Scantronic 9500 User Manual.xls
Contents
1. aes SETTING AND PART SETTING gt a 7 40 00 atus Day M ABNORMAL SETTING Enter user code BE CHIME SETTING CUSTOMER LOG AND TESTING SYSTEM Press Enter Do you want to i isolate circuits Press Do you want to Yes set the system Press Yes Press No Please wait Press Do you want to testing system Yes Part set the system If circuit There is All circuits O K please leave Isolate circuit Alternates between Enable Disable Note 8 Chime Bound Enter 4 digit circuit number to be isolated Violation 27 July 18 40 00 circuit 2051 circuits omitted Note 7 Close displayed Alternates between circuit s Isolate Circuit 2051 Chime Sound Disabled Yes No Continue search for exit fault Press Yes Repeat for other circuits to be isolated 27 Jul 18 40 00 Status Exit Note 6 Press No Press Press Yes No Do you want to isolate circuits Press No Press Yes Chime Sound Enabled Yes No Isolate 27 Jul 18 40 00 Violation EXIT FAULT circuit 2051 circuit 2051 Y N Press Yes Enter user code If a detector is fitted at the control panel or the final exit door is Review known to be open the fault exit faults condition will be cleared when the 27 Jul 18 40 00 Alternates 27 Jul 8 40 00 detector is clear or the final door is Status Exit bet2. iolation Press Yes to Proceed with z Walk test view the rest of E the customer lo 9 Press No Strobe E Press No on to exit from log 27 Jul 18 41 00 Status Day 27 Jul 18 41 00 Status Day 27 Jul 18 41 00 Status Day Press Yes Note 6 The system will set on expiry of the programmed exit time Alternatively the system can be set by operating an exit terminate switch or lock set switch provided these set options have been programmed Note 7 This will only be displayed if circuits have been omitted Note 8 If the final door is open or the door switch is faulty the display will show Final exit circuit instead of Violation circuit NORMAL ENTRY PROCEDURE Enter Premises Via Prescribed Entry Route al Entry Tone Starts 27 Jul 20 34 00 Status Entry Key In Your User Code Press Yes Entry Tone Stops 27 Jul 20 34 00 Status Day Note 1 PROGRAMMED ABORT Should the user accidentally deviate from the prescribed entry route the system will automatically change from the Entry mode to the Abort mode if programmed by the installer The internal sounders will emit a warning tone and the operator has the preset time of 90 seconds to enter a valid access code and return the system to the Day mode Note 2 PROGRAMMED NON ABORT When the entry door is opened the low level entry tone will start If the alarm system has not been u
3. nset within the programmed entry time the tone will change to a high level warning tone for a further 30 seconds before a full alarm is initiated ENTRY AFTER ALARM 27 Jul 20 40 00 Status Alarm Enter User code If programmed for engineer reset EE display will alternate between If programmed for customer reset display will alternate between Alarm 2015 20 42 00 27 Jul 90 Alarm 2015 20 42 00 27 Jul 90 27 Jul 90 20 43 00 CALL ENGINEER 27 Jul 90 20 42 00 RESET REQUIRED Enter User Call engineer You may view code the customer log by entering El user code Press Yes a Display 27 Jul 20 41 20 customer log Status Day Press Yes 20 42 00 27 Jul 90 Alarm 2015 Press No to exit customer log Press Yes to view previous events Note 3 If the system has been programmed to Auto Rearm and an alarm has been initiated prior to entry this will be displayed after entering the user code Follow display instructions Manufactured by Scantronic Ltd Perivale Industrial Park Greenford Middlesex UB6 7RJ Telephone 081 991 1133 Telex 915810 SCANCO G Fax 081 997 4448 LEA Pt No 495618 JAN 91 Issue 1
4. ween circuit omitted Press Yes to check exit closed If fault is not cleared an exit alarm will occur Internal sounder only return to the control panel enter user code and investigate cause faults again or Press No to return to Day state 27 Jul 18 40 00 Status Day 4 Enter user code i Corle k k st 7 Press Enter Do you want to set the system Press No Do you want to Part set the system y Enable Disable Chime Sound Chime Sound Disabled Yes No Chime Sound Enabled Yes No 27 Jul 18 40 00 circuits omitted Note 1 When circuits are isolated only the detector circuit is isolated The tamper circuit will remain armed Note 2 The customer log contains up to 32 events which must comprise events which occurred during one set cycle i e from arming to disarming the system The log will show alarm events only including daytime tampers and 24 hour alarms Note 3 Sounder bell and strobe test cannot be initiated from the remote keypad Note 4 You will be unable to test the P A buttons 24 hour circuits or Technical Alarms Note 5 Only circuits which have been programmed as Omit Allow by the installer can be isolated Press No Note 2 Note 3 BE Note4 Press Display Press Sounder bell Press Do you want No customer log No and strobe test No walk test Press Yes Press Yes Press Yes E E Alarm WALK TEST sounder test 18 40 27 07 90 Tamper panel no v
Download Pdf Manuals
Related Search