User manual E 5
Contents
1. To mounting the BeSafe iZi Combi in forward facing remove the front brace 3 Remove the lower part of the support leg Fit the black plastic plug enclosed by purchase to the end of the support leg This will protect the orginal car seat cover Position the BeSafe iZi Combi on the car seat A ve AN SrA gt I Open both belt clamps 17 at each top side of the iZi Combi Bend down the flap on the seat cover See green arrow 14 p Pull out the seat belt place the hip belt over the bottom base of the iZi Combi Pull the hip belt over the metal hook and fasten the belt Guide the shoulder belt through the belt housings 17 at the top of each side of the child seat Press the iZi Combi well into the car seat First tighten the hip belt then the shoulderbelt starting at the bottom 15 Pull the shoulder belt through both belt housings and close the clamps The seat belt is now locked in position It is very important that the belt clamps are properly locked Use the rachet lever 5 to tighten the seat properly Check that the iZi Combi is firmly fixed if not repeat the prosedure from the beginning Fold up the flap and tighten it 16 NEVER use the forward facing installation before the weight of the child is over 9 kg NEVER use the iZi Combi forward facing installation without tighten the seat properly Al2. www besafe eu Complies with revised standard ECE R44 04 Tested and Approved User manual GROUP WEIGHT AGE O 1 0 18 6m 4y Z COMUILD TSS It is important that you read this user manual BEFORE installing your iZi Combi ISOfix Incorrect installation could endanger your child Vital information 3 Preparing to install 4 REARWARD FACING Before installation 6 REARWARD FACING Installation 8 REARWARD FACING Warning potential misuse 11 REARWARD FACING Removing 12 FORWARD FACING Installation 14 Sitting positions 18 Car seat protection 18 After an accident 19 Guarantee 19 Removing and refitting the cover 20 Important advice 22 Point of sale information 23 BeSafe advises that child seats should not be bought or sold second hand 2 d 7 Vital information iZi Combi ISOfix can be installed rearward facing In this position the car must be equipped with ISOfix anchorage points When iZi Combi ISOfix is installed forward facing the 3 point belt has to be used BeSafe iZi Combi ISOfix is approved in groups 0 and 1 rearward facing from 0 18 kg and group 1 forward facing from 9 18 kg We recommend to use the seat as long as possible in the rearward facing installation iZi Combi ISOfix is not allowed to mount in front passenger seat with an activated airbag For children under 1 year and or under 10 kg weight we recommend that the mo
3. and especially in cars with leather interior When installed with ISOfix Check the car manufacturer s handbook When the child weighs over 18 kg or the child s head ene ee 1 This is asemi universal ISOfix CHILD RESTRAINT SYSTEM It is approved to regulation No 44 04 series of amendments for general use in vehicles fitted with ISOfix anchorage systems 2 It will fit vehicles with positions approved as ISOfix positions as detailed in the vehicle handbook depending on category of the child seat and of the fixture 3 The mass group and the ISOfix size class for which this device is intended is C 4 The iZi Combi ISOfix is suitable for fixing into the seat positions of the cars listed in the appendix carlist Seat positions in other cars may also be suitable to accept this child retraint If in doubt consult either the child restraint manufacturer or the retailer For updated carlist see www besafe europe com 5 For ISOfix installation Make sure you read the car manufacturer s handbook 1 This seat can be used as an universal forward facing CHILD RESTRAINT SYSTEM with belt installation when your child is 9 18 kg 2 We recommend to use the seat as long as possible in the rearward facing installation for more information e A e NO 3535 Kr deren Norway www besafe europe com 2008 v1 1 d
4. brace first Turn the seat into the right position with the front brace against the backrest Push the floor support down to the floor The floor support 12 must go through the belt loop 14 and the belt loop must be led into the hook on the floor support See explanation in the chapter BEFORE INSTALLATION d a gt Pull both ISOfix connectors 7 as far out as possible The switch 4 then goes into the lowest position and locks the connectors 7 Click the ISOfix connectors in the ISOfix anchorages Make sure that the two indica tors 10 are green both in the hole and on the inside of the release gear Adjust the floor support 12 so that it is in contact with the floor of the vehicle Lock the floor support with the lockingbolt 13 Adjust the front brace outwards with the ratchet 6 Continue tightening until the brace is pressed well into the backrest of the car seat If possible push the front seat backwards so that it is in contact with the child seat If it is not possible to obtain contact with the child seat push the backrest of the front seat forward so that the distance between child seat and backrest is minimum 25 cm Make sure the floor support is fully pushed down and locked when mounting rearward facing Make sure all ISOfix indicators are green before you drive DO NOT use on a passenger seat fitted with activa
5. is no receipt When defects are caused by wrong and improper use When defects are caused by abuse misuse or negligence 19 Never use the iZi Combi ISOfix without the cover The cover is part of the system and may only be replaced by an original iZi Combi ISOfix cover ALWAYS use the child safety belt provided with the iZi combi ISOfix Pay attention when you remove the cover as fitting the cover is done in the opposite way To remove the cover the child Seat hip belt must be released at both sides See red arrow Race the seat part of the cover and unhook both belts from the metal hooks in the bottom of the seat The cover can now be removed When fitting the cover start by hooking the hip belts to the hooks in the bottom of the seat Pull hard in the belts to ensure that they are correctly installed To bring the cover under the rear part of the sidewall turn it inside out and guide it under the sidewall before straighten ing it out The cover of the iZi Combi ISOfix must be washed in accordance with the instructions on the inside of the cover YAX AKA DO NOT use any cleaning products these may harm the construction material of the iZi Combi ISOfix DO NOT use on a passenger seat fitted with ee activated frontal airbag S ALWAYS use the child safety belt provided with the iZi Combi ISOfix at all times Warrant
6. ront seat adjust the backrest in a upright position Find the ISOfix anchorage points in the car 15 If your car is not epuipped with ISOfix insertion clips 16 insert these to make installation easier You can find the ISOfix insertion 16 clips under the base of your iZi Combi ISOfi x Clip the insertion clips into the anchorage points Important The belt loop must be led into this hook Remove the plastic caps 9 from the ISOfix connectors 7 by pressing down the ISOfix release button 8 Use the ratchet 6 to adjust the front brace to the inmost position The ratchet 6 is used to adjust the front brace in both directions Switch the knobs on the ratchet to change direction Assemble the floor support before you install the iZi Combi ISOfix in your car The floor support 12 must go through the belt pi loop 14 The belt loop 1 must also be led into the ts hook on the floor support Do not fasten the locking bolt 13 yet d Z REARWARD FACING Installation in the car The BeSafe iZi Combi ISOfix can ONLY be installed rearward facing in cars with ISOfix anchorage points N The BeSafe iZi Combi ISOfix must not be used in the front passenger seat without deactivating the airbag BeSafe iZi Combi ISOfix is installed the same way in the front and back seat Place the seat into the car by racing the seat with the front
7. st reclined sitting position is used We recommend that this seat is used only for children who can sit upright so not younger than 6 months The floor Support must always be used when it is installed rearward facing in cars with ISOfix When installing forward facing the floor support and the front brace shall not be used When installed with a 3 point belt Only suitable if the approved vehicles are fitted with 3 point belts approved to UN ECE Regulation No 16 or other equivalent standards The harness must always be used when the child is in the seat Under the fabric cover we use EPS foam Do not push or pull too hard against the foam since you might damage the foam a i i nN Preparing to install Crucial parts 1 Internal harness 2 Harness adjustment 3 Front brace 4 Switch for ISOfix connectors 5 Lever for sleeping positions 6 Ratchet for front brace 7 1SOfix connectors a 8 Release button for ISOfix connectors a ce aa 7 1SOfix installation connectors 9 Plastic caps for the ISOfix connectors 10 Indicator for correct installation 11 Belt height adjuster 12 Floor support 13 Lockingbolt for floor support 14 Belt loop for the floor support 15 1SOfix anchorage car 7 1SOfix connector 16 1SOfix insertion clips Height adjustment of harness system Position of the shoulder strap C C Check that the shoulder s
8. ted frontal airbags AIRBAG 10 d NEVER use BeSafe iZi Combi ISOfix without the floor Support when mounting rearward facing NEVER use BeSafe iZi Combi ISOfix without tightening the front brace when mounting rearward facing ALWAYS make sure that the indicator for correct installation of the ISOfix anchorages shows GREEN N NEVER USE iZi Combi ISOfix on a passenger seat fitted with activated frontal airbag a 12 If your iZi Combi ISOfix is installed in the back seat push the front seat as far forward as possible Adjust the backrest as far backwards as possible when removing from the front seat Remove the locking bolt 13 from the floor support 12 Use the front brace ratchet 6 to adjust the front brace 3 towards the iZi Combi ISOfi x base Release the ISOfix connectors by pressing the release mechanism 8 on the ISOfix installation connectors Now the indicator for right installation 10 shows red and not green gt Push the switch 4 on each side and push the ISOfix installation connectors 7 into the base Pull the iZi Combi ISOfix back towards the front seat Turn the seat so you can easily remove the seat Remove your iZi Combi z ISOfix from the car Remove the insertion clips 16 from the car seat Place them under the base of the iZi Combi ISOfi x r p
9. trap ay Slots are levelled with your child s shoulders Toohigh Toolow Correct Pull out the shoulder belts while pressing the button on the harness adjustment mechanism Height can be adjusted by releasing the height adjustment device on the back of the iZi Combi ISOfix place it in the correct position and clicking it in Twist and pull the Shoulder belts on the front side of the seat until the belts are adjusted into the correct position Check the webbing has not become twisted Tighten the belts by pulling them towards you and in this way straighten them out inside the construction e Lay the shoulder straps over the sides of the iZi Combi ISOfix before your child is seated Then place the straps over the shoulders of your child and close the buckle Click eas the child s shoulders Place one hand on the front of the car seat and pull the harness adjustment strap towards you Continue pulling until the harness is a comfortable but firm fit Q Position the pads on the shoulder straps over You must adjust the shoulder belt of the harness to the correct position for your child before installing the seat as it cannot be adjusted in the car The harness must be fastened and adjusted correctly at all times Children should be encouraged to remain within the harness system AIRBAG When mounting in the back seat push the front seat as far forward as possible When mounting in the f
10. ways check that the iZi Combi is firmly fixed NEVER USE iZi Combi ISOfix on a passenger seat fitted with activated frontal airbag x 17 d Sitting positions BeSafe iZi Combi ISOfix has 4 sitting positions The sitting positions can be regulated by using the lever 5 5 Car seat protection To avoid damage to the fabric of the car seat especially with leather car seats protect your car seat with a BeSafe protection cover After an accident the iZi Combi ISOfix must be replaced Although it may look undamaged if you were to have another accident the iZi Combi ISOfix may not be able to protect your child as well as it should All BeSafe products are carefully designed manufactured and tested All of our BeSafe child safety seats are tested periodically out of our continuous production in our test laboratory Furthermore they are tested by independent test institutes Should this product prove faulty within 24 months of purchase due to materials or manufacturing fault except covers and child safety belt please return it to the original place of puchase The guarantee is only valid when you use your seat appropriately and with care Please contact your dealer he will decide if the seat will be returned to the manufacturer for repair Replacement or return cannot be claimed The guarantee does not get extended through repair The guarantee expires When there
11. y will expire if non original parts or accessories are used Never leave your child unattended in an iZi Combi ISOfix Make sure all passengers are informed about how to release your child in case of emergency An unoccupied iZi Combi ISOfix should still be fastened Make sure luggage or other objects are properly secured Unsecured luggage may cause severe injuries to children and adults in case of accidents Never use the iZi Combi ISOfix without the cover The cover is a safety feature and may only be replaced by an original iZi Combi ISOfix cover The cover of the iZi Combi ISOfix must be washed in accordance with the instructions Do not use any aggresive cleaning products these may harm the construction material of the iZi Combi ISOfix 22 d KEEP this user manual for later use DO NOT attempt to dismantle modify or add any part to the iZi Combi ISOfix DO NOT use anything such as a cushion to raise the iZi Combi ISOfix off the passenger seat In an accident the iZi Combi ISOfix will not be able to protect your child as well as it should DO NOT use the iZi Combi ISOfix for longer than 5 years Due to ageing the quality of the material may change DO NOT use at home It has not been designed for home use and can only be used in a car We recommend using BeSafe protection cover under your child safety seat to avoid cuts marks or decolouring on the interior of the car
Download Pdf Manuals
Related Search