INSTALLATION MANUAL
Contents
1. STRAIGHT ARM COVER erm ww www www nw nee LEFT HAND gv ARTICULATED ARM Pa Ss wee w www www nw nnnn RIGHT HAND APROLI 280 700 STRONG SETTING APROLI 280 700 STRONG In order to install the device it is firstly necessary to dismantle and expose the individual components fundamental for both optimal installation and good performance Swing the lock cover flap placed on the left side of the front protection cover to one side for both the RH and LH Aproli and open the cover with the customized key provided Pic 4 A Remove the bended arm by unscrewing the fixing screws positioned on the rotation shaft for both the RH and LH Aproli Pic 4 B Remove the protection cover by unscrewing the two fixing screws A on the cover Pic 4 C PROTECTION TOPE RAUN LOCK COVER HINGED JACK ASSEMBLY STOMIZED KEY CUSTO PROTECTION COVER PILLAR FIXING BASE AND BRACKET PROTECTION COVER FIXING SCREWS FOR ATTACHING THE BENDED COVER FIXING RIGHT HAND pes ARM TO THE ROTATION SCREWS A 3 SHAFT BENDED ARM PIC 4 A PIC 4 B PIC 4 C lt In order to extract the electric motor hydraulic jack assembly from the fixing base unscrew the four fixing screws B positioned under the fixing base Pic 5 BENDED ARM AND TELESCOPIC CONNECTION ARM The straight arm should be bolted to the bended arm The straight arm offers vari2. ROLI 280 700 sron gt OIL HYDRAULIC OPERATOR DESIGNED FOR SWING GATES WITH VERY LARGE PILLARS AND HEAVY GATES INSTALLATION MANUAL gt il i FADING the gate opener APROLI 280 700 stone INSTRUCTIONS FOR THE INSTALLATION OF THE APROLI 280 700 STRONG SWING GATE OPERATOR FOR CORRECT APROLI 280 700 STRONG INSTALLATION AND GOOD PERFORMANCE PLEASE READ THE INSTRUCTIONS OUTLINED IN THIS MANUAL CAREFULLY AND KEEP TO THE DIAGRAMS IMPORTANT THE ENTIRE INSTALLATION MUST BE CARRIED OUT BY QUALIFIED TECHNICAL PERSONNEL WHO ARE ADVISED TO FOLLOW GOOD INSTALLATION PRACTICE AND KEEP TO CURRENT SAFETY STANDARDS GENERAL INFORMATION Check that the structure of the gate to be automated is suitable for the application to be installed make sure that there are no anomalies in the metal structure reinforce any weak points and ensure that the leaf hinges are in perfect condition If necessary reinforce the connection point between the leaf and the bended arm fixing shoe The gate s movement should not be obstructed in any way excessive rises in the ground friction in the hinges The gate leaves must be installed and levelled on a flat surface The Aproli 280 700 Strong is an external oil hydraulic gate operator for swing gates with two directional hydraulic locking suitable for gates with very large pillars and for heavy gates It meets all the most demanding installation requirements thanks to the use
3. Should more pairs of photocells be required than the recommended quantity fit an auxiliary transformer outside the control box 1 radio receiver Max permitted load L N W for special applications ie to switch on lights CCTV etc SOLID STATE RELAYS are recommended to be used only Standard relays would affect the micro processor N W THIS PANEL IS TESTED TO OPERATE GATES ONLY THROUGH FADINI PULSE TWICE ALL OPERATIONS ACCESSORIES NO GUARANTEE FOR ACCESSORIES OF OTHER MAKE OR CONSECUTIVELY TO OPEN OPEN CLOSE amp REVERSE SPECIAL APPLICATIONS BOTH GATE LEAFS RADIO CONTACT Drwg No 2014 FEATURES OF THE ELECTRONIC PROGRAMMER ELPRO 13 CEI FOR SWINGING GATES All the electrical connections are to be made as per the following instructions and diagrams Supply the terminals 24 25 with 230V 50 Hz single phase voltage The red LED switches on and stays on as long as the board is properly supplied Through the timer No 9 you can control the running time of the motor in both cycles OPEN and CLOSE Set it so that the running time of the motor is longer than the actual travel of the gate set the timer No 8 DWELL ie the interval between open and re closing so that you can meet the required interval of time The timer No 7 LEAF DELAY in close cycle is to be set as follows on to less the delay is out of service clockwise on to more the delay is operative With the electric mot
4. O ae LES EXPLODED VIEW OF MAIN COMPONENTS OF LEFT HAND APROLI 280 700 STRONG GATE OPERATOR PILLAR FIXING BASE AND BRACKET FIXING SCREWS B FOR ELECTRIC MOTOR HYDRAULIC JACK ASSEMBLY FIXING SCREWS FOR ATTACHING BENDED ARM TO ROTATION SHAFT gt PIC 2 APPLICATION OF TWO APROLI 280 700 STRONG Before proceeding with the installation and use of the Aproli 280 700 Strong itis essential to understand the exact position of each operator in the system The automations have the abbreviation Sx left and Dx right stamped on the hydraulic jack which can be seen once the protection cover has been removed in fact Right and Left are intended for an observer standing in front of the two gate leaves to be opened towards the observer himself Pic 3 l e if the gate opens inwards the observer will be standing inside and will see the right hand Aproli 280 700 Strong on his right vice versa if the gate opens outwards the observer will be standing outside and will see the right hand Aproli 280 700 Strong on his right LEFT HAND ELECTRIC MOTOR HYDRAULIC JACK ASSEMBLY PROTECTION COVER LEAF FIXING SHOE COVER FIXING SCREWS A ADJUSTABLE TELESCOPIC STRAIGHT ARM ROBUST LEFT HAND BENDED ARM LEFT HAND APROLI 280 700 STRONG OBSERVER STANDING IN FRONT AGAINST THE LEAF OPENING DIRECTION
5. of cycles a year 8 hours a AaY eecececeeeeseeesteeteseeees 137 000 OVERALL DIMENSIONS gt Pree yy J VAI O DES 140 CHECKING AND MAINTENANCE To achieve an optimum performance and longer life of the equipment and in observance of the safety regulations itis recommended that inspetions and proper maintenance are made by qualified technicians to the whole installation ie both the mechanical and electronic parts as well as wiring Mechanical parts maintenance every 6 months approx Electronic apparatus and safety equipment maintenance every month The CE mark certifies that the operator conforms to the essential requirements of the European Directive art 10 EEC 73 23 in relation to the manufacturer s declaration for the supplied items in compliance with the body of the regulations ISO 9000 UNI EN 29000 Automation in conformity to EN 12453 EN 12445 safety standards THE ESSENTIAL REQUIREMENTS OF THE EUROPEAN MARK CERTIFYING CONFORMITY TO STANDARDS 98 37 EC DECLARATION OF CONFORMITY GENERAL WARNINGS EN 12453 EN 12445 STANDARDS CEI EN 60204 1 STANDARDS WARRANTY CERTIFICATE ON THE CUSTOMER S REQUEST meccanica FADING AUTOMATIC GATE MANUFACTURERS The growth of MECCANICA FADINI has always been based on the development of guaranteed products thanks to our TOTAL QUALITY CONTROL system which ensures constant quality standards updat
6. initial manoeuvre operations it will be necessary to calibrate the opening and closing drive force that each individual Aproli 280 700 Strong exercises on the leaves it is therefore necessary to remove the protection cover Pic 12 firstly using the customized key on the cover thereby exposing the automation and the individual pressure regulators that can be adjusted using a flat screwdriver NOTE during factory production the two hydraulic pressure regulators on each individual Aproli 280 700 Strong are distinguished by different colours on the Right Aproli and the Left Aproli the red regulator adjusts the drive force of the leaf during closing while the green regulator adjusts the drive force of the leaf during opening Pic 12 LEFT HAND APROLI 280 700 STRONG RIGHT HAND APROLI 280 700 STRONG DRIVE FORCE DRIVE FORCE ADJUSTMENT ADJUSTMENT VALVES VALVES PROTECTION COVER COVER FIXING SCREWS A LEFT HAND APROLI 280 700 STRONG RIGHT HAND APROLI 280 700 STRONG RED REGULATOR DRIVE l GREEN REGULATOR DURING CLOSING GREEN REGULATOR DRIVE DURING OPENING RED REGULATOR DRIVE DURING CLOSING DRIVE DURING OPENING i i CLOCKWISE ooi ou MORE DRIVE hoa i FORCE i i i ANTICLOCKWISE P oi MANUAL RELEASE LESS DRIVE FORCE MANUAL RELEASE LEVER oo i LEVER S Sata ict tad Dt A aa tes Gt EAE ee gt PIC 12 TECHNICAL
7. DATA ELECTRIC MOTOR OIL HYDRAULIC PUMP Power OUtDUL cccesseessessecseessesstsseeseeseesneeseeseeseeeees 0 18 KW 0 25 HP Pump flow rate P3 cesessesssessesseesesseestesessessessesseeseeess 0 85 min Supply voltage Frequency cecsesesesseesesseeees 230 V c a 50 Hz Average working pressure 1 MPa 10 bars Absorbed turrente aAa 250 W Max PUMP pressure ceseeseecessesseeseseeeseeseeseeseesees 3 MPa 30 bars Absorbed POWED s ss csecsesesseseesecsesseeseeeeseeeeesesneeseseeseeaeeaseeeess 1 2A Working temperature se ccccccseceesessesseeseseeseeseeseeeees 20 C 80 C Capacities cicatadielasritaleaddsarinasienaeeiriebsabisileriesieiteciiacteite 12 uF Hydraulic Oil eeeecseceeseesesseeeeeeesesseeseeees OIL A 15 FADINI by AGIP Motor rotation speed ecccsecseceeeesesteeeesteeeteeeeeteeteeees 1 350 rpm Static weight of operator with arm cessesseectesseestesteeteesees 20 Kg Intermittent SCPViCE cecseceeseeceseseeseeseseeeseeseeeeeseseeeteseenteeeeaeeeeaees 3 OPO mim UME daesh Aaah becstectetiaa etanaecel esata tadcatitanttian bend 23 s Rated torque eccsssecsecsessesessessececsessessesseeseseseeseeacsessteseeasseeess 137 Nm SERVICE Duty cycle 23 s Opening 30 s Dwell 23 s Closing Time of one Complete cycle eccceeceseeteeseeeeteeteseeteeeeeeeseeeees 76s No of complete cycles Open Dwell Close 47 cycles hour No
8. EN CYCLE N 3 OFF NO AUTOMATIC RECLOSING N 3 ON AUTOMATIC RECLOSING N 4 OFF NO PRE FLASHING N 4 ON PRE FLASHING N 5 OFF REMOTE CONTROL NO STOP AND HOLD AS LONG N 5 ON STOP AND HOLD AS LONG AS AS BUTTON DOWN IT OPENS STRAIGHT AWAY THE BUTTON IS KEPT DOWN N 6 OFF BOTH LEAFS ARE OPERATED N 6 ON PEDESTRIAN ONE LEAF ONLY GATES IN CLOSE POSITION N 7 OFF S R P OUT OF SERVICE N 7 ON S R P IN SERVICE GATES IN CLOSE POSITION N 8 OFF LEAF DELAY OPEN CYCLE N 8 ON NO LEAF DELAY ONE STARTS BEFORE THE OTHER BOTH MOTORS START TOGETHER LAMP ON GATE OPEN LAMP FLASHES SLOWLY GATE OPENING LAMP FLASHES FAST GATE CLOSING LAMP OFF GATE CLOSED 1 Itis advisable not to expose the control box directly to weather conditions if mounted outside a suitable enclosure is recommended to protect it from sunshine and rain 2 Bridge terminals 1 2 if you do not require any photocells 3 Should two sets of photocells be required these are to be series connected to terminals 1 2 contact normally closed 4 Bridge terminals 6 8 if you do not require any keyswitch or push buttons 5 Fit the mains to the control box with a high sensitivity differential magnetic thermal switch 0 03 Amps 6 OPERATING MODE WITH TWO PAIRS OF PHOTOCELLS INDEPENDENT FROM EACH OTHER Dip switch No 1 set to OFF connect the pair of photocells that are inside the property to the terminals marked 2 4 pair The second pair always s
9. ND APROLI ELECTRIC 14 PHOTOCELL RECEIVER POLO 44 LEFT ener gt PIC 9 Once all the electrical connections have been made carry out the initial operation tests adjust the motor run timer 09 for a period of 4 5 seconds more than the real gate opening time the dwell timer 08 and the leaf closure delay 07 Pic 10 In order to set automatic or semiautomatic operation flick the Dip switch B Automatic Operation with dip switch lever No 3 in the ON position once the opening pulse has been given contact 4 and 8 on the Elpro 13 CEI programmer terminal box the gate opens and dwells for the time set by the potentiometer 08 then closes automatically Semiautomatic Operation with dip switch lever No 3 in the OFF position once the opening pulse has been given the gate opens while a closing pulse must be given in order to close in contact 5 and 8 on the Elpro 13 CEI programmer terminal box Radio Contact contact 7 and 8 on the Elpro 13 CEI electronic programmer terminal box Pic 10 the automation reverses the movement that it is carrying out upon every pulse from the keyswitch the transmitter or the wall push buttons it is advisable to read the instructions leaflet enclosed with the electronic programmer carefully WARNING If the electric motors have insufficient drive power due to shortage of electric current add two 12 uF capacitors one for each electric motor connecting them
10. allation and connection phase Power supply electric motor and flashing light connections are made with electric cables with a section of 1 5 mm for a maximum distance of 50 m For distances of over 50 metres we recommend using electric cables with a section of 2 mm For limit switches photocells pushbuttons and accessories use cables with 1 mm wires Pic 9 IMPORTANT PERFORM A RISK ANALYSIS IN COMPLIANCE WITH EN 12445 AND EN 12453 STANDARDS AND INSTALL THE NECESSARY SAFETY DEVICES THE FOLLOWING FIGURE PROVIDES AN INDICATION OF THE ESSENTIAL ACCESSORIES FOR THE SYSTEM OPERATION THE SYSTEM SHOULD BE CUSTOMIZED AT THE INSTALLER AND USER S DISCRETION DEPENDING ON THE VARIOUS REQUIREMENTS AND CHARACTERISTICS OF THE ENVIRONMENT 11 1 ELPRO 13 CEI PROGRAMMER WITH PLUG IN JUBI 433 RADIO RECEIVER 2 0 03 A MAGNETO THERMAL DIFFERENTIAL SWITCH 3 JUNCTION BOX 4 LEFT HAND APROLI 280 700 STRONG 5 PHOTOCELL TRANSMITTER POLO 44 ON POST 6 GATE STOP IN OPEN GATE POSITION 7 JUBI SMALL 433 TRANSMITTER 8 ELECTRIC LOCK 9 PHOTOCELL RECEIVER POLO 44 ON POST 10 RIGHT HAND APROLI 280 700 STRONG 11 ENCODED KEYSWITCH PRIT 19 12 MIRI 4 FLASHING LIGHT FITTED WITH BIRIO ANTENNA 13 PHOTOCELL TRANSMITTER POLO 44 LEFT HA
11. ed knowledge of the European Standards and compliance with their requirements in view of an ever increasing process of improvement FADING the gate opener Made in Italy Distributor s box The manufacturers reserve the right to change the products without any previous notice Via Mantova 177 A 37053 Cerea Verona Italy Tel 0442 330422 r a Fax 0442 331054 e mail info fadini net www fadini net
12. en immediately reverses into OPEN This will help the gate lock to release All the other operations will be performed in the standard way No danger comes from the Stroke Reversing Pulse This function remains in service with the panel set to Pedestrian Mode Set Dip switch No 6 to ON for Pedestrian Mode S 1A P terminals 3 4 Only one leaf is operated when the OPEN button is pressed down Automatic reclosing If the OPEN button is pressed twice in a row both leafs are opened The S 1A P function is activated only when the gate is in the fully CLOSE position The remote control always operates both gates terminals 7 8 The box of ELPRO 13 CEI and its cover are made of weather proof shock resistant plastic material which has a degree of protection equalling IP 437 The cover is fitted with a knob of quick response in case of an emergency by cutting off the voltage supply MANUAL RELEASE The Aproli 280 700 Strong manual release makes it possible to move the gate manually in the case of a power failure or during the initial manual opening and closing tests The manual release lever S can be accessed by opening the protection cover with the customized key Lower the lever in order to release the gate Pic 11 PROTECTION COVER MANUAL RELEASE LEVER S INSIDE LOWER THE MANUAL RELEASE LEVER S TO RELEASE MANUAL RELEASE LEVER S PIC 11 ADJUSTING THE LEAF DRIVE FORCE During the
13. in parallel to the individual electric motor phases Elpro 3 cei FOR SWING GATES SINGLE PHASE RADIO CONTROL PLUG IN CARD SUPPORT ANT Ooo THE DELAY IS OUT OF SERVICE LEAF DELAY CLOSE TIMER 0 1 Amp FUSE 24 V OUTPUT DWELL TIME TERMINALS 12 13 IF 26 A 27 HQ errs 28 HAO CY t TANNVHO ol LNdLNO At TERMINALS FOR THE Pp O FADINI O CONNECTION OF THE a PUSH BUTTONS PULIN 3 7 MICROPROCESSOR 8 9 MOTOR RUN CUT OFF SWITCH IME CREN BY COVER KNOB CAPACITORS E DIP SWITCH EL ON ON Os WAUUUUUEI AY 12345678 OFE 630 mA FUSE FLASHING LAMP m ELECTRIC LOCK SUPPLY o 230 V SINGLE PHASE ELECTRIC MOTORS SUPPLY VOLTAGE SINGLE PHASE N C CONTACT PHOTOCELLS COMMON COMMON VOLTAGE OUTPUT 24 Vac OUTPUT 230 V 25 W max FLASHING LAMP RADIO CONTACT N 0 2 pairs photocells 24 V 3 W max INDICATOR gt PHOTOCELLS 2na PAIR INSIDE PHOTOCELLS N C contact If obstructed they prevent the gates fro opening reverse gate direction during close cycle OPEN SWITCH N O CONTACT CLOSE SWITCH N O CONTACT STOP SWITCH N C CONTACT LED 1 LIGHTS UP WHEN THE CARD IS POWERED LED 2 SWITCHES OFE WHEN THERE IS AN OBSTACLE IN FRONT F THE PHOTOCELLS PEDESTRIAN MODE LED 3 OPEN LIGHTS UP UPON OPENING PULSE ONE GATE LEAF ONLY LED 4 CLOSE LIGHTS UP UPON CLOSE PULSE LED 5 STOP SWITCHES OFF UPON STOP PULSE LED 6 RADIO LIGHTS UP UPON EVERY RADIO PULSE
14. indicated installation heights Pic 8 gn Once the fixing base has been installed insert and fix the electric I AA 4 motor hydraulic jack assembly into position using the 4 fixing screws cies aw L S U B Pic 5 E lt lt QU The following table indicates some installation distances These are not obligatory and are for reference purposes only Pic 8 s X POWER CABLE ALREADY The distances indicated must be used to obtain an automation that A y INSERTED INSIDE TUBE is able to close the leaf decisively g INSTALLATION INSIDE THE PILLAR S FIXING BASE AND BRACKET PIC 7 lt Pillar dimensions A mm B mm C mm D mm G Gate leaf 400 x 400 mm 510 200 460 50 100 2 0 m 500 x 500 mm 560 250 460 60 100 3 0 m 600 x 600 mm 560 300 460 95 1 80 m 700 x 700 mm 580 350 580 140 95 3 0 m 800 x 800 mm 620 400 580 135 90 40m 900 x 900 mm 650 450 580 50 90 5 0 m GATE STOP IN 40 CLOSED GATE 20 mm from the pillar edge A POSITION Y PILLAR CLOSED LEAF OPEN GATE POSITION y PIC 8 ELECTRICAL CONNECTIONS TO THE ELPRO 13 CEI PROGRAMMER Before making any connections study the enclosed electrical diagrams carefully IMPORTANT The whole electrical system must be earthed Pic 9 DO NOT CUT the electric cable for installation requirements CUT OFF the 230 V power supply line switch not connected Pic 9 during the electric wiring inst
15. of a bended steel arm and telescopic end section for leaf fixing We recommend using the Aproli 280 700 Strong for leaves of no more than 3 0 metres long and weighing more than 300 kg IMPORTANT The Aproli 280 700 Strong should only be installed on gates with leaves up to 3 0 metres long An electric lock must always be installed for leaves of over 2 0 metres long Itis advisable to fasten all the open and closed gate stops firmly to the ground and to check how sturdy they are during the initial gate operation tests Pic 1 GATE STOP IN CLOSED GATE POSITION CLOSED LEAF CLOSED LEAF PILLAR PILLAR LEAF FIXING SHOE 1 ue LEFT BENDED ARM RIGHT BENDED ARM ue i 4 i SeSi send l L2 2 sossS5 1 Ww U sy i S 1 O oO LEFT HAND ie i RIGHT HAND APROLI 280 700 G ri N APROLI 280 700 STRONG oi GATE STOP IN OPEN o STRON GATE POSITION sad PLAN OF GATE WITH TWO APROLI 280 700 STRONG INSTALLED PIC 1 Firstly slide off the whole bended arm by unscrewing the specific screw on the rotation shaft then remove the protection cover by unscrewing the 2 fixing screws A Pic 2 one of which is found inside by opening the cover with the customized key At this point unscrew the 4 locking screws B positioned beneath the automation Pic 2 thereby making it possible to remove the electric motor hydraulic jack assembly exposing the pillar fixing bracket 5
16. one leaf only can be operated allowing people to walk in out STOP and HOLD function by keeping the remote control button pressed down Further improvements can be noted in the Elpro 13 CEI Addition of a 1 Amp fuse to the 24 V circuit as a protection for the accessories remote control photocells etc which are connected to the terminals 12 13 and for the panel itself in that it can prevent short circuit during installation The pulse to the electric lock is increased to 2 seconds Releasing is so much easier as the electric lock is released with an anticipation of 100 msec before the gate starts moving A 24V 3 W lamp indicates gate operations Gate CLOSED Lamp OFF Gate in OPEN cycle Lamp flashes slowly Gate OPEN Lamp stays ON without flashing Gate in CLOSE cycle Lamp flashes fast It provides a better switching intelligence design to enhance the reliability of the relays The Motor Run Time is independent from the Leaf Delay Time in close cycle the delay time is automatically added to the duration of the opening time The 8 Dip switches can be arranged into any of the possible patterns to achieve the required operating modes without any risk of interference with one another STROKE REVERSING PULSE and S 1A P Set Dip switch No 7 to ON The Stroke Reversing Pulse S R P is activated only with the gate in the CLOSE position The pulse operates the gate in the CLOSE direction first and th
17. or connected to terminals 19 20 21 the delay is operative in the open cycle with a factory pre set time With the electric motor connected to terminals 16 17 18 the delay is operative in close cycle and can be adjusted through the timer No 7 on to less or more LOGIC OF THE ELECTRONIC PROGRAMMER When a pulse is given the flashing light switches on After three seconds the motors start During the interval before re closing the light stays on When the gates are fully re closed the light keeps on flashing for three more seconds and then switches off automatically The 3 second interval pre flashing which precedes the actual start of the motors can be eliminated by means of the DIP SWITCH B No 4 LED No 1 It switches on when voltage is supplied LED No 2 PHOTOCELLS Normally on It switches off when the photocells are obstructed LED No 3 OPEN It switches on when the respective switch is activated LED No 4 CLOSE It switches on when the respective switch is activated LED No 5 STOP Normally on It switches off when the respective switch is activated LED No 6 RADIO It switches on whenever a pulse is given either from remote control keyswitch or push buttons DIP SWITCH B SETTING IN ELPRO 13 CEI N 1 OFF PHOTOCELLS NO STOP IN OPEN CYCLE REVERSE CLOSE N 1 ON STOP DURING OPEN CYCLE N 2 OFF REMOTE CONTROL REVERSE N 2 ON NO REVERSE DURING OP
18. ous different assembly solutions since it has holes for connection with the telescopic arm cover in 3 different positions Pic 6 obtaining a centre distance between the bended arm and the fixing shoe equivalent to 460 mm 520 mm or 580 mm The fixing shoe is attached to a robust gate upright with screws or firmly welded in place and is then connected to the adjustable straight arm with one screw ELECTRIC MOTOR STRAIGHT LEAF FIXIN HYDRAULIC JACK a ARM COVER Be G ASSEMBLY LEFT HAND BENDED ARM ADJUSTABLE TELESCOPIC STRAIGHT ARM PILLAR FIXING BASE AND BRACKET CENTRE DISTANCE l l FIXING SCREWS B 460 mm 520 mm 580 mm e4 ELECTRIC MOTOR n l ba ee HYDRAULIC JACK ASSEMBLY gt PIC 5 PIC 6 lt FIXTURE TO THE PILLAR ee ee Using a spirit level fix the fixing base in position with suitable fixing poy plugs depending on the type of pillar Pic 7 not provided When ay SEO deciding the height at which to fix it to the pillar consider at what ae a point the articulated arm will be connected to the gate leaf preferably on a strong upright The fixing shoe Pic 6 must be bolted or welded into position at a distance established after the initial manual leaf DNS opening and closing tests following the
19. tops the gate in open cycle in case of an obstacle During close cycle the second pair reverses the gate direction 7 NOTE WELL FAULT FINDING Check supply voltage with a tester it must be 230 V single phase Check the high voltage fuses Check the low voltage fuses Check if the photocell contacts are normally closed Check voltage from the control box to the electric motor s power might have dropped The section of the electric cables to the motor s must not be less than 1 5 mm Connect the other pair to the terminals 1 2 This pair performs in the standard pre set mode ie no stop during open cycle REVERSING GATE DIRECTION DURING CLOSE CYCLE Terminals to stay linked out should the second pair of photocells not be used and set the desired operating mode through Dip switch No 1 24 V output Terminals 12 13 It can supply power for 2 pairs of photocells plus 1 radio receiver Terminal 11 provides a power output for a lamp 24 V 3 W max Flashing lamp output Terminals 22 23 Maximun available power 25 W max FEATURES AND TECHNICAL SPECIFICATIONS Elpro 13 CEI represents the latest state of the art technology for control panels It is extremely versatile and can meet the most various requirements It is fitted with the Cut Off Switch by cover knob It has the same functions as Elpro 9 and incorporates additional advantages as follows Stroke Reversing Pulse Pedestrian Operating Mode where
Download Pdf Manuals
Related Search