Home

Honeywell Minitrend V5 Service Manual

1. FIGURE 6 4 The Earthing Screw If fitted replace and tighten the mount ing clamp screws at the top and bottom of the extrusion 11 00 UK 21 Honeywell Connection Details Ethernet Interface This is an 8 way RL45 socket Molex 95040 288 used for Ethernet connection pcb position J5 Standard Ethernet connection 7 TD TD RD 1 RD O0 N O O P2 O0 N On pO OOOO PLP locating pins O not connected a RS232 Interface Comm2 This is a 9 way D type connector mating half not supplied pcb position P1 77 e O 9 R12 O 4 DTR2 o 8 CTS2 o 3 TXD2 o 7 RTS2 o 2 RXD2 o 6 DSR2 OF 1 DCD2 RS485 Interface Comm3 Trendbus This is a 5 way socket mating half supplied pcb position TXA J1 22 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Chapter 7 Minitrend V5 Processor Card Installation Removal of the rear panel ONLY is necessary when this operation is intended Removing the Rear Panel A CAUTION OBSERVE ANTI STATIC PRECAUTIONS Refer to BS EN1000151 1992 Basic specification Protection of electrostatic sensitive devices Full anti static precautions MUST be observed when in contact with the electronics within the recorder Removal of PCBs and battery back up will result in the loss of all non volatile data Ensure all data and set ups are saved first F
2. Replace fit the earth screw and shakeproof washer on the side of the dividing panel using a short reach screwdriver torque to 120cNm or 10 62lbf in FIGURE 12 2 The Earthing Screw Re assembling the Unit Remove the plastic blanking plate safety cover for the appropriate slot on the rear panel if necessary by pushing out the push rivets from behind Replace the rear panel reposition the toothed washers and replace and tighten the four M4 x 8mm pozi pan head self tap screws at each corner of the rear panel 43 TV 25 10 GLO Issue 2 11 00 UK 41 Honeywell 42 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Chapter 13 Multitrend Plus V5 Alarm Card Installation Removal of the rear panel ONLY is necessary when this operation is intended Removing the Rear Panel A CAUTION OBSERVE ANTI STATIC PRECAUTIONS Refer to BS EN1000151 1992 Basic specification Protection of electrostatic sensitive devices Full anti static precautions MUST be observed when in contact with the electronics within the recorder Removal of PCBs and battery back up will result in the loss of all non volatile data Ensure all data and set ups are saved first Failure to comply with these instructions may result in product damage e To remove the rear panel of the recorder loosen and remove the four M4 x 8mm self tap screws at each corner of the rear panel taking care to retain both the shakeproof washer and the screw FIG
3. e f fitted loosen and remove the mounting clamp screws M3 x 16mm pan pozi at the top and bottom of the extrusion to allow removal of the back panel NB Only one of the two screws may have to be removed while loosening the other will be sufficient 43 TV 25 10 GLO Issue 2 11 00 UK 3 Honeywell Inside the Unit DO NOT disconnect any wiring from the mains socket on the rear panel Gently move the rear panel to the side of the extrusion to allow internal access 1 Power Supply Card Analogue Card A Analogue Card B Comms Card C N Processor Card Alarm Card D PCMCIA Card behind the alarm card N el A 5 9 8 Disk Drive FIGURE 2 2 Position of the internal boards Standard and Universal Analogue Cards The mechanical constraints for the standard analogue card and the universal analogue card are the same The installation for either of the analogue cards in slot A or slot B positions follows the same procedure The analogue slot A on the rear panel is primarily for the standard analogue card and slot B for the universal analogue card However either slot can be used for both types of analogue card Removing the Analogue Card e f replacing an analogue card remove any cards as necessary from slot A or slot B positions This is done simply by locating the earthing screw on the left side of the unit looking from the rear Slot A s earthing screw is second fr
4. Honeywell Remove the alarm card at the same time FIGURE 3 3 Alarm card Slide the processor board out to reveal a 34 way connector on the under side of the card Remove the connector if replacing an alarm card Plug one end of the new alarm ribbon cable into the connector on the processor card NB Both ends of the ribbon cable are identical The connector will only fit in one way round identified by a location tab at one side of the connector Push the connectors fully into the socket on the card Connect the other end of the ribbon cable in to the 34 way connector on the alarm card Inserting the Alarm Card Fit a snubber card into alarm slot D if a PCMCIA card is not fitted Begin to slide the processor card back into its slot holding the alarm card parallel below allowing the ribbon cable to bend into a comfortable S shape See Figure 3 4 on page 9 Both the cards need to be inserted simultaneously to keep the ribbon cable in its folded S shape position Slide the cards carefully back into the extrusion until the fixing bracket on the left side of both cards are in line with the single fixing hole on the side of the extrusion Ensure that no internal wiring is dam aged as the alarm card is returned The processor card will locate into a FIGURE 3 4 Alarm Ribbon Cable mating connector in the mother board at the front of the unit Ensure the card is pushed fully home 43 TV 25 10 GLO I
5. Inserting the Primary Alarm Card in slot D PCMCIA Care if fitted Fit snubber card into alarm slot D if a PCMCIA card is not fitted Begin to slide the processor card back into its slot holding the alarm card parallel below allowing the ribbon cable to bend into a comfortable S shape Both the cards need to be inserted simultaneously to keep the ribbon cable in its folded S shape position Comms Card if fitted Processor Card 4 way alarm ribbon cable connector Alarm Card FIGURE 13 3 The alarm card plugs in underneath the processor card 43 TV 25 10 GLO Issue 2 11 00 UK 45 Honeywell 46 Slide the cards carefully back into the extrusion until the fixing bracket on the left side of the cards are in line with the single fixing hole on the side of the extrusion Ensure that no internal wiring is damaged as the alarm card is returned The processor card will locate into a connector at the front of the unit Ensure the card is pushed fully home The alarm card does not locate into a connector but needs the earth bracket align ing with the fixing hole on the side of the unit Align the processor card with its fixing hole and earth bracket Replace the earth screw and shakeproof washer on the side of the extrusion torque to 120cNm or 10 62Ibf in FIGURE 13 4 T he Earthing Screws 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Inserting a Second Alarm Card in slot DI e A second alarm card
6. 7 PCMCIA Card behind the alarm card ela 8 Disk Drive FIGURE 3 2 Position of the internal boards Alarm Cards There are two main types of alarm cards the relay alarm card and the input output card For the Minitrend V5 the relay alarm card is available with 4 or 8 channels of relay out put the 8 channel having two channels of digital input as standard The input output cards for the Minitrend V5 are available with 8 or 16 channels all channels may be used as digital inputs All alarm cards take up position in slot D on the rear panel of the Minitrend V5 If the unit is not fitted with a PCMCIA card in the alarm slot D a snubber card will be required Removing the Alarm Card It is necessary to access the processor card to connect one end of the alarm ribbon cable to the socket on the under side of the card e Locate the earth bracket screw for the processor card on the left side of the unit from the rear second position from the bottom of the unit Slot C Remove and retain the screw and shakeproof washer e f the alarm card is being replaced locate and remove the earthing screw from the bottom position of the unit Slot D Remove the card and retain both the screw and the shakeproof washer e Grip the front of the processor card or by the connector and gently pull to release the card from its connection to the mother board at the front of the unit 8 43 TV 25 10 GLO Issue 2 11 00 UK
7. LOMAS ALTAS 11950 MEXICO CITY MEXICO Tel 52 5 259 1966 THE NETHERLANDS HONEYWELL BV Laaderhoogtweg 18 1101 EA AMSTERDAM ZO THE NETHERLANDS Tel 31 20 56 56 911 NORWAY HONEYWELL A S Askerveien 61 PO Box 263 N 1371 ASKER NORWAY Tel 47 66 76 20 00 POLAND HONEYWELL Sp z 0 0 UI Domainewksa 41 02 672 WARSAW POLAND Tel 48 22 606 09 00 PORTUGAL HONEYWELL PORTUGAL LDA Edificio Suecia II Av do Forte nr 3 Piso 3 2795 CARNAXIDE PORTUGAL Tel 351 1 424 50 00 REPUBLIC OF IRELAND HONEYWELL Unit 1 Robinhood Business Park Robinhood Road DUBLIN 22 Republic of Ireland Tel 353 1 4565944 REPUBLIC OF SINGAPORE HONEYWELL PTE LTD BLOCK 750E CHAI CHEE ROAD 06 01 CHAI CHEE IND PARK 1646 SINGAPORE REP OF SINGAPORE Tel 65 2490 100 REPUBLIC OF SOUTH AFRICA HONEYWELL Southern Africa PO BOX 138 Milnerton 7435 REPUBLIC OF SOUTH AFRICA Tel 27 11 805 12 01 ROMANIA HONEYWELL Office Bucharest 147 Aurel Vlaicu Str Sc Z Apt 61 62 R 72921 Bucharest ROMANIA Tel 40 1 211 00 76 21179 RUSSIA HONEYWELL INC 4 th Floor Administrative Builiding of AO Luzhniki Management 24 Luzhniki 119048 Moscow RUSSIA Tel 7 095 796 98 00 01 SLOVAKIA HONEYWELL Ltd Miynske nivy 73 PO Box 75 820 07 BRATISLAVA 27 SLOVAKIA Tel 421 7 52 47 400 425 SPAIN HONEYWELL S A Factory Josefa Valcarcel 24 28027 MADRID SPAIN Tel 34 91 31 361 00 SWEDEN HONEYWELL A
8. 3 Analogue Card A1 4 Analogue Card B1 5 Comms Card C 6 Processor Card C 7 PCMCIA Card D behind the alarm card 8 Alarm Card 9 Transmitter Power Supply Card 10 Mother Board 11 Power Supply 12 Disk Drive 24444111 EMMA 44411141 E sanidad N FIGURE 15 2 Position of the internal boards There are two types of retransmission cards one has two channels of retransmission and the other has 4 channels As analogue cards take the positions of slot A and slot B the preferred slot for the retransmission card is A1 B1 is used if two retransmission cards are fitted and if three analogue cards are fitted B A1 and B1 are used 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Removing the Retransmission Card If replacing a retransmission card remove any cards as necessary from either slot A1 or slot B1 positions slot A1 is preferred This is done simply by locating the earthing screw on the left side of the dividing panel in the middle of the unit looking from the rear Slot A1 s earthing screw is third from the top and slot B1 s earthing screw is fourth from the top Grip the card by its connector and gently pull to release the card from its connection to the mother board Inserting the Retransmission Card Re assembling 43 TV 25 10 GLO Issue 2 Slide the retransmission card carefully back into the extrusion until the fixing bracket on the left side of the retransmission card is in l
9. A CAUTION OBSERVE ANTI STATIC PRECAUTIONS Refer to BS EN1000151 1992 Basic specification Protection of electrostatic sensitive devices Full anti static precautions MUST be observed when in contact with the electronics within the recorder Removal of PCBs and battery back up will result in the loss of all non volatile data Ensure all data and set ups are saved first Failure to comply with these instructions may result in product damage e To remove the rear panel of the recorder loosen and remove the four M4 x 8mm self tap screws at each corner of the rear panel taking care to retain the screws and shakeproof washers FIGURE 19 1 Removing the rear panel 43 TV 25 10 GLO Issue 2 11 00 UK 71 Honeywell Replacing the Rear Panel Assembly Remove from the power supply the 3 way mains filter loom connecting the live and neutral wires from the rear panel assembly blue and brown wires Disconnect the earth lead from the mains filter on the rear panel assembly green yellow If a transmitter power supply card is fitted remove the 3 way mains filter loom con necting the live and neutral wires from the rear panel assembly blue and brown wires and disconnect the earth lead from the mains filter on the rear panel assem bly green yellow These connections will be fitted with piggy back spade terminals on the mains filter Connect the 3 way mains filter loom from the new rear panel assembly to the power supply
10. B S 127 86 Skarholmen STOCKHOLM SWEDEN Tel 46 8 775 55 00 SWITZERLAND HONEYWELL A G Hertistrasse 2 8304 WALLISELLEN SWITZERLAND Tel 41 1 831 02 71 TURKEY HONEYWELL Otomasyon ve Kontrol Sistemlen San ve Tic A S Honeywell Turkey A S Emirhan Cad No 144 Barbaros Plaza C Blok Kat 18 Dikilitas 80700 Istanbul TURKEY Tel 90 212 258 18 30 UNITED KINGDOM HONEYWELL Unit 1 2 amp 4 Zodiac House Calleva Park Aldermaston Berkshire RG7 8HW UNITED KINGDOM Tel 44 118 906 2600 U S A HONEYWELL INC INDUSTRIAL CONTROLS DIV 1100 VIRGINIA DRIVE PA 19034 3260 FT WASHINGTON U S A Tel 1 800 343 0228 VENEZUELA HONEYWELL CA APARTADO 61314 1060 CARACAS VENEZUELA Tel 58 2 239 0211 This publication does not constitute a contract between Honeywell and its customers The contents may be changed at any time without notice It is the cus tomer s responsibility to ensure safe installation and operation of the products Detailed mounting drawings of all products illustrated are available on request Honeywell 2000 All rights reserved Honeywell Sensing and Control www honeywell com sensing Honeywell 4 Airfield Way Christchurch BH23 3TS Dorset U K 43 TV 25 10 GLO Issue 2 11 00 UK
11. Ensure the card is pushed fully home and that no internal wiring is damaged as the power supply card is returned Replace fit the earth screw and shakeproof washer on the side of the extrusion torque to 120cNm or 10 62lbf in Re assembling the Unit Replace the rear panel reposition the shakeproof washers and replace and tighten the four No 6 x 12 self tap screws at each corner of the rear panel Replace and or tighten the mounting clamp screws at the top and bottom of the extrusion FIGURE 4 4 The Earthing Screw 43 TV 25 10 GLO Issue 2 11 00 UK 13 Honeywell 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Chapter 5 Minitrend V5 Retransmission Card Installation Removal of the rear panel ONLY is necessary when this operation is intended Removing the Rear Panel A CAUTION OBSERVE ANTI STATIC PRECAUTIONS Refer to BS EN1000151 1992 Basic specification Protection of electrostatic sensi tive devices Full anti static precautions MUST be observed when in contact with the electronics within the recorder Removal of PCBs and battery back up will result in the loss of all non volatile data Ensure all data and set ups are saved first Failure to comply with these instructions may result in product damage e To remove the rear panel of the recorder loosen and remove the four No 6 x 12 self tap screws at each corner of the rear panel taking care to retain the shakeproof washer under each sc
12. Remove and retain the screws and shakeproof washers Grip the front of the card or by the connector and gently pull to release the card from its connection to the mother board at the front of the unit If there is an alarm card fitted in the slot below slot D there will be a 34 way con nector attached to the underside of the processor card this must be disconnected before the processor card can be removed If there is a comms card fitted this will be a separate card plugged into the top of the processor card it will need to be removed from the processor card To do this pull the cards out and turn them over to show the underside of the processor card Remove the two screws and shakeproof washers from the two pillars connecting the two cards together from the underside of the processor card Carefully separate the comms card from the processor card Begin to pull the two boards apart rotating them 90 each time There are three double row headers in different orientations therefore pulling from alternate side will ease the process See Figure 7 3 on page 25 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell FIGURE 7 3 The comms card plugs in on top of the processor card do a wi Inserting the Processor Card Re assembling 43 TV 25 10 GLO Issue 2 Plug in the comms card if fitted to the processor card and replace the two screws and shakeproof washers on the underside of the processor card to secure the pil lar
13. a PCMCIA memory card See Minitrend V5 Alarm Card Installation on page 7 and Minitrend V5 PCMCIA Card Installation on page 27 Disk Drive Installation 34 e Remove all the cards from slots A B C D and the power supply card from the top slot Disconnect the 2 way disk drive power lead red and black from the power supply card e Remove power supply and signal loom from disk drive e Unscrew the four fixing screws from the left side of the unit remove and retain the screws and remove the disk drive 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Re assembling 43 TV 25 10 GLO Issue 2 Position the new disk drive over the mounting holes and replace using the original screws Fit power supply and signal leads to new disk drive Reconnect the disk drive power lead to the power supply card Replace the power supply card in to the top slot Replace the analogue cards in slot A or B or both Replace the processor card in slot C Replace any cards in slot D the Unit Replace the rear panel reposition the shakeproof washers and replace and tighten the four No 6 x Y self tap screws at each corner of the rear panel Replace and or tighten the mounting clamp screws at the top and bottom of the extrusion 11 00 UK 35 Honeywell 36 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Chapter 11 Minitrend V5 Display Assembly Display Assembly Replacement The display assembly comprises of the f
14. in slot D1 an alarm interface card is required which plugs into the mother board Up to a total of 32 alarm channels are available 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Removing the Primary Alarm Card in slot D It is necessary to access the processor card to connect one end of the alarm ribbon cable to the socket on the under side of the card Locate the earth screw for the processor card on the left side of the dividing panel in the middle of the unit from the rear The processor card earth screw is second from the bottom of the unit C Remove and retain both screw and shakeproof washer using a short reach screw driver Remove the earth screw and washer for the alarm card in the same way The pri mary alarm card occupies the bottom position D Retain both the screw and the shakeproof washer Slide the processor board out to reveal a 34 way connector on the under side of the processor card Remove the existing ribbon cable connector if necessary Plug in new alarm ribbon cable to the under side of the processor card NB Both ends of the ribbon cable are identical The connector will only fit in one way round Connect the other end of the ribbon cable in to the 34 way connector on the alarm card This is identified by a location tab on one side of the connector Push the connec tors fully into the socket on the card Connect the other end of the alarm ribbon cable into the 34 way connector on the alarm card
15. remove the rear panel of the recorder loosen and remove the four M4 x 8mm self tap screws at each corner of the rear panel taking care to retain the screws and shakeproof washers FIGURE 16 1 Removing the rear panel 43 TV 25 10 GLO Issue 2 11 00 UK 57 Honeywell Inside the Unit DO NOT disconnect any wiring from the mains socket on the rear panel Gently move the rear panel to the side of the case to allow internal access 1 Analogue Card A 2 Analogue Card B 3 Analogue Card A1 4 Analogue Card B1 5 Comms Card C 6 Processor Card C 7 PCMCIA Card D behind the alarm card 8 Alarm Card 9 Transmitter Power Supply Card 10 Mother Board 11 Power Supply 12 Disk Drive 58 NIS e PRIN Is Is Ss FIGURE 16 2 Position of the internal boards 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Communications and RS485 Cards The mechanical constraints for the comms card and the RS485 card are the same The comms cards plugs onto the processor card like a piggy back board which occupies slot C Removing the Comms Cards If replacing a comms card it is necessary to partially slide out the processor card This is done by locating the earthing screw on the left side of the dividing panel in the middle of the unit looking from the rear Slot C earthing screw is second from the bottom remove and retain screw and shakeproof was
16. same Score on a level of 1 10 with 10 being the best Quality of manuals sales literature Administration documentation and letters Technical expertise of our sales staff Sales staff ability to give informed advice The quality of the Honeywell sales team Pricing Honeywell understanding of your industry 43 TV 25 10 GLO Issue 2 11 00 UK How do you perceive our range of products Tick as appropriate Products offered are better than those of competitors Products offered are worse than those of competitors Products offered are the same as those of competitors Any other comments Are there any products that we do not provide that you would like us to provide or any we could improve on If you are an existing or new customer what made you choose Honeywell Only on price Price plus a combination of factors Prefer to deal with a reputable company Honeywell offers more than the competition in terms of added value over and above the product itself Thank you for completing this questionnaire Please fill out your name and address below Photo copy this form and Fax to us on 44 0 1202 476501 79 Warranty Remedy Honeywell warrants goods of its manufacture as being free of defective material and faulty workmanship Contact your local sales office for warranty in
17. the board guides of slot D The processor card will then locate along the board guides for slot C When the processor card is half way in reconnect the ribbon cable display connec tor and the 5 way connector for the backlight If an alarm card is fitted begin to slide it in behind the PC card keeping the ribbon cable flat to the alarm card All the boards should slide in together with the processor card locating into a mating connector on the mother board at the front of the unit Insert the processor card fully until the fixing bracket on the left side of the proces sor card is in line with the single fixing hole on the side of the dividing panel in the middle of the unit Line up the alarm card and replace the earthing screw in the same way Ensure the card is pushed fully home and that no internal wiring is damaged as the alarm card is returned Replace the earth screw and toothed washer on the side of the case torque to 120cNm or 10 621bf in FIGURE 18 4 The Earthing Screws Re e the Unit 70 Remove the plastic blanking plate safety cover for the appropriate slot on the rear panel if necessary by pushing out the push rivets from behind Replace the rear panel reposition the toothed washers and replace and tighten the four M4 x 8mm self tap screws at each corner of the rear panel 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Chapter 19 Multitrend Plus V5 Rear Panel Assembly Removing the Rear Panel
18. the rear panel if necessary by pushing out the push rivets from behind Replace the rear panel reposition the toothed washers and replace and tighten the four M4 x 8mm self tap screws at each corner of the rear panel 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Chapter 15 Multitrend Plus V5 Retransmission Card Installation Removal of the rear panel ONLY is necessary when this operation is intended Removing the Rear Panel A CAUTION OBSERVE ANTI STATIC PRECAUTIONS Refer to BS EN1000151 1992 Basic specification Protection of electrostatic sensitive devices Full anti static precautions MUST be observed when in contact with the electronics within the recorder Removal of PCBs and battery back up will result in the loss of all non volatile data Ensure all data and set ups are saved first Failure to comply with these instructions may result in product damage e To remove the rear panel of the recorder loosen and remove the four M4 x 8mm self tap screws at each corner of the rear panel taking care to retain the screws and shakeproof washers FIGURE 15 1 Removing the rear panel 43 TV 25 10 GLO Issue 2 11 00 UK 53 Honeywell Inside the Unit DO NOT disconnect any wiring from the mains socket on the rear panel Gently move the rear panel to the side of the case to allow internal access Retransmission Card 54 Analogue Card A 2 Analogue Card B
19. this manual two basic safety tests should be performed in order to ensure continued safe operation of the instrument 1 Earth Resistance 25 Adc applied between case and protective earth bonding resistance should be 0 1 Ohm 2 Insulation Resistance 500Vdc applied between the earth terminal and the live and neutral terminal shorted together insulation resistance to be gt 2 0 MOhm Mega Ohm NOT milli Ohm Failure to comply with these instructions may result in product damage 43 TV 25 10 GLO Issue 2 11 00 UK 1 Honeywell 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Chapter 2 Minitrend V5 Analogue Card Installation Removal of the rear panel ONLY is necessary when this operation is intended Removing the Rear Panel A CAUTION OBSERVE ANTI STATIC PRECAUTIONS Refer to BS EN1000151 1992 Basic specification Protection of electrostatic sensi tive devices Full anti static precautions MUST be observed when in contact with the electronics within the recorder Removal of PCBs and battery back up will result in the loss of all non volatile data Ensure all data and set ups are saved first Failure to comply with these instructions may result in product damage e To remove the rear panel of the recorder loosen and remove the four No 6 x self tap screws at each corner of the rear panel taking care to retain the screws and the shakeproof washers FIGURE 2 1 Removing the rear panel
20. this operation is intended Removing the Rear Panel A CAUTION OBSERVE ANTI STATIC PRECAUTIONS Refer to BS EN1000151 1992 Basic specification Protection of electrostatic sensi tive devices Full anti static precautions MUST be observed when in contact with the electronics within the recorder Removal of PCBs and battery back up will result in the loss of all non volatile data Ensure all data and set ups are saved first Failure to comply with these instructions may result in product damage e To remove the rear panel of the recorder loosen and remove the four No 6 x self tap screws at each corner of the rear panel taking care to retain the screws and shakeproof washers FIGURE 6 1 Removing the rear panel e f fitted loosen and remove the mounting clamp screws M3 x 16mm pan pozi at the top and bottom of the extrusion to allow removal of the back panel NB Only one of the two screws may have to be removed while loosening the other will be sufficient 43 TV 25 10 GLO Issue 2 11 00 UK 19 Honeywell Inside the Unit DO NOT disconnect any wiring from the mains socket on the rear panel Gently move the rear panel to the side of the extrusion to allow internal access 1 Power Supply Card 2 Analogue Card A 3 Analogue Card B 4 Comms Card C 5 Processor Card 6 Alarm Card D 7 PCMCIA Card behind the alarm card 8 Disk Drive FIGURE 6 2 Posi
21. 0 UK Honeywell FIGURE 6 3 The comms card plugs in on top of the processor card Inserting the Comms Cards Re assembling 43 TV 25 10 GLO Issue 2 Plug in the new comms card to the processor card and replace the two screws and shakeproof washers on the underside of the processor card to secure the pillars locking the two cards together Begin to slide the processor card back into the extrusion If an alarm card is fitted ensure the ribbon cable is reconnected to the underside of the processor card and kept flat to the alarm card Insert the processor card fully until the earth fixing bracket on the left side of the processor card is in line with the single fixing hole on the side of the extrusion The processor card will locate into a mating connector in the mother board at the front of the unit Ensure the card is pushed fully home and that no internal wiring is damaged as the alarm card is returned Replace fit the earth screw and shakeproof washer on the side of the extrusion torque to 120cNm or 10 62Ibf in the Unit Remove the plastic blanking plate safety cover for the appropriate slot on the rear panel if necessary by pushing out the push rivets from behind Replace the rear panel reposition the shakeproof washers and replace and tighten the four No 6 x self tap screws at each corner of the rear panel Replace and or tighten the mounting clamp screws at the top and bottom of the extrusion
22. 000151 1992 Basic specification Protection of electrostatic sensitive devices Full anti static precautions MUST be observed when in contact with the electronics within the recorder Removal of PCBs and battery back up will result in the loss of all non volatile data Ensure all data and set ups are saved first Failure to comply with these instructions may result in product damage e To remove the rear panel of the recorder loosen and remove the four No 6 x self tap screws at each corner of the rear panel taking care to retain the screws and shakeproof washers FIGURE 9 1 Removing the rear panel e f fitted loosen and remove the mounting clamp screws M3 x 16mm pan pozi at the top and bottom of the extrusion to allow removal of the back panel NB Only one of the two screws may have to be removed while loosening the other will be sufficient 43 TV 25 10 GLO Issue 2 11 00 UK 31 Honeywell mains filter loom FIGURE 9 2 Power supply card and rear panel assembly connections Replacing me Rear Panel Assembly Remove from the power supply card the 3 way mains filter loom connecting the live and neutral wires from the rear panel assembly two wire one brown and one blue Disconnect the earth lead from the mains filter on the rear panel assembly green yellow wire Connect the 3 way mains filter loom from the new rear panel assembly to the power supply card Connect the earth lead from the power supp
23. 1 00 UK Honeywell Chapter 9 Minitrend V5 Rear Panel Assembly 31 Removing the Rear Panel esssssssnsnssssnsnsssessnsnsnssnsnensesensnsnsnssnsnsnsssensnensensnsnensensnsnnns 31 Replacing the Rear Panel Assembly ssssnsnsssessnsnsessnsnsnssnsnsnsnsensnensessnsnensnsensnensenen 32 Re assembling the Unit Chapter 10 Minitrend V5 Disk Drive Replacement 33 Removing the Rear Panel esssssssnsnsssensnsnsessnsnsnssnsnensssensnsnsnssnsnsnsssensnensensnsnensessnenens 33 Inside the Unit 34 Disk Drive Replacement usassssssssnensessnsnsnsessnsnsnssnsnensssensnsnsnssnsnsnssssnsnensessnsnenssssnennns 34 Disk Drive Installation uessssnsssssssnensensnsnsssessnsnsnsensnensnsensnsnsnssnsnsnsnssnsnensensnsnnsensnenens 34 Re assembling the Unit esessssssnensesensnsnsnssnsnsnssssnsnensensnsnensensnsnsnssnsnensensnsnensnsensnnsenen 35 Chapter 11 Minitrend V5 Display Assembly 37 Display Assembly Replacement usssssnssssssnsnsnssssnensssessnsnssssnsnsnsssensnsnsensnsnensensnenens 37 Chapter 12 Multitrend Plus V5 Analogue Card Installation 39 Removing the Rear Panel Inside the Unit Standard and Universal Analogue Cards nccoonononnonencinononcononononcnconononconononcaconononos 40 Removing the Analogue Card Inserting the Analogue Card Re assembling the Unit esessssssnsnsssessnsnsnssnsnensssensnensensnsnsnssnsnsnsnssnsnensessnsnsnsnssnsnensenen Chapter 13 Multitrend Plus V5 Alarm Card Installati
24. 800 BELGIUM HONEYWELL S A 3 Avenue de Bourget B 1140 BRUSSELS BELGIUM Tel 32 2 728 27 11 BRAZIL HONEYWELL DO BRA ZIL AND CIA Rua Jose Alves Da Chunha Lima 172 BUTANTA 05360 050 SAO PAULO SP BRAZIL Tel 55 11 819 3755 BULGARIA HONEYWELL EOOD 14 Iskarsko Chausse POB 79 BG 1592 Sofia BULGARIA Tel 359 791512 794027 792198 CANADA HONEYWELL LIMITED THE HONEYWELL CENTRE 529 Mc Nicoll Avenue M2H 2C9 NORTH YORK ONTARIO CANADA Tel 416 502 5200 CZECH REPUBLIC HONEYWELL Spol s r o Budejovicka 1 140 21 Prague 4 Czech Republic Tel 42 2 6112 3434 DENMARK HONEYWELL A S Automatikvej 1 DK 2860 Soeborg DENMARK Tel 45 39 55 56 58 FINLAND HONEYWELL OY Ruukintie 8 FIN 02320 ESPOO 32 FINLAND Tel 358 0 3480101 FRANCE HONEYWELL S A B timent le Mercury Parc Technologique de St Aubin Route de Orme CD 128 91190 SAINT AUBIN FRANCE Tel from France 01 60 19 80 00 From other countries 33 1 60 19 80 00 GERMANY HONEYWELL AG Kaiserleistrasse 39 D 63067 OFFENBACH GERMANY Tel 49 69 80 64444 HUNGARY HONEYWELL Kft Gogol u 13 H 1133 BUDAPEST HUNGARY Tel 36 1 451 43 00 ICELAND HONEYWELL Hataekni hf Armuli 26 PO Box 8336 128 reykjavik Iceland Tel 354 588 5000 ITALY HONEYWELL S p A Via P Gobetti 2 b 20063 Cernusco Sul Naviglio ITALY Tel 39 02 92146 1 MEXICO HONEYWELL S A DE CV AV CONSTITUYENTES 900 COL
25. A1 on the rear panel are primarily for the standard analogue card with slots B and B1 for the universal analogue card However either slot can be used for both types of analogue card Maximum of 32 channels of input Installation for either of the analogue cards in slot A A1 B or B1 positions follows the same procedure 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Removing ie Analogue Card If replacing any of the analogue cards first remove any cards as necessary from slots A A1 or slots B B1 positions This is done by locating the earthing screw on the left side of the dividing panel in the middle of the unit looking from the rear Slot A s earthing screw is at the top slot B is second from the top slot A1 is third and slot B1 is fourth from the top Remove and retain the screws and shakeproof washers using a short reach screw driver Grip the front of the card or by the connector and gently pull to release the card from its connection to the mother board at the front of the unit Inserting the Analogue Card Slide the new analogue card carefully back along the board guides until the fixing bracket on the left side of the analogue card is in line with the single fixing hole on the side of the dividing panel The analogue card will locate into a mating connector in the mother board at the front of the unit Ensure the card is pushed fully home and that no internal wiring is damaged as the analogue card is returned
26. Connect the earth lead from the power supply on to the new rear panel assembly FIGURE 19 2 Rear panel connections Mains filter loom Power supply Earth lead Main filter loom Earth lead Transmitter power supply card Re assembling the Unit 72 Replace the rear panel reposition the toothed washers and replace and tighten the four M4 x 8mm pozi pan head self tap screws at each corner of the rear panel 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Chapter 20 Multitrend Plus V5 Disk Drive Replacement Removing the Rear Panel A CAUTION OBSERVE ANTI STATIC PRECAUTIONS Refer to BS EN1000151 1992 Basic specification Protection of electrostatic sensitive devices Full anti static precautions MUST be observed when in contact with the electronics within the recorder Removal of PCBs and battery back up will result in the loss of all non volatile data Ensure all data and set ups are saved first Failure to comply with these instructions may result in product damage e To remove the rear panel of the recorder loosen and remove the four M4 x 8mm self tap screws at each corner of the rear panel taking care to retain the screws and shakeproof washer FIGURE 20 1 Removing the rear panel Removal of the rear panel is necessary for replacement or fitting any of the PC cards 43 TV 25 10 GLO Issue 2 11 00 UK 73 Honeywell Disk Drive Replacement Before the disk drive can be accessed it is
27. Honeywell Service Manual Minitrend Multitrend Plus Honeywell 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Table of Contents Table of Contents iii Chapter 1 Introduction 1 Chapter 2 Minitrend V5 Analogue Card Installation 3 Removing the Rear Panel esssssssnsnsssessnsnssssnsnsnssnsnsnsnsensnsnsnssnsnsnensensnensnssnsnennsensnsnses 3 INSTANCIA E TAO 4 Standard and Universal Analogue Cards usessssssnsnsessnsnsnssnsnsnsnssssnsnsnsensnsnenssnsnensene 4 Removing the Analogue Card esssssnsnsnsnsssnsnsnsnsnnsnsnnnsnsnsnnnsnsnnnsnsnsnsnsnsnsnsnsnsnsnsnensnsnene 4 Inserting the Analogue Card Re assembling the Unit essssssnsnsnsssnsnsnsnsssnsnsnsnnsnsnnnnnsnsnsnnnsnsnnnsnsnsnsnsnsnsnsnsnsnsnsnensnsnene Chapter 3 Minitrend V5 Alarm Card Installation 7 Removing the Rear Panel esssssssnsnsnsssnsnsssssnsnsnsensnnnensnsnsnsnsnsnsnsnsnsnsnsnsnsnsnsnensnsnsnsnsnsne 7 AAA eet ERE RR ERE ES EET eese vie ETEF 8 Alarm Cards 8 Removing the Alarm Card uessssssnensesensnsnssssnsnsnssnsnsnsnsensnsnsnssnsnsnsnssnsnenssssnsnensnsensnenses 8 Inserting the Alarm Card eese eee eese estet tata ttes tata ttn enean entes enun 9 Re assembling the Unit esessssssnsnsssessnsnsnssnsnsnssssnsnensensnsnenssnsnsnsnssnsnensensnsnsnnsensnensenen 10 Chapter 4 Minitrend V5 Power Supply Card amp Transmitter Power Supply Card Installation 11 Removing the Rear Panel esssssssnsnsssensnsssessnsnsnsensnensnsensnsnsnssnsnensensn
28. Installation 67 Removing the Rear Panel esssssssnsnsssensnsssessnsnsnssnsnensesensnsnsnssnsnsnsssensnensessnsnenssnsnenens 67 ITSR NCBI M 68 Iani wor M eet 69 Removing the PCMCIA Card cnoonononoononsacononencicononencocononeacononencncocononcorononercanononss 69 Inserting the PCMCIA Card esssnsnensnsnsnsssnsnsnsnsnsnssnsnsnsnsnsnsnsnsnsnsnsnsnsnsnsnsnsnsnsnsnsnsnnee 70 R assembling the Unit ini tee sin s Ea Sisa aya 70 Chapter 19 Multitrend Plus V5 Rear Panel Assembly 71 Removing the Rear Panel esssssssnsnsssensnsssessnsnsnsensnensesensnsnsnssnsnsnsnssnsnensensnsnnsensnsnnns 71 Replacing the Rear Panel Assembly 12 Re assembling the Unit esessssssnsnsssensnsnssssnsnsnsssensnensensnsnenssnsnensnsensnensessnsnensnssnsnensenen 72 Chapter 20 Multitrend Plus V5 Disk Drive Replacement 73 Removing the Rear Panel esssssssnsnsssensnsssessnsnsnsensnensesensnsnsnssnsnsnssssnsnensensnsnensensnennns 73 Disk Drive Replacement usessssssssnenssssnsnsssessnsnsnssnsnensssensnsnsnssnsnsnsnssnsnensessnsnenssnsnenens 74 Inside the Unit 74 Disk Drive Installation ueesesnscsnsnsnsnsnsnsnsnsssnsnsnsnsnnennnensnensnsnsnensnsnsnsnensnsnsnsnsnsnsnsnsnsnnne 75 Re assembling the Unit eusessssssssnsssensnsnssssnsnsnsssensnensensnsnsnssnsnsnsssensnsnsessnsnsnsssensnnsenen 75 Index 77 43 TV 25 10 GLO Issue 2 11 00 UK vii Honeywell viii 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Chapter 1 Introduction This manual is int
29. URE 13 1 Removing the rear panel 43 TV 25 10 GLO Issue 2 11 00 UK 43 Honeywell Inside the Unit DO NOT disconnect any wiring from the mains socket on the rear panel Gently move the rear panel to the side of the case to allow internal access 1 Analogue Card A 2 Analogue Card B 3 Analogue Card A1 NIS e 2 4 Analogue Card B1 5 Comms Card C 6 Processor Card C 7 PCMCIA Card D behind the alarm card 8 Alarm Card 9 Transmitter Power Supply Card 10 Mother Board 11 Power Supply 12 Disk Drive FIGURE 13 2 Position of the internal boards Alarm Cards 44 There are two main types of alarm cards the relay alarm card and the input output card For the Multitrend Plus V5 the relay alarm card is available with 4 or 8 channels of relay output the 8 channel having two channels of digital input as standard The input output cards for the Multitrend Plus V5 are available with 8 16 or 32 chan nels all channels may be used as digital inputs All alarm cards take up position primarily in slot D and an extra alarm card can be fitted in slot D1 shown on the rear panel of the Multitrend Plus V5 If the unit is fitted with a PCMCIA card in alarm slot D a snubber card will be required If the unit is fitted with a PCMCIA card in alarm slot D the snubber card is not required For a second alarm to be fitted
30. V 25 10 GLO Issue 2 11 00 UK R Rear Panel Assembly Minitrend V5 31 Rear Panel Assembly Multitrend Plus V5 71 Retransmission Card Minitrend V5 15 Retransmission Card Multitrend Plus V5 53 T Transmitter Power Supply Card Minitrend log ee essen 11 Val dl nee 49 77 Honeywell 78 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Please take a moment to complete this questionnaire How would you rate the reputation of Honeywell Tick as appropriate A very reputable successful company A reputable company A disreputable company No views either way 2 Service How do you rate or perceive the following service levels provided by our sales staff Tick as appropriate Excellent Good Fair Response speed Quality of response Follow up response Overall level of service How do you rate or perceive the following service levels provided by our Technical Support Ser vice Tick as appropriate Excellent Good Fair Response speed Quality of response Follow up response Overall level of service How could our service be improved upon How many times do you receive a visit from one of our Sales representatives Visits every 1 3 months 3 6 months 6 12 months How does that compare to our competitors More Less The
31. a 5 way socket mating half supplied pcb position J1 TXA 43 TV 25 10 GLO Issue 2 11 00 UK 61 Honeywell 62 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Chapter 17 Multitrend Plus V5 Processor Card Installation Removal of the rear panel ONLY is necessary when this operation is intended Removing the Rear Panel A CAUTION OBSERVE ANTI STATIC PRECAUTIONS Refer to BS EN1000151 1992 Basic specification Protection of electrostatic sensitive devices Full anti static precautions MUST be observed when in contact with the electronics within the recorder Removal of PCBs and battery back up will result in the loss of all non volatile data Ensure all data and set ups are saved first Failure to comply with these instructions may result in product damage e To remove the rear panel of the recorder loosen and remove the four M4 x 8mm self tap screws at each corner of the rear panel taking care to retain the screws and shakeproof washers FIGURE 17 1 Removing the rear panel 43 TV 25 10 GLO Issue 2 11 00 UK 63 Honeywell Inside the Unit DO NOT disconnect any wiring from the mains socket on the rear panel Gently move the rear panel to the side of the case to allow internal access 1 Analogue Card A 2 Analogue Card B 3 Analogue Card A1 4 Analogue Card B1 5 Comms Card C 6 Processor Card C 7 PCMCIA Card D behind the alarm
32. ailure to comply with these instructions may result in product damage e To remove the rear panel of the recorder loosen and remove the four No 6 x 18 self tap screws at each corner of the rear panel taking care to retain the screws and shakeproof washers FIGURE 7 1 Removing the rear panel e f fitted loosen and remove the mounting clamp screws M3 x 16mm pan pozi at the top and bottom of the extrusion to allow removal of the back panel NB Only one of the two screws may have to be removed while loosening the other will be sufficient 43 TV 25 10 GLO Issue 2 11 00 UK 23 Honeywell Inside the Unit DO NOT disconnect any wiring from the mains socket on the rear panel Gently move the rear panel to the side of the extrusion to allow internal access 1 Power Supply Card 2 Analogue Card A 3 Analogue Card B 4 Comms Card C 5 Processor Card 6 Alarm Card D 7 PCMCIA Card behind the alarm card 8 Disk Drive FIGURE 7 2 Position of the internal boards Processor Card The processor card is not an options card and is fitted in all units The processor card occupies slot C on the back of the unit Removing the Processor Card 24 If replacing a processor card remove any cards as necessary from the slot C posi tion This is done by locating the earthing screw on the left side of the unit looking from the rear Slot C s earthing screw is second from the bottom
33. can be fitted in slot D1 This is the first available position after the four analogue slots A A1 B 4 B at the top right of the unit e The alarm card for this slot comes with the alarm ribbon cable and an alarm interface card e Connect the two cards together with the ribbon cable and feed the alarm inter face card in to slot D1 using the board guides on the inside of the unit e Slide the alarm card in after the interface card using the same board guides The alarm interface card will locate into two FIGURE 13 5 Second alarm card connectors on the mother board at the with an alarm interface card front of the unit Ensure the card is pushed fully home e Align the alarm card with its fixing hole and earth bracket on the side of the case e Replace the earth screw and shakeproof washer on the side of the case torque to 120cNm Re assembling the Unit Remove the plastic blanking plate safety cover on the bottom of the rear panel by pushing out the push rivets if adding the alarm card as a new option card e Replace the rear panel reposition the shakeproof washers and replace and tighten the four M4 x 8mm pozi pan head screws at each corner of the rear panel 43 TV 25 10 GLO Issue 2 11 00 UK 47 Honeywell 48 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Chapter 14 Multitrend Plus V5 Power Supply Card amp Transmitter Power Supply Card Installation Removing the Rear Panel Removal of the rear
34. card 8 Alarm Card 9 Transmitter Power Supply Card 10 Mother Board 11 Power Supply 12 Disk Drive 64 AHA FAG BANANAS FIGURE 17 2 Position of the internal boards 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Processor Card The processor card is not an options card and is fitted in all units The processor card occupies slot C on the back of the unit Removing the Processor Card 43 TV 25 10 GLO If replacing a processor card remove any cards as necessary from the slot C posi tion This is done by locating the earthing screw on the left side of the dividing panel in the middle of the unit looking from the rear Slot C s earthing screw is second from the bottom Grip the card by its connector and gently pull to release the card from its connection to the mother board Pull the card out about half way then disconnect the two connectors on the proces sor card in order to release the card One is a small 40 way ribbon cable connector this is the display connector and the other is a 5 way connector which goes to the back light Disconnect both from the processor card and remove If there is an alarm card fitted in the slot below slot D there will be a 34 way con nector attached to the underside of the processor card this must be disconnected before the processor card can be removed If a comms card is fitted it will have to be removed The comms card plugs in on to
35. d back along the board guides of slot D The processor card will then locate along the board guides for slot C If an alarm card is fitted begin to slide it in after the PC card keeping the ribbon cable flat to the alarm card All the boards should slide in together with the processor card locating into a mating connector on the mother board at the front of the unit Insert the processor card fully until the fixing bracket on the left side of the proces sor card is in line with the single fixing hole on the side of the unit Line up the alarm card and replace the earthing screw in the same way Ensure the cards is pushed fully home and that no internal wiring is damaged as the cards are returned Replace the earth screw and toothed washer on the side of the extrusion torque to 120cNm or 10 62Ibf in Re assembling the Unit Replace the rear panel reposition the shakeproof washers and replace and tighten the four No 6 x self tap screws at each corner of the rear panel Replace and or tighten the mounting clamp screws at the top and bottom of the extrusion FIGURE 8 4 The Earthing Screw 43 TV 25 10 GLO Issue 2 11 00 UK 29 Honeywell 30 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Chapter 9 Minitrend V5 Rear Panel Assembly Removing the Rear Panel Removal of the rear panel is necessary for replacement or fitting any of the PC cards A CAUTION OBSERVE ANTI STATIC PRECAUTIONS Refer to BS EN1
36. ds The PCMCIA card know as the PC card is an extra memory card option which can be used as a hard drive The PC card is plugged into the processor card which occupies slot C The PC card goes into the area behind the alarm card if fitted in slot D Removing the PCMCIA Card 28 If replacing a PC card remove any cards as necessary e g an alarm card from the slot D position This is done by locating the earthing screw on the left side of the unit looking from the rear Slot D s earthing screw is at the bottom Remove and retain the screw and shakeproof washer If there is an alarm card in slot D it will be attached to the processor card via a 34 way ribbon cable connector this can be left connected It is necessary to remove the processor card in slot C at the same time This is done by locating and removing the earthing screw from slot C which is second from the bottom of the unit Grip the front of the processor card or by the connector and gently pull to release the card from its connection to the mother board 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell If there is a comms card fitted this will be a separate card plugged into the top of the processor card this is not affected FIGURE 8 3 PCMCIA card plugs in under the processor card Inserting the PCMCIA Card Plug in the PC card into the under side of the processor card and ensure all four headers are pushed fully home Begin to slide the PC car
37. ed Removing the Rear Panel A CAUTION OBSERVE ANTI STATIC PRECAUTIONS Refer to BS EN1000151 1992 Basic specification Protection of electrostatic sensitive devices Full anti static precautions MUST be observed when in contact with the electronics within the recorder Removal of PCBs and battery back up will result in the loss of all non volatile data Ensure all data and set ups are saved first Failure to comply with these instructions may result in product damage e To remove the rear panel of the recorder loosen and remove the four No 6 x self tap screws at each corner of the rear panel taking care to retain the screws and shakeproof washers FIGURE 8 1 Removing the rear panel e f fitted loosen and remove the mounting clamp screws M3 x 16mm pan pozi at the top and bottom of the extrusion to allow removal of the back panel NB Only one of the two screws may have to be removed while loosening the other will be sufficient 43 TV 25 10 GLO Issue 2 11 00 UK 27 Honeywell Inside the Unit DO NOT disconnect any wiring from the mains socket on the rear panel Gently move the rear panel to the side of the extrusion to allow internal access Power Supply Card Analogue Card A Analogue Card B Comms Card C Processor Card Alarm Card D PCMCIA Card behind the alarm card 8 Disk Drive PCMCIA Card FIGURE 8 2 Position of the internal boar
38. ended as a guide for the purposes of replacing or installing hardware Honeywell Recorders are designed for ease of assembly with minimal disturbance to the rest of the unit There are however very few user serviceable components removing the rear panel and opening the back of the recorder should only be performed under the following cir cumstances e When an item of hardware requires individual replacement e When an item of hardware is to be retrospectively fitted In all other instances it is recommended that the complete unit be returned for service to an authorised agent or service centre Before attempting to strip down a Honeywell recorder it is advisable to clear a suffi cient work space so components such as the front panel can be rested on the work sur face without getting scratched or damaged This document is divided into two halves with separate instructions for the Minitrend V5 and the Multitrend Plus V5 A CAUTION OBSERVE ANTI STATIC PRECAUTIONS Refer to BS EN1000151 1992 Basic specification Protection of electrostatic sensi tive devices Ensure all power to the recorder is disconnected before attempting all maintenance procedures Full anti static precautions MUST be observed when in contact with the electronics of your recorder Removal of PCBs and battery back up will result in the loss of all non volatile data Ensure all data and set ups are saved Upon completion of service procedures detailed in
39. formation If warranted goods are returned to Honeywell during that period of coverage Honeywell will repair or replace without charge those items it finds defective The foregoing is Buyers sole remedy and is in lieu of all other warranties expressed or implied including those of merchantability and fitness for a particular purpose While we provide application assistance personally through our literature and the Honeywell web site it is up to the customer to determine the suitability of the product in the application Specifications may change at any time without notice The infor mation we supply is believed to be accurate and reliable as of this Sales and Service Honeywell serves its customers through a worldwide network of sales offices and distributors For application assistance current specifications pricing or name of the nearest Authorised Distributor contact your local sales office or INTERNET www honeywell com sensing printing However we assume no responsibility for its use ARGENTINA HONEYWELL S A I C BELGRANO 1156 BUENOS AIRES ARGENTINA Tel 54 1 383 9290 ASIA PACIFIC HONEYWELL ASIA PACIFIC Inc Room 3213 3225 Sun Kung Kai Centre N 30 Harbour Road WANCHAI HONG KONG Tel 852 829 82 98 AUSTRALIA HONEYWELL LIMITED 5 Thomas Holt Drive North Ryde Sydney NSW AUSTRALIA 2113 Tel 61 2 353 7000 AUSTRIA HONEYWELL AUSTRIA G m b H Handelskai 388 A1020 VIENNA AUSTRIA Tel 48 1 727
40. h corner of the rear panel taking care to retain the screws and shakeproof washers FIGURE 4 1 Removing the rear panel e f fitted loosen and remove the mounting clamp screws M3 x 16mm pan pozi at the top and bottom of the extrusion to allow removal of the back panel NB Only one of the two screws may have to be removed while loosening the other will be sufficient 43 TV 25 10 GLO Issue 2 11 00 UK 11 Honeywell Inside the Unit DO NOT disconnect any wiring from the mains socket on the rear panel Gently move the rear panel to the side of the extrusion to allow internal access 1 Power Supply Card 2 Analogue Card A 3 Analogue Card B 4 Comms Card C 5 Processor Card 6 Alarm Card D 7 PCMCIA Card behind the alarm card 8 Disk Drive FIGURE 4 2 Position of the internal boards Power Supply and Transmitter Power Supply Cards The power supply card is available as 240 Vac 24 Vdc or 48 Vdc The installation for either of the power supply or the transmitter power supply cards in the top slot position follows the same procedure The transmitter power supply card requires the top right blanking plate on the rear panel to be removed to allow for connection Removing the Power Supply Card If replacing the power supply card remove the existing card by locating the earthing screw on the left side of the unit looking from the rear The top earthing screw is f
41. he earthing screw on the outside of the unit left side looking from the rear The bottom earthing screw is for the transmitter power supply card e Grip the front of the card and gently pull to release the card slide the power supply card out e Disconnect the 3 way mains filter loom and the earth lead from the mains filter on the rear panel e The card can now be removed fully from the unit 43 TV 25 10 GLO Issue 2 11 00 UK 51 Honeywell Inserting the Transmitter Power Supply Card Re assembling 52 The new transmitter power supply card will be supplied with an earth lead and the mains filter loom Connect the 3 way mains filter loom and the earth lead from the power supply card to the mains filter on the rear panel These connections will be fitted with piggy back spade terminals Slide the power supply card carefully into the case along the board guides for slot F The transmitter power supply card can now be fully inserted into the unit until the fixing bracket on the left side of the power supply card is in line with the single fixing hole on the side of the case Ensure the card is pushed fully home and that no internal wiring is damaged as the power supply card is returned Replace fit the earth screw and shakeproof washer on the side of the extrusion torque to 120cNm or 10 62Ibf in FIGURE 14 4 The Earthing Screws the Unit Remove the plastic blanking plate safety cover for the appropriate slot on
42. he left side of the processor card is in line with the single fixing hole on the side of the dividing panel e The processor card will locate into a mating connector in the mother board at the front of the unit e Ensure the card is pushed fully home and that no internal wiring is damaged as the alarm card is returned e Replace the earth screw and shakeproof washer on the side of the case torque to 120cNm or 10 62lbf in FIGURE 16 4 The Earthing Screws Re assembling the Unit e Remove the plastic blanking plate safety cover for the appropriate slot on the rear panel if necessary by pushing out the push rivets from behind e Replace the rear panel reposition the shakeproof washers and replace and tighten the four M4 x 8mm self tap screws at each corner of the rear panel 60 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Connection Details Ethernet Interface This is an 8 way RL45 socket Molex 95040 288 used for Ethernet connection pcb position J5 Standard Ethernet connection 7 TD 1 TD 2 a Cre d RD 3 SOO 4 4 8 59 7 5 locating pins O RD 6 not connected 5 O O 8 A B 2 RS232 Interface Comm2 This is a 9 way D type connector mating half not supplied pcb position P1 7 7 ren O 9 R12 O 4 DTR2 O 8 CTS2 o 3 TXD2 o 7 RTS2 O 2 RXD2 O 6 DSR2 OF 1 DCD2 RS485 Interface Comm3 Trendbus This is
43. he ribbon cable flat to the alarm card All the boards will slide in together with the processor card locating into a mating connector on the mother board at the front of the unit Insert the processor card fully until the fixing bracket on the left side of the proces sor card is in line with the single fixing hole on the side of the dividing panel in the middle of the unit Line up the alarm card and replace the earthing screw in the same way Ensure the card is pushed fully home and that no internal wiring is damaged as the alarm card is returned Replace the earth screw and toothed washer on the side of the case torque to 120cNm or 10 621bf in FIGURE 17 4 The Earthing Screws Re assembling the Unit Remove the plastic blanking plate safety cover for the appropriate slot on the rear panel if necessary by pushing out the push rivets from behind Replace the rear panel reposition the toothed washers and replace and tighten the four M4 x 8mm self tap screws at each corner of the rear panel 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Chapter 18 Multitrend Plus V5 PCMCIA Card Installation Removal of the rear panel ONLY is necessary when this operation is intended Removing the Rear Panel A CAUTION OBSERVE ANTI STATIC PRECAUTIONS Refer to BS EN1000151 1992 Basic specification Protection of electrostatic sensitive devices Full anti static precautions MUST be observed when in contact with the electron
44. her Grip the front of the card or by the connector and gently pull to release the card from its connection to the mother board Begin to slide the card out If an alarm card is also fitted a 34 way connector on the underside of the processor card will have to be disconnected in order to slide the processor card out further Pull out the processor card and turn it over to show the underside of the card Remove the two screws and shakeproof washers from the two pillars connecting the comms and processor cards together from the underside of the processor card Carefully separate the comms card from the processor card TIP Pull the cards apart evenly from each side There are three double row headers in different orientations resulting in quite a tight fit FIGURE 16 3 The comms card plugs in on top of the processor card do ASE gt 43 TV 25 10 GLO Issue 2 11 00 UK 59 Honeywell Inserting the Comms Cards e Plugin the new comms card to the processor card and replace the two screws and shakeproof washers on the underside of the processor card to secure the pillars locking the two cards together e Begin to slide the processor card carefully back into the extrusion If an alarm card is fitted keep the ribbon cable flat to the alarm card slide the processor card in and reconnect the ribbon cable to the connector on the underside of the processor card e nsert the processor card fully until the fixing bracket on t
45. holes and replace using the original Screws e Replace the processor card in slot C See Multitrend Plus V5 Processor Card Instal lation on page 63 e Replace any cards in slot D See Multitrend Plus V5 Disk Drive Replacement on page 73 and Multitrend Plus V5 PCMCIA Card Installation on page 67 FIGURE 20 3 The Earthing Screw Re assembling the Unit e Replace the rear panel reposition the shakeproof washers and replace and tighten the four M4 x 8mm pozi pan head self tap screws at each corner of the rear panel 43 TV 25 10 GLO Issue 2 11 00 UK 75 Honeywell 76 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Index A Alarm Card 2nd slot DI Multi Plus V5 47 Alarm Card Minitrend V 7 Alarm Card Multitrend Plus V5 43 Analogue Card Minitrend V 3 Analogue Card Multitrend Plus V5 39 C Communications Card Minitrend V5 19 Communications Card Multi Plus V5 57 D Disk Drive Minitrend V5 33 Disk Drive Multitrend Plus V5 73 Display Assembly MinitrendV3 37 P PCMCIA Card Minitrend V 27 PCMCIA Card Multitrend Plus V5 67 Power Supply Card Minitrend V5 11 Power Supply Card Multitrend Plus V5 49 Processor Card Minitrend V 23 Processor Card Multitrend Plus V5 63 43 T
46. ics within the recorder Removal of PCBs and battery back up will result in the loss of all non volatile data Ensure all data and set ups are saved first Failure to comply with these instructions may result in product damage e To remove the rear panel of the recorder loosen and remove the four M4 x 8mm self tap screws at each corner of the rear panel taking care to retain the screws and shakeproof washers FIGURE 18 1 Removing the rear panel 43 TV 25 10 GLO Issue 2 11 00 UK 67 Honeywell Inside the Unit DO NOT disconnect any wiring from the mains socket on the rear panel Gently move the rear panel to the side of the case to allow internal access 1 Analogue Card A 2 Analogue Card B 3 Analogue Card A1 4 Analogue Card B1 ei 1 5 Comms Card C b 181113 6 Processor Card C 7 PCMCIA Card D behind the alarm card 8 Alarm Card 9 Transmitter Power Supply Card 10 Mother Board 11 Power Supply 12 Disk Drive FIGURE 18 2 Position of the internal boards 68 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell PCMCIA Card The PCMCIA card know as the PC card is an extra memory card option which can be used as a hard drive The PC card is plugged into the processor card which occupies slot C The PC card goes into the area behind the alarm card if fitted in slot D Removing me PCMCIA Card If
47. ine with the single fixing hole on the side of the case The retransmission card will locate into a mating connector in the mother board at the front of the unit Ensure the card is pushed fully home and that no internal wiring is damaged as the retransmission card is returned Replace fit the earth screw and shakeproof washer on the side of the case torque to 120cNm or 10 62Ibf in FIGURE 15 3 The Earthing Screws the Unit Remove the plastic blanking plate safety cover for the appropriate slot on the rear panel if necessary by pushing out the push rivets from behind Replace the rear panel reposition the toothed washers and replace and tighten the four M4 x 8mm self tap screws at each corner of the rear panel 11 00 UK 55 Honeywell 56 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Chapter 16 Multitrend Plus V5 Communications Card Installation Removal of the rear panel ONLY is necessary when this operation is intended A CAUTION OBSERVE ANTI STATIC PRECAUTIONS Refer to BS EN1000151 1992 Basic specification Protection of electrostatic sensitive devices Full anti static precautions MUST be observed when in contact with the electronics within the recorder Removal of PCBs and battery back up will result in the loss of all non volatile data Ensure all data and set ups are saved first Failure to comply with these instructions may result in product damage Removing the Rear Panel e To
48. initrend V5 Alarm Card Installation Removal of the rear panel ONLY is necessary when this operation is intended Removing the Rear Panel A CAUTION OBSERVE ANTI STATIC PRECAUTIONS Refer to BS EN1000151 1992 Basic specification Protection of electrostatic sensitive devices Full anti static precautions MUST be observed when in contact with the electronics within the recorder Removal of PCBs and battery back up will result in the loss of all non volatile data Ensure all data and set ups are saved first Failure to comply with these instructions may result in product damage e To remove the rear panel of the recorder loosen and remove the four No 6 x self tap screws at each corner of the rear panel taking care to retain both the shake proof washer and the screw FIGURE 3 1 Removing the rear panel e f fitted loosen and remove the mounting clamp screws M3 x 16mm pan pozi at the top and bottom of the extrusion to allow removal of the back panel NB Only one of the two screws may have to be removed while loosening the other will be sufficient 43 TV 25 10 GLO Issue 2 11 00 UK 7 Honeywell Inside the Unit DO NOT disconnect any wiring from the mains socket on the rear panel Gently move the rear panel to the side of the extrusion to allow internal access 1 Power Supply Card 2 Analogue Card A 3 Analogue Card B Comms Card C gt Processor Card Alarm Card D
49. ly card on to the new rear panel assem bly Re ISSO the Unit 32 Remove any plastic blanking plate safety covers for the appropriate slots on the rear panel if necessary by pushing out the push rivets from behind Replace the rear panel reposition the toothed washers and replace and tighten the four No6 x 7 self tap screws at each corner of the rear panel Replace and or tighten the mounting clamp screws at the top and bottom of the extrusion 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Chapter 10 Minitrend V5 Disk Drive Replacement Removal of the rear panel ONLY is necessary when this operation is intended Removing the Rear Panel A CAUTION OBSERVE ANTI STATIC PRECAUTIONS Refer to BS EN1000151 1992 Basic specification Protection of electrostatic sensitive devices Full anti static precautions MUST be observed when in contact with the electronics within the recorder Removal of PCBs and battery back up will result in the loss of all non volatile data Ensure all data and set ups are saved first Failure to comply with these instructions may result in product damage e To remove the rear panel of the recorder loosen and remove the four No 6 x self tap screws at each corner of the rear panel taking care to retain the screws and shakeproof washers FIGURE 10 1 Removing the rear panel e f fitted loosen and remove the mounting clamp screws M3 x 16mm pan pozi at the top and bottom
50. necessary to remove any card from slots C and D Slot C is occupied by the processor card and possibly a comms card For removal of these cards see Multitrend Plus V5 Processor Card Installation on page 63 Remove any cards from slot D these may be an alarm card and or a PCMCIA memory card See Multitrend Plus V5 Disk Drive Replacement on page 73 and Multitrend Plus V5 PCMCIA Card Installation on page 67 Inside the Unit DO NOT disconnect any wiring from the mains socket on the rear panel Gently move the rear panel to the side of the case to allow internal access 1 Analogue Card A 2 Analogue Card B 3 Analogue Card A1 4 Analogue Card B1 eee eee es ALLELE 5 Comms Card C h l i 6 Processor Card C 7 PCMCIA Card D behind the alarm card 8 Alarm Card 9 Transmitter Power Supply Card 10 Mother Board 11 Power Supply 12 Disk Drive FIGURE 20 2 Position of the internal boards 74 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Disk Drive Installation e After all the cards have been removed from slots C and D unscrew the four fixing screws from the underside of the unit The four screws are recessed into dimples remove and retain the screws e Disconnect the two connectors on the end of the disk drive and re connect to the new disk drive e Position the new disk drive over the mounting
51. nsensnsnssssnsnsnssssnsnenesssnsnsnssnsnsnenee Re assembling the Unit essssnsnssssnsnsnssnsnsnsnsensnsnsnsensnsnensensnsnssssnsnsnssssnsnenssssnsnsnsensnsnenee 21 Connection Detalls eones in 22 Ethernet Interface comme 22 RS232 Interface Comm2 seseesorsnesnesnennesnesnesnesnnsnsensensensensennennennennssnsssssnssnnsnnennsnunne 22 RS485 Interface Comm3 Trendbus _seessossonsossnssnssnnsnsssnssnssnsnnssnssnssnssnnsnnsnnsnnsnnsnnnne 22 Chapter 7 Minitrend V5 Processor Card Installation 23 Removing the Rear Panel ssssssnsnssssnsnsnssssnsnsssensnsnensensnsnssssnsnsnssssnsnenessnsnsnsensnsnenee 23 Inside the Unit Processor Card Removing the Processor Card sssssensnsnssssnsnsnsessnsnensensnsnssssnsnsnssssnsnenssssnsnsnsensnsnenee 24 Inserting the Processor Card essssnsnssssnsnsnsessnsnsnsensnsnensensnsnssssnsnsnssssnsnensssnsnsnsensnsnenen 25 Re assembling the Unit Chapter 8 Minitrend V5 PCMCIA Card Installation 27 Removing the Rear Panel eessssnsssnsssnsnsssssnssssnensnessnsnnnsnenensnsnsnensnsnensnsnsnsnsnsnsnsnsnsne 27 Inside the Unit PCMCIA Card Removing the PCMCIA Card cnocononononononcinonencnnocononcnnonononnanononcncocononcononononcanonononos 28 Inserting the PCMCIA Card essssnsnssnsnsnsnssssnensnsensnsnensensnsnssssnsnsnssssnsnenesssnsnsnssnsnsnenee 29 Re assembling the Unit essssnsnsessnsnsnssssnsnsnsensnsnsnsensnsnensensnsnssssnsnsnsessnsnenssssnsnsnssnsnsnenee 29 iv 43 TV 25 10 GLO Issue 2 1
52. of the extrusion to allow removal of the back panel NB Only one of the two screws may have to be removed while loosening the other will be sufficient 43 TV 25 10 GLO Issue 2 11 00 UK 33 Honeywell Inside the Unit DO NOT disconnect any wiring from the mains socket on the rear panel Gently move the rear panel to the side of the extrusion to allow internal access 1 Power Supply Card 2 Analogue Card A 3 Analogue Card B 4 Comms Card C 5 Processor Card 6 Alarm Card D 7 PCMCIA Card behind the alarm card 8 Disk Drive FIGURE 10 2 Position of the internal boards Disk Drive Replacement Before the disk drive can be accessed it is necessary to remove all the cards from the unit The top card is the power supply card this is attached to the rear panel and can be removed and replaced See Minitrend V5 Power Supply Card amp Transmitter Power Supply Card Installation on page 11 Slots A and B are for the analogue cards standard or universal these can be removed and replaced following the instructions on Minitrend V5 Analogue Card Installation on page 3 Slot C is occupied by the processor card and possibly a comms card For removal and replacement of these cards see Minitrend V5 Processor Card Installation on page 23 See also Minitrend V5 Communications Card Installation on page 19 Remove any cards from slot D these may be an alarm card and or
53. om the top and slot B s earthing screw is third from the top Remove and retain the screws and washers e Grip the front of the card or by the connector and gently pull to release the card from its connection to the mother board at the front of the unit 4 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Inserting the Analogue Card e Slide the new analogue card carefully back along the extrusion until the earth fixing bracket on the left side of the analogue card is in line with the single fixing hole on the side of the extrusion e The analogue card will locate into a mating connector in the mother board at the front of the unit e Ensure the card is pushed fully home and that no internal wiring is damaged as the analogue card is returned e Replace fit the earth screw and shakeproof washer on the side of the extrusion torque to 120cNm or 10 62Ibf in Re assembling the Unit e Remove the plastic blanking plate safety cover for the appropriate slot on the rear panel if necessary by pushing out the push rivets from behind e Replace the rear panel reposition the shake proof washers and replace and tighten the four No 6 x self tap screws at each corner of the rear panel e Replace and or tighten the mounting clamp screws at the top and bottom of the extrusion FIGURE 2 3 The Earthing Screws 43 TV 25 10 GLO Issue 2 11 00 UK 5 Honeywell 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Chapter 3 M
54. on 43 Removing the Rear Panel esssssssnsnssssnsnsssessnsnsnsensnensesensnsnsnssnsnsnsessnsnensensnsnensensnsnnns 43 Inside the Unit eec uE ASCO 44 PEE Mc 44 Removing the Primary Alarm Card in slot D omcoconononnonencnnononononcononeoconononcanononoss 45 Inserting the Primary Alarm Card in slot D essssnsnsssensnsnsassnsnsnnsensnensensnsnensensnennns 45 Inserting a Second Alarm Card in slot DI oncnonenoconononnonenconononononcononeorocononcaononoss 47 Re assembling the Unit esesssssssnsssensnsnssssnsnsnssssnsnensensnsnsnssnsnsnsnssnsnensessnsnsnsnssnsnensenen 47 43 TV 25 10 GLO Issue 2 11 00 UK v Honeywell Chapter 14 Multitrend Plus V5 Power Supply Card amp Transmitter Power Supply Card Installation 49 Removing the Rear Panel uessssssnsnssssnsnsnssssnensesensnsnensensnsnssssnsnsnssssnsnensessnsnsnsensnsnenee 49 Inside the Unit ec 50 Power Supply and Transmitter Power Supply Card 4 50 Installing the Power Supply zrensnsnsessnsnsnsensnsnsssensnensssensnsnssnsnsnenssssnsnsnsessnsnenssssnsnsnsene 51 Removing the Transmitter Power Supply Card sese 51 Inserting the Transmitter Power Supply Card esee 52 Re assembling the Unit essssnsnssssnsnsnsssensnsnssnsnsnsnsensnsnensensnsnssnsnsnsnssssnsnenssssnsnsnssnsnsnenee 52 Chapter 15 Multitrend Plus V5 Retransmission Card Installation 53 Removing the Rear Panel uesssssnsnssssnsnsnsessnsnsnsensn
55. or the power supply card Grip the front of the card and gently pull to release the card from its connection to the mother board at the front of the unit Slide the power supply card out about 30mm Disconnect the 2 way disk drive loom on the left side of the card one red and one black wire From the piggy back board mounted on the power supply card disconnect the 3 way mains loom going to the live and neutral connections only two wires blue and brown Finally disconnect the earth lead from the mains filter on the rear panel green yel low wire The card can now be removed from the unit See Figure 4 3 on page 13 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell FIGURE 4 3 Power supply card Inserting the Pone Supply Card Slide the power supply card carefully along the extrusion leaving about 30mm of card protruding from the unit Reconnect 2 way disk drive loom to the power supply card and the 3 way mains filter loom form the rear panel to the live neutral connec tion on the power supply card The new power supply card will be supplied with an earth lead to be connected to the mains filter on the rear panel The power supply card can now be fully inserted into the unit until the earth fixing bracket on the left side of the power supply card is in line with the single fixing hole on the side of the extrusion The power supply card will locate into a mating connec tor on the mother board at the front of the unit
56. p of the processor card To do this pull the cards out of the unit and turn them over to show the underside of the processor card Remove the two screws and shakeproof washers from the two pillars connecting the two cards together from the underside of the processor card Carefully separate the comms card from the processor card Pull the two boards apart rotating them 90 each time There are three double row headers in different orientations therefore pulling from alternate side will ease the process FIGURE 17 3 Processor card Red wire this side Backlight connector on processor card MITT Display connector on M E i processor card Issue 2 11 00 UK 65 Honeywell Inserting the Processor Card 66 Plug in the PCMCIA card if fitted into the under side of the processor card and ensure all four headers are pushed fully home Plug in the comms card if fitted to the processor card and replace the two screws and shakeproof washers on the underside of the processor card to secure the pil lars locking the two cards together Begin to slide the PC card back along the board guides of slot D The processor card will then locate along the board guides for slot C When the processor card is half way in reconnect the ribbon cable display connec tor and the 5 way connector for the backlight If an alarm card is fitted connect via the 34 way alarm ribbon cable and begin to slide it in along the board guides keeping t
57. panel ONLY is necessary when this operation is intended A CAUTION OBSERVE ANTI STATIC PRECAUTIONS Refer to BS EN1000151 1992 Basic specification Protection of electrostatic sensitive devices Full anti static precautions MUST be observed when in contact with the electronics within the recorder Removal of PCBs and battery back up will result in the loss of all non volatile data Ensure all data and set ups are saved first Failure to comply with these instructions may result in product damage e To remove the rear panel of the recorder loosen and remove the four M4 x 8mm self tap screws at each corner of the rear panel taking care to retain the screws and shakeproof washers FIGURE 14 1 Removing the rear panel 43 TV 25 10 GLO Issue 2 11 00 UK 49 Honeywell Inside the Unit DO NOT disconnect any wiring from the mains socket on the rear panel Gently move the rear panel to the side of the extrusion to allow internal access 1 Analogue Card A 2 Analogue Card B 3 Analogue Card A1 4 Analogue Card B1 EMMA EXAMINAN 5 Comms Card C u E M v i 6 Processor Card C 7 PCMCIA Card D behind the alarm card 8 Alarm Card 9 Transmitter Power Supply Card 10 Mother Board 11 Power Supply 12 Disk Drive FIGURE 14 2 Position of the internal boards Power Supply and Transmitter Power Supply Card The power su
58. pply is available as 240 Vac 24 Vdc or 48 Vdc The power supply for either ac or dc units is screwed to the inside of the left panel as you look from the back of the unit Transmitter power supply card is only available on ac units The transmitter power supply card requires the bottom left blanking plate slot F on the rear panel to be removed to allow for connection 50 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Installing ne Power Supply If replacing a the power supply remove the 3 way mains loom from the power sup ply that goes to the mains filter on the rear panel e Next remove the earth lead from the mains filter on the rear panel The new power supply will come with a new earth lead fitted e Also disconnect a 6 way connector at the rear of the power supply this is the dc power to the mother board e Locate the 4 screws on the outside of the unit on the left in the middle looking from the rear Remove and retain screws and shakeproof washers FIGURE 14 3 Power supply and Transmitter power supply card Power supply Transmitter power supply card e Fit the new power supply and reconnect the 6 way connector at the rear of the power supply e Reconnect the 3 way mains loom and the earth lead at the front of the power sup ply from the mains filter on the rear panel Removing the Transmitter Power Supply Card e If replacing a the transmitter power supply card remove the existing card by locat ing t
59. replacing a PC card remove any cards as necessary from the slot D position This is done by locating the earthing screw on the left side of the dividing panel in the middle of the unit looking from the rear Slot D s earthing screw is at the bot tom e If there is an alarm card in slot D it will be attached to the processor card via a 34 way ribbon cable connector this can be left connected e tis necessary to remove the processor card in slot C This is done by locating and removing the earthing screw from slot C which is second from the bottom of the dividing panel in the middle of the unit e There are two connectors on the processor card which need to be disconnected in order to release the card One is a small 40 way ribbon cable connector which goes to the display and the other is a 5 way connector which goes to the back light Dis connect both from the processor card and remove e Grip the processor card by its connector and gently pull to release the card from its connection to the mother board e f there is a comms card fitted this will be a separate card plugged into the top of the processor card this is not affected FIGURE 18 3 PCMCIA card plugs in underneath the processor card 43 TV 25 10 GLO Issue 2 11 00 UK 69 Honeywell Inserting the HE Card Plug in the PC card into the under side of the processor card and ensure all four headers are pushed fully home Begin to slide the PC card back along
60. rew head FIGURE 5 1 Removing the rear panel e f fitted loosen and remove the mounting clamp screws M3 x 16mm pan pozi at the top and bottom of the extrusion to allow removal of the back panel NB Only one of the two screws may have to be removed while loosening the other will be sufficient 43 TV 25 10 GLO Issue 2 11 00 UK 15 Honeywell Inside the Unit DO NOT disconnect any wiring from the mains socket on the rear panel Gently move the rear panel to the side of the extrusion to allow internal access Power Supply Card Analogue Card A Analogue Card B Comms Card C Processor Card Alarm Card D PCMCIA Card behind the alarm card 8 Disk Drive FIGURE 5 2 Position of the internal boards Retransmission Card There are two types of retransmission cards one has two channels of retransmission and the other has 4 channels The retransmission card usually fits into slot B on the rear panel with an analogue card in slot A however either or both analogue slots can be used for retransmission Removing the Retransmission Card If replacing a retransmission card remove any cards as necessary from either slot A or slot B positions slot B is preferred This is done simply by locating the earthing screw on the left side of the unit looking from the rear Slot A s earthing screw is second from the top and slot B s earthing screw is third from the top Grip
61. ront surround complete with keypad and encoder assembly and the 5 5 LCD display This is the whole front section of the unit which hinges open to reveal the disk drive A CAUTION OBSERVE ANTI STATIC PRECAUTIONS Refer to BS EN1000151 1992 Basic specification Protection of electrostatic sensitive devices Full anti static precautions MUST be observed when in contact with the electronics within the recorder Removal of PCBs and battery back up will result in the loss of all non volatile data Ensure all data and set ups are saved first Failure to comply with these instructions may result in product damage e To remove the display assembly carefully lift the corner hinges outwards one by one to free the hinge pins and release the display e Unplug the cable from the well at the front of the main unit e Attach the new display assembly to the corner hinges and reconnect the cable Ensure the cable is connected correctly NB Should the display not work first check the connector has been plugged in accurately FIGURE 11 1 Display assembly 43 TV 25 10 GLO Issue 2 11 00 UK 37 Honeywell 38 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Chapter 12 Multitrend Plus V5 Analogue Card Installation Removal of the rear panel ONLY is necessary when this operation is intended Removing the Rear Panel A CAUTION OBSERVE ANTI STATIC PRECAUTIONS Refer to BS EN1000151 1992 Basic specification Pro
62. s locking the two cards together Begin to slide the processor card carefully back into the extrusion If an alarm card is fitted ensure the ribbon cable is kept flat to the alarm card Slide the processor card in and reconnect the ribbon cable to the connector on the underside of the processor card Insert the processor card fully until the earth fixing bracket on the left side of the processor card is in line with the single fixing hole on the side of the extrusion The processor card will locate into a mating connector on the mother board at the front of the unit Ensure the card is pushed fully home and that no internal wiring is damaged as the alarm card is returned Replace fit the earth screw and shakeproof washer on the side of the extrusion torque to 120cNm or 10 62Ibf in the Unit Remove the plastic blanking plate safety cover for the appropriate slot on the rear panel if necessary by push ing out the push rivets from behind Replace the rear panel reposition the shakeproof washers and replace and tighten the four No 6 x Y self tap screws at each corner of the rear panel Replace and or tighten the mounting clamp screws at the top and bottom of the extrusion FIGURE 7 4 The Earthing Screw 11 00 UK 25 Honeywell 26 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Chapter 8 Minitrend V5 PCMCIA Card Installation Removal of the rear panel ONLY is necessary when this operation is intend
63. snensensnsnensensnennns 11 Inside the Unit csscviscssascosscscbasedcsascecssstedocusvdensonsteusedecosabeshtevsdedevscceatevoeedcoentecnentneseosee 12 Power Supply and Transmitter Power Supply Cards 2 12 Removing the Power Supply Card zssssnssssssnsnsnssssnensesensnsnssssnsnsnsnssnsnensensnsnensensnsnnns 12 Inserting the Power Supply Card ussssssnssssssnsnsnssnsnensesensnsnsnssnsnsnssssnsnensensnsnensensnennns 13 Re assembling the Unit esessssssnsnsssessnsnsnssnsnsnsensnsnensensnsnsnssnsnsnnnssssnensessnsnsnnssnsnensenen 13 43 TV 25 10 GLO Issue 2 11 00 UK iii Honeywell Chapter 5 Minitrend V5 Retransmission Card Installation 15 Removing the Rear Panel Inside the Unit n Retransmission Card AAA A a cagla dal Ue uon oua se Eee EEG Removing the Retransmission Card essssssnensasessnsnensensnsnssssnsnsnssssnsnensnssnsnsnsensnsnenee 16 Inserting the Retransmission Card Re assembling the Unit smerenie t eiss Chapter 6 Minitrend V5 Communications Card Installation 19 Removing the Rear Panel ussssssnsnssssnsnsnssssnsnsssensnsnensensnsnssssnsnsnssssnsnensessnsnsnsensnsnenee Inside the Unit sesseccccscdsccsceccoonssvesnsonsesesedectessunctcnuosssnetasesorosescvayseeseeactenticonaeseosttecoeote Communications and RS485 Cards Removing the Comms Cards nmeoconononnonononcononenconocononcnnonononcanononcorocononcnronononcanonononos Inserting the Comms Cards ussssssnsnsssensnsnssssnsnsnsensnsne
64. snensensnsnssssnsnsnssssnsnensssnsnsnsensnsnenee 53 Inside the Unit ARR 54 Retransmission Card 54 Removing the Retransmission Card ssssssnensesessnsnensensnsnssssnsnsnssssnsnenssssnsnsnsensnsnenee 55 Inserting the Retransmission Card eessssssnsnsnsessnensssensnsnssssnsnsnssssnsnsnssssnsnenssnsnsnsnsene 55 Re assembling the Unit Chapter 16 Multitrend Plus V5 Communications Card Installation 57 Removing the Rear Panel Inside the Witt asserere TNA Communications and RS485 Cards csessoesoesnesneoneoneoneonsensensennrsnssnssnssnsensnnsensensensenne 59 Removing the Comms Cards Inserting the Comms Cards Re assembling the Unit Connection Details Ethernet Interface eese oe RS232 Interface Comm2 61 RS485 Interface Comm3 Trendbus _ssussesosnssnenusnssnsnssnsnssnsnnsnssnsnsnssnnsnsnnsnssnsnsnsnnnen 61 Chapter 17 Multitrend Plus V5 Processor Card Installation 63 Removing the Rear Panel usssssnsnssssnsnsnssssnsnsnsensnsnensensnsnssssnsnsnssssnsnensessnsnsnsensnsnenee 63 Insideithe Unit oido 64 Processor Card sssmmeym samsara 65 Removing the Processor Card sssssensnsnssssnsnsasensnsnensensnsnssssnsnsnssssnsnenssssnsnsnssnsnsnenee 65 Inserting the Processor Card essssnsnssssnsnsnssssnsnsnsensnsnensensnsnssssnsnsnssnsnsnenssssnsnsnsensnsnenee 66 vi 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Chapter 18 Multitrend Plus V5 PCMCIA Card
65. ssue 2 11 00 UK 9 Honeywell Re assembling Replace fit the earth screws and shakeproof washers on the side of the extrusion to secure both cards Torque to 120cNm or 10 62Ibf in FIGURE 3 5 The Earthing Screws the Unit Remove the plastic blanking plate safety cover on the bottom of the rear panel by pushing out the push rivets if adding the alarm card as a new option card Replace the rear panel reposition the shakeproof washers and replace and tighten the four No 6 x Y self tap screws at each corner of the rear panel Replace and or tighten the mounting clamp screws at the top and bottom of the extrusion 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Chapter 4 Minitrend V5 Power Supply Card amp Transmitter Power Supply Card Installation Removal of the rear panel ONLY is necessary when this operation is intended Removing the Rear Panel A CAUTION OBSERVE ANTI STATIC PRECAUTIONS Refer to BS EN1000151 1992 Basic specification Protection of electrostatic sensitive devices Full anti static precautions MUST be observed when in contact with the electronics within the recorder Removal of PCBs and battery back up will result in the loss of all non volatile data Ensure all data and set ups are saved first Failure to comply with these instructions may result in product damage e To remove the rear panel of the recorder loosen and remove the four No 6 x self tap screws at eac
66. tection of electrostatic sensitive devices Full anti static precautions MUST be observed when in contact with the electronics within the recorder Removal of PCBs and battery back up will result in the loss of all non volatile data Ensure all data and set ups are saved first Failure to comply with these instructions may result in product damage e To remove the rear panel of the recorder loosen and remove the four M4 x 8mm self tap screws at each corner of the rear panel taking care to retain the screws and shakeproof washers FIGURE 12 1 Removing the rear panel 43 TV 25 10 GLO Issue 2 11 00 UK 39 Honeywell Inside the Unit DO NOT disconnect any wiring from the mains socket on the rear panel Gently move the rear panel to the side of the extrusion to allow internal access Analogue Card A 2 Analogue Card B 3 Analogue Card A1 4 Analogue Card B1 5 Comms Card C 6 Processor Card C 7 PCMCIA Card D behind the alarm card 8 Alarm Card 9 Transmitter Power Supply Card 10 Mother Board 11 Power Supply 12 Disk Drive a Y LJ LS LL SS mA EIA FIGURE 12 2 Position of the internal boards Standard and Universal Analogue Cards The mechanical constraints for the standard analogue card and the universal analogue 40 card are the same The Multitrend Plus V5 has four positions for analogue input cards Slots A and
67. the front of the card or by the connector and gently pull to release card from its connection to the mother board at the front of the unit Inserting the Retransmission Card Slide the retransmission card carefully back along the extrusion until the earth fix ing bracket on the left side of the retransmission card is in line with the single fixing hole on the side of the extrusion The retransmission card will locate into a mating connector in the mother board at the front of the unit 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Re assembling 43 TV 25 10 GLO Issue 2 Ensure the card is pushed fully home and that no internal wiring is damaged as the retransmission card is returned Replace fit the earth screw and shakeproof washer on the side of the extrusion torque to 120cNm or 10 62Ibf in the Unit Remove the plastic blanking plate safety cover for the appropriate slot on the rear panel if necessary by pushing out the push rivets from behind Replace the rear panel reposition the shakeproof washers and replace and tighten the four No 6 x Y self tap screws at each corner of the rear panel Replace and or tighten the mounting clamp screws at the top and bottom of the extrusion 11 00 UK FIGURE 5 3 The Earthing Screw Honeywell 43 TV 25 10 GLO Issue 2 11 00 UK Honeywell Chapter 6 Minitrend V5 Communications Card Installation Removal of the rear panel ONLY is necessary when
68. tion of the internal boards Communications and RS485 Cards The mechanical constraints for the communications card and the RS485 comms card are the same The comms cards plugs in on top of the processor card like a piggy back board which occupies slot C Removing the Comms Cards 20 If replacing a comms card it is necessary to partially slide out the processor card to unplug the comms card This is done simply by locating the earthing screw on the left side of the unit looking from the rear Slot C earthing screw is second from the bottom remove and retain screw and shakeproof washer Grip the front of the processor card or by the connector and gently pull to release the card from its connection to the mother board Begin to slide the card out If an alarm card is also fitted a 34 way connector on the underside of the processor card will have to be disconnected in order to slide the processor card out further Pull out the processor card with the comms card attached and turn it over to show the underside of the processor card Remove the two screws and shakeproof wash ers from the two pillars connecting the two cards together from the underside of the processor card Carefully separate the comms card from the processor card TIP Pull the cards apart evenly from each side There are three double row headers in different orien tations resulting in quite a tight fit See Figure 6 3 on page 21 43 TV 25 10 GLO Issue 2 11 0

Honeywell Minitrend V5 Service Manual

Contents

Download Pdf Manuals

Related Search

Related Contents