INTEGRATED AMPLIFIER USER MANUAL
Contents
1. Standby All the input indicator lights will be extinguished and the MODE indicator light will change to GREEN NOTE First time when you bring the Kandy out of STANDBY after switching it ON at the Mains the input selector will default to CD as described previously Subsequently however bringing the Kandy out of Standby from Standby using the MODE or the POWER Remote handset buttons will restore the selected input and tape values before it was put into Standby INPUT SELECTOR BUTTONS The INPUT Selector Buttons 2 Back and 3 Forward march through the inputs one click at a time They connect each signal source to the amplifier by marching through the Inputs with the exception of TAPE Pressing the Forward Button 3 repeatedly will select inputs in this sequence CD TUNER VIDEO LINE1 LINE2 PHONO CD Pressing the Backward Button 2 repeatedly reverses the sequence Whenever an input is selected the appropriate indicator light will illuminate VOLUME CONTROL The VOLUME Control is a precision device It follows a logarithmic law so that its response approximates that of the human ear There is an indicator on the volume control to show the appropriate volume setting TAPE MONITOR When you select an INPUT the selected source is connected to the amplifier and to the Tape Output Sockets 4 of the Kandy thus enabling you to record from the selected INPUT The Tape Monitor is an override Pressing the TAPE button 12 con2. amp OE Page 3 of 11 ENGLISH INSTALLATION K2 ROKSAN Kandy K2 Integrated Amplifier Front Panel View 4 5 6 7 8 9 10 11 12 3 14 12 13 VOLUME 15 1 Mode Button 9 Line 2 Input Indicator 2 Input Button Back 10 Phono Input Indicator 3 Input Button Forward 11 Tape Monitor Indicator 4 Mode Indicator 12 Tape Monitor Button 5 CD Input Indicator 13 Headphone Socket 3 5mm Jack 6 Tuner Input Indicator 14 Volume Control 7 Video Input Indicator 15 AC Mains Power Switch 8 Line 1 Input Indicator ROKSAN Kandy K2 Integrated Amplifier Rear Panel View 1 2 3 4 5 6 7 8 9 10 IMPORTANT POWER AMP OUTPUT CAUTION R CONTINUED A A eg BS b gt PROTECTION Acar RISK OF D o D Tyee Hise CF z NOTE INS SWITCH AVIS WARNING LOCATED ON THE FRONT RISQUE DE CHOC UNDERSIDE OF THE UNIT SHOCK HAZARD ELECTRIQUE Ne PASOUVRIR PONOT OPEN MADE IN ENGLAND 17 16 11 12 13 14 15 1 Pre amp Output 1 Multi Amping or Subwoofer 10 CD Input 2 Bypass Input When Bypass switch is set to ON 11 Right Speaker Output 3 Tape Input Playback 12 Left Speaker Output 4 Tape Output Record 13 AC Mains Input 5 Phono Input Moving Magnet 14 AC Mains Fuseholder 6 Line 2 Input 15 Voltage amp Fuse Label 7 Line 1 Input 16 Phono Input Chassis Grounding Terminal 8 Video Input When Bypass switch is set to OFF 17 Bypass Switch Selects between Video amp 9 Tuner Input Bypass Inputs Roksan Audio Itd CLASSIFICATION General Use Version 3 5 A
3. mains socket which plugs into the IEC connector on the unit s rear panel The other end is normally attached to the appropriate mains plug for your country In the UK this is the standard UK13A plug This plug should ordinarily not be removed from the lead If you do remove it please dispose of it safely so that it cannot be plugged into a mains socket whilst in a potentially dangerous condition We suggest that you obtain from your dealer a complete replacement lead Should you move to another area where either the mains voltage or the mains plugs are different from those as supplied with your Integrated Amplifier please contact the appointed ROKSAN distributor for assistance Please observe correct mains polarity at all times The Integrated Amplifier mains fuse is located on the rear panel next to the IEC mains connector This must only be replaced by the fuse of the type and rating as described on the fuse rating label on the rear panel of the unit This product requires connection to earth ground The earth wire in the UK this is colour coded green yellow of the mains cable supplied with your Integrated Amplifier must be connected to a suitable earthing point established for this purpose by your electricity supply company If you are in any doubt consult a qualified electrician If the equipment is likely to be unattended for some time unplug it from the mains supply GENERAL CAUTIONS FCC WARNING This equipment may generate or u
4. 20V 50Hz 60Hz 220V 240V 50Hz 60Hz Power Consumption Standby lt 25W Full Power 2 CH 8Q lt 330 W 49 lt 550W Dimension 432 x 380 x 90 W x D x H mm 432 x 380 x 102 including feet Weigth 14 Kg Roksan Audio Itd CLASSIFICATION General Use Version 3 5 All specifications are liable to change without notice E amp OE Page 10 of 11 ENGLISH NOTES K2 Kandy Integrated Amplifier K2 Serial Number Purchase Date Year Month Day ROKSAN Retailer Name Location Please keep a record for future reference www roksan co euk Roksan Audio Itd CLASSIFICATION General Use Version 3 5 All specifications are liable to change without notice E amp OE Page 11 of 11 ENGLISH
5. ROKSAN USER MANUAL Eo gt ROK Say zee ROKSAN AUDIO LIMITED 6 NORTHFIELD INDUSTRIAL ESTATE BERESFORD AVENUE ALPERTON MIDDLESEX HAO INW ENGLAND TEL 44 0 20 8900 6801 6802 FAX 44 0 20 89000734 www roksan co uk Email info roksan co uk PRINTED IN ENGLAND INTRODUCTION K2 Congratulations on your purchase of the ROKSAN Kandy K2 Integrated Amplifier This Integrated Amplifier is designed and manufactured to the highest specification and rigorously tested to reward you with many years of listening pleasure Your Kandy K2 Integrated Amplifier is at the heart of your hi fi system Its correct installation set up and operation will have a profound influence on the sonic performance of the entire hi fi installation Please read the contents of this manual thoroughly It will help you to understand your hi fi equipment better and enhance your listening pleasure This manual is divided into the following sections Safety Instructions Accompanying card Introduction Cautions Installation Setup Operation Troubleshooting Guarantee Specifications Notes UNPACKING Included in the packing of your Kandy K2 Integrated Amplifier you will find e One mains lead fitted with the correct mains power plug for your country e One Roksan Programmable Learning Remote Handset RMX 108 and AAA batteries x4 e One information pack and warranty card After removing these items please retain all packing materials Correc
6. ed and enclosed in an overall plastic sheath Carefully remove any overall sheath or split the figure 8 cable to a depth of about 75mm 3 Carefully strip the insulation on each wire to a depth of about 12mm 1 2 exposing the bare core If the conductor is stranded twist the strands together on each conductor Unscrew the binding post There is a cross hole about 5mm from the panel end of the binding post Insert the bared conductor through the hole and tighten the binding post securely making sure that there are no loose strands or bare ends protruding through the post Carefully observe polarity ensuring that the RED speaker terminal is connected to the RED amplifier terminal and the BLACK speaker terminal to the BLACK amplifier terminal When both left and right channels are connected to their respective speakers the amplifier is ready for use IMPORTANT NOTE For optimum performance it is recommended to use high quality cables such as ROKSAN HDC 02S High Definition Loudspeaker Cable Many speaker cables such as the ROKSAN HDC 02S are directional Please observe this characteristic DO NOT use a speaker cable with conductor size less than 16 AWG 1 6mm Diameter The Binding posts accept conductor sizes up to 12 AWG Roksan Audio Itd CLASSIFICATION General Use Version 3 5 All specifications are liable to change without notice E amp OE Page 5 of 11 ENGLISH Multi Amping The Loudspeakers Setup If the Loudspeaker
7. ll automatically turn off the LCD to save battery life The handset is equipped with a motion sensor and thus will wake up as soon as it is picked up oo no The Back Light will only come on when the back light button is pressed and will stay on during operation Back light will turn off automatically after 10 seconds if none of the buttons are pressed 1 The KANDY AMP CD Button 1 selects Kandy Integrated and CD devices Kandy logo on LCD 2 The POWER Button 2 puts the amplifier in and out of Standby MODE light GREEN and RED 3 The TAPE Button 3 connects the Tape Deck In and Out 4 The MODE Button 4 mutes and un mutes the output level by 20dB MODE light AMBER and RED 5 6 The VOLUME Buttons 5 amp 6 adjust the output volume level Increase amp Decrease 7 8 The INPUT Buttons 7 amp 8 march through the input sources Forward amp Back 9 The BACK LIGHT Button 9 turns on the handset buttons and the LCD display illumination Roksan Audio Itd CLASSIFICATION General Use Version 3 5 All specifications are liable to change without notice E amp OE Page 8 of 11 ENGLISH KNOW YOUR KANDY e When you first power up from the Mains Switch from the front underside of the amplifier the amplifier goes into Standby and the MODE Indicator glows GREEN e In order to reduce power consumption and heat the power stage of the amplifier is shut down when in Standby mode e In normal operation whe
8. ll specifications are liable to change without notice E amp OE Page 4 of 11 ENGLISH SETUP K2 CONNECTING MAINS POWER Please refer to the front amp rear panel view on Page 4 The moulded IEC connector of the supplied mains lead should be plugged into the socket 13 on the rear of the unit first and then plugged into the mains supply The Mains power switch 15 is on the front underside of the Integrated Amplifier This switch can be left on if however the amplifier is likely to be unattended for a long period switch it off and unplug the mains lead from the wall SIGNAL CONNECTIONS Signal Input connections There are 6 Inputs 5 10 on your Kandy Integrated Amplifier in addition to the Tape Input 3 Except for the PHONO input 5 all other inputs are line level and will accept virtually all currently available source components The PHONO input is factory set for Moving Magnet Cartridges to accommodate record players fitted with MM phono cartridges The VIDEO input 8 is linked to the BYPASS input 2 and Switch 17 When the Bypass Switch is set to VIDEO then the VIDEO input will function as a line level input When the switch is set to BYPASS then the VIDEO input will be deactivated and the BYPASS input will become activated In this mode the BYPASS input can be used for connection to a suround sound processor s front L amp R pre output for home theatre use The BYPASS input is directly connected to the power amp section and b
9. n an external fault such as a short circuit on the loudspeaker leads is detected the amplifier will go into standby and the speaker output and AC power relays will disconnect and the MODE indicator light will gow GREEN Unless the fault is rectified the amplifier can not be brought out of standby e If the amplifier output Current exceeds its safe operating range very low loudspeaker impedance and or very high volume level the protective circuitry of the Kandy will take the amp into Standby mode If subsequently the volume is lowered or the loudspeakers changed the amplifier can be brought out of Standby to resume normal operation TROUBLESHOOTING K2 If you suspect that your ROKSAN Kandy Integrated Amplifier is not operating properly you should check all the connections carefully Pay particular attention to speaker phasing and channel connections Phono plugs should be fully inserted a frequent cause of problems is that Phono plug surrounds do not make proper contact Below are some commonly encountered problems with suggestions for possible cure The list is not exhaustive If you have any unresolved problems please consult ROKSAN or your appointed ROKSAN dealer or distributor SYMPTOM LIKELY CAUSE SUGGESTED REMEDY No power AC Mains lead not inserted properly Unit not switched on Ensure AC Mains lead is fully inserted Switch unit on on the front underside No output on one or both channels Very low sound
10. nects the output of your tape deck to the Kandy overriding the selected input However the selected input is left connected to the recording input of your tape deck If you have a suitable tape deck this facility enables you to record a programme whilst monitoring its playback When the TAPE button is depressed the TAPE Indicator light 11 glows and the selected source Indicator remains illuminated The input selector remains functional when the Tape Monitor is ON thus allowing a range of sources to be recorded Pressing the TAPE button toggles between Tape Monitor ON and OFF Roksan Audio Itd CLASSIFICATION General Use Version 3 5 All specifications are liable to change without notice E amp OE Page 7 of 11 ENGLISH REMOTE HANDSET The Kandy K2 Integrated Amplifier is supplied with Roksan s programmable learning remote handset RMX 108 and four AAA size 1 5V batteries Carefully remove the battery compartment cover and insert the supplied batteries in place observing polarity Replace the cover The handset is now ready for use The front panel controls of the Kandy Integrated Amplifier are replicated on the remote handset KANDY AMP CD POWER TAPE MODE VOLUME VOLUME INPUT FORWARD INPUT BACK BACK LIGHT Kandy logo 1 2 3 4 5 6 7 8 9 NOTE The LCD display amp the hand set will turn on as soon as the batteries are inserted If the handset is left untouched for 90 seconds it wi
11. output Poor speaker imaging lack of Bass output Amplifier in stand by mode MODE light GREEN Missing or bad input signal connection Incorrect speaker connection Wrong input selected Tape Monitor selected Amplifier set in 20dB MUTE position MODE light AMBER Loudspeakers connected out of phase Press MODE button to set amplifier in operational mode MODE light RED Check all input connections Check speaker output connections on rear panel Select correct input ascertain source is working Deselect Tape Monitor Press MODE button to set amplifier in operational mode MODE light RED Check volume setting first Check polarity of speaker connections especially important if Multi wiring Multi Amping Hum from speakers Incorrect grounding Check Mains polarity and grounding on all connected equipment Roksan Audio Itd CLASSIFICATION General Use All specifications are liable to change without notice E amp OE Page 9 of 11 Version 3 5 ENGLISH GUARANTEE K2 There are no user serviceable parts inside your Kandy Integrated Amplifier If a fault should develop refer all servicing to your appointed ROKSAN retailer distributor or ROKSAN approved service agent Your ROKSAN Kandy Integrated Amplifier is guaranteed against any defect in materials and workmanship for a period of two years from the date of purchase This guarantee only becomes effective if the warranty card is valida
12. r 4 illuminated in GREEN The amplifier is now ready for use Roksan Audio Itd CLASSIFICATION General Use Version 3 5 All specifications are liable to change without notice E amp OE Page 6 of 11 ENGLISH You can activate your Kandy Integrated Amplifier in two ways 1 Press the MODE button 1 on the front panel once 2 Press the POWER button 2 on the remote handset once The Kandy Integrated will wake up the MODE indicator illumination will change to RED the CD input will be selected and the CD input indicator 5 will illuminate RED The amplifier will then automatically check its input output status and after a brief moment when no problems are detected the speaker output relays will click on and the amplifier starts in normal operation mode responding to all front panel buttons and the remote USING THE CONTROLS MODE CONTROL The MODE button on the Front Panel 1 has the following functions e It activates the amplifier from Standby NOTE From the Remote Handset only the POWER Button 2 can put the amplifier in and out of standby e Pressing the MODE button once with the amplifier activated will mute lower the volume level by 20dB The MODE indicator light will change to AMBER The amplifier remains fully functional in this mode Another single press un mutes the amplifier and the MODE indicator light will revert to RED e When the amplifier is activated a sustained press on the MODE button will put the amplifier into
13. s utilise more than one drive unit with individual input terminals for example a Tweeter and a Woofer then the loudspeaker performance should benefit from Bi Amping Dedicating one amplifier to the Tweeter and another to the Woofer isolates them from each other hence reducing distortion and increasing reserved power Speakers work far better with most amplifiers when Multi Amped than using one yet more powerful amplifier For setup and connection details on Multi Amping refer to the Kandy Power Amplifier Manual Note Multi Wiring connects the Woofer and the Tweeter terminals directly to the output terminals of the amplifier and is the first step towards Multi Amping MULTI WIRING THE LOUDSPEAKERS Tri wired Speaker Bi wired Speaker IMPORTANT Speaker Drive Unit E Links must be removed el KANDY INTEGRATED AMPLIFIER MADE IN ENGLAND OPERATION K2 Please refer to the front and front amp rear panel views on page 4 and the Remote Handset View on page 8 SWITCHING ON The Mains power switch 15 is located on the front underside of the amplifier This switch can be left ON for normal operation If unattended for a long period Going on a short break holidays etc the Mains power should be switched OFF and the power cord disconnected from the mains power input When switched ON the K2 logo in the mirror display will glow red and your Kandy Integrated Amplifier will be in STANDBY with the MODE indicato
14. se Radio Frequency energy The user may lose the right to operate this equipment if unauthorised modifications are made INTERFERENCE Properly installed this unit should not cause harmful interference to radio communications There is however no guarantee that such interference will not occur in a specific installation If interference arises which you can determine by switching the unit off and on you could try to remedy matters by the following e Re orient or re locate the receiving antenna e Increase the distance between the Kandy Integrated Amplifier and receiver e Connect the unit to a different mains circuit from that of the receiver e Consult your ROKSAN appointed dealer or an experienced Radio TV technician for help and advice LOCATION Your Kandy K2 Integrated Amplifier should be located in a well ventilated area and kept away from sources of heat dust and humidity and from direct sunlight The Integrated Amplifier may be positioned either as a free standing unit or alongside another audio video product Never place the Integrated Amplifier on carpet or any surface likely to hinder normal ventilation Never allow liquids or other objects to fall into the unit This unit contains no user serviceable parts Do Not remove any panels or attempt to service it yourself Unauthorised servicing will void the warranty Roksan Audio Itd CLASSIFICATION General Use Version 3 5 All specifications are liable to change without notice E
15. t packing is necessary for future transportation of your Kandy K2 Integrated Amplifier MAINTENANCE After disconnecting the Kandy K2 Integrated Amplifier from the mains supply the cabinet and front panel may be cleaned with a lightly dampened soft cloth or chamois leather Avoid using abrasives or solvents EU DIRECTIVES This product is designed to comply with the legal provisions of EU Directives 89 3336 EC and 72 23 EC The standards which have been applied are those which were in force at the time of the introduction of this product This product is compliant to EN 60065 This product must be earthed Please ensure that other equipment connected to it is earthed according to the manufacturer s instructions This product bears the CE mark Roksan Audio Itd CLASSIFICATION General Use Version 3 5 All specifications are liable to change without notice E amp OE Page 2 of 11 ENGLISH CAUTIONS K2 AC MAINS SUPPLY Your Kandy K2 Integrated Amplifier is set to operate from a fixed supply voltage which is marked on a label next to the mains input plug Before connecting the mains lead please check that your mains supply corresponds to this label as below 230V ProductS sosaren iarere eee eset en ee ees Voltage Range 220V 240V TISV Products 4 2 icsheeliesees ieee rice AAEE Voltage Range 110V 120V TOOY ProductS oisein repet nenia eset ee ee teenies Voltage Range 90V 110V The mains lead supplied with this product has an IEC
16. ted by the ROKSAN retailer from whom the equipment was purchased and returned to ROKSAN within 28 days of purchase This guarantee excludes 1 Damage caused due to accident missuse neglect and incorrect installation adjustment or repair 2 Liability for damage or loss during transit from the retailer or purchaser to ROKSAN or its authorised distributor for the purposes of repair or inspection Carriage costs to ROKSAN shall be borne by the consignor All claims under this guarantee must be made through an authorised ROKSAN retailer If equipment returned for repair to ROKSAN is found on inspection to comply with the product specification ROKSAN reserves the right to make a charge for examination and return carriage Unauthorised servicing will void this guarantee SPECIFICATIONS K2 Inputs Line Level x5 Moving Magnet x1 Tape x1 Bypass x1 Input Impedance 47 KQ Input Sensitivity 120W Line 470mV Outputs Speaker L amp R x1 Preamplifier x1 Tape x1 Headphone x1 Output Power gt 125 Watts into 8Q both channels driven gt 190 Watts into 40 both channels driven Power Supply 500VA Ultra Low Noise Toroidal Transformer 4 Regulated Supply Rails Damping Factor gt 110 8Q Frequency response 3dB lt 3Hz gt 100kHz Gain 37 3dB Overall Pre amp Power 5 7dB Preamplifier 31 6dB Power Amplifier Harmonic Distortion lt 0 005 1kHz 8Q Signal to Noise Ratio Line 100dBa ref 470mV Power Source 100V 1
17. ypasses the preamp The volume is then controlled via the surround sound processor and not the Kandy integrated You could also use the integrated as a power amp in this mode All the inputs use Gold plated RCA Phono Connectors and should be connected according to the standard convention Right Channel Red Left Channel Black or White Also in accordance with standard practice the Upper row of Phono Sockets carries the Left Channel and the Lower row carries the Right Channel The Input Sockets are labeled with their legends upside down as well as the normal way up to assist you should you be connecting an input from a position in front of and above the amplifier MC Input Connections If you wish to use a Moving Coil cartridge an in line MC step up transformer should be connected to the Phono Input Alternatively a dedicated Phono Stage can be connected to a Line level Input NOTE If you wish to connect to the Phono Input it must be set for Line level signal See above For advice and demonstration of ROKSAN state of the art turntable reproduction systems contact your authorised retailer LOUDSPEAKER CONNECTIONS The right and left loudspeakers are connected to the amplifier via the rear panel binding posts 11 and 12 respectively There are two basic types of cable e Figure 8 cable has two insulated conductors which lie parallel either side by side or spaced by insulation e Overall sheathed cable has both conductors insulat
Download Pdf Manuals
Related Search