Home

GSM Remote Security Camera User Manual

1. Successful SMS reply The password has been successfully changed to iW50 User Manual Version 1 2 15 www orbien co uk Failed SMS reply If a user other than the master user attempts to change the password a notification message will be sent via SMS Sorry you are not authorized to use this command 3 3 Define family user Family users have the authority to listen in on the camera receive images load the sensors and remote controls to the camera and receive notification when motion detection activated The family user s mobile numbers are set by the Master user The family users should save iW50 SIM card number into their mobile phones with the suggested name iW50 Camera 3 3 1 Add a family number Authority Master user Method The user sends following SMS message in order to Add a family number O6 FamilyNumber Add several family numbers 06 FamilyNumber FamilyNumber e Up to 10 family users number can be stored on one camera Successful SMS reply The family number has been added successfully 3 3 2 Check family user s number Refer to Chapter 4 15 Check status 3 3 3 Delete family number Authority Master user Method The user sends following SMS message in order to Delete a family number 113 FamilyNumber Delete several family numbers 113 FamilyNumber 4 FamilyNumber Delete all family numbers 113 iW50 User Manual Version 1 2 16 www orbien co uk Successful
2. iW50 User Manual Version 1 2 8 www orbien co uk 1 4 Remote control instruction 1 Antenna 3 Arm the camera button 2 Remote control indicator 4 Disarm the camera button 5 Emergency button Battery Note The battery holder is at the rear of the remote control When the remote control senses low battery the iW50 will emit a beep beep warning tone and then send a SMS notification to your mobile phone 1 5 iW50 LED Light indicator Color Status Flash slowly Searching the network Sensor alarm motion detection alarm infrared body Flash quickly detector alarm Constant Light Not installed SIM card or the remote camera damaged Constant Light Armed status Flash slowly Disarmed status Green Flash quickly Processing data Light 2 seconds Successfully reset factory setting or loading sensor Orange Flash Loading remote control status Red and Two color lights Loading sensor Green alternately Note a slow flash means 1 flash second and a quick flash means 2 flashes per second iW50 User Manual Version 1 2 9 www orbien co uk Chapter 2 Getting started 2 1 Install the SIM card e Remove the rubber cover from the left side of the camera e Open the SIM card slot by pressing the small dot beside the SIM card slot with the tip of a pencil and pop open the slot e Insert the SIM card into the slot e Push the slot back into place e Put the rubber cover back in its place Note
3. W550 GSM Remote Security Camera User Manual Introducing the iW50 GSM Remote Security Camera Thank you for purchasing the iW90 GSM Security Camera This camera is a remote controlled portable security camera designed for use with your mobile phone The camera consists of a high quality 300 000 pixel camera lens microphone and infrared lights The iW50 camera will capture colour pictures according to a pre programmed remote command and then send those pictures to multimedia messaging MMS enabled mobile phones and or Email addresses With the built in infrared LED s the iW90 is able to capture clear images even when dark No matter where you are in the world using your mobile you can send simple SMS messages to control and change the camera settings Once the iW90 is placed in the ARM state the motion detector or infrared body detector will trigger if either senses a change On triggering the iW90 will notify you or family and friends by sending you an SMS message followed shortly by an MMS The camera can also be configure to send notifications and picture to preset Email addresses The iW90 is a GSM based device and must be supported by a Mobile Network Provider and SIM card with the Sim card MMS function and Caller ID Presentation function activated and PIN code deactivated The receiving mobile phones must be enabled to receive MMS messaging in order to receive pictures from the camera iW50 User Manual Version 1 2 2 www
4. 320 240 QVGA 4 11 3 Disarming the camera manually Authority Master and family users Description When the camera is working under disarmed mode all loaded wireless sensors integrated infrared body detector and motion detection function will trigger But it will send an SMS MMS notification or make phone calls only when button on remote control is pressed Method Method 1 The user sends following SMS message in order to Disarming the camera manually 02 Method 2 e Press the P button on the remote control whilst pointing it in the direction of the camera Method 3 The user calls the camera and hangs up within 5 20 seconds upon hearing the ring tone in the phone The camera will be armed or disarmed Successful SMS reply Defense mode de activated iW50 User Manual Version 1 2 33 www orbien co uk The camera will emit a Beep tone and the indicator light will flash green 4 12 Timed arming the camera Authority Master and family users 4 12 1 Enable timing arms the camera Method The user sends following SMS message in order to Enable timing arms the camera 128 1 Successful SMS reply Timing defense activated Then the camera will arm automatically according to the settings 4 12 2 Set time period to arm the camera Method The user sends following SMS message in order to Set time period to arm the camera 129 WorkDay ArmTime1 DisarmTimet 4ArmTime3 Disarm Time3
5. e f greater than 9 emergency numbers the maximum amount per camera are used on iW50 camera and the master user attempts to add another one the following notification message will be sent via SMS The Emergency numbers are full Please delete old numbers e If an existing number is being added again the following notification message will be sent via SMS Emergency number already exist 3 5 2 Delete emergency number Authority Master user Method The user sends following SMS message in order to Delete an emergency number 107 EmergencyNumber Delete several emergency numbers 107 EmergencyNumber EmergencyNumber Delete all emergency numbers 107 Successful SMS reply Emergency number successfully deleted 3 5 3 Check emergency number Refer to Chapter 4 15 Check status Chapter 4 Basic use and settings 4 1 Network parameter settings Authority Master user Description In general network parameter settings do not need to be set up before use if using a Contract based Sim Card as the iW50 will automatically apply the Network parameters if the following SMS command is sent 54 However if the camera is unable to send MMS messages it may mean that the network parameters have iW50 User Manual Version 1 2 18 not been detected or the Sim being used is a PAYG pre paid Sim and parameter settings will need to be applied manually After successfully setting the network parameters
6. 2 47 www orbien co uk
7. 3 with the default image size 320x240 and the Image capturing interval time 0 5s e The quantity value should be in the range of 2 8 e If the image size is 640x480 up to 2 image quantity can be used iW50 User Manual Version 1 2 38 www orbien co uk e The image size and image capturing interval time can be changed see chapter 5 1 1 and 5 1 3 Successful SMS reply Alarm image quantity has been set successfully 5 1 3 Image interval For master and family users 103 time e The Interval time values should be in the range from 3 10 e Each unit constitutes 100ms e The default value is 5 i e 0 5 seconds Successful SMS reply Capture image interval time has been set successfully 5 2 Automatic alarm settings Description The camera will enter auto alarm mode and send notification messages SMS and or MMS to the previously set numbers or Email addresses in one of the following two circumstances e When motion is detected or e When the wireless sensors are triggered The user sends the following edit message via SMS to the camera in order to activate the following functions 5 2 1 Warning tone upon alarm triggering e For master and family users 130 1 Successful SMS reply Warn sound mode activated The camera will emit a Beep tone upon alarm activation 5 2 2 No warning tone upon alarm Default For master and family users 130 0 iW50 User Manual Version 1 2 39 www orbien co
8. 4 7 3 Listening in upon automatically alarm ee eceeceeeseseeseseeecseseecesceeceeseeeseaeseeeceeseeeseeeeeeees 27 48 Infrared body detecto tissieri e ae REA ER E preemies ret 28 AD Motion detection s scctccccvscaceccscecesssdeedavecuscsdoccvesceecvascisecsdunconcsssdsaseledcucvecesveveendedceovis sstceernenecessioontees 28 4 9 1 Activate Deactivate motion detection oo ceeseesseteeseseeecseeeesesceecseeneeeeeeseeeceeeeseeeeeeeeees 29 4 9 2 Send five Images UPON Motion detection AAPM ceccsecceteeseeeeceeeeeseteesescecseeeeeeseeeeeees 29 4 10 Wireless SEMSOL S 5 s05 08 X4cee c0 e cbse Fades ev hid ca veabes aE E EE tb eiwidoe Rov ES 30 4 10 1 Add a wireless sensor and set corresponding alarm MOdEC ccccccecseeeesetetteteeseeeees 30 4 10 2 Remove wireless SENSOM csccsssssssscessscessesscessecessesasessecessesacassecassecevsesaasnecessenavasee saves 32 4 11 Arming or disarming the camera manually 0 ccesscsssesseeceeceecsecseseseeeseesceaeneeaeseteaeeaceaeaeeateeees 32 4 11 1 Arming the Camera manually 00 ceceeceecceecseseeseseeecsescecesceeceeseecescnecetsecesaeeaesceecaeaenaeaceeeaees 32 4 11 2 Default arming MOE cece csssssssssecseesesseseeseesensessescsecsecusssecseseesesaesaecseseesesseeseaeseeseeaees 33 4 11 3 Disarming the Camera MANUAll yn cececeecsssceseseeecseeeseseeeceeseeaesceeceeeeceeaesceaeeeceeseeaeaeeeeeeaes 33 4 12 Timed arming the Cameraissivc cciacedavescssveacesavseteiaeusepareiavencviauss
9. EmailAddress Successful SMS reply Email address 4 3 2 Delete all E mail address es Authority Master user iW50 User Manual Version 1 2 22 www orbien co uk Method The user sends following SMS message in order to Delete all E mail address 109 Successful SMS reply E mail addresses deleted successfully 4 4 Timing send images to mobile Authority Master user 4 4 1 Enable timing sends MMS images Method The user sends following SMS message in order to Enable timing sends MMS images 115 1 Successful SMS reply Set timing to send MMS activated 4 4 2 Set time period to send MMS images Method The user sends following SMS message in order to Set time period to auto send MMS image 116 WorkDay StartTime1 EndTime1 intervelTime1 StartTime3 EndTim e3 intervelTime3 Note Maximum allowed is 3 periods per workday Each period time should set by start time end time and interval WorkDay one digit the values lie in the range of 0 to 8 The following table contains the descriptions of each value Value Corresponding day 0 Everyday 1 Monday 2 Tuesday 3 Wednesday iW50 User Manual Version 1 2 23 www orbien co uk Thursday Friday Saturday Sunday COIN O oa s Monday to Friday StartTime and EndTime consists of 4 digits hh mm and works on a 24 hour clock For example 0000 means time 00 00 hh mm 2359 means ti
10. Note Up to 3 periods be allowed per workday Each period time should set by ArmTime DisarmTime WorkDay one digit the values lie in the range of 0 to 8 The following table contains the descriptions of each value Value Corresponding day Everyday Monday Tuesday Wednesday Thursday Friday Saturday Sunday Monday to Friday oO INIIAI AJOIN gt ArmTime and DisarmTime consists of 4 digits hh mm and works on a 24 hour clock For example 0000 means time 00 00 hh mm 2359 means time 23 59 hh mm The iW50 User Manual Version 1 2 34 www orbien co uk ArmTime and DisarmTime should be in the same day and the DisarmTime must be later than ArmTime during the same period Successful SMS reply Set timing defense successfully the parameter is 4 12 3 Disable timing arm the camera Method The user sends following SMS message in order to Disable timing arm the camera 128 0 Successful SMS reply Timing defense de activated 4 13 Auto disarming the camera Description In order to avoid the camera from sending out alarm message all the time the camera can be set auto disarm when it has sent out a certain number of alarms At least one alarm message should be sent via MMS After the user sets this function successfully any alarm of the camera will be counted in alarm times When the user arms disarms the camera manually the counted alarm time wi
11. Note During the process of adding a new remote control if the battery of remote control runs out the camera will emit three Beep tones and exit learning mode You need to replace the battery and repeat the process 4 5 2 Remote control instruction There are three buttons on the remote control A Arm iW50 camera e When is pressed the indicator light on the camera will turn green This indicates that the camera is in armed mode e Any motion detected by the camera will trigger the camera alarm and an SMS MMS or phone calling notification will be sent to the preset numbers B lt gt pdisarm iW50 camera e When is pressed the indicator light on the camera will slowly flash green This indicates that the camera is in disarmed mode e The camera will not detect any motion or receive additional sensor alarm signals C Emergency button e When is pressed the indicator light on thecamera will rapidly flash green The camera will then dial the master user s number Live audio stream can be heard upon answering the emergency call e If the master user does not answer the call the camera will then dial the other emergency numbers as preset order until someone answers the call e The master user s number as well as the emergency numbers will be called a maximum three times If it is still no one answers the call the camera will then exit dialing mode automatically iW50 User Manual Version 1 2 25 www orbien co
12. SMS reply Family number deleted successfully Failed SMS reply Failed to delete family number 3 4 Define guest user Any selected person can operate in the Guest category if they know the password and the iW50 SIM number The Guest user s can then use their mobile phones to send a SMS command including password to the camera in order to obtain an MMS image 3 5 Define emergency number The Emergency Number is the phone numbers which iW50 camera will dial when the emergency button of the remote control is pressed Emergency numbers could be the telephone numbers of family numbers security guards police etc 3 5 1 Add emergency number Authority Master user Description e The master user s number is the default emergency number e When the Emergency button on the remote is pressed iW50 camera will automatically dial the Master user s number followed by the other pre set emergency numbers the default mode is dial phone mode e Each camera can have up to 9 emergency numbers Not including the Master user s number Method The user sends following SMS message in order to Add single emergency number on the camera 106 EmerqgencyNumber Add several emergency numbers on the camera 106 EmergencyNumber 4 EmergencyNumber Note The EmergencyNumber are the phone numbers Successful SMS reply Added emergency number successfully iW50 User Manual Version 1 2 17 www orbien co uk Failed SMS reply
13. as it also erases the values for the master number the remote control as well as the wireless sensor s Method iW50 User Manual Version 1 2 37 www orbien co uk Method 1 Reset via the camera e Switch the camera off It must remain off for a minimum of 20 seconds e Press and hold the set button and then switch IW50the camera back on e The indicator light will be green for 2 4 seconds after which it will flash red e lf the resetting of camera is successful a Beep tone will be emitted Method 2 Reset via SMS command The user sends following SMS message to the camera in order to Reset the camera 08 password Successful SMS reply The GSM camera has successfully reset to its default settings Chapter 5 Advanced settings 5 1 Image settings The user sends the following edit message via SMS to the camera in order to configure the following settings 5 1 1 Image size e For master and family users 32 value e If the value is 1 the image size is 160 x128 pixels It s for a standard small screen mobile phone The size of one MMS image file is 4K e If the value is 2 the image size is 320x240 QVGA default The size of one MMS image file is 9K e lf the value is 3 the image size is 640 x 480 VGA The size of one MMS image file is 33K Successful SMS reply The image size has been reset successfully 5 1 2 Image quantity For master and family users 33 quantity e The default quantity value is
14. horizontal surface Choosing where to position the iW50 m n order to capture better image quality avoid any areas where bright light will be directly into the lens of the camera In order to avoid backlighting photography it is suggested that the camera is placed looking down towards the monitoring area at an 30 angle m The GSM network s signal strength may affect the image live voice quality and MMS transmission speed Therefore upon installation the user should ensure that the iW50 is located in an area with a strong network signal and coverage m After installation it is recommended that a number of test runs be carried out by taking several images and sending to your mobile phone This will allow you to check the image quality and positioning 2 5 Power on off Power on Operation Indicator light Status Turn the power Red light is on for 3 5 seconds ee to On Red light flashing slowly for about Rar 35 seconds A Beep tone will be heard Green light flash slowly or iW50 is disarmed or green light be on constantly armed Power off Turn the power switch to downside Off position 2 6 Quick start Turning on the iW50 To turn on the iW50 simply move the Power Switch on the side of the camera to the ON position The front indicator will turn green showing the camera is on iW50 User Manual Version 1 2 11 www orbien co uk Create a Master user In order to enable
15. orbien co uk CONTENTS F r your Safety eissii sriain kaare apir Tana EEA PAE EENE a aei levessdbies tebesseuacbabetopdadeseaseboesnednger es 6 Exception clase sensnm aeania E E E E O R RO R 6 Chapter 1 Introduction oo ccc cccccsccssesscessessesescsecsecssesssesseseeceecsecsscosseascsessscssesssesssaecaecssesasessessscascaeseseatenss 7 Dod Maii TCL GINS orereta ces Sevan di Ea das cde ce okt caidas EEEE ta ee be donne eedevcsdhi ea etaves ti eee lee 7 12 tW 50 Contents nn R R reich O EE eee aileie eee enleaaeees 8 T3 K ey and pants 5 25 ieee terre Bees eee ieee ee eee eee ee eae 8 1 4 Remote control Instruction ccceseseessesessecseceseeseeeeeeeecsecsecseceeceseeaeeaaesseeseeeeeeaecaesaeeeeeeseesenecaees 9 15 aW50 LED Hight indicator ereere r EErEE ERA EEE EEEE R apie 9 Chapter 2 Getting Started sessar E i EE E EEEE AE iai 10 2 1 Install the SIM card cccccccscccscccsesssecsecescesscecseseseeceesessesesecessesssecseseseeseeecsesesuesesecseeesaesesaeeneesseees 10 2 2 Extending the 1W50 base board ccc cscccasececssacssaseceosvencssaccsasvecasencctaevseesassaseseec ineine isisisi 10 2 3 Connecting to power adapter ce eeseeessseseeeeeeeseeseeseecseeeseeseeceecaecaesersessesseeaesecaeseeeaeeaeeaeaeeateees 10 2 4 Mounting the 1W50 0 3 isc ancieiininedi di ae i adel Ais eed neni 11 2 3 PWET OM Ofira iisen eanes eresie r aa E E EESE EREE tested a ERDE extents aE Testa aes 11 ZO OMICK SIAE aea rE coeds E E R E A 11 Chapter 3 Defi
16. the camera will automatically choose WAP or HTTP to send MMS message Note Your Network Provider will be able to provide you with Network Parameter Settings which can typically be found on their web sites A4 Method The user sends the following SMS message Set MMS center 1244MMScenter Note The MMScenter should be the MMS center address of the Network Provider For example 124 http mms vodafone co uk serviets mms Successful SMS reply Set MMS parameter successfully http mms vodafone co uk serviets mms Set APN parameters 125 GatewaylPHWAPGatewayPort HT TPGatewayPort APNHAPNusername AP Npassword For example 125 212 183 137 012 9201 8799 pp vodafone co uk wap wap Successful SMS reply Set APN parameter successfully 212 183 137 012 9201 8799 pp vodafone co uk wap wap 4 2 Capture images Authority Master family or a guest can send an SMS to the camera which triggers the camera take an MMS image which is then sent to an appointed mobile or Email address Master and family members can call the camera to get the images iW50 User Manual Version 1 2 19 www orbien co uk Master and family can send an SMS command to the camera to send MMS image to an Email address requires pre set E mail address 4 2 1 Capture one image and send to the user mobile Authority Master family and guest users Method Method 1 e Master or family user calls the camera and hangs up upon hearing the ringing t
17. the products described in this document without prior notice 2 For the latest product information please visit www orbien co uk We do not guarantee the document veracity reliability or any content except regulated in proper laws Including no guarantee for product suitable market or suitable area promise 3 Use this product legally Respect people s privacy We hold no responsibility for the illegal use of this product 4 Wehold no responsibility for any loss of data or income or any special incidental consequential or indirect damages howsoever caused For further details about the iW50 or any of our other products visit www orbien co uk iWS50 User Manual Version 1 2 6 www orbien co uk Chapter 1 Introduction 1 1 Main functions This product uses a GSM SIM card It can send multimedia messaging MMS images to MMS enabled mobile phones with color display or to an Email address Remote control Control and configure the camera with short messages SMS commands from a mobile phone Real time audio call the camera number to listen in live voice Motion detection Detect and notify authorized users of any motion in the monitoring area Integrated infrared body detector Sensor detection Allowed to load up to 15 sensors such as door magnet sensors infrared body sensors smoke sensors gas sensors etc Any activated sensor will notify the authorized users via SMS E Infrared light The built in high light infrared
18. uk Successful SMS reply Warn sound mode de activated The camera will not emit any tone upon alarm activation 5 2 3 No SMS notification upon alarm For master and family users 11 0 Successful SMS reply No send SMS when alarm 5 2 4 SMS notification upon alarm Default For master and family users 11 1 Successful SMS reply Set alarm with SMS successfully 5 2 5 No MMS notification upon alarm For master and family users 12 0 Successful SMS reply Set alarm without MMS successfully alarm with SMS only 5 2 6 MMS notification upon alarm Default For master and family users 12 1 Successful SMS reply Set alarm with MMS successfully 5 2 7 No call notification upon alarm Default e Formaster and family users 13 0 Successful SMS reply Didn t auto dial calls when alarm 5 2 8 Call notification upon alarm For master and family users 13 1 iW50 User Manual Version 1 2 40 www orbien co uk Successful SMS reply Auto dial calls when alarm e If the camera alarms automatically it will dial the master user s number Live audio stream can be heard upon answering the call e lf the master user does not answer the call the camera will then dial the family user s numbers in the preset order until someone answers the call e The master user s and the family user s numbers will be called a maximum three times If it is still no one answers the call the camera will the
19. 0 camera with his her mobile phone The camera will notify the user that the number is currently busy and this indicates that the user s mobile number has been recognized as Master number Method 2 The user must edit and send the following SMS to camera via his her mobile phone the phone number will be the Master number in order to iW50 User Manual Version 1 2 14 www orbien co uk Add a master number to the camera 00 Successful SMS reply Welcome to the GSM Remote Camera Your password is 1234 Failed SMS reply If a user tries to activate the camera again by using method 1 the camera will hang up the call No notification message via SMS will be sent to the user By using method 2 iW50 camera will send a notification via SMS stating Master user already exists 3 2 2 Change the master number Authority Master user Method The user sends following SMS message in order to Change the master user s number 14 NewMasterNumber Successful SMS reply New master number is The old master user s number is no longer able to control iW50 camera 3 2 3 Change password Authority Master user Description In order to ensure your privacy and safety during the use we recommend that the camera password is changed Method The user sends following SMS message in order to Change the password 04 o ldpassword newpassword e The password is a four digit number e The original password is 1234
20. Before installing your Sim card please ensure that MMS is enabled and PIN protection is disabled You may need to use an existing mobile to ensure these settings or contact your network provider If you have a Contract Based Sim card the iW50 will auto sense and apply the correct network settings 2 2 Extending the iW50 base board Hold the base of the camera and pull the top part and the bottom part base in opposite directions i e away from each other Then the slot buckle will be pulling open The head of the iW50 camera can now be moved freely and located at any direction 2 3 Connecting to power adapter Connect the adapter to an AC power and connect the mini USB plug to the power interface of the camera The iW50 has a built in rechargeable Lithium battery The iW50 will notify the user when the power changes For example if the power adapter is disconnected or failure of the AC power occurs the camera will send an SMS External power cut The device is operating on battery If the iW50 is again connected to the external power or the AC power is available again the camera will send an SMS The device is now resuming the use of external power source Note The configuration setting cannot be saved when the camera is operating on low iW50 User Manual Version 1 2 10 www orbien co uk battery 2 4 Mounting the iW50 The camera can be mounted on a wall vertically with the screws or placed on any suitable
21. LED s allows the camera to capture clear images even in dark environments or areas with insufficient lighting m High quality camera 300 000 pixel CMOS camera in order to obtain a clear image via MMS E Send images to mobile phones The camera will send MMS images to your mobile You can check on the monitored areas at anytime and anywhere providing there is GSM GPRS network coverage and MMS service coverage E Send images to Email The camera can send images to preset available Email address Multi mode alarm The camera can send alarm messages via SMS MMS Email m Fixed time monitor The monitoring schedule can be set with multiple time intervals m Easy installation No software downloads or wires needed the iW50 is a wireless full portable device Accessories Includes 2 remote controls with panic arm and disarm buttons Built in lithium battery Rechargeable battery ensures operation of iW50 camera during external power failures iWS50 User Manual Version 1 2 7 www orbien co uk 1 2 iW50 contents 1 iW50 GSM remote camera 1 unit 2 Power adapter 1 unit 3 Remote control 2 units 1 3 Key and parts 1 SIM card Slot rubber cover 7 Power Interface Mini USB 2 Camera 8 Line Holder 3 Infrared lights 8 lights 9 Slot buckle 4 Microphone 10 Hanging hole 5 Indicator 11 Setting key 6 Power switch 12 Base board 13 Infrared body detector Tip Keep the camera lens clean to insure best imaging quality
22. TILY oo ec eeesetesseecseeeeseseeecsesecaesesaesesecaesesaeaesecaessaeaeeecaeeessesesacaescaetesseeeeecaeeeeetaees 38 51 3 a ta a 1 8c See ee eee 39 5 2 Automatic alarm Settings sccccsccicestsscccececuesctvesscastsceaxessevenscteusbestostetstunsateeeotsdescessnsrnsnsnteieracten teeters 39 5 2 1 Warning tone UPON alarm triggering cecesseccseesesenseecseeeeseseesceeeeeseseeseneesceeteeseaeeecaeeeeeenees 39 5 2 2 No warning tone upon alarm Default 00 ccc ececcecseeseeseseeseeseeseseeseesesseeseseeseeseseceesseeeaes 39 iW50 User Manual Version 1 2 4 www orbien co uk 5 2 3 No SMS notification UPON AlarM cccccccscsscescessessecsecsecsscescescesscsscsseeaecescessessessesseesseateaes 40 5 2 4 SMS notification upon alarm Default oo cee cesenseeceeeseseeeeeceeeeeseeeseeeeceecesseeeecaeeeeetaees 40 5 2 5 No MMS notification UPON alarm 0 0 ce cecesessescesceececseceeeessessesaeeeesecseeecesesseseeseeeeeeseeeesesaes 40 5 2 6 MMS notification upon alarm Default ccc ccccseeeeseseeseeseesesseseeseesesseseeseeseeecsecseeeeaes 40 5 2 7 No call notification upon alarm Default oo cc sesseecseseeseneeeceeeeseeeseeeeceeeesseeeecaeeeeeenees 40 5 2 8 Call notification UPON AlALM ccccccscesccsccssesscesceeecsccsecsecsecsecessesscssecsecsecescessessessesseessenseaes 40 5 2 9 No MMS notification to pre set E mail address Default 0 0 eee ceeeeceeeeeseeeeeceteeeeeees 41 5 2 10 MMS notification to pre set E mail addr
23. YES YES NO Note Any MMS enabled mobile phone can receive the images captured by the camera by sending SMS command with password Any SMS enabled mobile phone can control the camera with the password command iW50 User Manual Version 1 2 13 www orbien co uk All the settings of iW50 camera can be set or adjusted via a SMS command Introducing SMS Commands 10 Master and families user use the following SMS command format code content 20 Guest users use the following SMS command format code password content 30 The password must be a four digit number 40 The original password is 1234 50 The maximum digits that are allows for the phone number is sixteen 6 iW50 camera will reply to the user after it receives the SMS command Note The symbol must not be ignored when typing an SMS command and the must not be any space within the commands 3 2 Define master user to start the camera In order to enable all the functions on the camera the Master user must store his her mobile number in the camera s memory Only one Master s mobile number Master number is allowed for a camera 3 2 1 Add a master number to the camera Authority Master user Description If iW50 camera is being used for the first time or iW50 camera has been reset the master user s number must be programmed into the camera in order to ensure activation The following methods can be used A4 Method Method 1 The user must call iW5
24. agvest RA in peau atreatests Hanes 34 4 12 1 Enable timing arms the camera oo eececceccsesseseseeecseseecesceeceescecescneceeseceesenaeseeecatacnaeaeeeeeeaes 34 4 12 2 Set time period to arm the camera occ ccceceesessessesceseeececsecseeeeseesessecseeeeseesesesseeeaeenens 34 4 12 3 Disable timing arm the camera ceeeeeseeeseseeseseeecseseeceseeeceesceceaceeceesenacsesaesceecaeseeaeaeeeeeeees 35 4 13 Auto disarming the Camera ccccccceesessesescesceseeeeeeeecaecseceecesceseesaesaeseeeseeeeaecaesaeeeserseeeeaeeaeees 35 4 13 1 Activate auto disarming the CAMEL ee cesseseceecseseeseseecseseeseseeeceeseseeseeceseeeceeseseeeeeeeeeees 35 4 13 2 Disable the function of auto disarming the camera default ccc cccseeseeteeeeeteees 36 4 14 Camera language Setting ccccceeessesseesecsecescesceseeeeecaecseceeseeceseeaeesaesseseseeeeaecaeseeeeeereeeeeaeeseens 36 AISO heek SAMS eenn c ec sae canvas coo E avon cots en scues fps cate A ete 36 4 16 Getting help csiiccct ast cccticven vatican a E E E EE E EERE 37 4 17 Resetting the camera i scsstssesspascerists eesti ties erie ER arrea EEA esau RERA EE venient eteel 37 Chapter 5 Advanced SettingS cccccssssssssssscssssesseesssscsscsesseseesessesessesscsessesesuscsecsesessesnssnscsesessesansesansass 38 5 1 Image s tting Saresti erran eaaa EEEa aN stted cao Ea eanas PE AONANE EEUE ENA quensstetsnenngnieaenieediors 38 5 1 1 Image SIZE ganna a ee es A EE a Ee ee EE 38 5 1 2 Image QUAN
25. all the functions on the iW50 a Master user must be created A Master user is the mobile phone number of the primary user and this mobile phone number must stored in the camera s memory Only one Master s mobile number Master number is allowed for a camera If using the camera for the first time or following reset create Master user by Calling the iW50 with you mobile phone On connecting you will hear that Sim number is busy or a message asking you to leave a voice message indicating that the mobile number has been recognized and set as Master number Following Master number set you will get the following SMS Message Welcome to the GSM Remote Camera Your password is 1234 This message indicates that creating Master number has been successful Capture your first picture Contract Based Sim To capture your first picture 1 Simply call the iW50 using the mobile phone used to create the master number and hand up on hearing the ringing tone within 5 seconds The iW50 will send you an SMS notification Your request received iW50 is sending the MMS image Soon after this you will receive an MMS message containing the picture If this does not work then the iW50 has not been able to auto sense the network settings associated with your Contract based Sim and you will need to apply the APM amp MMS settings manually See section 4 1 Network parameter settings to manual apply Pre Paid PAYG Sim network settings and in so
26. d chapter 5 1 2 Image quantity when alarm When the camera is operating on low battery the infrared body detector will be deactivated and the configure setting cannot be saved 4 9 Motion detection Description e The motion detection feature is based on image frame compare technology The firmware will compare front and after images which capture from camera and iW50 User Manual Version 1 2 28 www orbien co uk therefore detect motion e The motion detection feature only functions when the camera is armed e The motion detection feature is also functional when the camera is in its default setting e When the motion detection alarms the notification pictures will be sent on one message via MMS The default quality of individual picture is 5 and the size is 320x240 pixels In order to change the setting see chapter 5 1 1 Image size and chapter 5 1 2 Image quantity when alarm Note Ifthe camera faces an object that moves constantly such as a tree shaking in the wind it will send alarm message constantly It is recommend that the camera is pointed away from such objects The motion detection function will be deactivated and the configure setting cannot be saved when the camera is operating in low battery 4 9 1 Activate Deactivate motion detection Authority Master and family users Method The user sends following SMS message in order to Deactivate motion detection 22 0 Activate motion detection 22 1 Successful SMS re
27. e size of the pictures is pre set by user See 5 1 1 image size The interval between the pictures is default 0 5s and can be pre set by user See 5 1 3 image interval 4 2 3 Capture images and send to user s Email address Authority Master and family users Description If the master or family user wishes to send the images to his her Email address the Email address must first be setup See chapter 4 3 Email settings for more information regarding this function Method The user sends following SMS message in order to Capture image s and send to pre set E mail 03 maqeQuantity 1 Note Image quantity should be in the range of 1 8 when the image size is set at 160x128 or 320x240 Image quantity should be in the range of 1 2 when the image size is set at 640x480 Successful SMS reply Your request received iW50 is sending the MMS image 4 2 4 Capture images and send to an appointed mobile or Email address Authority Master family and guest users Method In order Capture image s and send to appointed mobile or Email address the user sends the following SMS message For Master and family user 30 NumberOrEmail lmageQuantity For Guest user 30 Password NumberOrEmail imageQuantity Note NumberOrEmail should be the mobile phone number or E mail address which iW50 User Manual Version 1 2 21 www orbien co uk the user appointed to send image mage quantity should be in the range of 1 8 when the image size is
28. ess 0 00 cece ccccescescessessessecsecsscessessessesseeseenseaes 41 5 3 Turn on off LED indicator on the camera ccccccccesecsscesseesseceecesseecseceacesseecesesseeseecaeseaeceaeeeseesss 41 5 4 SMS notification upon the power supply changing s essesesssssesesesseesesessessrsrsessresesessesessesesesses 42 Chapter 6 Maintenance ccccccccsccssessesscessesssceecsecssesscessessecesesecsecescssceascssssucsacensssssesesesssesaesasensseasenesaees 42 Chapter 7 General troubleshooting ss ssssssesssseesesesesesesssesreessesersseresesensststsestsestsrstssstinesesesestsesnsreenesesrene 43 Chapter 8 SMS command liStasssncisasunensirniansnn nne a E AIER E a ERRER 44 iW50 User Manual Version 1 2 5 www orbien co uk For your safety Em This product is a wireless signal transmission device Keep it away from electronic equipment that is likely to interfere with the wireless signal and connection to the mobile network E Switch off the iW90 and mobile phone when entering areas marked Explosive Might explode Do not place camera in a fire as this may cause the battery to explode This product should only be charged and powered using the provide power leads and charger The use of any other types of power may damage the product m Keep the product and its accessories out of reach of children Exception clause 1 We operate a policy of continuous development We reserve the right to make changes and improvements to any of
29. ll be cleared to 0 4 13 1 Activate auto disarming the camera Authority Master and family users Method The user sends following SMS message in order to Activate auto disarming the camera 138 1 Set the value of alarm times when the camera is auto disarming 139 times e The times should be numbers Successful SMS reply e Cancel defense after warn some times activate e Cancel defense after warn times iW50 User Manual Version 1 2 35 www orbien co uk e When the alarm times reach to the times value setting the camera will auto disarmed and send SMS message The device has been auto disarmed 4 13 2 Disable the function of auto disarming the camera default Authority Master and family users Method The user sends following SMS message in order to Disable the function of auto disarming the camera 138 0 Successful SMS reply Cancel defense after warn some times deactive 4 14 Camera language setting Authority Master user Description The camera supports both English and Spanish display Method The user sends following SMS message in order to set Spanish version 127 0 English version 127 1 Successful SMS reply Set version successfully 4 15 Check status Authority Master family and guest users Method The user sends following SMS message in order to Check the present settings and work status of the camera e For master and family users 07 e For guest user
30. me 23 59 hh mm The StartTime and EndTime should be in the same day and the EndTime must be later than StartTime IntervalTime This consists of 2 or 3 digits and has values in the range of 10 to 480 minutes Successful SMS reply Set timing to send MMS parameter is 4 4 3 Disable timing send MMS image Method The user sends following SMS message in order to Disable timing send MMS image 115 0 Successful SMS reply Set timing to send MMS de activated 4 5 Remote control 4 5 1 Add remote control s to the camera Description When a remote control is added to one camera then that remote control and control the camera A camera can have up to 5 remote controls added Method Indicator Operations Status Green flashing or 1 Press and hold the Set key Indicator light turns to orange constantly light for 2 seconds Learning mode f 2 Press any button on the The camera will emit a Beep Orange flashing nde l remote control with battery tone and indicator will turn green iW50 User Manual Version 1 2 24 www orbien co uk inside to send a signal to the for 2 seconds Added camera successfully f 3 Repeat step 2 to load Orange flashing another new remote control 4 Press the Set key to exit Indicator light turns green Orange flashing the learning mode or wait for flashing or constantly light Exit 15 seconds to auto exit learning mode
31. me cases the Contract Sim network settings Notes 1 In most cases a Pre Paid PAYG Sim will be sensed by the camera and settings automatically applied but this is dependant on the mobile network providing using the same network settings for Contract and Pre Paid Sims 2 There may be a delay in receiving your MMS depending on the Network Provider If you had any problems in completing any the Quick Start steps then please follow the next Chapters iW50 User Manual Version 1 2 12 www orbien co uk Chapter 3 Define the user 3 1 User authorization level There are three levels each with a different authorization level namely Master Families and Guest Table 3 1 the difference in authority for Master Families and Guests users User Type Master Families Guests Functions Change authority password YES NO NO Receive SMS YES NO NO Automatic Receive MMS YES NO NO Alarm Receive alarm calling YES YES NO Get images by Email YES NO NO Receive SMS YES NO NO Emergency Receive MMS YES NO NO alarm Receive emergency calling YES YES Only emergency number Call the camera to listen in live voice YES YES NO Get work status images help and YES YES YES Password instruction by sending SMS command Get images by Email YES YES NO Set remote camera by SMS command YES YES NO Add modify or delete sensor YES YES NO Camera language setting YES NO NO Set infrared body detect function
32. mily status of the camera 07 password Guest Master Getting normal 09 ae Family command list via SMS Getting 09 password Guest help f Master Getting detailed 09 1 i f Family instruction via MMS 09 password 1 Guest Reset the camera 08 password Master Image Master Image size 32 value settings Family ee Ha a H MA A iW50 User Manual ersion 1 46 www orbien co uk Family p Master Image Interval 103 time i Family Warning tone upon Master l 130 1 alarm triggering Family No warning tone upon Master alarm Default Family No SMS notification Master upon alarm Family SMS notification upon Master alarm Default Family No MMS notification Master Automatic upon alarm Family alarm MMS notification upon Master 12 1 settings alarm Default Family 13 1 No call notification upon Master 13 0 alarm Default Family Call notification upon Master alarm Family No MMS notification to f Master pre set E mail address 110 0 f Family Default MMS notification to Master i 110 1 pre set E mail address Family PS Master Turn off indicator 143 0 f Family Lights aes Master Turn on indicator 143 1 Family SMS notification upon th l 144 1 Vane e power su SMS p i PEY Family nate changing Default notification No SMS notification and reply Master upon the power supply 144 0 Family changing iW50 User Manual Version 1
33. mily users Description e When the camera is armed all the loaded sensors infrared body detector and motion detector are in work status The camera will automatically send alarm message or make a phone call if any one is triggered e When the indicator light on the camera is slowly flashing green it shows that the camera is disarmed Use following methods to arm the camera Method Method 1 The user sends following SMS message in order to Arming the camera manually 01 Method 2 Press on the remote control whilst pointing it in the direction of the camera The camera will emit a Beep tone to indicate that arming of the camera is successfully Method 3 The user calls the camera and hangs up within 5 20 seconds upon hearing the ring tone The camera will be armed or disarmed iW50 User Manual Version 1 2 32 www orbien co uk Successful SMS reply Defense mode activated And the indicator light will turn green not flashing 4 11 2 Default arming mode e In this mode the infrared light will be on e When motion is detected a notification will be sent via SMS to preset user numbers Five notification pictures will be sent on one message via MMS MMS image quality is 320x240 QVGA e When the integrated infrared body detector and loaded wireless sensor triggers the camera a notification will be sent via SMS to preset user numbers Five notification pictures will be sent on one message via MMS MMS image size is
34. n exit dialing mode automatically e If SMS MMS and calling notification are all activated when the camera alarm automatically it will firstly send an SMS secondly an MMS and thirdly a calling notification to preset users 5 2 9 No MMS notification to pre set E mail address Default For master and family users 110 0 Successful SMS reply Alarm didn t send MMS images to email 5 2 10 MMS notification to pre set E mail address For master and family users 110 1 Successful SMS reply Alarm set with MMS notification to an E mail address successfully e If the MMS notifications is set to be send to both a mobile phone number as well as to an e mail address the MMS image will firstly be sent to the mobile phone number and then to the E mail address 5 3 Turn on off LED indicator on the camera Authority Master family user Description If the LED indicator is on it will display in different ways to show the working status If it turns off it can make the camera private and avoid to be found easily Method The user sends following SMS message in order to iW50 User Manual Version 1 2 41 www orbien co uk Turn off indicator 143 0 Turn on indicator 143 1 Successful SMS reply Status LED close Status LED open 5 4 SMS notification upon the power supply changing Authority Master and family user Method The user sends following SMS message in order to set SMS notification upon the power suppl
35. ne the USE scc ccicccceicetesessecssesieecverecnevsesnessucessoessdesevesscasccbes E ATA T EE 13 3 1 User authorization level ccccccccccccsssessecsscesssecseeececscesseeesecsescsaeecseceeeesuescsesesaeeeesesaeseaeseateneeees 13 3 2 Define master user to start the camera ssssssssssesessesseessststsrsstseresteesesseststtstsesseeesesseseseesesesses 14 3 2 1 Add a master number to the camera s s sseessssesesesessserisesertstststsrsssrereriesisesrsrstsrsesrsrersene 14 3 2 2 Change the master number essssssssesesesesesesesrsessserersssresesesesesestsesssrsrereesesesesesesesssesesesese 15 3 2 3 Change PASSWOIC L cc ccecccccesseseesesseseessesceseecesseseeecsecsecaecaesessessesaesaeaessecaeeeceaesssaesseeeeeeseesaesaeaes 15 3 3 De tine family USOlsrac cc scseceesveetssaeviaseeatvescciateqeetiets ees n aa a p E E Ee EEE a EEEE 16 3 3 1 Add a family NUMbEr o oo eee ceceeesccsceseesceceseeseeececsecaecaeceesessessesaeaessecsesaesaesaesecseeeseesaeeaeeaeees 16 3 3 2 Check family user s NUM eET occ esseecseeeeseseeecseeeeseseeecaeseeseseeceeeeseseecaseecaeeesseneeecaeeeeaeaees 16 3 3 3 Delete family NUMDET ccccesecsessescesceseesesseseessesesscsecsessesessessesssssessesesaesaesseseeaeeaeeeseseseasegs 16 BA Define Guest User fe occ catecke a reae RRE EErEE EREA EEO EEE EAEEREN EE 17 3 5 Define emergency mUMber aicen ea R E E E R R E 17 3 5 1 Add emergency nUMber ue eee eseseseescseecseeeeseseecseseesenesecaesse
36. ode 4 7 3 Listening in upon automatically alarm Description iW50 User Manual Version 1 2 27 www orbien co uk e When the camera is in the armed status and if the user preset the auto alarm Refer to chapter 5 2 8 Call notification upon alarm for the details of preset alarm a Call will automatically go through to the Master user s preset numbers when the camera alarms The user can then listen in the live audio picked up from the cameras microphone e lf the Master user does not answer the call the camera will dial the other pre set Family number until the call is answered This notification process will be repeated three times and if still unanswered the camera will automatically exit the dialing mode 4 8 Infrared body detector Authority Master and family users Description When the camera is working under arming mode if someone approaches to the detecting area the built in infrared body detector will trigger the camera alarm Method The user sends following SMS message in order to Activate infrared body detector default 118 1 Deactivate infrared body detector 118 0 Successful SMS reply Infrared body detector activated Infrared body detector deactivated Note When the infrared body detection alarms the notification pictures will be sent on one message via MMS The default quality of individual picture is 5 and the size is 320x240 pixels In order to change the setting see chapter 5 1 1 Image size an
37. one within 5 seconds e iW50 camera will reply with an SMS notification Image capturing request received The camera is busy sending the MMS messages e The user will then receive the MMS message e The guest users are unable to capture an image by using Method 1 If the guest users Calls the camera it will neither send a notification message nor an MMS message Method 2 In order to captures one image the user sends the following SMS message For master and family users 03 For guest user 03 password 4 2 2 Capture images and send to the user s mobile Authority Master family and guest users Method In order to capture multiple images the user sends following SMS message For master and family users 03 IlmaqeQuantity For guest users 03 Password ilmageQuantity Note Image quantity should be in the range of 1 8 when the image size is set at 160x128 or 320x240 See 5 1 1 image size The default image size is 320x240 QVGA Image quantity should be in the range of 1 2 when the image size is set at 640x480 Successful SMS reply Your request received iW50 is sending the MMS image e The user will then receive the MMS message iW50 User Manual Version 1 2 20 www orbien co uk e The file format of the sent MMS images is Model Time jpg For example a file with name of iW50 094843 jog means the image is captured with a iW50 camera at 9 48 43AM e Ifa sent MMS file has several sequential pictures th
38. orking active insufficient fee of the SIM i add credit to the card card SIM card no install properly Indicator constant light i 3 Can t find or identify the SIM card Power off the camera and in red color check it again Camera didn t Switch off the power check 4 response of any iW50 camera work abnormally SIM card or reset default operation setting A Place the camera at other i Network signal weak or network i After starting the b place with strong signal and usy camera indicator 4 try again 5 flashed in red color f f SIM card PIN code active Deactive the PIN code and does not turn to green f i Contact with local operator to SIM card invalid check it Connect external power to Camera low power recharge the battery Remote control does Change remote control not work Or action Remote control low power bati attery i oiy Greant Pull out remote control distance range Didn t pull out the antenna antenna shortened Two remote control work Try only one remote control simultaneously The remote control or sensor i Exit the loading status already studies successfully Can t add new remote The sensor quantity has already Delete old sensors before add 7 control or wireless Sio reached its max number new sensor Didn t set master user number Set master number before add sensor Can not start the Battery runs out of power Connect the camera to 8 camera after long time external AC po
39. ply Motion detection de activated Motion detection activated 4 9 2 Send five Images upon motion detection alarm Authority Master and family users Description The camera will send out 5 images with fixed size of 160x128 pixels when motion is detected Method The user sends following SMS message Send five images upon motion detection alarm 142 1 iW50 User Manual Version 1 2 29 www orbien co uk Cancel send five images of motion detection alarm 142 0 4 10 Wireless sensor s Authority Master and family users Description Any 433MHz wireless sensor such as infrared body sensor wireless door magnet wireless smoke detector etc can be set as an alarm sensor of the camera 4 10 1 Add a wireless sensor and set corresponding alarm mode Authority Master and family users Description e Up to 15 wireless sensors can be loaded onto one iW50 camera Method 1 Power on the wireless sensor 2 The user sends following SMS message to Make the camera enter loading mode and set corresponding alarm mode 05 SensorDescription e Sensor description is used to identify different sensors affiliated with each camera It can be numbers and letters e Sensor description could be empty If SMS command is only 05 the camera will recognize the sensors in number order been added to the camera For example if the camera has been added 2 wireless sensors it can recognize a new sensor with a sensor description of 3 automa
40. s 07 password Successful iW50 User Manual Version 1 2 36 www orbien co uk SMS reply e The camera will reply via MMS depending on which status is currently set on Such as Device dis armed No SMS notification when alarm is triggered No MMS notification when alarm is triggered Motion detection de activated Timing send MMS de activated Infrared light on off Image size 160x128 320x240 640x480 Send image quantity when alarm Master number Master email Family email Wireless sensor Emergency number Language version 4 16 Getting help Authority Master family and guest user Description The user can send an SMS to the camera in order to get the SMS command list the command description as well as the codes Method The user sends following SMS message in order to Getting normal command list via SMS e For master and family users 09 e For guest users 09 password 4 17 Resetting the camera Authority Master user Description e This function resets all programmed settings to their original values e After the camera is reset it will need to be restarted The remote control as well as the wireless sensor will also need to be reloaded Refer to chapter 3 2 Define Master user to start the camera e After resetting the camera However if the MMS function does not work the MMS parameter will need to be reset Refer to chapter 4 1 Network parameter settings Note This function needs to be used carefully
41. s he she will be able iW50 User Manual Version 1 2 26 www orbien co uk to listen in the live audio Emergency Modez2 To send a notification via SMS and MMS to the master user as well as the pre set emergency numbers When the emergency button is pressed on the remote control the camera will send the notification via SMS and MMS to the master user as well as the pre set emergency numbers Method The user sends following SMS message in order to set Emergency Mode1 39 0 Emergency Mode2 39 1 Successful SMS reply Alarm by dialing emergency number has been set successfully Alarm by sending SMS and MMS has been set successfully 4 7 Listen in live voice 4 7 1 Call the camera to listen in Authority Master and family users Method The user calls the camera after which it will answer automatically The user can then listen in the live audio picked up from the cameras microphone Only one line can be connected to the camera at a time 4 7 2 Listening in upon emergency alarm Description e When the camera is in arm or disarm status it will automatically dial the Master user s phone number if the emergency button is pressed The Master user can listen in by answering the call e lf the Master user does not answer the call the camera will automatically dial the other emergency numbers sequentially This notification process will repeat three times and if still unanswered the camera will automatically exit the dialing m
42. seaesecaeeseseseeaeneeecaeeesseaeeecaeaeeeeaees 17 3 5 2 Delete emergency NUMDEM c ec cceecccceceseesessessescescsecsecseceeseesessessessesseseesesaesasseesseseeeseesseeseaes 18 3 5 3 Check emergency NUMDET eceeccecccescescesessesceeceecsecaecseceesesseesesaeseesscsecseesesseaesseeeeeeseeaeeaeaes 18 Chapter 4 Basic use and settings eee cceccscesseseesseecsecseesessesessesaescesecseescsecsecsecaecssessecsecsecseseesesseeasaes 18 4 1 Network parameter SettingS ccccceesseseeseeseneeeeescesceeseeseeeseeceecaecaeeeseeseesaceaeaaeaeeateaesaeaeaeeateeees 18 4 2 Capture TMA GOS serer ener aa EE E deed R R ET E E EEEE etree 19 4 2 1 Capture one image and send to the user mobile ss sssssssssssessseeesesesssesrssssresseresesesese 20 4 2 2 Capture images and send to the user s mobile 0 ees ceteeseseeeceeeeceseecesceeceeseeeeaeeeeeeees 20 4 2 3 Capture images and send to user s Email AddreSS eee ccccesecseseetecseeeeeeeeeseeseseeaeeeees 21 4 2 4 Capture images and send to an appointed mobile or Email address ccceeseeees 21 4 3 E mail Setting Siena endian edaii een R E ences onan E SE 22 4 3 1 Add modify an E mail AddreSS 0 ccccccecesseseesesseseesceseeeceecsecaeeessessecaeceecesseseesaesaeaeeaeeaees 22 4 3 2 Delete all E mail address es oo ccc cccccccesessesseseeseseseeseeseeecsecsecseseeessecaecseceesessessenasesaeerees 22 iW50 User Manual Version 1 2 3 www orbien co uk 4 4 Timing
43. send images to Mobile ceeeceececscsescescesceseeeeecsecseceecesceseeseesaesaeeeeseeeeaeceecaeeeserseeeeaeeaeens 23 4 4 1 Enable timing Sends MMS images ceccecssssesesseesseseeseseeeceeseecescneceeseceesenaeaceecaeaeeaeaeeenaees 23 4 4 2 Set time period to send MMS images 20 0 eeeeesseesseseesesceecseseceseneceesceaescsaeaceeceeseeaeseeeeeeees 23 4 4 3 Disable timing send MMS iMage ceccesessssesesseecseeeeseseeecsescecesceeceeseeaesceceeceeceeaeeaeeeeeeeees 24 AS Remote Conto leaena E EO wt Bouse cestiwm dda eis takes SR 24 4 5 1 Add remote Control S to the camera ue ccccccseseesessesceseescecsecseeeeseeseesecseeeesessesseaeseesaeeees 24 4 5 2 Remote Control instruction oc ecceeseescesecescsesenseseeecsescececceeceeseeaeseneceeeecaeseeaeaceecaesenaeaeeeeeeees 25 4 5 3 Arming or disarming SMS notification ccc cccecsessescesceeceecsecseeeeseesessecseceeeessessessesaeseseens 26 4 5 4 Remove remote control from the camera ce ececseecseeseseseeecseeeseseeeceesenaesencesceecaesceaeseneeeeees 26 A 6 Emergency alarms RE E EE ERE detainees E 26 4 7 Listen in live VOICE cececcssseeseceecesseesseceesesseecseseseeceesesseccseceseesseessesessesseecsssesuesesecsusecsesesaeeeeesseees 27 4 7 1 Call the camera to listen M ssssissssssesresrsreicoscresioikersnesrreeisosdiesisest eseis esiseeissrsseontsse 27 4 7 2 Listening in upon emergency ALAM ccc ccceesseseesessesceeeeececsecseeeeeesecsecseeeeeeeseeeeseeeseeeees 27
44. set at 160x128 or 320x240 The default image size See 5 1 1 image size Image quantity should be in the range of 1 2 when the image size is set at 640x480 Successful SMS reply Sending to with pictures e The file format of the sent MMS images is Model Time jpg For example a file with name of iW50 094843 jpg means the image is captured with an iW50 camera at 9 48 43AM e If a sent MMS file has several sequential pictures the size of the pictures is pre set by user See 5 1 1 image size The interval between the pictures is default 0 5s and can be pre set by user See 5 1 3 image Intervals 4 3 E mail settings Note This function should be supported by your local network provider Please contact your local network provider for the details concerning this function 4 3 1 Add modify an E mail address Authority Master and family users Description Master and family users can assign only one Email address to their user number If more than one Email address is assigned to one user number then the camera will only recognize the last Email address assigned If the user wishes to capture an image and sending to his her Email address see 4 2 3 capture images and send to user s Email address If the user wishes the camera to send the alarm image to his her Email address see 5 2 10 MMS notification to pre set Email address Method The user sends following SMS message in order to Add modify an E mail address 108
45. ter detector 118 0 detector Family Deactivate motion Master 22 0 gt detection default Family Activate motion Master i 22 1 detection Family Motion _ Send five images upon Master detection l 142 1 motion detection alarm Family Cancel send five images Master of motion detection 142 0 Family alarm iW50 User Manual Version 1 2 45 www orbien co uk alarm loading mode and set Family corresponding alarm mode sensor Remove a wireless cae a Master 112 SensorDescription SensorDescription sensor Family Remove all wireless Master sensors Family N Arming the camera Master 01 manually Family Disarming the camera Master 02 manually Family Enable timing arms the Master 128 1 camera Family Set time period to arm 129 WorkDay ArmTime 1 DisarmTime1 4 Ar Master the camera mTime3 Disarm Time3 Family Arming or Disable timing arm the Master disarming 128 0 camera Family the camera Activate auto disarming Master 138H 1 l the camera Family Set the value of alarm F i Master times when the camera 139 times i i Family is auto disarming Disable the function of F Master auto disarming the 138 0 i Family camera The user s first language language or Spanish 127 0 Master setting version English version 127 1 Master Check the present Master Check O7 settings and work status Fa
46. the door once to send the signal to the camera When the camera receives the sensor signal it will emit a Beep tone and send a notification message via SMS to the user s stating has been successfully loaded To exit the loading mode manually press the set key of the camera The camera will emit a Beep tone and exit the loading mode Failed SMS reply If the camera failed to load the sensor the indicator light on the camera will flash red and green alternately for approximately 60 seconds The camera will revert back to the preset armed disarmed mode Once the maximum number of sensors are added if a user attempts to load one more sensor onto the camera the camera will send a SMS message Sensor list is full Please delete old sensor at first The camera will emit Beep Beep tone if the user want to load an existed sensor which has been loaded onto the camera iW50 User Manual Version 1 2 31 www orbien co uk 4 10 2 Remove wireless sensor Authority Master and family users Method The user sends following SMS message in order to Remove a wireless sensor 112 SensorDescription 4SensorDescription e Sensor description should be the existing sensor which the user wants to remove Remove all wireless sensors 112 Successful SMS reply Sensor deleted successfully 4 11 Arming or disarming the camera manually 4 11 1 Arming the camera manually Authority Master and fa
47. tically When the sensor triggers the camera will alarm then the camera will send out SMS alarm message only e Up to 15 characters can be typed in sensor description Set the sensor alarm mode e If you add at front of sensor description the camera will send out MMS and SMS alarm message For example 05 door2 when door2 sensor triggers the camera iW50 User Manual Version 1 2 30 www orbien co uk alarm the camera will send out SMS and MMS alarm messages Otherwise if the first character of sensor description without the camera will send via SMS only Forexample 05 door1 when door1 sensor triggers the camera alarm the camera will send out SMS alarm message only If the sensor is set send alarm via SMS only when it alarms by this command successfully the user can not use following commands to change alarm way of the sensor No SMS notification upon alarm SMS notification upon alarm Default No MMS notification upon alarm MMS notification upon alarm Default 12 1 When the camera has received the SMS command it will emit a Beep tone and the indicator will flash red and green alternately The camera will then send a notification message via SMS to the user s stating Waiting to load wireless sensor make the sensor work immediately The user needs to make the sensor work and transmit the signal to be captured by the camera For example Fora wireless door magnet open and close
48. uk e When is pressed the camera could send a notification via SMS and MMS instead of making phone calls this is dependent on the setting Refer to 4 6 Emergency alarms 4 5 3 Arming or disarming SMS notification Authority Master and family users Method The user sends following SMS message in order to set No SMS notification message upon arming or disarming the camera via remote control 137 0 Send SMS notification message upon arming or disarming the camera via remote control 137 1 4 5 4 Remove remote control from the camera Authority Master and family users Method The user sends following SMS message in order to Remove all remote controls from the camera 111 Successful SMS reply All remote control deleted successfully 4 6 Emergency alarms Authority Master and family users Description When the emergency button on the remote camera is pressed the camera will go into emergency mode to alarm There are two emergency alarm modes Emergency Mode Default To dial the master user s number as well as the pre set emergency numbers When the emergency button is pressed on the remote control the camera will dial the master user s number as well as the pre set emergency numbers The camera will repeat this process 3 times until someone answers If after 3 attempts there is no answer then the camera will automatically stop dialing and revert to its preset mode In the case of someone answer
49. wer and charge supply with the battery for at least one hour then restart camera Note If the problem cannot be solved with above guidelines then contact your local iW50 User Manual Version 1 2 43 www orbien co uk distributor or email info orbien co uk Chapter 8 SMS command list Add a master number to 00 Master the camera Change the master 14 NewMasterNumber Master user s number Change the password 04 0 ldpassword newpassword Master Add a family number 06 FamilyNumber Master Add several family 06 FamilyNumber FamilyNumber Master numbers Delete a family number 113 FamilyNumber Master Delete several family 113 FamilyNumber FamilyNumber Master numbers simultaneously Define the Delete all family user Master numbers Add single emergency 106 EmergencyNumber Master number on the camera Add several emergency 106 EmergencyNumber EmergencyNumbe numbers on the camera r Master Delete an emergency 107 EmergencyNumber Master number Delete several 1 e EmergencyNumbe emergency numbers Delete all emergency 107 Master numbers Network Set MMS center 124 MMScenter Master parameter 125 GatewaylPHWAPGatewayPort HTTPGate Set APN parameters Master settings wayPort APN APNusername APNpassword capture Master Capture one image and 03 i images Family send to the user mobile Master 03 pass
50. word Guest Capture more than one Master 03 Image Quantity image and send to the Family user mobile 03 Password ilmageQuantity Guest Capture image s and Master send back to user s 03 mage Quantity 1 Family pre set E mail address Capture image s and Master 30 NumberOrEmail lmage Quantity i send to appointed Family iW50 User Manual Version 1 2 44 www orbien co uk mobile or E mail 30 Password NumberOrEmail I mage Quantity esi ues address Add modify an E mail Master 108 EmailAddress address Family Delete all E mail 109 Master address Enable timing sends E mail settings 115 1 Master MMS images Timed Set time period to 116 WorkDay StartTime 1 EndTime 1 IntervelT Mast aster imaging auto send MMS image ime7 StartTime3 EndTime3 intervelTime3 Disable timing send 115 0 Master MMS image No SMS notification message upon arming Master 137 0 or disarming the camera Family via remote control Send SMS notification Remote i message upon arming Master control f 137 1 or disarming the camera Family via remote control Remove all remote Master controls from the 111 f Family camera Emergency Mode1 to Master 39 0 dial Family Emergency Emergency Mode2 to Master send SMS and MMS 39 1 Family message Activate infrared body Master infrared 118 1 detector default Family body Deactivate infrared body Mas
51. y changing Default 144 1 No SMS notification upon the power supply changing 144 0 Successful SMS reply Not Send SMS notification when power supply changed Chapter 6 Maintenance Store and use the iW50 in suitable temperature Too high or too low temperature will likely to damage the camera Try to keep the iW50 camera and all its accessories dry Do not store and use it in the bathroom or other place with high humidity Do not pour water or other liquids into the camera Do not store and use the camera in dusty areas Do not use alcohol acetone and other similar solvents to clean the camera Wipe it with soft wet cloth Do not attempt to open the camera To prolong the life span of the battery connect the camera to the power supply to charge the built in Lithium battery for 4 hours every 3 months If the camera has not been used for a long time then charge the battery for at least 12 hours to achieve the full performance of the battery iWS50 User Manual Version 1 2 42 www orbien co uk Chapter 7 General troubleshooting No General Trouble Possible Reason Solution Can t start camera Other master is already set in the 1 i Recover to default setting Indicator is working camera Caller ID presentation or MMS f i Contact network provider to All functions disable functions of the SIM card do not i 2 i a n active SIM card function or Indicator is w

GSM Remote Security Camera User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents