DAP-04 Installation Manual
Contents
1. MW DAP 04 Installation Manual eat o JO YYYY CE Features Universal AC input Full range up to 305V Convert DALI signal to PWM signal 4 DALI addressable output channels Built in push dim function Comply with DALI standards IEC62386 101 102 207 Linear or logarithm dimming curve selectable meet IEC62382 207 PWM active high or active low selectable by jumper Dimming range 1 100 Fully isolated plastic case IP20 design 3 years warranty Class II power unit no FG Power consumption lt 0 5W Built in relay for ON OFF control of MEAN WELL s AC DC LED power supply Wiring Use wires with an adequate cross section see 3 Use suitable mounting tools to do the wiring and mounting see 3 Use a Miniature Circuit Breaker MCB with an adequate current rating to protect the lighting system see 4 Environmental limitations Maximum ambient temperature must not exceed 60 C Only install the unit at indoor environments Cautions This unit must be installed by a qualified electrician Only can be used with MEANWELL s LED Power Supply Units PSUs equipped with 3 in 1 dimming function LED PSUs made by other manufacturers may be incompatible with the DAP 04 Settings and connections 1 Terminal Block Pin Assignments O O facie DIMT E 0 o s2. Upto 20 unts LEDpower ssreeeeees LEDpower es LEDpower ssteseeeees LED power DIM DIM DIM DIM DIM DIM DIM DIM A F Dimi ome s i l DAP 04 Dm3 d P img Up t04 channels The DAP 04 is equipped with 4 DALI channels each channel can drive up to 20 LED PSUs allowing a total of 80 LED PSUs to be connected to the DALI PWM converter Each channel is individually addressable light intensity of LED PSUs connected to the same channel will be the same the maximum allowable voltage drop between the DAP 04 and LED PSUs should not be higher than 0 5V Maximum cable length for 1 31mm cables is 300m XNote Light intensity of LEDs in the same group may be decreased when one of the LED PSUs is AC OFF 3 Recommended Screwdriver Wire and Torque Setting Type The cover the blue ones TB1 ACL N PUSH DALI RY TB2 DIM1 2 3 4 Solid wire 1 02mm 1 628mm 1 02mm 1 29mm Stranded wire 0 823 2 08mm 0 823 1 31mm American wire gauge 14 18AWG 16 18AWG Wire stripping length 10mm 0 39 10mm 0 39 Screwdriver 5mm Phillips 3mm Slotted 3mm Slotted Recommended tightening torque 4 6kgf cm 4lb in Suggested push down strength 3 4kp 6 61 8 81lb 3 4kp 6 61 8 81Ib 4 Suggested Maximum Number of the DAP 04 Units that can be Connected to a MCB at 230Vac Model B10 B16 C10 C16 DAP 04 10 16 17 27 3xNote These calculated values are based on
3. MCB S201 series manufactured by ABB MEAN WELLENTERPRISES CO LTD Version 0 No 28 Wuquan 3rd Rd Wugu Dist New Taipei City 248 Taiwan R O C http www meanwell com
4. en bat oo alle Tez Bwe ES O DA TB4 Dm3 CO o O DA DiM4 OO o O RY Dm4 OO o LRY fog 2 Connection of Dimming Functions a DALI MEAN WELL s AC DC LED PSU l Lo ACIL ui i ACDC V AC source olf LEDPSU1 DIM Ho ACIN DIM of ACIL V ACDC V LEDPSU4 DIM to ACIN DIM LED Light Fixture DALI Bus DALI DALIe 2 controller o DALI DIM T DI IMa DAP 04 Upto 4 channels XNote Choose a suitable cable for connecting the DAP 04 and DALI controller and make sure the maximum voltage drop between these two units should not be higher than 2V Maximum cable length for 1 5mm cables is 300m b Push dim MEAN WELL s AC DC LED PSU ee a r Dimming control mechanism LfoACIL V i Fanci Pashina t ACDC V o unction ushing time AC source i LEDPSUI piMe 7 i Ye 9 LL ACIN DIM i ys amit No change of state lt 0 05 sec Bg ee Turn ON OFF 0 1 1 sec 1 E f AGM a6 Me i t fi Dimming up ordown 1 5 10 sec l a T H i 7 i LEDPSU4 DiM 1 i 9 gt LL xc are 4 Lampa Setting light to 100 11 sec es Soe sgal i It will always dim up when light
5. intensity is lower than 10 whereas ly Sees it will always dim down when light intensity is higher than 90 z LED Light Fodure Factory default dimming setting 100 4 ACIL pimi ACN Pf DM s s__lopush 2J Push dimmer Dim H paul DIMA DAP 04 XNote Only use Normally Open Push Button without light indicator c Dimming with LED PSU ON OFF Relay or magnetic switch ACIL Ve o ey Ve MEANWELL gt AG source ACN LED Light Fixture v ACIDC LED PSU javait key DiIMeo ASAN WELL LEDLigh Fixture ACIL ae Relay DiM o DIM o ACIN ACIL DIMI o ACIN DAR E E A i Figure 1 DM1 DAP 7 z Figure 2 The DAP 04 is equipped with a relay that can be used to turn ON OFF MEAN WELL LED PSUs The relay is in the closed position when the DIM1 generates dimming signal the relay is in the open position when there is no output signal on the DIM1 XNote An additional magnetic switch is needed when the total input current of the selected LED PSUs is higher than 8Aor used with LED PSUs whose inrush current is greater than 50A please refer to the figure 2 d Synchronization operation Dimmingable Dimmingable Dimmingable Dimmingable Upto 20 units
Download Pdf Manuals
Related Search