TemPoint User Manual
Contents
1. nnenennennnennennennnnnnonnennenneennennenneonnannennenneannennenneannennenteansennennennn enne 13 ks elda a RO i a 13 A Maale mmm eee ee mer eee ne eee ee eee ios dise 13 A a E I mm a iu ere 13 ee A e e PO GE UU O m TA 14 E CO OO E CO US OP OU O OE 14 A CS In e PP E CP Un II A 14 PP e A Pr 15 Ce eT E A e Un e A ROS OP UE o wactsencseinn 15 9 Step by Step Guidance n nnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn mnn mnn nnnnnnnnnnnnna 16 9 1 Weekly Test Recommendations vnnrennrnnnnanananana navn nnnnnn ranna nan n nan n ranna nan ann nan nnnna 16 9 3 Enabling Disabling Devices nmennennennnennenneennennennenneannennenneannennenneannennenneaneneennennenneenne neeme 17 9 4 Enabling Disabling Zones nmeennennennnennennenennnennenneannennennennnennonnennseneennennsennenneaneeneennenne enne 18 9 5 Enabling Disabling Brigade Relay oooncccccccccnncnncccconncnncccnonncnnnononononnnnonnnnnnnnnnnnnnnnnnnnnnnnnnnnononnnnnnnnnonanes 19 A AA e 19 9 7 Viewing the Event Log nnrenenennenennanenennennenennaneneenennenenneneneenen nene nnenennennnnenennenennen neeme 20 9 8 Enabling Disabling Networked Devices vsrrnsneeneenennenneeennnnenene ne nnnnnnen enn nnnnnna annan 21 9 9 Selecting Verify Delay Operation veerenneennenenneaneennnnnnnn nan nnnnnna ann nnnnnna nan ennnna annan 22 10 ROULING Tes2. 02 07 13 Illuminates whilst a device or detection zone is in TEST MODE Illuminates should a Sounder Based Device indicates a fault condition 6 TemPoint 6 Control Keyswitch The Control Keyswitch has three different positions They are OFF ON and ISOLATED Each of their functions are explained on the following page 6 1 OFF Normal Position Functionality Access Level 1 With the control keyswitch in the OFF position the panel is at Access Level 1 The key is ISOLATED removable in this position and it is recommended OFF ON that the panel is left in this position with the key removed The following control options are available OFF position Operational when multiple events are displayed to enable each event to be viewed Operates Status lamp test when system has no events shown 2 Feature Displays any device zone currently in test of key This will automatically timeout and return to the Front Screen if left in this mode View 2 Feature Displays any device zone currently disabled Disablements Of key This will automatically timeout and return to the front screen if left in this mode 2 Feature Displays any device currently in fault of key condition This will automatically timeout and return to the front screen if left in this mode 2 Feature Returns to view fire events if any of the other of key view options used This will automatically timeout a
3. EMT TlemPoInt EAK TA a e By n B ms B EN 5 g Bs ei TE z a m2 rn gt TONE FALAT ARE OMSARED SOUNDER FAULT AUS AN l EARTH FALLT i a 0 ee 4 5 SILENCE ALARM AR N RESET LED TEST gt L ISOLATED W A na AD E i DISASLEMENTS FARTS ro pr a USER MANUAL TemPoint Table of Contents Section Page No 1 INTOCUCHON arras 4 LLP OCCU orare EEEE EEEE ETER 4 1 2 Warnings and Cautions MAMM N AEE m m m t cs 4 2 User Control Level Sunat 4 3 User PasSWo ordsi iia 5 4 Controls and DisplayS iia 5 Ed Controls La vou rarr EE EEEE ENC 5 5 Table of the Functions of the panel s LED Indicators nnnnnnnnnnnnnnns 6 6 Control KeySWIECH strain iia 7 6 1 OFF Normal Position Functionality Access Level 1 0occccccccconccnncnrn nr 7 6 2 ON Position Functionality Access Level 2 ooccccccocnncccccccocccnncccoonnonnnoconnnononononnnnnnnnnnnnnnnnnnnnnnnnnnnonenanens 8 6 3 ISOLATED Position Functionality cccccconccnccccccnncnnncccnoncnnnnnnonnnnnnnononnnnnnnnnnnnnnnnnnnnnnnnnnnnannnnnnnnnnnnnnnnnnonanes 9 Z User Option FUNCUONS sii 10 8 Alphanumeric Display Indicators nnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnna 12 y arian A A EE eceesne nen veceiadecacesvarnaecmnae tenner tacmauanseusientt 12 lp AP UP e E o OOO A 12 8 2 Fire Networked Device
4. Check the operation of the audible alarms and any link to a remote manned centre central station etc v Carryout a visual inspection of the system to check for alterations or obstructions vi Issue a Certificate of Testing 10 4 Annually The responsible person should ensure that in addition to the guarterly checks each device on the system is tested and that a visual inspection is made of the cable fittings and eguipment 10 5 Periodic Cleaning The Control Panel and devices should be periodically cleaned by wiping with a soft damp cloth However the use of solvents on the Control Panel or Devices is not recommended TEMPOINT USER MANUAL ISSUE 1 02 07 13 23 TemPoint 11 Logbook One or more individuals should be appointed to maintain a Logbook and to oversee all entries and record all events resulting from or affecting the system The Logbook should be kept in a safe place closely situated to the Control Panel It should only be accessible to those authorised persons The names of the responsible appointed persons should be recorded on the Reference Data Table below All events including real and false Fire Events Faults Pre Alarm Warnings Tests temporary Disablements should be properly recorded Service visits should also be recorded Such recordings should be accompanied with brief notes of any work that has been or is to be carried out Such Reference Data should be detailed in the sample below Ref
5. intended for use by the System Installer Maintenance Contractor TEMPOINT USER MANUAL ISSUE 1 02 07 13 4 TemPoint 3 User Passwords It is possible for the system to be programmed to allow a PIN number rather than the control keyswitch to change from Access Level 1 to Level 2 The system is not programmed as standard with this feature as the control keyswitch is normally used however up to 99 User PINS can be assigned changed at User Level 3 by the Installer Maintenance Contractor if required 4 Controls and Displays 4 1 Controls Layout The TemPoint control panel provides status information via the Display Zone Lamps and Status Lamps The display and control of the panel s functions is achieved through two control panel sections Figure 1 shows the display area which includes Fire Zone Lamps the Display itself and the A and V Scroll Buttons Zone Lamps Scroll Buttons Front Panel Lock 2 i 4 T OHHH HE se be HL 59 TaT 334 HEI a oe 080096 de gt 5d bs Ad he ae g 99 a E oo e 20 Character 4 Line Display Figure 1 Zone Lamps and Display 96 Zone model shown The TemPoint Panel is controlled by the use of the Control Keyswitch a Numeric Keypad and 3 Control Buttons Fig 2 shows the Panel Controls and Indicator Lamps EARTH FAULT IRE x E e E ie GENERAL FAULT TEST MODE SYSTEM FAULT BLE ARE BRI
6. GADE SOUNDER 8 DETECTOR ZONE Status FAULT OUTPUTS DISABLED DISABLED E E Lamps RESET SILENCE SOUND LED TEST ALARM ALAR MS Ls Control Buttons Control Keyswitch Figure 2 NOTE The Status Lamps Buttons Control Keyswitch Buttons operation is identical for all styles of control panel TEMPOINT USER MANUAL ISSUE 1 02 07 13 5 TemPointE 5 Table of the Functions of the panel s LED Indicators LED Indicator Led Colour s Control Panel Function Indicates a good AC power supply ZONE FAULT GENERAL FAULT ARE BRIGADE FAULT Illuminates should one of the detection devices develop a fault condition Illuminates should a fault condition occur within a Control Panel or device Illuminates should a communication fault occur between the Alarm Routing eguipment and the Control Panel Illuminates should an earth fault condition occur on the system ARE BRIGADE Illuminates when communication with DISABLED the Alarm Routing Eguipment is disabled EARTH FAULT TEST MODE SOUNDER 8 OUTPUTS DISABLED Illuminates when an individual Sounder Output device or sounder zone is disabled Illuminates when any device is in Fire Alarm condition along with the fire zonal LED SOUNDER FAULT SYSTEM FAULT DETECTOR ZONE DISABLED Illuminates should a fault become present with the control panel itself Illuminates when a Detection Device or Zone is disabled Fig 3 TEMPOINT USER MANUAL ISSUE 1
7. System Menus N A Options and further Fire system Options Menus are now accessible by pressing the 0 Key Details are shown in Section 7 Isolated Lamp ISOLATED Sounder group disabled by key position This is a programmable feature normally o used for isolating plant equipment on a weekly test and is configured by the Installer Maintenance contractor TEMPOINT USER MANUAL ISSUE 1 02 07 13 9 TemPoint 7 User Option Functions The following Level 2 functions are available Put the Control Keyswitch into the ON Position amp Press the 07 Key Options Passwords Press the Time and Date YES key Logging Fire System Opts Fire System Dev Disable Test Net Disable Test Det Zone Note If events are Dis Test displayed on the System Pressing the 0 Key with Alarm Zone the Control Keyswitch in Disable the ON Position will ARE Disable take system direct to the System Mode Fire System Menu Engineers Config Printer Options Access Level 3 via PIN entry To scroll through the menus use the A and V scroll buttons To enter a menu position the reguired option between the gt and lt cursors on the screen and press the YES key TEMPOINT USER MANUAL ISSUE 1 02 07 13 10 TemPoint A Options FUNCTION DESCRIPTION Passwords Contains 7 sub menus This allows the option to change edit and delete PIN numbers if used Enables you to view the entire log
8. T USER MANUAL ISSUE 1 02 07 13 99 TemPointE 10 Routine Tests In order to ensure that the system is fully operational the following routine tests to the system should be carried out Note Records should be maintained of all testing activities on the enclosed Logbook Data Table 10 1 Daily Check the control panel to ensure that it indicates normal operation Status should be Normal If any fault is indicated check that it has been recorded in the logbook event data table and that the appropriate actions have been taken E g informing the maintenance company 10 2 Weekly Test at least one detector or call point to confirm the operation of the panel and the audible alarms A different zone should be tested each week and if possible a different device Record the outcomes of the testing The zone and the device number should be noted into the Control Panel logbook Any malfunctions must be reported The LED TEST key should be pressed to ensure that all of the LED Indicators are in full working order 10 3 Quarterly The person nominated with the responsibility for the system should ensure that a competent person checks the system every 3 months The competent person shall i Check the Logbook Event Data Table entries and the results of any action taken ii Check the standby batteries and the charger voltage iii Test at least one device in each zone to verify the functionality of the Control Panel iv
9. e YES key and you will enter the Date Time Menu To set the time press the YES key again and enter the time in 24hr hh mm format Then press the YES key to confirm Press the NO key twice to return to the main display To enter the date from the Date Time Menu press the V button twice until highlighting gt Set the Date lt then press the YES key Now enter the date in dd mm yy format and then press the YES key to confirm Once confirmed press the NO key twice to return to the main display NOTE On Multi panel systems it is only necessary to alter the time and date on the Master Panel and this will automatically pass the information to other panel s on the system 9 3 Enabling Disabling Devices To Enable Disable a device from the main screen With the control key switch in the ON Position press the 0 key then scroll down to last option Fire System Options Press the YES key Now whilst highlighting the gt Dev Disable Test lt option press the YES key again Now press the O key and enter the desired device number and press the YES key The display will show TEMPOINT USER MANUAL ISSUE 1 02 07 13 17 TemPomt Note If an event is displayed the Fire System Menu is immediately accessed by turning the Key into the ON Position and pressing the O Key Then press the V butto
10. e screen will now display NOTE It is important the correct Panel type is highlighted PAN Hardwired Panels NET Radio Network Panels This information can be provided by installer Maintenance Contractor if required Press YES key once to change the Panel type to the required setting Press the V key one time and the screen will now be highlighting gt Panel 00 lt Press the YES key to change the panel number until the desired panel number is shown Press V key one time and the screen will change to highlight gt Device 00 lt Press 0 key and the screen will now display Enter the device number that you want to Enable Disable e g 007 then press YES key and screen will now display Press the V key one time and the screen will change to highlight gt Status Active lt Press YES key once to change the Status of the device to Active or Disabled as desired Now press the V key once and whilst highlighting gt Transmit Event lt press the YES key to transmit the event The screen will state that the change has been made Press NO key four times until the screen returns to the main display Turn the control keyswitch to the OFF Position and the screen will now indicate that the Status is Normal TEMPOINT USER MANUAL ISSUE 1 02 07 13 gt TemPointE 9 9 Selecting Verify Delay Operation Delay Mode Operation The panel can be configured to op
11. erate in a delayed mode either manually or via a secondary keyswitch When selected alarm signals received from a detector will generate a fire alarm message on the panel but delay the operation of the sounders The panel will initiate a full fire alarm condition if no action is taken on this warning within a specified period The use of visual delay mode must be configured at level 3 by an installer maintenance contractor before it is available for use at level 2 The visual delay mode can be configured to operate when manually selected at the panel via a secondary keyswitch or automatically via a separate timer The maximum time allowed for acknowledging the timer can be programmed in intervals of one second Whilst the visual delay mode Function is active the front screen will display VERIFY DELAY MODE Standard Delay Operation When a fire alarm condition is detected in this mode the internal buzzer will sound The device location will be shown on the display along with a warning that the panel has entered delayed alarm If the warning is not acknowledged by pressing the SILENCE ALARM button within the time allowed then a full fire alarm condition will be raised and the sounders will activate Pressing the SILENCE ALARM button within the time allowed will cause the timer to stop A secondary device activating within the timer or a manual call point activation will immediately generate a fire alarm condition TEMPOIN
12. erence Data Table Site Name and Address Site Telephone No Responsible Person s System Installer This System is Maintained by Until Maintenance Companies Contact Telephone No On the next page is a sample page of the Logbook This can be photocopied to produce a suitable Logbook TEMPOINT USER MANUAL ISSUE 1 02 07 13 94 TemPointE No Zone No Completed TEMPOINT USER MANUAL ISSUE 1 02 07 13 25 TemPomt EMS Group Head Office y Technology House i kd Sea Street i Herne Ba a ES a Fire Fire Industry Association Association tal JAKA Hy ea Kent CT6 812 United Kingdom gt EAN 444105 gay AASA FOLLOW US ON ISO 9001 a Ewitter YY iso 1SO 14001 Radio Fire amp Security enquiries emsgroup co uk systems Limited www emsgroup ca uk emstechnical Approved Company ucts as part of its The information contained within this literature is correct at time of publishing The EMS Group reserves the nght tocchange any Infomation regarding products continual development enhancing new technology and reliability The EMS Group advises that any product literature issue numbers are checked with its head office prior to any formal specification being written TEMPOINT USER MANUAL ISSUE 1 02 07 13 28
13. ing the Event Log Turn the control key switch to the ON position and press 0 key The screen will now display Press the V key twice until the screen displays gt Logging lt Press the YES key and the screen will change to highlight gt View Log At Date lt Now press the YES key and the screen will now display Enter the required date to view in dd mm yy Format e g 28 05 03 then press the Yes key and the screen will now display By pressing the A and V scroll buttons the log for the date selected can be viewed All fire and fault events are listed in date and time order Pressing the 5 key will take you to the oldest event whilst pressing the 8 key will take you to the most recent event When finished press the NO key three times until the screen returns to the main display Turn the control key switch to the off Position and the screen will now indicate that the Status is Normal TEMPOINT USER MANUAL ISSUE 1 02 07 13 20 TemPomt 9 8 Enabling Disabling Networked Devices Turn the control key switch to the ON position Press 0 key to enter the Options Menu Press the V key three times until the screen displays gt Fire System Opts lt Press the YES key and the screen will change to highlight gt Dev Disable Test lt Press V key once to highlight the option gt Net Disable Test lt and press the YES key and th
14. kept in a safe place near the system only with access by authorised personnel A sample logbook sheet is displayed in Section 11 1 2 Warnings and Cautions These instructions contain the procedures to follow in order to operate the TemPoint control panel correctly It is assumed that the user has been suitably trained and is familiar with the relevant regulations All equipment is to be operated in accordance with the appropriate standards applicable The material and instructions covered in this manual have been carefully checked for accuracy and are presumed to be correct However the manufacturer assumes no responsibility for inaccuracies and reserves the right to modify and revise this document without notice 2 User Control Levels TemPoint has three different access levels They are Levels 1 2 amp 3 At User Level 1 all of the displays are completely functional however the panel s control buttons and menu access features are inhibited At User Level 2 Standard user access level via control keyswitch all panel controls are functional and the control panel s menu is accessible The requirement of the Engineers PIN at the Engineers Config Menu allows access to Level 3 At User Level 3 all the panel s controls are functional and the control panel s menu is fully accessible making full system configuration possible User Level 3 is reached by entering the Engineers PIN from Level 2 Engineers Config Menu User Level 3 is
15. l Panel has activated a Fire Alarm the following alarm screen will be shown The above display shows that a Fire Alarm has been generated from Device 27 in Zone 1 on Panel 4 8 25 Pre Alarm When a Pre Alarm event occurs the text on the display changes to show The above display shows that Device 27 has entered a Pre Alarm event in Zone 3 8 3 Tamper When a device generates a Tamper Alarm the display will change to show The above shows that Device 5 has generated a Tamper Alarm in Zone 1 8 35 Fault Event When a Fault Event occurs the text on the display changes to show The above display tells us that device 56 has entered a Fault condition in Zone 4 TEMPOINT USER MANUAL ISSUE 1 02 07 13 3 TemPomt 8 4 Fault MN In the instance of a system mains failure the controller will switch into battery safe mode This will turn the display completely off and the Power LED will extinguish Pressing any key on the panel will re activate the display and the following fault screen will be shown FAULT MN represents the controller has had a mains failure The CIE Fault LED will also illuminate when the above screen is displayed 8 45 Fault BT This fault can be displayed for a number of reasons There maybe no batteries present in the unit Secondly the batteries may not be charging Thirdly the battery voltage may be low The battery not charging and low voltage readings would be dis
16. lay turn the control key switch to the ON Position and Press the 0 key Scroll down to the bottom of the Options Menu using the v button until highlighting gt Fire System Options lt Press the YES key Press the v button until highlighting the gt ARE Disable lt option Press the YES key Then press the YES key again to change from ENABLED TO DISABLED alternately Then having selected the desired option press the NO key three times to return to the main display 9 6 Printer Options To enter the Printer options from the main display put the control key switch into the ON position Press the 0 key Now using the V button scroll down to the last option gt Fire System Options lt Now press the YES key Then scroll down pressing the V button to the last option gt Print Options lt Now press the YES key Now having reached the Print Options press the YES key to turn the Printer ON or OFF Whilst the printer is set to ON press the V button then press the YES key to change the print event between FIRE or ALL This depends on whether the printer is required to print All events or just any Fire Events Once suitably configured press the NO key three times to return to the main display TEMPOINT USER MANUAL ISSUE 1 02 07 13 19 TemPomt 9 7 View
17. m is connected to an alarm receiving centre they should be informed before and after the test and the fire alarm signal confirmed Carrying Out the Test If applicable contact the alarm receiving centre to inform them that a Ey test is about to be carried out Turn the key on the control panel to the ISOLATED position o Wait 15 seconds E 15 seconds Activate a manual call point by inserting the test key ane Fire alarm with text and zonal indication will now be displayed on the control panel along with sounder operation set B Wait for 30 seconds 30 seconds Press the silence alarms button The time period shown is an average e time and maybe reduced if required dependant on the size of the system ie Press the Reset alarms button to reset the fire alarm event a ai The display should return to normal The key should be returned to the OFF position and removed from the control panel If applicable contact the alarm receiving centre and confirm that the test has been completed and verify signal received The test is now complete and the logbook should now be updated TEMPOINT USER MANUAL ISSUE 1 02 07 13 16 TemPomt 9 2 Setting the Time and Date To change the time and date turn the control key switch into the ON position Now press the 0 Key Press the V button once until gt Time and Date lt Is displayed Press th
18. n be changed if required by the Installer Maintenance Contractor Engineers Config This option when entered prompts for a PIN number to be entered to Allow access to Level 3 This menu is for Installer Maintenance Contractor use only Printer Options This option allows the Printer when fitted to be both Enabled and Disabled When Enabled and the option is set to ALL every Event is printed out This option can also be set to FIRE which will then only print Fire Events TEMPOINT USER MANUAL ISSUE 1 02 07 13 11 TemPomt 8 Alphanumeric Display Indicators There are two different types of Displays There is the Vacuum Fluorescent Display VFD type which displays up to 80 characters on a 4 line display This is used on the 96 zone model A Liquid Crystal Display LCD type is also available and is used on the 12 zone model There are different types of conditions that are shown on the display to suit different circumstances Below are some display indication screen shots 8 1 Non Alarm Conditions Under Non Alarm Conditions the display should show The Green Power LED should also be illuminated 8 15 Fire Event When a Fire event occurs the text on the display changes to show The above shows that Device 5 has generated a Fire event in Zone 1 TEMPOINT USER MANUAL ISSUE 1 02 07 13 12 TemPomt 8 2 Fire Networked Device When a device on a Networked Contro
19. n to highlight gt Status is Active lt and scroll through the different status types by pressing the YES key until desired option has been found then press the NO key three times to return to the main display Whilst a device is disabled the DETECTOR ZONE DISABLED LED Indicator will illuminate When the devices are enabled the LED Indicator will extinguish unless any detection zones are disabled 9 4 Enabling Disabling Zones To Enable Disable a zone from the main screen With the control key switch in the ON position press the 0 key then scroll down by pressing the V button to last option gt Fire System Options lt Press the YES key Now press the V button until highlighting gt Det Zone Dis Test lt Now press the YES key again Now press the 0 key and enter the desired Zone Number and press the YES key Press the V button and scroll through the different status types by pressing the YES key until desired option has been found then press the YES Key Now press the NO key until to return to the main display Whilst a zone is disabled the DETECTOR ZONE DISABLED LED Indicator will light When the zones are enabled the LED Indicator will extinguish unless a Detector is Disabled TEMPOINT USER MANUAL ISSUE 1 02 07 13 18 TemPomt 9 5 Enabling Disabling Brigade Relay To Enable or Disable the Brigade Re
20. nctions It is firstly Test used to reset a Fire Fault Event after the Silence Alarm button has been pressed and the Fire Fault Condition has been cleared It is secondly used to test all of the Systems Status Lamps This is achieved by pressing the button when the Systems Status is normal i e no events displayed Silence Alarms A This button Silences the System s Sounders and internal buzzers The panel will give an intermittent beep every 10 15 seconds until the condition is reset and will display Silence Alarms when pressed Sound Alarms a i This key is used for activating the System s Sounders The display will show Alarms Sounded when pressed View Tests 2 Feature Displays any device zone currently in test of key This will automatically timeout and return to the front screen if left in this mode View 2 Feature Displays any device zone currently Disablements of key disabled This will automatically timeout and return to the front screen if left in this mode View Faults 2 Feature Displays any device currently in fault of key condition This will automatically timeout and return to the front screen if left in this mode View Fires 2 Feature Returns to view fire events if any of the of key other view options used This will automatically timeout and return to the Front screen if left in this mode Status Lamps Indicates the systems current status see fig 2
21. nd return to the front screen if left in this mode Indicates the systems current status No Operation TEMPOINT USER MANUAL ISSUE 1 02 07 13 7 TemPoint 6 2 ON Position Functionality Access Level 2 ISOLATED OFF ON The Control Panel requires the control keyswitch turned to the ON Position enabling Access Level 2 The key may not be removed when in this position ON position Scroll Buttons N Operational when multiple events are KAKA E displayed to enable each event to be viewed Reset Led This button has two functions It is firstly Test F used to reset a Fire Fault Event after the Silence Alarm button has been pressed and the Fire Fault condition has been cleared It is secondly used to test all of the Systems Status Lamps This is achieved by pressing the button when the Systems Status is normal i e no events displayed Silence Alarms w This button Silences the System s Sounders and internal buzzers The panel will give an intermittent beep every 10 15 seconds until the condition is reset and will display Silence Alarms when pressed Sound Alarms ON This key is used for activating the System s Sounders The display will show Alarms Sounded when pressed View Tests 2 Displays any device zone currently in test Feature This will automatically timeout and return to of key the front screen if left in this mode View 2 Displays any device zone currently disabled Disablements Feat
22. of events up to 1000 events or to view the log at a certain date B Fire System FUNCTION DESCRIPTION Dev Disable Test This option enables an individual device that forms part of the fire system to be Disabled Activated or put into Test The status lamps will illuminate extinguish as appropriate Net Disable Test This option enables the user to control individual devices that are logged onto other control panel s on the Networked Fire System Such as a smoke detector or call point to be changed from their normal active status to be disabled or put into test Det Zone Dis Test This option allows the Detection Zone to be viewed and altered The zone can be either Active Test or Disable If any zones on the system are disabled or in test mode the relevant LED Indicators will light to indicate this Alarm Zone Disable This option allows the disablement of groups of sounders within the system The Alarm Zone can be either Enabled or Disabled If Disabled the relevant LED indicator will illuminate ARE Disable This option allows connection to the Fire Brigade via the Brigade Relay to be disabled Therefore any subsequent fire activation s will not operate this relay The panel operation although unaffected will display the text ARE BRIGADE DISABLED to ensure the system is not left in this mode System Mode This option allows enablement of up to eight different system modes of operation These are pre programmed and ca
23. played after the daily check at midday The fault would be displayed immediately when batteries are not present For any of these instances the following screen would be displayed 8 5 Fault PR Whenever the control panel s internal processor is reset including initial power up the following fault screen will be shown TEMPOINT USER MANUAL ISSUE 1 02 07 13 14 TemPoint 8 55 Fault RI Radio signal levels can vary due to the surrounding local environment The following screen shows that the controller is receiving unknown radio signals above an acceptable level The Fault RI represents that the panel is receiving Radio Interference 8 6 Fault OL This fault shows that a controller is currently Off Line on either a Hardwired or radio networked system This indicates the Control Panel is no longer communicating with the Network System If this has taken place the following fault screen will be shown TEMPOINT USER MANUAL ISSUE 1 02 07 13 15 TemPoint 9 Step by Step Guidance 9 1 Weekly Test Recommendations A manual call point should be tested on the system each week It is recommended that the test be carried out at the same time each week with any poor audibility instances reported A different manual call point should be tested each week to ensure that all call points are tested over time The results of the test and the call points used should be recorded in the logbook If the syste
24. ts sm 23 OTDI sr sn 23 10 2 Week eal aia 23 KOSK Oa ei iii ii sinengeniannieavanerneyivants 23 A e aaa Ma a A i capdeaatantawdatneactdngasasiucttndadaentantondarsans 23 Ma A AAA A 23 LL LOGBOOK tin aaa 24 TEMPOINT USER MANUAL ISSUE 1 02 07 13 3 TemPoint 1 Introduction This manual contains all of the information required for the use and operation of the EMS TemPoint This manual is also written in a format that presumes that the system has been correctly installed and commissioned When using the system it is important to follow this user manual at all times Any questions on the system should be put to the Installer Maintainer 1 1 Procedure In accordance with BS5839 Part 1 2002 written procedures must be established in dealing with alarms for Fire Fault Warnings and the Disablement of any part of the System A responsible person should be appointed who ensures that all users are instructed in the proper use of the system and are familiar with all associated procedures The nominated person shall also be responsible for liaising with the maintenance company on all matters relating to the maintenance of the system One of the associated procedures is to maintain an up to date logbook The logbook should include properly recorded events including all real and false alarms Also any testing or even temporary disablements should be noted Infact any events affecting the system should be recorded It should always be
25. ure This will automatically timeout and return to of key the front screen if left in this mode View Faults 20 Displays any device currently in fault Feature condition This will automatically timeout and of key return to the front screen if left in this mode View Fires 2 Returns to view fire events if any of the other Feature view options used This will automatically of key timeout and return to the front screen if left in this mode Status Lamps Indicates the systems current status see fig 2 System Menus N A Options and further Fire system Options Menus are now accessible by pressing the 0 Key Details are shown in Section 7 TEMPOINT USER MANUAL ISSUE 1 02 07 13 8 TemPoint 6 3 ISOLATED Position Functionality ISOLATED The Control Panel requires the control keyswitch turned to the aie Fl ISOLATED position Access Level 2 is accessible with the same Features as detailed previously and all control buttons are operational Plant Shutdown equipment can be disabled through this function as a N ko al A pre selected Sounder Group can be disabled This is normally used for isolating Plant Equipment whilst carrying out weekly tests However this is a programmable feature and can be configured by the installer maintenance contractor if required ISOLATED position Scroll Buttons xy Operational when multiple events are displayed to enable each event to be viewed Reset Led This button has two fu
Download Pdf Manuals
Related Search