION 5 EB SHORTPRESS button The button must be pressed for less than 2 seconds the displayed activated function is ended other activated functions are re
13. ars in the display then continue with the operation or setting ACTIVATING A MENU ITEM The symbol of the menu item to be activated appears in the middle and flashing in the display In the case of several activated menu items the symbols are displayed alternately DISPLAY The display is lit during use of the EasyStart Timer if terminal 58 is connected with switched on vehi cle lighting jf the heater add on heater is ON DISPLAY DISAPPEARS If the vehicle lighting is switched off no heater or add on unit is switched on or if no setting or actua tion is made the display goes out within 10 seconds i e the EasyStart Timer switches to standby For renewed input one of the four buttons must be pressed first not in heating ON with LONGPRESS FLASHING SYMBOL FLASHING VALUE In the Main menu a flashing symbol in the Menu bar is activated with the E button In the submenu a flashing value can be confirmed or a selection made using the Ez or Ej button HEATING ON WITH LONGPRESS The heater is switched on immediately An add on heater is not switched on immediately HEATING OFF WITH LONGPRESS If a heater and an add on unit is in operation both are switched off CANCEL EXIT SETTINGS The setting can be cancelled or exited by pressing the EB button CONFIRM INPUT The settings and changes must always be confirmed by pressing the button otherwise they are lost SETTING THE OPERATING TIME
14. ed as set values The operating time and the temperature setpoint are changed once Both set values must be confirmed SET TEMPERATURE SETPOINT ONLY FOR AIR HEATERS NOT FOR THE VENTILATION FUNCTION Use the BE or E button to set the temperature setpoint Temperature setpoint setting range 8 C 36 C in 1 C increments 46 F 97 F in 1 F increments sl Fis Press the button to confirm the temperature set point The temperature setpoint is changed once VEHICLE HEATERS TECHNICAL DOCUMENTATION 13 SETTING THE OPERATING TIME Use the El or EJ button to set the operating time Operating time setting range Min 10 max 120 min in 1 min increments continu ous heating mode is possible for air heaters Ne fis Press the E button to confirm the operating time The operating time is changed once sl gt Ems Display for air heaters in continuous heating mode wl n 14 VEHICLE HEATERS TECHNICAL DOCUMENTATION 3 OPERATION AND SETTING ADJUSTMENT SET VENTILATION ON WITH SHORTPRESS AND IF APPLICABLE SET THE OPERATING TIME Display ON the Start display appears Use the Ez or Ex button to select the 88 ventila tion symbol in the Menu bar wl a LN Confirm the VENTILATION menu item by pressing the button a PLEASE NOTE The following setting or confirmation is absolutely necessary SETTING THE OPERATING TIME If necessary use the I or uml
15. emperature in the vehicle interior e g 21 C If a menu item is activated heating ventilation add on unit settings or program preselection differ ent information is displayed in the status area this appears and described in the relevant sections SUBMENU Menu bar Ne Input area A DS Display e g HEATING ON Operating time 107 min In the submenu the symbol of the selected menu item appears in the middle of the display The corresponding set value is displayed flashing in the entry area and can be set using the BE or Ej button and confirmed with the button VEHICLE HEATERS TECHNICAL DOCUMENTATION 9 3 OPERATION AND SETTING ADJUSTMENT START DISPLAY AFTER SWITCHING ON Wie pow If no menu item is activated the Start display appears with a flashing heater symbol in the Menu bar with the current time and the actual temperature in the status area Other possible actions are HEATING IMMEDIATELY with LONGPRESS HEATING ON with SHORTPRESS in addition con firm and if applicable set the temperature setpoint and operating time see page 11 Select a new menu item DISPLAYS FOR ACTIVATED MENU ITEMS HEATING ON wl ZI Other possible actions are HEATING OFF see page 10 and 12 Select a new menu item VENTILATION ON wl E Other possible actions are VENTILATION OFF see page 15 select anew menu item ADD ON HEATER HEATING ON wl FIs
16. erating time setting range Min 10 max 120 min in 1 min increments l2 Z S Press the button to confirm the operating time El PLEASE NOTE In the case of water heaters with automatic operating time calculation the operating time is limited to max 65 min The operating time cannot be set For air heaters and preset mode the operating time is limited to 120 min Continuous heating mode is not possible VEHICLE HEATERS TECHNICAL DOCUMENTATION 25 3 OPERATION AND SETTING ADJUSTMENT ACTIVATING THE PROGRAM MEMORY sl Z S Press the button to confirm the On setting vl a fits C PLEASE NOTE After editing the program press the button to return to the PROGRAM PRESELECTION menu item or wail until if the vehicle lighting is ON the PROGRAM PRESE LECTION menu item is displayed if the vehicle lighting is OFF the display lighting goes out Do not press the button as otherwise the On setting switches to Off and vice versa DEACTIVATING THE PROGRAM MEMORY Use the I or Ej button to select the Off setting sl bs Press the button to confirm the Off setting mE PLEASE NOTE The settings remain saved After editing the program press the button to return to the PROGRAM PRESELECTION menu item or wail until jf the vehicle lighting is ON the PROGRAM PRESE LECTION menu item is displayed jf the vehicle lighting is OFF the display lighting goes
17. heater can be operated simultaneously with the 1st heater yet with a differ ent operating mode and with different values for the temperature setpoint and the operating time The changed operating time is offered again the next time the system is started VEHICLE HEATERS TECHNICAL DOCUMENTATION 19 3 OPERATION AND SETTING ADJUSTMENT ADD ON UNIT OFF WITH LONGPRESS Press the LONGPRESS button for longer than 2 seconds Add on unit OFF wl Zi After the ADD ON UNIT OFF display the Start display appears If the vehicle lighting is OFF the display lighting goes out after 10 seconds S ZI E PLEASE NOTE With ADD ON UNIT OFF with LONGPRESS all active functions are ended The following actions are possible during the ADD ON UNIT OFF display Use the Eel or uml button to select a menu item SHORTPRESS button the Start display appears if the SHORTPRESS button is pressed again Display OFF SHORTPRESS button the HEATING submenu is displayed ADD ON UNIT OFF WITH SHORTPRESS Display ON the ADD ON UNIT HEATING menu item is displayed Press the SHORTPRESS button for less than 2 seconds Add on unit OFF sle Z E gt After the ADD ON UNIT OFF display the Start display appears If the vehicle lighting is OFF the display lighting goes out after 10 seconds S Caro Bees Ei PLEASE NOTE The following actions are possible during the ADD ON UNIT OFF display Use the I or E
18. ing operating time or CXO for air heaters During heating mode it is possible to switch to another menu item Under the VENTILATION menu item check the operating time and if necessary adjust The changed operating time is offered again the next time the system is started 12 VEHICLE HEATERS TECHNICAL DOCUMENTATION 3 OPERATION AND SETTING ADJUSTMENT HEATING OFF WITH SHORTPRESS Display ON the HEATING menu item is displayed Press the SHORTPRESS button for less than 2 seconds Heater Off wl fis After the HEATING OFF the Start display appears If the vehicle lighting is OFF the display lighting goes out after 10 seconds RR zi EI PLEASE NOTE The heater switches off an active add on unit remains in operation The following actions are possible during the HEATING OFF display Use the El or ES button to select a menu item SHORTPRESS button the Start display appears if the SHORTPRESS button is pressed again Display OFF SHORTPRESS button the HEATING submenu is displayed CHANGE THE TEMPERATURE SETPOINT AND OR THE OPERATING TIME DURING OPERATION Display ON the HEATING VENTILATION ADD ON UNIT HEATING or ADD ON VENTILATION menu item is displayed Press the SHORTPRESS button for less than 2 seconds E PLEASE NOTE The temperature setpoint set before switching on the heater or confirmed temperature setpoint and the current remaining operating time lower limit 10 min are display
19. llowing actions are possible during the HEATING OFF display Use the IE or E button to select a menu item SHORTPRESS button the Start display appears if the SHORTPRESS button is pressed again Display OFF SHORTPRESS button the HEATING submenu is displayed VEHICLE HEATERS TECHNICAL DOCUMENTATION 11 3 OPERATION AND SETTING ADJUSTMENT HEATING ON WITH SHORTPRESS AND WITH SETTINGS Display ON the Start display appears wl Zip Press the E SHORTPRESS button for less than 2 seconds EN PLEASE NOTE The following settings and confirmations tempera ture setpoint and operating time are always required SET TEMPERATURE SETPOINT FOR AIR HEATERS ONLY If applicable use the BJ or mm button to set the temperature setpoint Temperature setpoint setting range 8 C 36 C in 1 C increments 46 F 97 F in 1 F increments SU 5 AS Press the button to confirm the temperature setpoint SETTING THE OPERATING TIME If necessary use the El or Ej button to set the operating time Operating time setting range Min 10 max 120 min in 1 min increments continu ous heating mode is possible for air heaters slo A 3 Press the button to confirm the operating time Heater ON slo eps Display for air heaters in continuous heating mode factory setting wl ale E PLEASE NOTE After switching on On is displayed for 2 sec and then the remain
20. mbols and displays differs depend ing on the installed heater and feature options FACTORY SETTING PROGRAM PRESELECTION for all heaters Weekday group Mon Fri Departure time 07 00 Language DE Time format 24 h Operating time for preselection preset 30 minutes AIR HEATERS Continuous heating operating time Setpoint temperature 21 C WATER HEATERS Operating time 30 minutes automatic operating time calculation OFF 8 VEHICLE HEATERS TECHNICAL DOCUMENTATION 3 OPERATION AND SETTING ADJUSTMENT MAIN MENU sla Menu bar alas Status area MENU BAR The following menu items can be selected Symbol Function 33 Heating ON OFF s Ap Ventilation ON OFF Add on unit ON OFF e g a second heater ff Settings P Program Preselection E PLEASE NOTE The Ap symbol for the ADD ON UNIT menu item must be activated in the Workshop menu contact the installation workshop The ee symbol for the VENTILATION menu item is now displayed if the heater supports this function Only the m and symbols are displayed in vehi cles in ADR mode If the heater supports the VENTILA TION function the by symbol is also displayed STATUS AREA If no menu item is activated the current time and if an optional temperature sensor is connected the temperature in the vehicle interior are displayed in the status area Start display Time e g 17 30 T
21. ng Use the El or uml button to select the time format xl en VEHICLE HEATERS TECHNICAL DOCUMENTATION 29 IN THE EVENT OF A FAULT THE FOLLOWING DISPLAYS ARE POSSIBLE DISPLAY DESCRIPTION REMEDY CUSTOMER Automatic detection is active The EasyStart Timer has been dis connected from the power supply and then reconnected Wait until the automatic detection has finished then set the time and weekday No communication Check and if necessary renew the heater fuse Visit your vehicle workshop 1st heater fault Visit your vehicle workshop 2nd heater fault Visit your vehicle workshop Voltage too low Charge battery if necessary visit your vehicle workshop Temperature sensor is defective PLEASE NOTE If you are unable to remedy the error or fault please contact an authorised JE workshop or dial the follow ing service phone number Visit your vehicle workshop 30 VEHICLE HEATERS TECHNICAL DOCUMENTATION HOTLINE If you have any technical questions a problem with the EasyStart Timer or the heater dial the following service phone number from within Germany Hotline 0800 1234300 Fax hotline 01805 262624 Outside of Germany please contact the respective Ebersp cher national representative VEHICLE HEATERS TECHNICAL DOCUMENTATION 31 Headquarters Ebersp cher Climate Control Systems GmbH amp Co KG EberspacherstraBe 24
22. operation is always ended 5 minutes after the programmed departure time This can result in a minimum operating time of 15 minutes and a maxi mum operating time of 65 minutes The operating time set in the Program Preselection menu is ineffective in this case In all other configurations the start takes place according to the preset operating time C PLEASE NOTE The ECO and HIGH heating levels are only effective in conjunction with a programmed preset time The preset times are always departure times even if the operating time calculation is deactivated tis not possible to program more than 3 pre set times The max operating time of 65 minutes for the automatic operating time calculation is a factory setting This can be reduced to 15 minutes if nec essary by the installation workshop fthe automatic operating time calculation function is activated for water heaters the operating time for determining the time period is 60 min 22 VEHICLE HEATERS TECHNICAL DOCUMENTATION 3 OPERATION AND SETTING ADJUSTMENT PROGRAM PRESET TIMES Display ON the Start display appears Use the El or EJ button to select the P symbol in the Menu bar Display if no preselection is activated sle 20 Display if a preselection is activated e g P2 je m As Confirm the PROGRAM menu item by pressing the button E PLEASE NOTE If the P symbol is marked with 3 a or several pro gram memories is a
23. out Do not press the button as otherwise the On setting switches to Off and vice versa EDIT THE PROGRAM MEMORY AGAIN Use the J or Ex button to select the X symbol Ne Z s Use the button to confirm the setting and con tinue as described on page 23 24 and 25 26 VEHICLE HEATERS TECHNICAL DOCUMENTATION SETTINGS SETTING THE TIME Display ON the Start display appears Use the IZ or E button to select the symbol in the Menu bar sl PIE Confirm the SETTINGS menu item by pressing the 3 button sl A i3 Confirm the SET THE TIME by pressing the 3 but ton Use the or button to set the hours xl A Ss Press the E button to confirm the setting Use the or button to set the minutes sl dis Press the E button to confirm the setting Ej PLEASE NOTE Do not press the E button as otherwise SET THE TIME appears in the display again After making the setting press the E button to return to the SETTINGS menu item or wail until jf the vehicle lighting is ON the SETTINGS menu item is displayed jf the vehicle lighting is OFF the display lighting goes out VEHICLE HEATERS TECHNICAL DOCUMENTATION 27 SETTING THE WEEKDAY Display ON the Start display appears Use the E or ES button to select the symbol in the Menu bar sl P bes Confirm the SETTINGS menu item by pressing the 3 button Ne din The
24. re already activated Activated program memories are marked in the dis play with a v EASYSTART TIMER SETTINGS SELECTING THE PROGRAM MEMORY The P1 program memory is displayed if applicable use the IE or EJ button to select the next program memory P2 P3 or P1 again Program memory P1 display factory setting vl o AS Program memory P2 display with programmed preselection slo AOS Press the button to confirm the selected pro gram memory ACTIVATING DEACTIVATING THE PROGRAM MEMORY Use the E or E button to select the On or Off setting AN Confirm the On or Off setting with the but ton the program e g P2 is activated or deactivated VEHICLE HEATERS TECHNICAL DOCUMENTATION 23 3 OPERATION AND SETTING ADJUSTMENT E PLEASE NOTE After editing the program press the button to return to the PROGRAM PRESELECTION menu item or wail until if the vehicle lighting is ON the PROGRAM PRESE LECTION menu item is displayed if the vehicle lighting is OFF the display lighting goes out Do not press the button as otherwise the On setting switches to Off and vice versa EDITING THE PROGRAM MEMORY Use the button to confirm the selected program memory e g P2 Use the BJ or E button to select the symbol wl bs Press the button to confirm the setting SELECTING THE WEEKDAY GROUP WEEKDAY Use the I or ES but
25. tained with each SHORTPRESS the display changes to a next higher level up to EasyStart Timer OFF the Start display appears and no function is active EasyStart Timer OFF EasyStart Timer is in submenu gt the setting is exited already set values are not saved if the display shows OFF gt EasyStart Timer ON the Start display appears Press Sj button 1x keep pressed EasyStart Timer is in the Main menu and the Start display appears in the Menu bar the next right hand symbol appears in the middle and flashing EasyStart Timer is in the gt submenu the dis played value is changed larger or the next selec tion is displayed if the display shows OFF gt EasyStart Timer ON the Start display appears Press E button 1x keep pressed EasyStart Timer is in the Main menu and the Start display appears in the Menu bar the next left hand symbol appears in the middle and flashing EasyStart Timer is in the gt submenu the dis played value is changed smaller or the next selection is displayed if the display shows OFF EasyStart Timer ON the Start display appears 6 VEHICLE HEATERS TECHNICAL DOCUMENTATION 3 OPERATION AND SETTING ADJUSTMENT NOTES ON OPERATION AND SETTING ACTIVATING THE EASYSTART TIMER If the display is not lit the EasyStart Timer must be activated not if heating ON with LONGPRESS SHORTPRESS on one of the four buttons the Start display appe
26. ton to select the weekday group Mon Fri Sat Sun Mon Sun or a weekday Mon Tue Wed Thu Fri Sat Sun slo P SQ Press the button to confirm the setting SETTING THE DEPARTURE TIME START TIME Use the Ell or ES button to set the hours sl ZS Press the button to confirm the setting Use the I or El button to set the minutes slo Z Press the button to confirm the setting 24 VEHICLE HEATERS TECHNICAL DOCUMENTATION 3 OPERATION AND SETTING ADJUSTMENT SELECTING THE OPERATING MODE Use the Ez or Ex button to deselect the sym bol or the 8 symbol l2 ZI Ne A S Confirm the HEATING or VENTILATION function by pressing the button SET TEMPERATURE SETPOINT FOR AIR HEATERS ONLY Use the El or EJ button to set the temperature setpoint Temperature setpoint setting range 8 C 36 C in 1 C increments 46 F 97 F in 1 F increments Ne ds Press the button to confirm the temperature setpoint SELECTING THE HEATING LEVEL only for water heaters with automatic operating time calculation ECO heating level normal heating approx 20 C HIGH heating level convenient comfortable heat ing approx 23 C Select ECO heating level or HIGH heating level using the EE or ES button sl Ir Press the button to confirm the heating level SETTING THE OPERATING TIME Use the I or ES button to set the operating time Op
27. u item SHORTPRESS button the Start display appears if the SHORTPRESS button is pressed again Display OFF SHORTPRESS button the VENTILATION submenu is displayed VENTILATION OFF WITH SHORTPRESS Display ON the VENTILATION menu item is displayed Press the SHORTPRESS button for less than 2 seconds Heater OFF wl A fis After the VENTILATION OFF display the Start display appears If the vehicle lighting is OFF the display lighting goes out after 10 seconds wl Zi Bi PLEASE NOTE The heater switches off an active add on unit remains in operation The following actions are possible during the VENTILATION OFF display Use the IE or uml button to select a menu item SHORTPRESS button the Start display appears if the E SHORTPRESS button is pressed again Display OFF SHORTPRESS button the VENTILATION submenu is displayed 16 VEHICLE HEATERS TECHNICAL DOCUMENTATION 3 OPERATION AND SETTING ADJUSTMENT ADD ON UNIT ON E G ACTIVATE THE HEATING FUNCTION FOR A 2ND HEATER Display ON the Start display appears Use the Ez or Ex button to select the Ap symbol in the Menu bar wl Confirm the ADD ON UNIT menu item by pressing the button Use the Ez or Ex button to select the 333 symbol wv l2 2 gt Confirm the HEATING function using the button I PLEASE NOTE The following settings or confirmations are absolutely necessary SET TEMPERATURE SETPOINT
Download Pdf Manuals
Related Search