Home

KINO-9452 User Manual v1.0

1. f o Figure 3 13 SATA Drive Connector Locations PIN NO DESCRIPTION 2 2 Table 3 15 SATA Drive Connector Pinouts Page 52 1 Technology Corp KINO 9452 Motherboard M 3 2 13 SPDIF Connector CN Label SPDIF1 CN Type 5 pin header 1x5 CN Location See Figure 3 14 CN Pinouts See Table 3 16 The SPDIF connector connects to the S PDIF audio module which bears S PDIF digital output S PDIF Sony Philips Digital Interface is a newest audio transfer file format which allows the user to enjoy digital audio The SPDIF1 port provides digital audio to external speaker or compressed AC3 data to an external Dolby Digital Decoder via a coaxial cable 1515 5 5 5151515 5 SPDIF1 5 1 Figure 3 14 SPDIF Connector Locations KINO 9452 Motherboard PIN NO DESCRIPTION 1 5V 2 KEY 3 SPDIF_OUT 4 GND 5 SPDIF_IN Table 3 16 SPDIF Pinouts 3 2 14 Internal USB Connectors CN Label USB4 and USB5 CN Type 8 pin header 2x4 CN Location See Figure 3 15 CN Pinouts See Table 3 17 One 2x4 pin connector provides connectivity to two USB
2. O Wheninstalling or configuring the motherboard place it on an antistatic pad This helps to prevent potential ESD damage m Turn off all power to the KINO 9452 O When working with the motherboard make sure that it is disconnected from all power supplies and that no electricity is being fed into the system Before and during the installation of the KINO 9452 DO NOT m remove any of the stickers on the PCB board These stickers are required for warranty validation m use the product before verifying all the cables and power connectors are properly connected m allow screws to come in contact with the PCB circuit connector pins or its components 4 3 Unpacking NOTE If any of the items listed below are missing when the KINO 9452 is unpacked do not proceed with the installation and contact the KINO 9452 reseller or vendor 4 3 1 Unpacking Precautions Before installing the KINO 9452 unpack the motherboard Some components on KINO 9452 are very sensitive to static electricity and can be damaged by a sudden rush of power To protect it from being damaged follow these precautions m user should ground them self to remove any static charge before touching the KINO 9452 To do so wear a grounded wrist strap at all times or frequently touch any conducting materials that is connected to the ground m Handle the KINO 9452 by its edges Do not touch the
3. 104 VT UTF8 Combo Key 105 Sredir Memory Display Delay eese nnns 105 USB Configuratlon creer cem 105 USB Devices 106 USB Function 8 USB 106 USB 2 0 Controller Enabled scere 106 Legacy USB Support Enabled eren 106 USB2 0 Controller Mode HiSpeed ceres 107 BIOS EHCI Handoff Enabled 107 Emulation Type 1 enr tec ertt rnnt rrr nnno rano 108 Clear NVRAM 110 Plug amp Play O S No 2 icon tocco ae rinm t ande eco nine 110 PCI Latency Timer 641 52 0 nne rentre ntt teen 111 Allocate IRQ to PCI VGA 111 Palette Snooping Disabled ceres 111 PCI IDE BusMaster Enabled ceres 112 OffBoard PCI ISA IDE Card 112 IRQ
4. 38 Figure 3 4 Front Panel Connector Location eese 40 Figure 3 5 GPIO Connector 41 Figure 3 6 IDE Device Connector Location eese 42 Figure 3 7 LCD Backlight Connector 44 Figure 3 8 LVDS LCD Connector Location esee 45 Figure 3 9 Mini PCI Slot Location eese 46 Figure 3 10 Power Connector Location eese 48 Figure 3 11 14 Pin Serial Port Connector Locations sss 49 Figure 3 12 10 Pin Serial Port Connector Locations eere 50 Figure 3 13 SATA Drive Connector Locations esee 52 Figure 3 14 SPDIF Connector 53 Figure 3 15 Internal USB Connector Locations eere 55 Figure 3 16 KINO 9452 External Interface Connectors 56 Figure 3 17 Audio Connectors eese nennen enean nennt 57 Figure 3 18 57 Figure 3 19 RJ 45 Ethernet Connect
5. 29 2 12 USB INTERFACES 29 2 BIOS 29 2 14 OPERATING TEMPERATURE AND TEMPERATURE 29 KINO 9452 Motherboard _ AUDIO 30 2 16 POWER CONSUMPTION ea caet pe tenia Deni REIHE RR Hen 31 2 17 PACKAGED CONTENTS AND OPTIONAL ACCESSORY ITEMS eee 32 Contents osa dae piedi an a daa 32 2 17 2 Optional Accessory JOE 32 CONNECTORS AND JUMPERS 33 3 1 PERIPHERAL INTERFACE CONNECTORS 2 22 ptite 34 3 1 1 KINO 9452 34 3 1 2 Peripheral Interface Connectors ia avoue aei ep QU 34 3 1 3 Coda EN LLL 36 3 1 4 On board J mpets NAM PR ARM D EEE E 36 3 2 INTERNAL PERIPHERAL CONNECTORS 37 221 Fan CONBCIDES 37 3 2 2 Front Panel Audio Connector 38 3 2 3 Front Panel Connector 39 3 2 4 Digital Input Output GONHECIF 41 ORBEOROP 42 3 2 6 LCD Backlight C OECD ornati aoa hv Hv EU Rad V 43 2 cU MN
6. Figure 3 4 Front Panel Connector Location PIN NO DESCRIPTION PIN NO DESCRIPTION 1 Power LED 2 Speaker 3 NC 4 NC 5 Power LED 6 NC 7 Power Button 8 Speaker 9 Power Button 10 NC 11 IDE LED 12 Reset Button 13 I DE LED 14 Reset Button Table 3 6 Front Panel Connector Pinouts Page 40 IEI Technology Corp KINO 9452 Motherboard _ 3 2 4 Digital Input Output Connector CN Label DIO1 CN Type 10 pin header 2x6 CN Location See Figure 3 5 Pinouts See Table 3 7 The DIO connector is managed through a Super chip The DIO connector pins are user programmable The digital IO port of KINO 9452 is 5V CMOS level SSS DIO1 10 PIN DESCRIPTION PIN NO DESCRIPTION 1 GND 2 5V 3 INPUTO 4 OUTPUTO 5 INPUT1 6 OUTPUT1 7 INPUT2 8 OUTPUT2 9 INPUT3 10 OUTPUT3 Table 3 7 GPIO Connector Pinouts KINO 9452 Motherboard 3 2 5 IDE Connector CN Label IDE1 CN Type 40 pin header 2x20 CN Location See Figure 3 6 Pinouts See Table 3 8 One primary 40 pin IDE device connector on the KINO 9452 motherboard supports connectivity to ATA 100 IDE devices with data transfer rates up to 100MB s
7. 91 Block Multi Sector Transfer Auto eren 91 Mode 92 32Bit Data Transfer Enabled esee 93 Serial Port Address SF8 IRQ4 sees 94 Serial Port Mode 94 Serial Port2 Address 2F8 IRQ3 sees eene 94 Serial Port2 Mode 95 Serial Port3 Address 8 11 95 Serial Port3 IRQ 11 riri eerie uto err ceder ett 95 Serial Port4 Address 2 81 95 Serial Port4 IRQ 10 iecore ance 96 CPU FAN Mode Setting Full On mode eene 97 CPU Limit of OFF 2 er 97 CPU Temp Limit of Start 97 CPU Temp Limit of 97 CPU Fan Start PWM mc
8. enint eine ede 113 Channel eene eren ennt 114 Reserved Memory Size Disabled sees 114 Quick Boot 116 Quiet Boot 116 AddOn ROM Display Mode Force BIOS eese 117 Bootup Num Lock nennen nennen nnnm nnt 117 PS 2 Mouse Support Auto necesse nennen 117 153 KINO 9452 Motherboard Boot From LAN Support Disabled eese 118 Change Supervisor Password essent nnns 121 Change User 121 DRAM Frequency 123 Configure DRAM Timing by SPD 123 Memory Hole 0 124 Boots Graphics Adapter Priority
9. Q m Advanced power management features including Enhanced Intel SpeedStep technology m Execute Disable Bit support for enhanced security m ntel Virtualization Technology enhances virtualization robustness and performance 2 4 On board Chipsets 2 4 1 Northbridge and Southbridge Chipsets The following chipsets are preinstalled on the board Northbridge Intel 945GM Southbridge Intel ICH7 M The following two sections Section 2 4 2 and Section 2 4 3 list some of the features of the Intel 945GM and the Intel ICH7 M chipsets For more information on these two chipsets please refer to the Intel website 2 4 2 Intel 945GM Northbridge Chipset The Intel 945GM northbridge chipset comes with the following features m System Memory Support Supports single dual channel DDR2 SDRAM 64 bit wide per channel 256 MB 512 MB and 1 Gb memory technologies supported Support for DDR2 On Die Termination ODT O Support for 2N timings only O m Internal Graphics Intel Gen 3 5 Integrated Graphics Engine O 250 MHz core render clock and 200 MHz core display clock at 1 05 V core voltage O Supports TV Out LVDS CRT and SDVO m DMI O Chip to chip interface between G MCH and ICH O Configurable as x2 or x4 DMI lanes DMI lane reversal support KINO 9452 Motherboard O 32 bit downstream address Power Management ACPI S0 S3 54 55 CPU States CO C1 C2 C4 states O Rap
10. 134 Figure 6 4 Readme 134 Figure 6 5 Restart the nnne nnne 135 Figure 6 6 Starting Install Shield Wizard Screen 136 Figure 6 7 Preparing Setup enne 136 Figure 6 8 VGA Driver Installation Welcome Screen 137 Figure 6 9 VGA Driver License Agreement eene 137 Figure 6 10 VGA Driver Installing Notice eere 138 Figure 6 11 VGA Driver Installation 138 Figure 6 12 Access Windows Control Panel eese 139 Figure 6 13 Double Click the System ICON eese 140 Figure 6 14 Double Click the Device Manager 140 Figure 6 15 Device Manager eene 141 Figure 6 16 Search for Suitable Driver serere 141 Figure 6 17 Locate Driver Files necesse nennen 142 Figure 6 18 Location Browsing Window eere 142 Figure 6 19 Access Windows Control Panel eere
11. 39 pem 2 1 IDE1 Figure 3 6 IDE Device Connector Location PIN NO DESCRIPTION PIN NO DESCRIPTION RESET 2 GND Damas baras 6 Damas DATA 5 10 baras omman DATA 4 10 DATA 11 baraz oman 42 IEI Technology Corp KINO 9452 Motherboard M 9 PIN NO DESCRIPTION PIN NO DESCRIPTION 15 DATA 1 16 DATA 14 Lom m _ me ew wmm x we o pm p sm o pe meme _ s ew Table 3 8 IDE Connector Pinouts 3 2 6 LCD Backlight Connector CN Label 6 pin header 1 6 CN Location See Figure 3 7 Pinouts See Table 3 9 The LCD backlight connector is for the LCD inverter connection KINO 9452 Motherboard CN1 1 Figure 3 7 LCD Backlight Connector Location DESCRIPTION Back Light Power Back Light Power Back Light enable NC GND GND Table 3 9 LCD Backlight Connector Pinouts 3 2 7 LVDS LCD connector CN Label LVDS1 CN Type 30 pin connector 2x15 Page 44 IEI Technology Corp KINO 9452 Motherboard M aal CN Location See Figure 3 8 CN Pinouts See Table 3 10 The conne
12. InstallShield Wizard InstallShield Wizard which will quide you through the rest of the Intel R Chipset Software Installation Utility Setup is preparing the Sa setup process Please wait Figure 6 1 InstallShield Wizard Preparation Screen Step 3 The Welcome window in Figure 6 2 appears next Welcome to the InstallShield R Wizard for Intel R Chipset Software Installation Utility Welcome to the Intel R Chipset Software Installation Utility This utility will enable Plug amp Play INF support for Intel R chipset components Figure 6 2 Welcome Screen Step 4 Click NEXT and the license agreement shown in Figure 6 3 appears Page 133 KINO 9452 Motherboard Setup x License Agreement Please read the following license agreement carefully Press the PAGE DOWN key to see the rest of the agreement NTEL SOFTWARE LICENSE AGREEMENT IHV IS Distribution amp Single User IMPORTANT READ BEFORE COPYING INSTALLING OR USING Do not use or load this software and any associated materials collectively the Software until you have carefully read the following terms and conditions By loading or using the Software you agree to the terms of this Agreement If you do not wish to so agree do not install or use the Software Please Also Note f you are an Original Equipment Manufacturer Independent Hardware Vendor Do you accept all the terms of the
13. 97 CPU Fan PWM Cohltol norat ttd tne sunessnceneececeeetnesdepceseceetente 97 ACPI Aware O S croire cucurrit euni ca ne rna imm canne 98 Suspend mode S3 99 Power Management APM Enabledq eese 100 Restore AC Power Loss by IO Power Off esee 101 Power Button Mode On Off cecus eeeeeeeeeeneeenne nennen 101 Resume on Ring 101 Resume ennt 101 152 IEI Technology Corp KINO 9452 Motherboard Resume On Alarm Disabled cese 102 RTC Alarm Date 102 Resume On PCI Express WAKE 102 5 Revision 1 4 2 irren incen t Eoi Re nan 103 Remote Access Disabled cessere eene nnn 104 Serial Port Number rccte nennen 104 Redirection after BIOS
14. 44 ec d NQBRUS 46 32 9 Pow r Connector iussa m p erp DM NE eee 48 3 2 10 14 Pin Serial Fort COnBBClQPE 49 3 2 11 10 Pin Serial Port 50 3 2 12 SATA Drive GORnBECIOTS 51 32A3 SPDIF C RM edt 53 3 2414 Internal USB CONNECTIONS spin RENS V AS e UA ts 54 3 3 EXTERNAL INTERFACE CONNECTORS iiecii tutor dern sera 55 22 1 UIDES Turri 56 3 3 2 57 58 3 3 4 Keyboard Mouse Connector scsccsasenacorsenancecannandstdenandsaanvanseaeonanceadonansendiwsadeancpans 59 3 3 3 Serial Port Connectors secorrir ia e a itai 60 3 3 6 TV Out Connector Ee 61 3 3 7 USB Connector T 62 4 INSTALLATION AND CONFIGURATION 63 KINO 9452 Motherboard 4 1 ANTI STATIC PRECAUTIONS a pra best 64 4 2 INSTALLATION CONSIDERATIONS 64 4 2 1 Installati n NOTICES Rc E 64 4 lh Gee Oe ee 65 4 3 1 Unpacking 65 4 3 2 66 4 4 KINO 9452 MOTHERBOARD 5 4 8 88 66 44 1 CPU Installation E 67 4 4 2 Cooling Kit CF 479B RS Installation
15. 163 KINO 9452 Motherboard Index 164 IEI Technology Corp KINO 9452 Motherboard 4 3D graphic 16 Acoustic Echo Cancellation 31 ALC883 6 19 30 31 132 143 AMI BIOS 5 20 29 81 82 84 ASF2 0 20 ATX power 20 48 Audio jacks 18 55 Beam Forming 31 CD ROM 56 90 92 109 Center Subwoofer port 56 chassis 37 38 55 78 Clear CMOS 5 18 36 75 76 77 Duo 3 16 19 23 24 Solo 3 16 19 23 24 CPU cooler 32 66 DAC channel 30 DB 9 36 60 74 DDR2 16 17 19 25 27 31 35 67 71 Digital I O 17 19 DMA controller 26 162 DMI lane 25 Dual core 16 24 DVD player 31 56 Electrostatic discharge 64 front panel 30 38 39 Front panel 17 35 HDTV 16 17 19 27 32 66 73 High Definition Audio 26 30 79 128 I O shielding 32 66 IC chips 65 ICH7 M 3 19 25 26 Integrated Heat Sink 68 Intel 945GM 3 19 25 26 161 Intel Active Management Technology 26 Intel Matrix Storage Technology 26 L1 cache 16 87 L2 cache 16 24 87 LCD backlight 18 27 35 43 LCD panel 78 LCD voltage 18 36 75 memory module 19 67 72 Mini PCI 4 16 18 19 35 46 47 Mini ITX 16 multi media application 16 Noise Suppression 31 Northbridge 3 19 25 35 37 On Die Termination 25 PCB board 65 PCBEEP 30 PCI 3 6
16. 113 KINO 9452 Motherboard m 15 gt DMA Channel Available Use the option to assign a specific channel to a particular PCI PnP device gt Available DEFAULT The specified DMA is available to be used by PCI PnP devices gt Reserved The specified DMA is reserved for use by Legacy ISA devices Available DMA Channels are m Channel 0 wm Channel 1 Channel 3 Channel 5 Channel 6 m Channel 7 Reserved Memory Size Disabled Use the Reserved Memory Size BIOS option to specify the amount of memory that should be reserved for legacy ISA devices gt Disabled DEFAULT No memory block reserved for legacy ISA devices gt 16K 16KB reserved for legacy ISA devices gt 32K 32KB reserved for legacy ISA devices gt 64 reserved for legacy ISA devices 114 IEI Technology Corp KINO 9452 Motherboard 5 5 Boot Use the Boot menu BIOS Menu 16 to configure system boot options BIOS SETUP UTILITY gt Boot Settings Configuration BIOS Menu 16 Boot 5 5 1 Boot Settings Configuration Use the Boot Settings Configuration menu BIOS Menu 17 to configure advanced system boot options 115 KINO 9452 Motherboard BIOS SETUP UTILITY Quick Boot Enabled BIOS Menu 17 Boot Settings Configuration Quick Boot Enabled
17. Figure 3 2 Fan Connector Locations KINO 9452 Motherboard PIN NO DESCRIPTION 1 GND 2 12V 3 Sense Table 3 4 Fan Connector Pinouts 3 2 2 Front Panel Audio Connector CN Label AUDIO2 CN Type 10 pin header 2x5 CN Location See Figure 3 3 CN Pinouts See Table 3 5 The front panel audio connector connect the on board sound system of the KINO 9452 to the audio line out and microphone jacks on the front of the computer chassis AUDIO2 1090 gt 2091 Figure 3 3 Front Panel Audio Connector Location 38 1 Technology Corp KINO 9452 Motherboard PIN DESCRIPTION PIN NO DESCRIPTION 1 Portl L 2 GND 3 Port1_R 4 PRESENCE 5 Port2_R 6 SENSE1_RETUR 7 SENSE_SEND 8 KEY 9 Port2_L 10 SENSE2_RETUR Table 3 5 Front Panel Audio Connector Pinouts 3 2 3 Front Panel Connector CN Label F PANEL1 CN Type 14 pin header 2x7 CN Location See Figure 3 4 Pinouts See Table 3 6 The front panel connector connects to several external switches and indicators to monitor and control the motherboard These indicators and switches include m Power m Power button m Reset button m Speaker HDD KINO 9452 Motherboard
18. JO ADVANCED er E eee 85 3 3 1 CPU tm 86 9 9 2 IDE 87 5 3 2 1 IDE Master IDE Slave eese 89 5 3 3 Super 93 5 3 4 Hardware Health 1 96 Dad ld ACPI PTT 98 5 3 9 General sini s 99 SOLO APM COR EDHPULOR MIRI MEUS 100 5 3 7 MPS GOnfi imm 102 5 3 8 Remote Access Configuration 103 SPESE restart akute qaa IU baud uon dau a uad 105 5 3 9 1 USB Mass Storage Device Configuration esee 107 54 PRU PMP e 109 115 5 5 1 Boot Settings 1 115 5 3 2 Boot Device Priority 118 3 3 3 Removable Drives 119 5 O 120 ANE CHIPSET eos face nerie 122 5 7 1 North Bridge CONT OUT GION 122 5 7 1 1 Video Function Configuration 125 5 7 2 South Bridge 128 A P 129 6 SOFTWARE DRIVERS 131 6 1 AVAILABLE SOFTWARE DRIVERS 132 6 2 CHIPSET DRIVER INSTALLATION reb ep yess o d ape IR deus 132 0 3 VGA DRIVER c H u 135 6 4 BROADCOM LAN DRIVER FOR GBE LAN INSTALLATION 139 6 5 REALTEK AUD
19. WARNING Setting wrong values for the BIOS selections in the PCIPnP BIOS menu may cause the system to malfunction 109 KINO 9452 Motherboard BIOS SETUP UTILITY Clear NURAM BIOS Menu 15 PCI PnP Configuration Clear NVRAM No Use the Clear NVRAM option to specify if the NVRAM Non Volatile RAM is cleared when the power is turned off gt No DEFAULT System does not clear NVRAM during system boot gt Yes System clears NVRAM during system boot Plug amp Play O S No Use the Plug amp Play O S BIOS option to specify whether system plug and play devices are configured by the operating system or the BIOS gt No DEFAULT f the operating system does not meet the Plug and Play Page 110 echnology Corp KINO 9452 Motherboard M M M M specifications this option allows the BIOS to configure all the devices in the system gt Yes This setting allows the operating system to change the interrupt and DMA settings Set this option if the system is running Plug and Play aware operating systems PCI Latency Timer 64 Use the PCI Latency Timer option to specify the PCI latency time The latency time is measured in units of PCI clock cycles for the PCI device latency timer register Configuration options are m 32 m 64 DEFAULT m 96 m 128 m 160 m 192 m 224 m 248 Allocate IRQ to PCI VGA Yes Use
20. Step 3 Secure the cooling kit From the solder side of the PCB align the support bracket to the screw threads on heat sink that were inserted through the PCB holes See Figure 4 4 Support Bracket Figure 4 4 Securing the Cooling Kit Step 4 Tighten the screws Use a screwdriver to tighten the four screws Tighten each nut a few turns at a time and do not over tighten the screws Step 5 Connect the fan cable Connect the cooling kit fan cable to the fan connector on the motherboard Carefully route the cable and avoid heat generating chips and fan blades See Figure 4 5 Technology Corp KINO 9452 Motherboard _ Heatsink Figure 4 5 Connect the cooling fan cable 4 4 3 DIMM Module Installation 4 4 3 1 Purchasing the Memory Module WARNING When purchasing the DIMM modules make sure the modules are compatible with the DIMM slot specified in Section 2 6 Memory Support WARNING The board supports DDR2 DIMM modules only DDR1 and DDR2 are not compatible If a DDR1 DIMM module is installed the system may be damaged and become inaccessible Please only use DDR2 DIMM modules 4 4 3 2 DIMM Module Installation The KINO 9452 has two 240 pin DDR2 SDRAM DIMM sockets Follow the steps below to install the DIMM modules Step 1 Make sure the two handles of the DIMM socket are in the open position leaning outward Figure 4 6 KINO 9452 Motherboard y
21. cesses 69 4 4 3 DIMM Module Installation 71 4 4 3 1 Purchasing the Memory Itin n apo ann tpa Sedona rad eR 71 4 4 3 2 DIMM Module Installation 71 4 4 4 Peripheral Device 73 4 4 4 1 IDE Disk Drive Connector 73 4 4 4 2 COM Poft 74 4 5 ON BOARD JUMPERS T 75 4 5 1 Clear CMOS 00 7 T 76 4 5 2 COM2 Mode Selection 77 4 5 3 LVDS LCD Voltage SeleGlion 78 4 6 CHASSIS INSTALLATION 78 4 7 REAR PANEL CONNECTORS 79 2 74 LCD Panel Connectiots a Es 79 4 1 2 Coe QUI rr p NEM REIN 79 443 USB G nnecti t Nr 79 LUE Serial cT 79 4 7 5 Keyboard and Mouse Connection eese etai 79 4 7 06 Audio u pU MER ME M TUE RN 79 5 AMI BIOS SETUP 81 1 INTRODUCTION et 82 RFID Nc 82 3 1 2 Using 82 Help ERR 83 5 1 4 Unable to Reboot after Configuration Changes 83 3 1 9 BIOS Men 83 KINO 9452 Motherboard p y y y o o
22. Numeric data processor 120 127 Primary IDE Channel 2E8 2EF Serial Port 4 COM4 2F8 2FF Serial Port 2 378 37F Parallel Printer Port 1 LPT1 3B0 3BB Intel 945GM Graphics Controller 3C0 3DF Intel 945GM Graphics Controller 3E8 3EF Serial Port 3 COM3 3F6 3F6 Primary IDE Channel 3F7 3F7 Standard floppy disk controller 3F8 3FF Table C 1 IO Address Map Serial Port 1 COM1 C 2 1st MB Memory Address Map YACCKINTIAN 2SCription 00000 9FFFF System memory A0000 BFFFF buffer F0000 FFFFF System BIOS Extend BIOS Table C 2 1 MB Memory Address Map 161 KINO 9452 Motherboard IRQO System Timer IRQ8 RTC clock 1 IRQ9 ACPI IRQ2 Available IRQ10 COM 4 IRQ3 COM2 IRQ11 COM 3 1894 COMI IRQ12 PS 2 mouse IRQ5 SMBus Controller IRQ13 FPU IRQ6 FDC IRQ14 Primary IDE IRQ7 Parallel port IRQ15 Secondary IDE Table C 3 IRQ Mapping Table C 4 DMA Channel Assignments hannel Available Available Floppy disk 8 bit transfer Available Cascade for DMA controller 1 Available Available Table C 4 Available DMA Channel Assignments 162 IEI Technology Corp KINO 9452 Motherboard _ _ _ THIS PAGE IS INTENTIONALLY LEFT BLANK
23. Technology Corp KINO 9452 Motherboard _ _ _ THIS PAGE IS INTENTIONALLY LEFT BLANK Page 155 KINO 9452 Motherboard Watchdog Timer Page 156 Technology Corp KINO 9452 Motherboard The following discussion applies to DOS environment IEI support is contacted or the IEI website visited for specific drivers for more sophisticated operating systems e g Windows and Linux The Watchdog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that cause the CPU to crash This condition may have occurred by external EMI or a software bug When the CPU stops working correctly Watchdog Timer either performs a hardware reset cold boot or a Non Maskable Interrupt NMI to bring the system back to a known state A BIOS function call INT 15H is used to control the Watchdog Timer INT 15H AH 6FH Sub function AL 2 Sets the Watchdog Timer s period BL Time out value Its unit second is dependent on the item Watchdog Timer unit select in CMOS setup Table B 1 AH 6FH Sub function Call sub function 2 to set the time out period of Watchdog Timer first If the time out value is not zero the Watchdog Timer starts counting down While the timer value reaches zero the system resets To ensure that this reset condition does not occur calling sub function 2 must per
24. Use the Quick Boot BIOS option to make the computer speed up the boot process gt Disabled No POST procedures are skipped gt Enabled DEFAULT Some POST procedures are skipped to decrease the system boot time Quiet Boot Disabled Use the Quiet Boot BIOS option to select the screen display when the system boots gt Disabled DEFAULT Normal POST messages displayed gt Enabled OEM Logo displayed instead of POST messages Page 116 echnology Corp KINO 9452 Motherboard MM AddOn ROM Display Mode Force BIOS Use the AddOn ROM Display Mode option to allow add on ROM read only memory messages to be displayed gt 5 DEFAULT The system forces third party BIOS to display during system boot gt Keep Current The system displays normal information during system boot Bootup Num Lock On Use the Bootup Num Lock BIOS option to specify if the number lock setting must be modified during boot up gt Off Does not enable the keyboard Number Lock automatically To use the 10 keys on the keyboard press the Number Lock key located on the upper left hand corner of the 10 key pad The Number Lock LED on the keyboard lights up when the Number Lock is engaged gt On DEFAULT Allows the Number Lock on the keyboard to be enabled automatically when the computer system boots up This allows the immediate use of the 10 key numeric keypad loca
25. Chapter 1 Introduction 15 KINO 9452 Motherboard 1 1 KINO 9452 Overview The Mini ITX form factor KINO 9452 with Intel Core 2 Duo Core Solo CPU platform is fully equipped with latest technology and advanced multi mode I Os The KINO 9452 is designed for system manufacturers integrators and VARs that want performance reliability and quality at a reasonable price 1 1 1 KINO 9452 Benefits Some of the KINO 9452 benefits include Dual core Intel processor support O Two physical cores in a package share the system load O Each core has its own L1 cache and shares the L2 cache to enhance the processing speed O High performance levels especially in 3D graphic and multi media application Independent dual audio with HDTV output m Excellent thermal control that enhance voltage efficiency and supports cooler and quieter systems m Mini PCI expansion slot and rich interface O Integrates a PCI and a mini PCI slot for flexible expansion capabilities O Integrates TV out and multi channel audio for related applications wm DDR2 memory technology supported m II with 3 0Gb s transfer rate wm Dual PCle GbE enhance high performance in network 1 1 2 KINO 9452 Features Some of the KINO 9452 features are listed below m Complies with RoHS Supports Intel Core 2 Duo Core Duo and Core Solo processor m Supports a maximum front side bus FSB speed up to 667MHz m Supports up to 2GB of 4
26. Install Hardware Device Drivers device driver is a software program that enables a hardware device to work with an operating system This wizard upgrades drivers for the following hardware device 532DD36TA0378H annStar U171 CS Uparading to newer version of a device driver may add functionality to or improve the performance of this device What do vou want the wizard to do Search for a suitable driver for my device recommended C Display list of the known drivers for this device so that can choose a specific driver lt Back Next gt Figure 6 23 Search for Suitable Driver Step 7 Select Specify a Location in the Locate Driver Files window Figure 6 17 Click NEXT to continue 146 Technology Corp KINO 9452 Motherboard Upgrade Device Driver Wizard Locate Driver Files Where do you want Windows to search for driver files S Search for driver files for the following hardware device m 532DD3BTA037SHannStar U171 The wizard searches for suitable drivers in its driver database on your computer and in any of the following optional search locations that you specify To start the search click Next If vou are searching on a floppy disk or CD ROM drive insert the floppy disk or CD before clicking Next Optional search locations Floppy disk drives lt Back Cancel Figure 6 24 Locate Driver Files Step 8 Select X M AUDIO AC KIT
27. KINO 9452 Motherboard OnBoard LAN1 BCM5787M Enabled The OnBoard LAN1 BCM5787M option enables or disables the onboard LAN1 Disabled Onboard LAN1 controller manually disabled gt Enabled DEFAULT The onboard controller automatically detected and enabled OnBoard LAN2 BCM5787M Enabled The OnBoard LAN2 BCM5787M option enables or disables the onboard LAN1 gt Disabled Onboard LAN2 controller manually disabled gt Enabled DEFAULT The onboard LAN2 controller automatically detected and enabled 5 8 Exit Use the Exit menu BIOS Menu 24 to load default BIOS values optimal failsafe values and to save configuration changes BIOS SETUP UTILITY Save Changes and Exit BIOS Menu 24 Exit Page 129 KINO 9452 Motherboard Save Changes and Exit Use the Save Changes and Exit option to save the changes made to the BIOS options and to exit the BIOS configuration setup program Discard Changes and Exit Use the Discard Changes and Exit option to exit the BIOS configuration setup program without saving the changes made to the system Discard Changes Use the Discard Changes option to discard the changes and remain in the BIOS configuration setup program Load Optimal Defaults Use the Load Optimal Defaults option to load the optimal default values for each of the parameters on the Setup menus F9 k
28. OUT TTN DDR DIMM notch Unlocked Retaining Clip Figure 4 6 Installing the DIMM Module Step 2 Slowly slide the DIMM module along the plastic guides on both ends of the socket Press the DIMM module down into the socket until it clicks into position and the two handles have automatically locked the memory module into place Figure 4 7 NETA Locked Retaining Clip Figure 4 7 Locking the DIMM Module Step 3 To remove the memory module push both handles outward and the memory Page 72 ipie Technology Corp KINO 9452 Motherboard module is ejected by the mechanism in the socket 4 4 4 Peripheral Device Connection Cables provided by IEI that connect peripheral devices to the motherboard are listed in Table 4 1 Cables not included in the kit must be separately purchased Quantity Type 1 IDE flat cable 2 SATA cables 1 SATA power cable 2 RS 232 cables 1 HDTV out cable Table 4 1 IEI Provided Cables 4 4 4 1 IDE Disk Drive Connector IDE1 The cable used to connect the motherboard to the IDE device is a standard 40 pin ATA 100 flat cable To connect an IDE device to the motherboard follow the instructions below Step 1 Step 2 Step 3 Step 4 Find the IDE flat cable in the kit that came with the motherboard Connect one end of the cable to the IDE connector on the motherboard A keyed
29. pin on the IDE connector prevents it from being connected incorrectly Locate the red wire on the other side of the cable that corresponds to the pin 1 connector Connect the other side of the cable to the IDE device making sure that the pin 1 cable corresponds to pin 1 on the connector KINO 9452 Motherboard Figure 4 8 Connection of IDE Connector When two IDE disk drives are connected together back end jumpers the drives must be used to configure one drive as a master and the other as a slave 4 4 4 2 COM Port Connectors The KINO 9452 provides four serial ports COM1 COM2 COM3 and COM4 interfaced through two 10 pin male headers COM3 and one 14 pin male headers COM2 and one DB 9 connector 1 The serial ports facilitate the connection to serial devices or a communications network e g terminal console Page 74 IEI Technology Corp KINO 9452 Motherboard 4 5 On board Jumpers A NOTE A jumper is a metal bridge that is used to close an electrical circuit It PLASTIC CLIP OPEN CLOSED consists of two metal pins and a small metal clip often protected by a plastic cover that slides over the pins to connectthem To CLOSE SHORT a jumper means connecting the pins of the jumper with the plastic clip and to OPEN jumper means removing the plastic clip from a jumper Figure 4 9 Jumper The KINO
30. 12V 20 5V Table 3 12 Power Connector Pinouts 3 2 10 14 Pin Serial Port Connectors CN Label COM2 CN Type 14 pin header 2x7 CN Location See Figure 3 11 CN Pinouts See Table 3 13 The serial ports connectors connect to RS 232 422 485 serial port device 2 14 d Figure 3 11 14 Pin Serial Port Connector Locations KINO 9452 Motherboard PIN NO DESCRIPTION PIN NO DESCRIPTION Table 3 13 COM2 Pinouts 3 2 11 10 Pin Serial Port Connectors CN Label COM3 and COM4 CN Type 10 pin header 2x5 CN Location See Figure 3 12 CN Pinouts See Table 3 14 The serial ports connectors connect to RS 232 serial port device COM4 Figure 3 12 10 Pin Serial Port Connector Locations Page 50 Technology Corp KINO 9452 Motherboard PIN NO DESCRIPTION PIN NO DESCRIPTION Table 3 14 COM3 and COM4 Pinouts 3 2 12 SATA Drive Connectors CN Label SATA1 and SATA2 CN Type 1x7 pin SATA drive connectors CN Location See Figure 3 13 CN Pinouts See Table 3 15 The two SATA drive connectors are connected to four SATA Il drives SATA II drives transfer data at speeds as high as 3 0Gb s KINO 9452 Motherboard
31. 13 16 18 19 20 26 27 28 35 46 47 83 101 102 109 110 111 112 113 114 124 125 power consumption 24 31 PS 2 59 60 79 117 118 162 RAMDAC 26 RJ 45 36 55 58 59 79 RoHS 16 rotation signal 37 RS 232 cables 32 66 73 RS 232 422 485 cable 32 66 SATA cables 32 66 73 SATA Il 16 18 19 28 51 SATA power cable 32 66 73 SDVO 25 27 Side Speaker Out port 56 Socket 479 69 SPDIF 4 18 35 53 54 SpeedStep technology 24 25 Spread spectrum clocking 27 Streaming SIMD Extensions 3 24 165 KINO 9452 Motherboard SuperlO 85 TV Out 4 18 25 27 36 56 61 62 TFT panel 27 USB 2 0 17 18 19 26 29 36 54 56 106 Page 166 1 Technology Corp
32. PEG PCI sees 124 Internal Graphics Mode Select Enable 8MB 125 PEG Force X1 125 DVMT Mode Select DVMT ModeJ eere 126 DVMT FIXED Memory 128 1 126 Boot Display Device 126 Flat Panel Type 640 480 127 Local Flat Panel Scaling Auto eese 127 TV Connector n nnnm enhn tn anas anas anna 127 TV Standard eieneeeeenen ennt 127 Audio Controller eren nnns 128 OnBoard LAN1 BCM5787M 129 OnBoard LAN2 BCM5787M 129 Save Changes and Exit eese 130 Discard Changes and Exit eese eeeeeee nenne enne natnra tnnt 130 Discard eim 130 Load Optimal sienne nennen nnne anna annnm rnnt 130 Load Failsafe 130 154
33. 1000 transceiver m 10 100 1000 full half duplex MAC m Automatic MDI crossover function m Supports PCle v1 0a m Wake on LAN support meeting the ACPI requirements m Statistics for SNMP MIB II Ethernet like MIB and Ethernet MIB 802 32 clause 30 m Serial EEPROM or serial flash supported m JTAG supported m 196 FBGA package 2 9 Drive Interfaces The KINO 9452 can support the following drive interfaces m 2xSATAdrives m 2xIDE devices 2 9 1 SATA Drives The KINO 9452 supports two SATA II drives with transfer rates of up to 3 0Gb s 2 9 2 IDE Interfaces The KINO 9452 southbridge chipset IDE controller supports up to two IDE devices with the following specifications m Supports PIO IDE transfers up to 16MB s m Supports Ultra ATA 100 devices with data transfer rates up to 100MB s 28 IEI Technology Corp KINO 9452 Motherboard 2 10 Serial Ports The KINO 9452 has four high speed UART serial ports configured as COM1 COM2 COMS The serial ports have the following specifications m 160550 UART with 16 byte FIFO buffer m 115 2Kbps transmission rate 2 11 Real Time Clock 256 byte battery backed CMOS SRAM 2 12 USB Interfaces The KINO 9452 supports eight USB interfaces four internal and four external The USB interfaces support USB 2 0 2 13 BIOS The KINO 9452 uses a licensed copy of AMI BIOS The features of the fl
34. 143 Figure 6 20 Double Click the System ICON eese 144 Figure 6 21 Double Click the Device Manager 144 Figure 6 22 Device Manager 145 Figure 6 23 Search for Suitable Driver eere 146 Figure 6 24 Locate Driver 147 Figure 6 25 Preparing Setup Screen eese 148 KINO 9452 Motherboard ee List of Tables Table 1 1 Technical Specifications 20 Tabl 2 1 Supported CPUS ere 23 Table 2 2 Power Consumption nennen nennen nennt 31 Table 3 1 Peripheral Interface 35 Table 3 2 Rear Panel 36 Table 3 3 On board Jumpers 36 Table 3 4 Fan Connector Pinouts esee eene nnne 38 Table 3 5 Front Panel Audio Connector Pinout eene 39 Table 3 6 Front Panel Connector Pinouts eese 40 Table 3 7 GPIO Connector Pinout
35. 9452 motherboard has three on board jumpers The jumpers are described in Table 4 2 Description Label Type Clear CMOS JP3 3 pin header COM2 mode selection JP1 3 pin header LVDS LCD voltage selection JP2 6 pin header Table 4 2 On board Jumpers KINO 9452 Motherboard 6205 2001 1 JP2 Figure 4 10 Jumper Locations 2 4 5 1 Clear CMOS Jumper Jumper Label JP3 Jumper Type 3 pin header Jumper Settings See Table 4 3 Jumper Location See Figure 4 10 If the KINO 9452 fails to boot due to improper BIOS settings use this jumper to clear the CMOS data and reset the system BIOS information do this use the jumper cap to close pins 2 and 3 for a few seconds then reinstall the jumper clip back to pins 1 and 2 Page 76 IEI Technology Corp KINO 9452 Motherboard If the CMOS Settings Wrong message is displayed during the boot up process the fault may be corrected by pressing the F1 to enter the CMOS Setup menu Do one of the following m Enter the correct CMOS setting m Load Optimal Defaults m Load Failsafe Defaults After having done one of the above save the changes and exit the CMOS Setup menu Clear CMOS DESCRIPTION Shorti 2 Normal Operation Default Short 2 3 Clear CMOS Setup Table 4 3
36. ACPI 98 General ACPI Configuration Advanced Configuration 99 APM Configuration i nter enira nece ente 100 MPS Configuration e eeeeeeeeeeeeeeee nennen nennen nnn 103 Remote Access Configuration Advanced 104 USB Corfig ratlon erri 105 USB Mass Storage Device Configuration 108 PCI PnP Configuration eese nnns 110 115 Boot Settings 116 Boot Device Priority Settings essere 119 Removable 120 SO CUIINY 121 122 North Bridge Chipset Configuration ee 123 South Bridge Chipset Configuration 128 gue 129 KINO 9452 Motherboard Glossary AC 97 ACPI APM ARMD ASKIR ATA BIOS CFII CMOS CPU Codec COM DAC DDR DIMM DIO DMA EIDE EIST FDD FDC FFIO FIFO FSB IrDA Audio Codec 97 Advanced Configuration and Power Interface Advanced Power Management ATAPI Removable M
37. Auto Use the Emulation Type BIOS option to specify the type of emulation BIOS has to provide for the USB device A NOTE Please note that the device s formatted type and the emulation type provided by the BIOS must match for a device to boot properly If both types do not match then device s behavior is undefined To make sure both types match format the device using BIOS INT 13h calls after selecting the 108 echnology Corp KINO 9452 Motherboard y y y Y proper emulation option in BIOS setup The FORMAT utility provided by Microsoft MS DOS Microsoft Windows 95 and Microsoft Windows 98 can be used for this purpose Auto Floppy Forced FDD HardDisk cpRoM 5 4 PCI PnP DEFAULT BIOS auto detects the current USB The USB device will be emulated as a floppy drive The device can be either A or B responding to INT13h calls that return DL O or DL 1 respectively Allows a hard disk image to be connected as a floppy image This option works only for drives formatted with FAT12 FAT16 or FAT32 Allows the USB device to be emulated as hard disk responding to INT13h calls that return DL values of 80h or above Assumes the CD ROM is formatted as bootable media All the devices that support block sizes greater than 512 bytes can only be booted using this option Use the PCI PnP menu BIOS Menu 15 to configure advanced PCI and PnP settings
38. IC chips leads or circuitry if not necessary KINO 9452 Motherboard Do not place a PCB on top of an anti static bag Only the inside of the bag is safe from static discharge 4 3 2 Checklist When unpacking the KINO 9452 please make sure that the package contains the following items m 1xKINO 9452 single board computer m 1 IDE flat cable m 2 SATA cables m 1x SATA power cable m 2x RS 232 cables m 1x HDTV out cable m 1x I Oshielding m 1x Mini jumper pack m 1x Utility CD m 1 x Quick Installation Guide m CPU cooler optional m USB cable optional m RS 232 422 485 cable optional If one or more of these items are missing please contact the reseller or vendor the KINO 9452 was purchased from and do not proceed any further with the installation 4 4 KINO 9452 motherboard Installation A WARNING 1 Never run the motherboard without an appropriate heat sink and cooler that can be ordered from IEI Technology or purchased separately 2 sure to use the CPU 12V power connector for the CPU power WARNING Please note that the installation instructions described in this manual should 66 1 Technology Corp KINO 9452 Motherboard be carefully followed in order to avoid damage to the motherboard components and injury to the user A WARNING When installing electronic components onto the motherboard always take the following anti static precautions in order to prev
39. LAN The pin assignments are listed in the following table PIN DESCRIPTION PIN DESCRIPTION Table 3 19 LAN1 and LAN2 Pinouts SPEED ACT LINK LED LED Figure 3 19 RJ 45 Ethernet Connector Technology Corp KINO 9452 Motherboard The RJ 45 Ethernet connector has two status LEDs one green and one yellow The green LED indicates activity on the port and the yellow LED indicates the port is linked See Table 3 20 SPEED LED ACT LINK LED STATUS DESCRIPTION STATUS DESCRIPTION 10Mbps connection OFF No link 100Mbps connection YELLOW 1Gbps connection BLI NKI NG Data Activity Table 3 20 RJ 45 Ethernet Connector LEDs 3 3 4 Keyboard Mouse Connector CN Label KBMS1 CN Type PS 2 connector CN Location See Figure 3 16 labeled number 1 Pinouts See Table 3 21 The KINO 9452 keyboard and mouse connectors are standard PS 2 connectors Mouse Keyboard Figure 3 20 PS 2 Pinouts KINO 9452 Motherboard LE DESCRIPTION CIE DESCRIPTION Table 3 21 PS 2 Connector Pinouts 3 3 5 Serial Port Connectors CN Label CRT_COM1 CN Type DB 9 CN Location See Figure 3 16 labeled number 2 CN Pinouts See Table 3 22 The serial ports can be connected to a serial communications device directly Figure 3 21 External Serial Port Connector DATA CARRI ER D
40. Motherboard BIOS SETUP UTILITY MPS Revision BIOS Menu 11 MPS Configuration MPS Revision 1 4 Use the Multiprocessor Specification MPS Revision option to specify the MPS version to be used 1 1 MPS version 1 1 is used 44 DEFAULT MPS version 1 4 is used 5 3 8 Remote Access Configuration Use the Remote Access Configuration menu BIOS Menu 12 to configure remote access parameters The Remote Access Configuration is an AMIBIOS feature and allows a remote host running a terminal program to display and configure the BIOS settings 103 KINO 9452 Motherboard BIOS SETUP UTILITY Remote ficcess Disabled BIOS Menu 12 Remote Access Configuration Advanced Remote Access Disabled Use the Remote Access option to enable or disable access to the remote functionalities of the system gt Disabled DEFAULT Remote access is disabled gt Enabled Remote access configuration options shown below appear Serial Port Number Serial Port Mode Flow Control Redirection after BIOS POST Page 104 echnology Corp KINO 9452 Motherboard M M M 4 2 Terminal Type VT UTF8 Combo Key Support Sredir Memory Display Delay These configuration options are discussed below 5 3 9 USB Configuration Use the USB Configuration menu BIOS Me
41. Page 140 IEI Technology Corp KINO 9452 Motherboard a 4 Device Manager Disk drives Display adapters DVD CD ROM drives 3 Floppy disk controllers Human Interface Devices 19 99 IDE ATAJATAPI controllers E Keyboards H Mice and other pointing devices m Monitors 88 Network adapters E Ports COM amp LPT T Sound video and game controllers 19 8 System devices 1 Universal Serial Bus controllers Figure 6 15 Device Manager List Step 5 Double click the listed device that has question marks next to it This means Windows does not recognize the device Step 6 The Device Driver Wizard appears Figure 6 16 Click NEXT to continue Upgrade Device Driver Wizard Install Hardware Device Drivers device driver is a software program that enables a hardware device to work with an operating system Figure 6 16 Search for Suitable Driver Page 141 KINO 9452 Motherboard Step 7 Select Specify a Location in the Locate Driver Files window Figure 6 17 Click NEXT to continue Upgrade Device Driver Wizard Locate Driver Files Where do you want Windows to search for driver files Search for driver files for the following hardware device m 532DD36TA0379HannStar U171 The wizard searches for suitable drivers in its driver database on your computer and in any o
42. example if only one FDD is connected only 151 Drive is listed 119 KINO 9452 Motherboard The boot sequence from the available devices is selected If the 1st Drive option is selected a list of available removable drives is shown Select the first drive the system boots from If the 151 Drive is not used for booting this option may be disabled BIOS SETUP UTILITY 1st Drive USB T3S256MJFLASHA BIOS Menu 19 Removable Drives 5 6 Security Use the Security menu BIOS Menu 20 to set system and user passwords Page 120 echnology Corp KINO 9452 Motherboard 9 BIOS SETUP UTILITY Change Supervisor Password BIOS Menu 20 Security Change Supervisor Password Use the Change Supervisor Password to set or change a supervisor password The default for this option is Not Installed If a supervisor password must be installed select this field and enter the password After the password has been added Install appears next to Change Supervisor Password gt Change User Password Use the Change User Password to set or change a user password The default for this option is Not Installed user password must be installed select this field and enter the password After the password has been added Install appears next to Change User Password Page 121 KINO 9452 Motherboard 5 7 Chipset Use the Chipse
43. front panel output m 2 stereo ADCs support 16 20 24 bit PCM format one for stereo microphone the other for legacy mixer recording m All DACs support 44 1k 48k 96k 192kHz sample rate m All ADCs support 44 1k 48k 96kHz sample rate m 16 20 24 bit S PDIF OUT supports 44 1k 48k 96k 192kHz sample rate m 16 20 24 bit S PDIF IN supports 44 1k 48k 96kHz sample rate m Up to four channels of microphone array input are supported for AEC BF application m High quality analog differential CD input m Supports external PCBEEP input and built in digital BEEP generator m Software selectable 2 5V 3 75V VREFOUT m Two jack detection pins each designed to detect up to 4 jacks m Reserve analog mixer architecture for backward compatibility with AC 97 m Wide range 80dB 42dB volume control with 1 5dB resolution of analog to analog mixer gain m All analog jacks are stereo input and output re tasking for analog plug amp play m Built in headphone amplifiers for each re tasking jack m 2GPIOs General Purpose Input Output for customized applications Power support Digital 3 3V Analog 3 0V 5 0V Minimum AVDD is 3 0V m Pin compatible with the ALC880 and ALC882 m Enhanced S PDIF IN circuitry ensures compatibility with consumer DVD Technology Corp KINO 9452 Motherboard X X Q players m 48 pin LQFP Green package m Meets Microsoft WHQL WLP 2 x audio requirements m EAX
44. key Save all the CMOS changes only for Main Menu Table 5 1 BIOS Navigation Keys 5 1 3 Getting Help When F1 is pressed a small help window describing the appropriate keys to use and the possible selections for the highlighted item appears To exit the Help Window press Esc or the F1 key again 5 1 4 Unable to Reboot after Configuration Changes If the computer cannot boot after changes to the system configuration is made CMOS defaults Use the jumper described in Chapter 4 Section 4 5 1 5 1 5 BIOS Menu Bar The menu bar on top of the BIOS screen has the following main items Changes the basic system configuration Advanced Changes the advanced system settings m PCIPnP Changes the advanced PCI PnP Settings m Boot Changes the system boot configuration m Security Sets User and Supervisor Passwords m Chipset Changes the chipset settings m Exit Selects exit options and loads default settings The following sections completely describe the configuration options found in the menu items at the top of the BIOS screen and listed above 5 2 Main When the BIOS Setup program is entered the Main menu BIOS Menu 1 appears The Main menu gives an overview of the basic system information KINO 9452 Motherboard BIOS SETUP UTILITY System Time BIOS Menu 1 Main gt System Overview The System Overview lists a brief summary of different system components The fields in System Overview cannot
45. preceding License Agreement If you choose No the setup will close To install Intel R Chipset Software Installation Utility you must accept this agreement InstallShield lt Back Yes No Figure 6 3 License Agreement Step 5 Agree to the license terms by clicking YES The Readme in Figure 6 4 appears Readme Information Readme txt EEE EE Product Intel R Chipset Software Installation Utility Release Production Version Version 6 0 1 1002 Target Chipset Intel R E7520 amp Intel R 915G P GV Date May 07 2004 NOTE For the list of supported chipsets please refer to the Release Notes E 2 InstallShield Figure 6 4 Readme Information Step 6 Click YES The driver is installed on the computer After the installation is complete the installation complete screen shown in Figure 6 5 appears Select the preferred option and click FINISH to complete the installation process Page 134 Technology Corp KINO 9452 Motherboard InstallShield R Wizard Complete The InstallShield R Wizard has successfully installed Intel R Chipset Software Installation Utility Before you can use the Program you must restart your computer C No will restart my computer later Remove any disks from their drives and then click
46. selected with a maximum transfer rate of 16 6MBps This setting generally works with all hard disk drives manufactured after 1999 For other disk drives such as IDE CD ROM drives check the specifications of the drive gt DMA Mode Auto The DMA Mode BIOS selection adjusts the DMA mode options gt DEFAULT BIOS auto detects the mode Use this value if the IDE disk drive support cannot be determined S M A R T Auto Self Monitoring Analysis and Reporting Technology SMART feature can help predict impending drive failures The S M A R T BIOS option enables or disables this function gt Auto DEFAULT BIOS to auto detects if the hard disk drive supports S M A R T Use this setting if the IDE disk drive support cannot be determined Technology Corp KINO 9452 Motherboard M M Disabled Select this value to prevent the BIOS from using the SMART feature gt Enabled Select this value to allow the BIOS to use the SMART feature on support hard disk drives 32Bit Data Transfer Enabled The 32Bit Data Transfer BIOS option enables or disables 32 bit data transfers Disabled Prevents the BIOS from using 32 bit data transfers gt Enabled DEFAULT Allows BIOS to use 32 bit data transfers on support hard disk drives 5 3 3 Super IO Configuration The Super IO Configuration menu BIOS Menu 6 sets or ch
47. the Allocate IRQ to PCI VGA option to restrict the system from giving the VGA adapter card an interrupt address gt Yes DEFAULT Assigns IRQ to a PCI VGA if card requests IRQ gt No Does not assign IRQ to a VGA card even if the card requests an IRQ Palette Snooping Disabled Use the Palette Snooping option to enable or disable the palette snooping function gt Disabled DEFAULT Unless the VGA card manufacturer requires palette Page 111 KINO 9452 Motherboard snooping to be enabled this option should be disabled Enabled PCI devices are informed that an ISA based Graphics device is installed in the system so the ISA based Graphics card functions correctly This does not necessarily indicate a physical ISA adapter card The graphics chipset can be mounted on a PCI card Always check with the adapter card manual first before modifying the default settings in the BIOS PCIIDE BusMaster Enabled Use the PCI IDE BusMaster BIOS option to enable or prevent PCI IDE busmastering gt Disabled Busmastering is prevented gt Enabled DEFAULT IDE controller on the PCI local bus has mastering capabilities OffBoard IDE Card Auto Use the OffBoard PCI ISA IDE Card BIOS option to select the OffBoard PCI ISA IDE Card gt Auto DEFAULT The location of the Off Board PCI IDE adapter card is automatically detected by the AMIBIOS gt PCI Slot 1 PCI Slot 1 is selected a
48. 00MHz 533MHz or 667MHz of DDR2 memory m Comes with dual Broadcom BCM5787 for PCle GbE m Supports two SATA II channels with transfer rates up to 3 0Gb s Technology Corp KINO 9452 Motherboard MMM m Supports eight USB 2 0 devices m Supports HDTV Out dual 18 channel LVDS and CRT 1 2 KINO 9452 Board Overview NB Fan DDR2 DIMM Lop Sockets CPU Fan Back Front Power Light Panel t 3 IDE USB 2 0 PCI slot COM Ports SPDIF GPIO Mini PCI slot Keyboard Front Panel Mouse Audio LANs amp SerialPort LVDS UsBs Audio Jacks amp VGA Figure 1 1 KINO 9452 Board Overview Top View 1 2 1 KINO 9452 Connectors The KINO 9452 has the following connectors on board 2x DDR2 DIMM sockets m 1 x Digital connector m Fan connectors m 1 x Front panel audio connector m 1x Front panel connector KINO 9452 Motherboard m 1 IDE Interface connector m 1 x LCD backlight connector m 1xLVDSLCD connector m 1 x Mini PCI slot m x PCI slot m 1 Power connector m 3x Serial port connectors m 2 x SATA II connectors m 1 SPDIF connector m 2 x USB connectors The KINO 9452 has the following connectors on the board rear panel m 6 x Audio jacks m 1 CRT connector m 2 Ethernet connectors m 1 Keyboard Mouse connector m 1 Serial port connector m 1x TV Out port m 4x USB 2 0 p
49. 1 0 amp 2 0 compatible m Direct Sound 3D compatible m A3D compatible m 13012 compatible m 3D Positional Audio m Emulation of 26 sound environments to enhance gaming experience m 10 Band Software Equalizer m Voice Cancellation and Key Shifting in Karaoke mode m Realtek Media Player m Enhanced Configuration Panel to improve user experience m Microphone Acoustic Echo Cancellation AEC Noise Suppression NS and Beam Forming BF technology for voice application m ALC883D features optional Dolby Digital Live output for consumer equipment m ALC883DTS features optional DTS Connect software 2 16 Power Consumption Table 2 2 shows the power consumption parameters for the KINO 9452 when an Intel Core Duo processor with a clock speed of 2 16GHz is running with two DDR2 1GB DIMM modules Voltage Current 5V 1 58A 12V 2 05A 3 3V 3 12A 5VSB 0 32A Table 2 2 Power Consumption KINO 9452 Motherboard 2 17 Packaged Contents and Optional Accessory Items 2 17 1 Package Contents The KINO 9452 is shipped with the following components m 1xKINO 9452 single board computer m 1x IDE flat cable m 2xSATAcables m 1 x SATA power cable m 2 x RS 232 cables m 1 HDTV out cable m 1 1 shielding m 1 Mini jumper pack m 1x Utility CD m 1x Quick Installation Guide 2 17 2 Optional Accessory Items The items shown in the list below are optional accessory items are pur
50. 2 0 ports The USB ports are used for bus expansion Page 54 Technology Corp KINO 9452 Motherboard USB5 2 USB4 img Figure 3 15 Internal USB Connector Locations PIN DESCRIPTION PIN NO DESCRIPTION 1 vcc 2 GND 3 DATAO 4 DATA1 5 DATAO 6 DATA1 7 GND 8 VCC Table 3 17 USB3 and USB4 Pinouts 3 3 External Interface Connectors The peripheral connectors on the back panel are connected to devices externally when the KINO 9452 is installed in a chassis The peripheral connectors on the rear panel are m 6 x Audio jacks m 1 x CRT connector m 2 x RJ 45 Ethernet connectors m 1 Keyboard mouse connector KINO 9452 Motherboard m 1 Serial port connector m 1 TV Out connector m 4x USB 2 0 connectors 1 2 3456 7 9 8 Figure 3 16 KINO 9452 External Interface Connectors 3 3 1 Audio Connectors CN Label AUDIO1 CN Type Audio jack CN Location See Figure 3 16 labeled number 7 CN Pinouts See Figure 3 17 m Center Subwoofer port Yellow Connects the center subwoofer speakers m Line In port Light Blue Connects a CD ROM DVD player or other audio devices m Rear Speaker Out port Black Connects the rear speakers 4 6 8 channel audio configuration m Line Out port Lime Connects a headphone or a speake
51. 52 Dimensions mm Technology Corp o KINO 9452 Motherboard 2 2 2 External Interface Panel Dimensions External interface panel dimensions are shown in Figure 2 2 43 92 Figure 2 2 External Interface Panel Dimensions mm 2 3 CPU Support Table 2 1 lists the CPUs supported by the KINO 9452 board Model Clock Speed L2 Cache Max FSB Socket Intel Core 2 Duo 1 66 to 2 33 GHz 2MB 4MB 667 MHz 479 Intel Core Duo 1 20 to 2 33 GHz 2 667 MHz 479 Intel Core Solo 1 06 to 1 83 GHz 2 667 MHz 479 Table 2 1 Supported CPUs 2 3 1 Intel Core 2 Duo The Intel Core 2 Duo processor comes with the following features Dualcore processor with enhanced performance m Intel 64 architecture m Supports Intel Architecture with Dynamic Execution m On die primary 32 kB instruction cache and 32 kB write back data cache per core m up to 4 MB second level shared cache with Advanced Transfer Cache Architecture m Data Prefetch Logic KINO 9452 Motherboard 667 MHz Source Synchronous FSB for Standard Voltage processors Advanced Power Management features including Enhanced Intel SpeedStep Technology m Intel Enhanced Deeper Sleep state and Dynamic Cache Sizing 2 3 2 Intel Core Duo The Intel Core Duo processor comes with the following features m Two complete execution cores one processor package provide advan
52. 52 Motherboard DVMT Mode Select DVMT Mode Use the DVMT Mode Select option to select the Intel Dynamic Video Memory Technology DVMT operating mode gt Fixed Mode A fixed portion of graphics memory is reserved as graphics memory gt DVMT Mode DEFAULT Graphics memory is dynamically allocated according to the system and graphics needs gt Combo Mode A fixed portion of graphics memory is reserved as graphics memory If more memory is needed graphics memory 15 dynamically allocated according to the system and graphics needs gt DVMT FIXED Memory 128MB Use the DVMT FIXED Memory option to specify the maximum amount of memory that can be allocated as graphics memory This option can only be configured for if DVMT Mode or Fixed Mode is selected in the DVMT Mode Select option If Combo Mode is selected the maximum amount of graphics memory is 128MB Configuration options are listed below m 64MB m 128MB DEFAULT m Maximum DVMT Boot Display Device Auto Use the Boot Display Device option to select the display device used by the system when it boots Configuration option is listed below Auto DEFAULT Page 126 Technology Corp KINO 9452 Motherboard 4 Flat Panel 640 480 Use the Flat Panel Type option to select the type of flat panel connected to the system Configuration options a
53. 883HD WIN directory in the location browsing window where X is the system CD drive Figure 6 18 Step 9 Click OK to continue The driver is installed Step 1 The confirmation screen offers the option of restarting the computer now or later For the settings to take effect the computer must be restarted Click FINISH to restart the computer 6 6 Intel Matrix Storage Manager Installation To install the Intel Matrix Storage Manager driver please follow the steps below Step 1 Insert the Utility CD that came with the motherboard into the system CD drive Step 2 Open the X 5 SATA ICH7R directory and double click the iata60_cd exe installation file 147 KINO 9452 Motherboard Step 3 The Preparing Setup window appears Intel R Matrix Storage Manager Setup Setup Status Intel R Matrix Storage Manager Setup is performing the requested operations Installing 29 InstallShield Figure 6 25 Preparing Setup Screen Step 4 A Welcome screen appears Click NEXT to continue the installation Step 5 A license agreement appears Read through the license agreement Step 6 The Uninstallation Warning window appears Click on the NEXT button to continue Step 7 Accept the terms and conditions stipulated in the license agreement by clicking the YES button Step 8 The Choose Destination Location window appears Click on the NEXT button to continue By default all installed file
54. CD 2 VE DATA RXD TRANSMIT DATA TXD 60 ipie Technology Corp KINO 9452 Motherboard DATA TERMI READY anD m DATA SET READY DSR REQUEST TO SEND RTS 8 CLEAR TO SEND CTS 9 RING INDICATOR RI Table 3 22 External Serial Port Pinouts 3 3 6 TV Out Connector CN Label TV CN Type 7 pin TV port CN Location See Figure 3 16 labeled number 8 CN Pinouts See Table 3 23 The TV Out port connects to a TV Figure 3 22 TV Out Connector PN Description S Vidio Luminance Component Luminance Y S Vidio Chrominance Component Chrominance Pr KINO 9452 Motherboard Table 3 23 TV Out Pinouts 3 3 7 USB Connector CN Label LAN USB1B and LAN USB2B CN Type USB port CN Location See Figure 3 16 labeled number 3 and 5 Pinouts See Table 3 24 USB devices can be connected directly to the USB connectors on the rear panel DESCRIPTION PIN NO DESCRIPTION 3 me Table 3 24 External USB Connector Pinouts Page 62 IEI Technology Corp KINO 9452 Motherboard Chapter 4 Installation and Configuration 63 KINO 9452 Motherboard 4 1 Anti static Precautions Electrostatic discharge ESD can cause serious damage to electronic components including the KINO 9452 Dry climates are especially s
55. CPU FAN1 Fan connector System 3 pin header SYS FAN1 Fan connector Northbridge 3 pin header NB Front panel connector 14 pin header F PANEL1 Front panel audio connector 10 pin header AUDIO2 Digital Input Output connector 10 pin header DIO1 IDE Interface connector 40 pin header IDE1 LCD backlight connector 6 pin header CN1 LVDS LCD connector 30 pin header LVDS1 Mini PCI slot 124 pin Mini PCI Type slot MINIPCI PCI slot 124 pin PCI slot PCI2 Power connector 20 pin connector PWR1 Serial port connector 1 14 pin header COM2 Serial port connector 2 10 pin header COM3 Serial port connector 3 10 pin header COM4 SATA drive connector 1 7 pin SATA connector SATA1 SATA drive connector 2 7 pin SATA connector SATA2 SPDIF connector 5 pin header SPDIF1 USB connector 1 8 pin header USB4 USB connector 2 8 pin header USB5 Table 3 1 Peripheral Interface Connectors KINO 9452 Motherboard 3 1 3 Rear Panel Connectors Table 3 2 lists the rear panel connectors on the KINO 9452 Detailed descriptions of these connectors can be found in Section 3 3 Connector Type Label Audio Jacks Audio connector AUDIO1 CRT connector 15 pin female connector CRT COM1 Ethernet connector 1 RJ 45 connector LAN USB1A Ethernet connector 2 RJ 45 connector LAN USB2A Keyboard Mouse connector 6 pin mini din connector KBMS1 Serial port connector DB 9 male connector CRT COM1 TV Out port 7 pi
56. Clear CMOS Jumper Settings The clear CMOS jumper is located in Figure 4 10 4 5 2 COM2 Mode Selection Jumper Label JP1 Jumper Type 3 pin header Jumper Settings See Table 4 4 Jumper Location See Figure 4 10 This jumper configures the COM2 connector as an RS 232 serial port or an RS 422 RS 485 serial port The selection options are shown in Table 4 4 Table 4 4 JP1 Jumper Settings KINO 9452 Motherboard 4 5 3 LVDS LCD Voltage Selection WARNING Making the wrong setting on this jumper may cause irreparable damage to both the motherboard and the LCD screen connected to the onboard connector Jumper Label JP2 Jumper Type 6 pin header Jumper Settings See Table 4 5 Jumper Location See Figure 4 10 This jumper allows the user to set the voltage for the LCD panel Before setting this jumper please refer to the LCD panel user guide to determine the required voltage After the required voltage is known make the necessary jumper setting in accordance with the settings shown in Table 4 5 Gm mw RN Table 4 5 JP2 Jumper Settings 4 6 Chassis Installation After the CPU the cooling kit and the DIMM modules have been installed and after the internal peripheral connectors have been connected to the peripheral devices and the jumpers have been configure the motherboard can be mounted into chassis To mount the motherboard into a chassis please refer to the chassis user guide that ca
57. D option to determine if the system uses the SPD Serial Presence Detect EEPROM to configure the DRAM timing The SPD EEPROM contains all necessary DIMM specifications including the speed of the individual KINO 9452 Motherboard components such as CAS and bank cycle time as well as valid settings for the module and the manufacturer s code The SPD enables the BIOS to read the spec sheet of the DIMMs on boot up and then adjust the memory timing parameters accordingly gt Disabled DRAM timing parameters are manually set using the DRAM sub items gt Enabled DEFAULT DRAM timing parameter are set according to the DRAM Serial Presence Detect SPD If the Configure DRAM Timing by SPD option is disabled the following configuration options appear m DRAM CAS Latency 3 DRAM RAS to CAS Delay 5 DRAM Clocks DRAM RAS Precharge 5 DRAM Clocks DRAM RAS Activate to Precha 15 DRAM Clocks gt Memory Hole Disabled Use the Memory Hole option to reserve memory space between 15MB and 16MB for ISA expansion cards that require a specified area of memory to work properly If an older ISA expansion card is used please refer to the documentation that came with the card to see if it is necessary to reserve the space gt Disabled DEFAULT Memory is not reserved for ISA expansion cards gt 15 16 Between 15 and 16MB of memory is reserved for ISA expansion cards Boots Graphics Adapter Priority P
58. EG PCI Use the Boots Graphics Adapter Priority option to select the graphics controller used as the primary boot device Select either an integrated graphics controller IGD or a combination of PCI graphics controller a express PEG controller or an IGD Configuration options are listed below 124 Technology Corp KINO 9452 Motherboard M Y m IGD m PCI PEG m PEG IGD m PEG PCI DEFAULT Internal Graphics Mode Select Enable 8MB Use the Internal Graphic Mode Select option to specify the amount of system memory that can be used by the Internal graphics device gt Disable gt Enable 1MB 1MB of memory used by internal graphics device gt Enable 8MB DEFAULT 8MB of memory used by internal graphics device gt PEG Port Auto Use the PEG Port option to enable or disable the PCI Express port gt Auto DEFAULT BIOS auto detects the installed PEG cards gt Disabled Installed PEG cards cannot function Force X1 Disabled Use the PEG Force x1 option to convert a PCI express X16 slot into PCI express 1 slot gt Enabled PCI express X16 slot runs in PCI express X1 mode gt Disabled DEFAULT PCI express X16 slot runs in normal mode 5 7 1 1 Video Function Configuration Use the Video Function Configuration menu to configure the video device connected to the system Page 125 KINO 94
59. Finish to complete setup lt Back Cancel Figure 6 5 Restart the Computer 6 3 VGA Driver To install the VGA driver please follow the steps below Step 1 Insert the Utility CD that came with the motherboard into the system CD drive Step 2 Open the X 2 VGAWIN2K XP directory where is the system CD drive and double click the win2k xp1420 exe installation file Step 3 The Starting Install Shield Wizard appears Figure 6 6 Page 135 KINO 9452 Motherboard InstallShield R Wizard Production Version Releases Microsoft Windows 2000 Microsoft Windows Driver Revision 6 14 10 4543 26650 Production Version 14 20 0 4543 March 27 2006 NOTE This document refers to systems containing e Following Intel chipsets Intel R 910GL Express Chipset a 5 OX X Figure 6 6 Starting Install Shield Wizard Screen Step 4 The Preparing Setup window appears next Figure 6 7 Intel R Chipset Graphics D are InstallShield R Wizard Extractiag Files The contents of this package are being extracted Please wait while the InstallShield R Wizard extracts the files needed to install Intel R Chipset Graphics Driver Software on your computer This may take a Few moments Reading contents of package puc Installshield Figure 6 7 Preparing Setup Screen Step 5 Welcome sc
60. IEI Technology Corp User Manual Rev 1 0 September 2006 KINO 9452 Motherboard MM ee REVISION HISTORY Title KINO 9452 Intel Core Duo Core Solo Motherboard Revision Number Description Date of Issue 1 0 Initial release September 2006 COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability design and function and does not represent a commitment on the part of the manufacturer In no event is the manufacturer liable for direct indirect special incidental or consequential damages arising out of the use or inability to use the product or documentation even if advised of the possibility of such damages This document contains proprietary information protected by copyright All rights are reserved No part of this manual may be reproduced by any mechanical electronic or other means in any form without prior written permission of the manufacturer TRADEMARKS IBM PC is a registered trademark of International Business Machines Corporation INTEL is a registered trademark of INTEL Corporation AMI is registered trademarks of American Megatrends Inc Other product names mentioned herein are used for identification purposes only and may be trademarks and or registered trademarks of their respective owners KINO 9452 Motherboard Table of Contents T INTRODUGCTTON 15 Del KINO 9452 OVERV
61. IEW Jr a 16 TU KINO 9452 Benefits LAS PET 16 AMI y EUN 16 1 2 KINO 9452 BOARD OVERVIENW 17 PZT KINO 9452 COICO cesa a pb patr ate ua 17 1 2 2 Technical 18 2 DETAILED SPECIFICATIONS scccscceaversivcaasceusconsieescvanscoanesancauccanveadesnedabe CH ace Voci 21 FAR IUIS M 22 22 DIMENSIONS 22 2 2 1 Board Dimensions viccesre riie RET E ESEE E EEES 22 2 2 2 External Interface Panel Dimensions 23 2 3 CPU SUPPORT e a Eene 23 2 3 1 Intel Core Duo 23 2 3 2 Core a 24 2 4 ON BOARD CHIPSETS 25 2 4 1 Northbridge and Southbridge Chipset cesses eene 25 2 4 2 Intel 945GM Northbridge Chipset eus esi 25 243 Intel ICH7 M Southbridge 26 2 GRAPHICS SUPPORT c 26 2 0 MEMORY SUPPORT pH 27 2 7 PCI BUS INTERFACE SUPPORT 27 2 8 GBE ETHERNET m 27 DRIVE INTERFACE S EAE E 28 2 9 T SATA Drives creissien ES 28 28 2 10 SERIAL PORTS 29 2 1 REALE TIME
62. IO DRIVER ALC883 INSTALLATION ccce 143 6 6 INTEL MATRIX STORAGE MANAGER eere 147 A BIOS CONFIGURATION OPTIONS esset eee eese 151 BIOS CONFIGURATION OPTIONS 2 dug ed psa dapi 152 WATCHDOG TIMER 156 KINO 9452 Motherboard C ADDRESS nnne t en tnnn sese ses eese tensa sese assess ses 160 IO ADDRESS MAP eis eerie rv tet eaaet 161 C 2 1ST MB MEMORY ADDRESS 161 IRQ MAPPING s pos ton beni ita en tlic innu inde t ee 162 DMA CHANNEL ASSIGNMENTS sssecsccccecccscessenensccecececessssenscccesecescesssnsnaceeeeeeens 162 KINO 9452 Motherboard _ 2 List of Figures Figure 1 1 KINO 9452 Board Overview Top View eere 17 Figure 2 1 KINO 9452 Dimensions 22 Figure 2 2 External Interface Panel Dimensions mm 23 Figure 3 1 Connector and Jumper Locations 34 Figure 3 2 Fan Connector Locations eeeeeeeeenee enne nnns 37 Figure 3 3 Front Panel Audio Connector
63. MJ 4 8PMJ 8 LED2_YELP AD 30 AD 27 3 3V AD 25 AD 28 RESERVED AD 26 C BE 3 LN AD 24 AD 23 IDSEL GROUND GROUND AD 21 AD 22 AD 19 AD 20 GROUND PAR AD 17 AD 18 C BE 2 AD 16 GNT Table 3 11 Mini PCI Slot Pinouts IRDY Ground KINO 9452 Motherboard NAME PIN NAME 3 3V FRAME CLKRUN TRDY SERR STOP GROUND 3 3V PERR DEVSEL C BE 1 GROUND AD 14 AD 15 GROUND AD 13 AD 12 AD 11 AD 10 GROUND GROUND AD 09 AD 08 C BE O AD 07 3 3V 3 3V AD 06 AD 05 AD 04 RESERVED 94 95 96 97 98 99 AD 02 em ww _ ww _ KINO 9452 Motherboard 3 2 9 Power Connector Label PWR1 CN Type 20 pin connector CN Location See Figure 3 10 CN Pinouts See Table 3 12 This 20 pin power connector supports the ATX power supply PWR1 u 20 101 PIN NO DESCRIPTION PIN NO DESCRIPTION 1 3 3V 11 3 3V 2 3 3V 12 12V 3 GND 13 GND Page 48 IEI Technology Corp KINO 9452 Motherboard M9 PIN NO DESCRIPTION PIN NO DESCRIPTION 4 45V 14 PS ON 5 GND 15 GND 6 5V 16 GND 7 GND 17 GND 8 Power good 18 5V 9 5VSB 19 5V 10
64. PCI slot One PCI slot Super I O ITE8712 Digital I O 8 bit digital I O 4 input 4 output by super Audio REALTEK ALC883 with 7 1 channel HD interface with 2 audio streams support KINO 9452 Motherboard Ethernet Dual Broadcom BCM5787 for PCI Express GbE with ASF2 0 remote control support BIOS AMI BIOS Label Power ATX power Physical Dimensions 170mm x 170mm width x length Operating Minimum 0 32 F Temperature Maximum 60 C 140 F Table 1 1 Technical Specifications Page 20 IEI Technology Corp KINO 9452 Motherboard Chapter 2 Detailed Specifications Page 21 KINO 9452 Motherboard 2 1 Overview board features of the KINO 9452 in This chapter describes the specifications and on detail imensions 2 2D 1 Board Dimensions 2 2 The dimensions of the board are shown in Figure 2 1 699000000 Donn nan OO AA CONS OO AAAA Sevevvesuye vec oy M AUD Ie sec we sev IVY TOOL 4 296902 on vac ous TROC TEC TY 807 lt Figure 2 1 94
65. S is preprogrammed into the ROM BIOS The BIOS setup program allows users to modify the basic system configuration This chapter describes how to access the BIOS setup program and the configuration options that may be changed 5 1 1 Starting Setup The AMI BIOS is activated when the computer is turned on The setup program can be activated in one of two ways 1 Press the DELETE key as soon as the system is turned on or 2 Press the DELETE key when the Press Del to enter SETUP message appears on the screen If the message disappears before restart the computer and try again 5 1 2 Using Setup Use the arrow keys to highlight items press ENTER to select use the and keys to change entries press F1 for help and press Esc to quit Navigation keys are shown in Key Futon Up arrow Move to previous item Down arrow Move to next item Left arrow Move to the item on the left hand side Right arrow Move to the item on the right hand side Esc key Main Menu Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu Exit current page and return to Main Menu key Increase the numeric value or make changes key Decrease the numeric value or make changes F1 key General help only for Status Page Setup Menu and Option Page Setup Menu Technology Corp KINO 9452 Motherboard F2 F3 key Change color from total 16 colors F2 to select color forward F10
66. T applies zl Y ou must accept all of the terms of the license agreement in order to continue the setup program Do you accept the terms lt Back no Intel R Installation Frameworks Figure 6 9 VGA Driver License Agreement Step 7 Accept the terms and conditions stipulated in the license agreement by clicking Page 137 KINO 9452 Motherboard the YES button Figure 6 9 The installation notice shown in Figure 6 10 appears Installing version 6 14 10 4497 Figure 6 10 VGA Driver Installing Notice Step 8 After the driver installation process is complete a confirmation screen shown in Figure 6 11 appears The setup for the Intel R Graphics Media Accelerator Driver is complete You must restart this computer for the changes to take effect Would you like to restart the computer now 6 Yes want to restart my computer now will restart my computer later Remove any disks from their drives and then click Finish lt Back Intel Fi Installation Frameworks Figure 6 11 VGA Driver Installation Complete Step 9 The confirmation screen shown in Figure 6 11 allows user to restart the computer immediately after the installation is complete or to restart the computer later For the settings to take effect the computer must be restarted Once decided when to restart the computer click the FINISH button Page 138 Technology Corp KINO 9452 Mo
67. TR sleep state The CPU has no power RAM is in slow refresh the power supply is in a reduced power mode 5 3 6 APM Configuration Use the APM Configuration menu BIOS Menu 10 to select the advanced power management BIOS SETUP UTILITY Power Management APM Enabled BIOS Menu 10 APM Configuration Power Management APM Enabled The Power Management APM BIOS option accesses the advanced power management features gt Disabled Disables the Advanced Power Management APM Page 100 echnology Corp KINO 9452 Motherboard M MM M M feature gt Enabled DEFAULT Enables the APM feature Restore AC Power Loss by IO Power The Restore on AC Power Loss by IO BIOS option specifies what state the system returns to if there is a sudden loss of power to the system gt Power Off DEFAULT system remains turned off gt Power On The system turns on Power Button Mode On Off The Power Button Mode BIOS specifies how the power button functions gt On Off DEFAULT When the power button is pressed the system is either turned on or off Resume on Ring Disabled The Resume on Ring BIOS option specifies if the system will be roused from a suspended or standby state when there is activity on the RI ring modem line That is the system will be roused by an incoming call on a modem gt Disabled DEFAULT Wake event not generated by an
68. anced r Hardware Wizard The Hardware wizard helps you install uninstall repair unplug eject and configure your hardware Hardware Wizard Device Manager The Device Manager lists all the hardware devices installed on your computer Use the Device Manager to change the properties of any device Driver Signing i Hardware Profiles Hardware profiles provide a way for you to set up and store different hardware configurations Hardware Profiles Figure 6 21 Double Click the Device Manager Tab Step 4 Alist of system hardware devices appears Figure 6 15 144 IEI Technology Corp KINO 9452 Motherboard MH M Computer Disk drives Display adapters 09 2 DVD CD ROM drives aS Floppy disk controllers f y Human Interface Devices IDE ATA ATAPI controllers 9 8 Keyboards E Mice and other pointing devices Monitors 1 89 Network adapters 9 19 Ports COM amp LPT m Sound video and game controllers 28 System devices Universal Serial Bus controllers Figure 6 22 Device Manager List Step 5 Double click the listed device that has question marks next to it This means Windows does not recognize the device Step 6 The Device Driver Wizard appears Figure 6 16 Click NEXT to continue Page 145 KINO 9452 Motherboard Upgrade Device Driver Wizard
69. anges the configurations for the FDD controllers parallel ports and serial ports BIOS SETUP UTILITY Serial Port1 Address BIOS Menu 6 Super IO Configuration KINO 9452 Motherboard Serial Port1 Address 3F8 IRQ4 The Serial Port1 Address option allows BIOS to select the Serial Port 1 base address gt Disabled No base address is assigned to Serial Port 1 gt 3F8 IRQ4 DEFAULT Serial Port 1 I O port address is 3F8 and the interrupt address is IRQ4 gt 3E8 IRQ4 Serial Port 1 I O port address is 3E8 and the interrupt address is IRQ4 gt 2E8 IRQ3 Serial Port 1 port address is 2E8 and the interrupt address is IRQ3 Serial Port Mode Normal Allows BIOS to select the mode for Serial Port 1 gt Normal DEFAULT Serial Port 1 mode is normal gt IrDA Serial Port 1 mode is IrDA gt ASKIR Serial Port 1 mode is ASK IR Serial Port2 Address 2F8 IRQ3 The Serial Port2 Address option allows BIOS to select the Serial Port 2 base address gt Disabled No base address is assigned to Serial Port 2 gt 2F8 IRQ3 DEFAULT Serial Port 2 port address is 3F8 and the interrupt address is IRQ3 gt 3E8 IRQ4 Serial Port 2 I O port address is 3E8 and the interrupt address is IRQ4 2E8 IRQ3 Serial Port 2 I O port address is 2E8 and the interrupt address is IRQ3 Page 94 IEI Technology Corp KINO 9452 Motherboard _ _ Serial Port2 Mode Normal Allows BIOS
70. ash BIOS used are listed below SMIBIOS DMI compliant m Console redirection function support m PXE Pre Boot Execution Environment support m USB booting support 2 14 Operating Temperature and Temperature Control The maximum and minimum operating temperatures for the KINO 9452 are listed below wm Minimum Operating Temperature 0 C 32 F m Maximum Operating Temperature 60 C 140 F A cooling fan and heat sink must be installed on the CPU Thermal paste must be smeared on the lower side of the heat sink before it is mounted on the CPU Heat sinks are also mounted on the northbridge and southbridge chipsets to ensure the operating temperature of these chips remain low KINO 9452 Motherboard 2 15 Audio Codec The KINO 9452 has an integrated REALTEK ALC883 CODEC The ALC883 CODEC is a Value 7 142 Channel High Definition Audio HDA codecs The ALC883 series provide 10 DAC channels that simultaneously support 7 1 sound playback plus 2 channels of independent stereo sound output multiple streaming through the front panel stereo output Some of the features of the codec are listed below High performance DACs with 95dB SNR A Weighting ADCs with 85dB SNR A Weighting m Meets performance requirements for audio on PC2001 systems and Microsoft WLP 2 x Ten DAC channels support 16 20 24 bit PCM format for 7 1 sound playback plus 2 channels of independent stereo sound output multiple streaming through the
71. be changed The items shown in the system overview include AMI BIOS Displays auto detected BIOS information Version Current BIOS version Build Date Date the current BIOS version was made ID Installed BIOS ID m Processor Displays auto detected CPU specifications Type Names the currently installed processor Speed Lists the processor speed O Count The number of CPUs on the motherboard m System Memory Displays the auto detected system memory O Size Lists memory size The System Overview field also has two user configurable fields KINO 9452 Motherboard m System Time xx xx xx The system time is set here m System Date Day xx xx xxxx The system date is set here 5 3 Advanced The Advanced menu BIOS Menu 2 allows access to the CPU and peripheral device configuration options through the following sub menus WARNING Setting the wrong values in the sections below may cause the system to malfunction Make sure that the settings made are compatible with the hardware m CPU Configuration see Section 5 3 1 m IDE Configuration see Section 5 3 2 m SuperlO Configuration see Section 5 3 3 Hardware Health Configuration see Section 5 3 4 m ACPI Configuration see Section 5 3 5 m Configuration see Section 5 3 6 m MPS Configuration see Section 5 3 7 m Remote Access Configuration see Section 5 3 8 m USB Configuration see Sectio
72. cements in simultaneous computing Dual core processing efficiently delivers performance while balancing power requirements m Two execution cores share a high performance power optimized 667 MHz front side bus FSB to access the same chipset memory m Enhanced Intel SpeedStep technology allows a system to dynamically adjust processor voltage and core frequency decreasing average power consumption and average heat production m Intel Smart Cache Design allows two execution cores to share 2 MB of L2 cache reducing FSB traffic and enhancing system responsiveness m Intel Advanced Thermal Manager supports new digital temperature sensors and thermal monitors on each execution core to enhance thermal monitoring accuracy m Streaming SIMD Extensions SSE3 provides significant performance enhancement for multi media applications m Embedded lifecycle support protects system investment by enabling extended product availability for embedded and communications customers 2 3 3 Intel Core Solo The Intel Solo processor comes with the following features m Supports Intel Architecture with Dynamic Execution wm On die primary 32 KB instruction cache and 32 KB write back data cache 2 MB second level cache with Advanced Transfer Cache Architecture m Streaming SIMD Extensions 2 SSE2 and Streaming SIMD Extensions 3 SSE3 Technology Corp KINO 9452 Motherboard X X
73. chased separately m CPU cooler m USB cable m RS 232 422 485 cable Page 32 1 Technology Corp KINO 9452 Motherboard Chapter 3 Connectors and Jumpers Page 33 KINO 9452 Motherboard 3 1 Peripheral Interface Connectors Section 3 1 1 shows peripheral interface connector locations Section 3 1 2 lists all the peripheral interface connectors seen in Section 3 1 1 3 1 1 KINO 9452 Layout Figure 3 1 shows the on board peripheral connectors backplane peripheral connectors and on board jumpers DIMM2 DIMM1 CPU 8 8 FAN1 NB FAN1 i 5 USB4 ili COM4 TT COM3 a il MINIPCIMM 2 1 ax LVDS1 CRT COM1 AUDIO1 DIO1 KBMS1 ES c Figure 3 1 Connector and Jumper Locations 3 1 2 Peripheral Interface Connectors Table 3 1 shows a list of the peripheral interface connectors on the KINO 9452 Detailed descriptions of these connectors can be found in Section 3 2 Page 34 IEI Technology Corp KINO 9452 Motherboard M M MM 48 Connector Type Label DDR2 DIMM socket 240 pin slot DIMM1 DDR2 DIMM socket 240 pin slot DIMM2 Fan connector CPU 3 pin header
74. ctor supports one or two channel 18 or 36bit LVDS panel I 0555595555728 Cg d Q PIN NO DESCRIPTION PIN NO DESCRIPTION 1 GND 2 GND 3 1 LVDS data0 output 4 1 LVDS data0 output 5 1 LVDS data1 output 6 1 LVDS data1 output 7 1 LVDS data2 output 8 1 LVDS data2 output 9 1 LVDS clock output 10 1 LVDS clock output 11 NC 12 NC 13 GND 14 GND 15 2 LVDS data0 output 16 2 LVDS data0 output KINO 9452 Motherboard PIN NO DESCRIPTION PIN NO DESCRIPTION 17 2 LVDS data1 output 18 2 LVDS data1 output 19 2 LVDS data2 output 20 2 LVDS data2 output 21 2 LVDS clock output 22 2 LVDS clock output 23 NC 24 NC 25 GND 26 GND 27 LCD 3 3V 5V or 12V 28 LCD 3 3V 5V or 12V 29 LCD 3 3V 5V or 12V 30 LCD 3 3V 5V or 12V Table 3 10 LVDS LCD Connector Pinouts 3 2 8 Mini PCI Slot CN Label MINIPCI Type 124 pin Mini PCI Type slot CN Location See Figure 3 9 CN Pinouts See Table 3 11 Mini PCI is a small form factor version of a PCI card Mini PCI expansion devices can be inserted into the Mini PCI slot MINIPCI 12 Figure 3 9 Mini PCI Slot Location Technology Corp e me GROUND RESERVED GROUND 8P
75. d Configuration and Power Interface ACPI and Power Management APM options BIOS SETUP UTILITY ACPI Aware 0 5 BIOS Menu 8 ACPI Configuration ACPI Aware Yes Use the ACPI Aware O S option to enable the system to configure ACPI power saving options ACPI can only be implemented if the system OS complies with the ACPI standard Windows 98 Windows 2000 and Windows XP all comply with ACPI Page 98 echnology Corp KINO 9452 Motherboard M HMM M _ gt No Disables the ACPI support for the OS This selection should be disabled if the OS does not support ACPI gt Yes Enables the ACPI support for the operating system This selection should be enabled if the OS does support ACPI 5 3 5 1 General ACPI Configuration Use the General ACPI Configuration menu BIOS Menu 9 to select the ACPI state when the system is suspended BIOS SETUP UTILITY Suspend mode 53 1 BIOS Menu 9 General Configuration Advanced Configuration Suspend mode S3 STR Use the Suspend Mode option to specify the sleep state the system enters when it is not being used gt 1 POS The system enters S1 POS sleep state The system KINO 9452 Motherboard appears off The CPU is stopped RAM is refreshed the system is running in a low power mode gt 3 STR DEFAULT The system enters S3 S
76. e 24 bpp true color displays Panel Fitting Panning and Center Mode supported CPIS 1 5 compliant Spread spectrum clocking supported Panel Power Sequencing support Integrated PWM interface for LCD backlight inverter control m TV Out Three integrated 10 bit DACS MacroVision support Overscaling NTSC PAL Component S Video and Composite Output interfaces HDTV support 480 720 10801 1080 m SDVO Ports O Concurrent operation of x1 PCle with SDVO O Two SDVO ports supported O Supports appropriate external SDVO components DVI LVDS TV Out 2 6 Memory Support The KINO 9452 has two DDR2 DIMM sockets and supports two 400MHz 533MHz or 667MHz DDR2 DIMM with a maximum RAM of up to 2GB 2 7 PCI Bus Interface Support The PCI bus on the KINO 9452 has the following features m 33MHz Revision 2 3 is implemented m Six PCI REQ GNT pairs is available m 64 bit addressing on PCI using DAC protocol is supported 2 8 GbE Ethernet The BCM5787 is a seventh generation 10 100 1000BASE T Ethernet LAN controller solution for high performance network applications The device combines a triple speed 27 KINO 9452 Motherboard IEEE 802 3 compliant Media Access Controller MAC with a triple speed Ethernet transceiver PCle bus interface and on chip buffer memory in a single device The device is fabricated in a 1 2V CMOS process providing a low power system solution The GbE controller features are below m Integrated 10 100
77. ed the CPU should be easily inserted into the socket Step 4 Insert the CPU To insert the CPU into the socket hold the CPU by its edges and follow the instructions below Step 5 Correctly orientate the CPU with the IHS Integrated Heat Sink side facing upward Step 6 Locate the pin 1 mark on the CPU Step 7 Gently insert the CPU into the socket Step 8 Rotate the retention screw into the locked position See Figure 4 2 Technology Corp KINO 9452 Motherboard Pin 1 location v Figure 4 2 Lock the CPU Socket Retention Screw 4 4 2 Cooling Kit CF 479B RS Installation Figure 4 3 IEI CF 479B RS Cooling Kit IEI provides a cooling kit designed for socket 479 CPUs See Figure 4 3 The cooling kit is comprised of a CPU heat sink and a cooling fan A NOTE The CF 479B RS heat sink comes with a sprayed layer of thermal paste 69 KINO 9452 Motherboard Make sure the paste is not accidentally wiped during the unpacking or installation of the heat sink Thermal paste between the CPU and the heat sink is important for optimum heat dissipation To install the CF 479B RS cooling kit please follow the steps below Step 1 Place the cooling kit onto the CPU Make sure the CPU cable can be properly routed when the cooling kit is installed Step 2 Properly align the cooling kit Make sure its four spring screw fasteners can pass through the pre drilled holes on the PCB
78. edia Device Shift Keyed Infrared Advanced Technology Attachments Basic Input Output System Compact Flash Type 2 Complementary Metal Oxide Semiconductor Central Processing Unit Compressor Decompressor Serial Port Digital to Analog Converter Double Data Rate Dual Inline Memory Module Digital Input Output Direct Memory Access Enhanced IDE Enhanced Intel SpeedStep Technology Floppy Disk Drive Floppy Disk Connector Flexible File Input Output First In First Out Front Side Bus Infrared Data Association HDD Hard Disk Drive IDE Integrated Data Electronics Input Output ICH4 Controller Hub 4 L1 Cache Level 1 Cache L2 Cache Level 2 Cache LCD Liquid Crystal Display LPT Parallel Port Connector LVDS Low Voltage Differential Signaling MAC Media Access Controller OS Operating System PCI Peripheral Connect Interface PIO Programmed Input Output PnP Plug and Play POST Power On Self Test RAM Random Access Memory SATA Serial ATA S M A R T Self Monitoring Analysis and Reporting Technology SPD Serial Presence Detect S PDI Sony Philips Digital Interface SDRAM Synchronous Dynamic Random Access Memory SIR Serial Infrared UART Universal Asynchronous Receiver transmitter USB Universal Serial Bus VGA Video Graphics Adapter KINO 9452 Motherboard THIS PAGE IS INTENTIONALLY LEFT BLANK 14 IEI Technology Corp KINO 9452 Motherboard MM
79. ent ESD damage to the motherboard and other electronic components like the CPU and DIMM modules The following components must be installed onto the motherboard or connected to the motherboard during the installation process CPU m CPU cooling kit DDR2 memory modules m Peripheral device connection 4 4 1 CPU Installation A WARNING CPUs are expensive and sensitive components When installing the CPU please be careful not to damage it in anyway Make sure the CPU is installed properly and ensure that a heat sink and CPU cooling fan is properly installed before the motherboard is run or else both the CPU and the board may be damaged To install an Intel 479 pin CPU onto the motherboard follow the steps below Step 1 Is the CPU retention screw in an unlocked position When shipped the retention screw of the CPU socket should be in the unlocked position If it is not in the unlocked position use a screwdriver to position it in an unlocked position See Figure 4 1 KINO 9452 Motherboard Cut edge Figure 4 1 Make sure the CPU socket retention screw is unlocked Step 2 Inspect the CPU socket Make sure there are no bent pins and make sure the Socket contacts are free of foreign material If any debris is found remove it with compressed air Step 3 Correctly position the CPU Make sure the pin 1 mark matches the cut edge on the CPU socket Carefully place the CPU on top of the socket When properly plac
80. ented for configuration gt Enhanced If this option is selected Configure SATA as and Configure SATA channels options are presented for configuration Page 88 echnology Corp KINO 9452 Motherboard X X Q gt Legacy IDE Channels SATA PATA Sec Use the Legacy IDE Channels option configures PATA and SATA resources for operating systems that require legacy IDE operation gt SATA Only Enable up to two SATA devices gt Reserved The legacy IDE channels are reserved gt SATA Pri DEFAULT This option allows the system to access the SATA PATA Sec devices before the primary IDE devices gt Only Enable the two primary IDE devices Select this option only when the two primary IDE devices are available IDE Master and IDE Slave When entering setup BIOS auto detects the presence of IDE devices This displays the status of the auto detected IDE devices The following IDE devices are detected and are shown in the IDE Configuration menu m Primary IDE Master m Primary IDE Slave m Secondary IDE Master m Secondary IDE Slave The IDE Configuration menu BIOS Menu 4 allows changes to the configurations for the IDE devices installed in the system If an IDE device is detected and one of the above listed four BIOS configuration options are selected the IDE configuration options shown in Section 5 3 2 1 appear 5 3 2 1 IDE Mas
81. ey can be used for this operation Load Failsafe Defaults Use the Load Failsafe Defaults option to load failsafe default values for each of the parameters on the Setup menus F8 key can be used for this operation Page 130 Technology Corp KINO 9452 Motherboard Chapter 6 Software Drivers 131 KINO 9452 Motherboard 6 1 Available Software Drivers NOTE The content of the CD may vary throughout the life cycle of the product and is subject to change without prior notice Visit the IEI website or contact technical support for the latest updates The KINO 9452 motherboard has the following software drivers m Chipset Driver Installation m VGA Utilities Driver m LAN Driver for GbE LAN Installation m RealTek Audio Driver ALC883 Installation m SATA Driver Installation All drivers can be found on the CD that came with the motherboard To install the drivers please follow the instructions in the sections below 6 2 Chipset Driver Installation To install the chipset driver please follow the steps below Step 1 Insert the CD into the system that contains the KINO 9452 board Open the 1 INF directory and locate the icon for the infinst autol exe installation file Once located use the mouse to double click the icon Step 2 The InstallShield Wizard Preparation Screen in Figure 6 1 appears 132 Technology Corp KINO 9452 Motherboard
82. f the following optional search locations that you specify To start the search click Next If vou are searching on a floppy disk or CD ROM drive insert the floppy disk or CD before clicking Next ptional search locations disk drives I CO ROM dives Specify a location Figure 6 17 Locate Driver Files Step 8 Select the proper OS folder under the X 3 LAN BROADCOM BCM57xx Drivers directory Figure 6 18 in the location browsing window where is the system CD drive LL DOS NDIS2 8 28 7 11 C Linux bcm5700 8 3 14 Linux 53 3 43f BROADCOM 5 Netware 00116 8 27 Drivers 1052 NDIS2 8 28 E L48CO 8 32 SCO UnixWare 8 3 2 Solaris 86 86 64 EM64T 8 3 1 Windows 2000 8 48e Windows ME 98se 8 48e Windows Server 2003 32 bit 8 48e Windows Server 2003 1A464 8 48e Windows Server 2003 x86 64EM64T 8 48e Windows XP x86 64EM64T 8 48e WindowsNT4 8 48e WindowsXP 8 48 WindowsXP IA64 8 48 readme txt Figure 6 18 Location Browsing Window Page 142 Technology Corp KINO 9452 Motherboard Step 9 Click OK to continue A driver files location menu window appears Click NEXT to continue The driver is installed 6 5 RealTek HD Audio Driver ALC883 Installation To install the Realtek High Definition HD Audio driver please follow the steps below Step 1 Open Windows Co
83. id Memory Power Mgmt 2 4 3 Intel ICH7 M Southbridge Chipset The Intel ICH7 M southbridge chipset comes with the following features PCI Local Bus Specification Revision 2 3 support for 33 MHz PCI operations supports up to six Req Gnt pairs m ACPI Power Management Logic support m Enhanced controller interrupt controller and timer functions m Integrated Serial ATA host controller with independent DMA operation on two ports and AHCI m Integrated IDE controller supports Ultra ATA 100 66 33 m USB host interface with support for eight USB ports four UHCI host controller one EHCI high speed USB 2 0 Host controller m Supports Audio Codec 97 Revision 2 3 Specification m Supports Intel High Definition Audio m Supports Intel Matrix Storage Technology m Supports Intel Active Management Technology m Low Pint Count LPC interface m Firmware Hub FWH interface support m Serial Peripheral Interface SPI support 2 5 Graphics Support The graphics features listed below are all integrated on the Intel 945GM northbridge chipset m Analog CRT Integrated 400 MHz RAMDAC O Analog monitor support up to QXGA O Support for CRT hot plug m LVDS Page 26 IEI Technology Corp KINO 9452 Motherboard M Panel support up to UXGA 1600 x 1200 25 MHz 112 MHz single dual channel 2 18bpp TFT panel type supported Pixel Dithering for 18 bit TFT panel to emulat
84. incoming call gt Enabled Wake event generated by an incoming call Resume on PME Disabled The Resume on PME BIOS option specifies if the system will be roused from a suspended or standby state when there is activity on the PCI PME power management event controller gt Disabled DEFAULT Wake event not generated by PCI PME controller Page 101 KINO 9452 Motherboard activity Enabled Wake event generated by PCI PME controller activity gt Resume On Alarm Disabled The Resume On RTC Alarm determines when the computer will be roused from a suspended state gt Disabled DEFAULT The real time clock RTC cannot generate a wake event gt Enabled If selected the following will appear with values that can be selected RTC Alarm Date Days gt RTC Alarm Time After setting the alarm the computer will turn itself on from a suspend state when the alarm goes off Resume On PCI Express WAKEZ Enabled The Resume On PCI Express WAKE BIOS option specifies if the system will be roused from a suspended or standby state when there is activity on the PCI Express controller gt Disabled Wake event not generated by PCI Express controller activity gt Enabled DEFAULT Wake event generated by PCI Express controller activity 5 3 7 MPS Configuration Use the MPS Configuration menu BIOS Menu 11 to select multi processor table Page 102 Technology Corp KINO 9452
85. iodically refresh the Watchdog Timer However the Watchdog timer is disabled if the time out value is set to zero A tolerance of at least 1096 must be maintained to avoid unknown routines within the operating system DOS such as disk I O that can be very time consuming 157 KINO 9452 Motherboard When exiting a program it is necessary to disable the Watchdog Timer otherwise the system resets Example program INITIAL TI MER PERI OD COUNTER W LOOP MOV AX 6F02H setting the time out value MOV BL 30 time out value is 48 seconds INT 15H ADD THE APPLI CATI ON PROGRAM HERE 1 is the application over W LOOP No restart the application MOV AX 6F02H disable Watchdog Timer MOV BL 0 INT 15H Page 158 1 Technology Corp KINO 9452 Motherboard _ _ _ THIS PAGE IS INTENTIONALLY LEFT BLANK Page 159 KINO 9452 Motherboard Address Mapping Page 160 Technology Corp KINO 9452 Motherboard C 1 IO Address Map 000 01F DMA Controller 020 021 Interrupt Controller 040 043 System time 060 06F Keyboard Controller 070 07F System CMOS Real time Clock 080 09F DMA Controller 0A0 0A1 Interrupt Controller 0CO ODF DMA Controller OFO OFF
86. m voltages BIOS SETUP UTILITY CPU FAN Mode Setting Full On model BIOS Menu 7 Hardware Health Configuration Page 96 echnology Corp KINO 9452 Motherboard CPU Mode Setting Full On mode The CPU FAN Mode Setting has the following options gt Full mode DEFAULT f selected there are no additional configurable options gt Automatic If selected the following options will appear with Mode values that can be configured gt CPU Temp Limit of OFF CPU Temp Limit of Start CPU Temp Limit of Full CPU Fan Start PWM gt Slop PWM 1 0 1 PWM Default 2 PWM 4 PWM 8 PWM 16 PWM 32 PWM or 64 PWM gt PWM Manually If selected the following option will appear with mode values that can be configured Fan PWM Control The following system parameters and values are shown The system parameters that are monitored are m System Temperatures The following system temperatures are monitored CPU Temperature O System Temperature m Fan Speeds The CPU cooling fan speed is monitored CPU Fan Speed O System Fan Speed m Voltages The following system voltages are monitored O CPU Core 2 5V KINO 9452 Motherboard 3 30 45 00V 412 0V GMCH 1 5V 1 05V 5VSB VBAT O 5 3 5 Configuration Configuration menu BIOS Menu 8 configures the Advance
87. me with the product Technology Corp KINO 9452 Motherboard 4 7 Rear Panel Connectors 4 7 1 LCD Panel Connection The conventional CRT monitor connector is a 15 pin female D SUB connector Pin assignments can be seen in that can be connected to external monitors 4 7 2 Ethernet Connection The rear panel RJ 45 connectors can be connected to an external LAN and communicate with data transfer rates up to 1Gb s 4 7 3 USB Connection The rear panel USB connectors provide easier and quicker access to external USB devices The rear panel USB connector is a standard connector and can easily be connected to other USB devices 4 7 4 Serial Connection The rear panel serial connector COM1 provides easy and quick access to external serial devices 4 7 5 Keyboard and Mouse Connection A PS 2 keyboard and a PS 2 mouse can be connected to the appropriate PS 2 connector on the rear panel 4 7 6 Audio Interface Value 7 142 Channel High Definition Audio HDA signals are interfaced through the audio jack connectors The signals include microphone line in line in stereo Center Subwoofer speaker out rear speaker out and side speaker out KINO 9452 Motherboard THIS PAGE IS INTENTIONALLY LEFT BLANK 80 ipie Technology Corp KINO 9452 Motherboard Chapter 5 AMI BIOS Setup 81 KINO 9452 Motherboard 5 1 Introduction A licensed copy of AMI BIO
88. n 5 3 9 KINO 9452 Motherboard BIOS SETUP UTILITY CPU Configuration BIOS Menu 2 Advanced 5 3 1 CPU Configuration The CPU Configuration menu BIOS Menu 3 shows detailed CPU specifications and CPU configuration options 86 echnology Corp KINO 9452 Motherboard 9 BIOS SETUP UTILITY BIOS Menu 3 CPU Configuration The CPU Configuration menu BIOS Menu 3 lists the following CPU details Manufacturer Lists the name of the CPU manufacturer Brand String Lists the brand name of the CPU being used m Frequency Lists the CPU processing speed m FSB Speed Lists the FSB speed Cache L1 Lists the CPU L1 cache size Cache L2 Lists the CPU L2 cache size 5 3 2 IDE Configuration The IDE Configuration menu BIOS Menu 4 allows changes to the configurations for the IDE devices installed in the system KINO 9452 Motherboard BIOS SETUP UTILITY ATA IDE Configuration Compatible BIOS Menu 4 IDE Configuration Configuration Compatible The ATA IDE Configuration BIOS option allows the user to configure the ATA IDE device mode gt Disabled Disable all ATA IDE ports No Primary Secondary IDE mode is presented for configuration gt Compatible DEFAULT Up 4 HDDs can be used two for SATA and the other for PATA IDE If this option is selected Legacy IDE Channels option is pres
89. n TV port TV USB 2 0 port 1 USB port connector LAN USB1B USB 2 0 port 2 USB port connector LAN USB2B Table 3 2 Rear Panel Connectors 3 1 4 On board Jumpers Table 3 3 lists the on board jumpers Detailed descriptions of these jumpers can be found in Section 4 5 Description Label Type Clear CMOS JP3 3 pin header COM2 mode selection JP1 3 pin header LVDS LCD voltage selection JP2 6 pin header Table 3 3 On board Jumpers 36 IEI Technology Corp KINO 9452 Motherboard 4 3 2 Internal Peripheral Connectors Internal peripheral connectors are found on the motherboard and are only accessible when the motherboard is outside of the chassis This section has complete descriptions of all the internal peripheral connectors on the KINO 9452 3 2 1 Fan Connectors CN Label CPU FAN1 SYS 1 and NB FAN1 CN Type 3 pin header CN Location See Figure 3 2 Pinouts See Table 3 4 The cooling fan connectors on the KINO 9452 provide a 12V 500mA current to one CPU cooling fan one system cooling fan and one Northbridge cooling fan There is a sense pin in the fan connector which transfers the fan s sense signal to the system BIOS in order to recognize the fan speed Please note that only some specific types of fans offer a rotation signal NB 1 CPU
90. ntrol Panel Figure 6 12 New Office Document Open Office Document Set Program Access and Defaults D windows Update Program Updates Programs Documents Control Panel Settings M Network and Dial up Connections Printers m Taskbar amp Start Menu Search Help Run Log Off paulsharpe Figure 6 19 Access Windows Control Panel Step 2 Double click the System icon Figure 6 13 Page 143 KINO 9452 Motherboard Control Panel File Edit Favorites Tools gt Qisearch Gyrolders C4 06 GS X A Ed Address E Control Panel gt AutodeskPlot Autodesk Automatic Date Time Control Panel Style Manager X Plotter Updates Use the settings in Control Panel to GT a A personalize your computer Folder Options Fonts Game Intel R Select an item to view its description Controllers Extreme Windows Update lt D e Windows 2000 Support ES 9 Java Keyboard Mail Mouse Network and Phone and Power Options Printers Program Modem Updates ao Scanners and Scheduled Sounds and System Users and Cameras Tasks Multimedia Passwords 30 object s el My Computer P Figure 6 20 Double Click the System Icon Step 3 Double click the Device Manager tab Figure 6 14 System Properties General Network Identification Hardware User Profiles Adv
91. nu 13 to read USB configuration information and configure the USB settings BIOS SETUP UTILITY USB Functions 8 USB Ports BIOS Menu 13 USB Configuration gt USB Configuration The USB Configuration field shows the system USB configuration The items listed are Page 105 KINO 9452 Motherboard m Module Version USB Devices Enabled The USB Devices Enabled field lists the USB devices that are enabled on the system USB Function 8 USB Ports Use the USB Function BIOS option to disable USB function support or to set the number of USB ports to activate gt Disabled USB function support disabled gt 2 USB Ports Two USB ports are activated gt 4 USB Ports Four USB ports are activated gt 6 USB Ports Six USB ports are activated gt 8 USB Ports Eight USB ports are activated USB 2 0 Controller Enabled Use the USB 2 0 Controller BIOS option to enable or disable the USB 2 0 controller gt Enabled DEFAULT USB 2 0 controller enabled gt Disabled USB 2 0 controller disabled Legacy USB Support Enabled Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard support Normally if this option is not enabled any attached USB mouse or USB keyboard does not become available until a USB compatible operating system is fully booted with all USB drivers loaded When this option is enabled any attached USB mouse or USB keyboa
92. or essere nnne 58 Figure 3 20 PS 2 Pino ts reine eet ree Ie nuoto eMe eau 59 Figure 3 21 External Serial Port Connector eese 60 Figure 3 22 TV Out 61 Figure 4 1 Make sure the CPU socket retention screw is unlocked 68 Figure 4 2 Lock the CPU Socket Retention Screw esee 69 Figure 4 3 IEI CF 479B RS Cooling 69 Figure 4 4 Securing the Cooling 70 KINO 9452 Motherboard Figure 4 5 Connect the cooling fan cable eese 71 Figure 4 6 Installing the DIMM Module 72 Figure 4 7 Locking the DIMM Module enne 72 Figure 4 8 Connection of IDE Connector essere nnne 74 Figure 4 9 J mpet uerit terreur eMe eaaa a saute Rennen 75 Figure 4 10 Jumper 76 Figure 6 1 InstallShield Wizard Preparation 133 Figure 6 2 Welcome 133 Figure 6 3 License
93. orts The KINO 9452 has the following on board jumpers m Clear CMOS m COM2 mode selection RS 232 422 485 LVDS LCD voltage selection The location of these connectors on the motherboard can be seen in Figure 1 1 These connectors are fully described in Chapter 3 1 2 2 Technical Specifications KINO 9452 technical specifications are listed in Table 1 1 Detailed descriptions of each specification can be found in Chapter 2 Detailed Specifications Technology Corp KINO 9452 Motherboard M M MM 48 SPECIFICATION CPUs Supported Intel Core 2 Duo Core Duo Core Solo with 533 667MHz FSB Chipsets Northbridge Intel 945GM Southbridge ICH7 M Controller ICH7 M Graphics Support Intel Gen 3 5 Integrated Graphics Engine Display CRT HDTV MacroVision support Overscaling Component S Video and Composite output 480P 720P 10801 1080P and NTSC PAL support LVDS Dual channel 18 bit LVDS Memory Dual channel DDR2 400 533 667MHz memory modules Max 2GB PCI Bus Interface 33MHz Revision 2 3 Serial ATA SATA Two SATA II connectors with 3 0Gb s transfer rates HDD Interface One IDE channel support two Ultra ATA 100 devices USB Interfaces Eight USB 2 0 connectors supported Serial Ports Four COM ports Extension One Mini
94. outs eese 62 Table 4 1 IEI Provided 73 Table 4 2 On board Jumpers 75 KINO 9452 Motherboard Table 4 3 Clear CMOS Jumper Settings eee 77 Table 4 4 JP1 Jumper 66 77 Table 4 5 JP2 Jumper 66 1111111 eese enne nennen tnnt 78 Table 5 1 BIOS Navigation 83 KINO 9452 Motherboard List of BIOS Menus BIOS Menu 1 BIOS Menu 2 BIOS Menu 3 BIOS Menu 4 BIOS Menu 5 BIOS Menu 6 BIOS Menu 7 BIOS Menu 8 BIOS Menu 9 BIOS Menu 10 BIOS Menu 11 BIOS Menu 12 BIOS Menu 13 BIOS Menu 14 BIOS Menu 15 BIOS Menu 16 BIOS Menu 17 BIOS Menu 18 BIOS Menu 19 BIOS Menu 20 BIOS Menu 21 BIOS Menu 22 BIOS Menu 23 BIOS Menu 24 E 84 86 CPU 87 IDE Configuration 88 IDE Master IDE Slave Configuration 90 Super IO Configuration cessere enne 93 Hardware Health Configuration eese 96
95. r In 4 6 8 channel configuration the function of this port becomes Front Speaker Out m Side Speaker Out port Gray Connectors the side speakers in an 8 channel audio configuration Page 56 IEI Technology Corp KINO 9452 Motherboard M M M M Microphone Pink Connects a microphone Center Subwoofer 8 Line in Rear speaker out Line out Side speaker out e Figure 3 17 Audio Connectors 3 3 2 CRT Connector CN Label CRT COM1 CN Type 15 pin female connector CN Location See Figure 3 16 labeled number 9 Pinouts See Table 3 18 The standard 15 pin VGA connector connects to a CRT or LCD display monitor 11 Figure 3 18 VGA Connector PIN NO DESCRIPTION PIN NO DESCRIPTION 1 RED 2 GREEN 3 BLUE 4 N C 5 GND 6 GND 7 GND 8 GND 9 VCC 10 GND KINO 9452 Motherboard 11 N C 12 DDC DAT 13 HSYNC 14 VSYNC 15 DDC CLK Table 3 18 VGA Connector Pinouts 3 3 3 Ethernet Connectors CN Label LAN USB1A and LAN USB2A CN Type RJ 45 CN Location See Figure 3 16 labeled number 4 and 6 Pinouts See Table 3 19 The KINO 9452 is equipped with two built in GbE Ethernet controllers The controllers can connect to the LAN through two RJ 45 LAN connectors There are two LEDs on the connector indicating the status of
96. rd can control the system even when there is no USB driver loaded onto the system Page 106 1 Technology Corp KINO 9452 Motherboard gt Disabled Legacy USB support disabled gt Enabled DEFAULT Legacy USB support enabled gt Auto Legacy USB support disabled if no USB devices are connected USB2 0 Controller Mode HiSpeed Use the USB2 0 Controller Mode option to set the speed of the USB2 0 controller gt FullSpeed The controller is capable of operating at 12Mb s gt HiSpeed DEFAULT The controller is capable of operating at 480Mb s BIOS EHCI Handoff Enabled Use the BIOS EHCI Handoff option for systems running OSes that do not have EHCI hand off support The EHCI ownership change is managed by the EHCI driver gt Disabled Systems with OSes that do not support EHCI can use the EHCI handoff functionality gt Enabled DEFAULT Systems with OSes that do not support EHCI cannot use the EHCI handoff functionality 5 3 9 1 USB Mass Storage Device Configuration Use the USB Mass Storage Device Configuration menu BIOS Menu 14 to configure USB mass storage class devices 107 KINO 9452 Motherboard BIOS SETUP UTILITY USB Mass Storage Reset Delay 20 Secl BIOS Menu 14 USB Mass Storage Device Configuration Device The Device field lists the USB devices that are connected to the system Emulation Type
97. re listed below m 640 480 DEFAULT m 800 600 m 1024 768 m 1280 1024 36bits m 1400 1050 36bits m 1600 1200 36bits m 1280 768 m 1680 1050 36bits m 1920 1200 36bits Local Flat Panel Scaling Auto Use the Local Flat Panel Scaling option to select the method of scaling for the flat panel screen attached to the system gt Auto DEFAULT Scaling is automatic gt Forced Scaling Scaling is forced gt Disabled Scaling is disabled Connector Auto Use the TC Connector option to select the connector that is used to connect the system to the television The configuration option is listed below m Auto DEFAULT TV Standard VBIOS Default Use the TV Standard option to select the standard of the television connected to the system The configuration options are listed below m VBIOS Default DEFAULT Page 127 KINO 9452 Motherboard m NTSC m PAL 5 7 2 South Bridge Configuration The SouthBridge Configuration menu BIOS Menu 23 the southbridge chipset to be configured BIOS SETUP UTILITY fiudio Controller Azalia BIOS Menu 23 South Bridge Chipset Configuration Audio Controller Azalia The Audio Controller option enables or disables the High Definition Audio CODEC Azalia DEFAULT The Intel High Definition Audio controller automatically detected and enabled gt Disabled The onboard High Definition Audio controller is disabled Page 128 echnology Corp
98. reen shown in Figure 6 8 appears Click NEXT to continue the Page 136 Technology Corp KINO 9452 Motherboard installation Intel R Graphics Media Accelerator Driver g Welcome to the setup for the Intel R Graphics Media Accelerator Driver This program will install the Intel R Graphics Media Accelerator Driver on this computer It is strongly recommended that you exit all Windows programs before continuing Back Cancel Intel R Installation Frameworks Figure 6 8 VGA Driver Installation Welcome Screen Step 6 A license agreement shown in Figure 6 9 appears Read through the license agreement Intel R Graphics Media Accelerator Driver License Agreement Please read the following license agreement carefully Press the Page Down key to view the rest of the agreement INTEL SOFTWARE LICENSE AGREEMENT 15 Distribution amp Single User IMPORTANT READ BEFORE COPYING INSTALLING OR USING Do not use or load this software and any associated materials collectively the Software until you have carefully read the following terms and conditions By loading or using the Software you agree to the terms of this Agreement If you do not wish to so agree do not install use the Software Please Also Note If you are an Original Equipment Manufacturer Independent Hardware Vendor or Independent Software Vendor 15 this complete LICENSE AGREEMEN
99. s eese nennen nnns 41 Table 3 8 IDE Connector Pinouts nnne nnns 43 Table 3 9 LCD Backlight Connector Pinouts eese 44 Table 3 10 LVDS LCD Connector Pinouts esee 46 Table 3 11 Mini PCI Slot 47 Table 3 12 Power Connector Pinouts eese nennen 49 Table 3 13 COM 1 50 Table 3 14 Pinout eese eee 51 Table 3 15 SATA Drive Connector Pinouts eene 52 Table 3 16 SPDIF Pinolits 1 a a chase aun tek unt Cu Eae auarus 54 Table 3 17 USB3 and USB4 Pinouts eese nennen 55 Table 3 18 VGA Connector Pinouts 58 Table 3 19 LAN1 and LAN2 58 Table 3 20 RJ 45 Ethernet Connector LEDs eene 59 Table 3 21 PS 2 Connector Pinouts nennen 60 Table 3 22 External Serial Port Pinouts eene 61 Table 3 23 TV Out PIMOUts needed 62 Table 3 24 External USB Connector Pin
100. s are copied to the following path bootdrive Program Files Intel Intel R Matrix Storage Manager Step 9 The Select Program Folder window appears Click on the NEXT button to continue installing the driver Step 10 After the driver installation process is complete a confirmation screen appears Page 148 IEI Technology Corp KINO 9452 Motherboard Step 11 The confirmation screen allows user to restart the computer immediately after the installation is complete or to restart the computer later For the settings to take effect the computer must be restarted Once decided when to restart the computer click the FINISH button 149 KINO 9452 Motherboard THIS PAGE IS INTENTIONALLY LEFT BLANK 150 IEI Technology Corp KINO 9452 Motherboard BIOS Configuration Options 151 KINO 9452 Motherboard A 1 BIOS Configuration Options Below is a list of BIOS configuration options described in Chapter 5 SYSTOM OVERVICW 84 ATA IDE Configuration Compoatible eere 88 Legacy IDE Channels SATA Pri 89 IDE Master and IDE 89 LBA Large Mode
101. s the BIOS from using the LBA mode control on the specified channel gt Auto DEFAULT This option allows the BIOS to auto detect the LBA mode control on the specified channel Block Multi Sector Transfer Auto gt Disabled Selecting this option prevents the BIOS from using Multi Sector Transfer on the specified channel The data to and from the device occurs one sector at a time gt Auto DEFAULT Selecting this value to allows the BIOS to auto detect the device support for Multi Sector Transfers on the specified channel If supported Select this value to allow the BIOS to auto detect the number of sectors per block for transfer from the hard disk drive to the memory The data transfer to and from the device occurs multiple sectors at a time KINO 9452 Motherboard Mode Auto The PIO Mode option selects the IDE PIO Programmable mode program timing cycles between the IDE drive and the programmable IDE controller As the PIO mode increases the cycle time decreases gt Auto DEFAULT This setting allows the BIOS to auto detect the PIO mode Use this value if the IDE disk drive support cannot be determined gt 0 mode 0 selected with a maximum transfer rate of 3 3MBps gt 1 PIO mode 1 selected with a maximum transfer rate of 5 2MBps gt 2 PIO mode 2 selected with a maximum transfer rate of 8 3MBps gt 3 PIO mode 3 selected with a maximum transfer rate of 11 1MBps gt 4 PIO mode 4
102. s the location of the OffBoard PCI IDE adapter card Only select this slot if the adapter card is installed in PCI Slot 1 gt PCI Slot 2 PCI Slot 2 is selected as the location of the OffBoard PCI IDE adapter card Only select this slot if the adapter card is installed in PCI Slot 2 gt PCI Slot 3 PCI Slot 3 is selected as the location of the OffBoard Page 112 Technology Corp KINO 9452 Motherboard M M M M U PCI IDE adapter card Only select this slot if the adapter card is installed in PCI Slot 3 gt PCI Slot 4 PCI Slot 4 is selected as the location of the OffBoard PCI IDE adapter card Only select this slot if the adapter card is installed in PCI Slot 4 gt PCI Slot 5 PCI Slot 5 is selected as the location of the OffBoard PCI IDE adapter card Only select this slot if the adapter card is installed in PCI Slot 5 gt PCI Slot 6 PCI Slot 6 is selected as the location of the OffBoard PCI IDE adapter card Only select this slot if the adapter card is installed in PCI Slot 6 gt IRQ Available Use the IRQ address to specify what IRQs can be assigned to a particular peripheral device gt Available DEFAULT The specified IRQ is available to be used by PCI PnP devices gt Reserved The specified IRQ is reserved for use by Legacy ISA devices Available IRQ addresses are m IRQ3 m IRQ4 m 1805 m IRQ7 m 1809 m IRQ10 m IRQ 11 m IRQ 14
103. t menu BIOS Menu 21 to access the NorthBridge and SouthBridge configuration menus A WARNING Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction BIOS SETUP UTILITY gt North Bridge Configuration BIOS Menu 21 Chipset 5 7 1 North Bridge Configuration Use the North Bridge Configuration menu BIOS Menu 22 to configure the northbridge chipset Page 122 Corp BIOS SETUP UTILITY hipset North Bridge Chipset Configuration Auto Configure DRAM Timing by SPD Enabled 400 MHz Memory Hole Disabled 533 MHz 667 MHz Boots Graphic Adapter Priority PEGZPCI Internal Graphics Mode Select Enabled 8MB PEG Port Configuration PEG Port Auto PEG Force x1 Disabled Select Screen Select Item gt Video Function Configuration Change Option General Help Save and Exit Exit v02 59 C Copyright 1985 2005 American Megatrends Inc BIOS Menu 22 North Bridge Chipset Configuration gt DRAM Frequency Auto Use the DRAM Frequency option to specify the DRAM frequency or allow the system to automatically detect the DRAM frequency gt Auto DEFAULT Automatically selects the DRAM frequency gt 400 2 Sets the DRAM frequency to 400 2 gt 533MHz Sets the DRAM frequency to 533MHz gt 667 2 Sets the DRAM frequency to 667MHz gt Configure DRAM Timing by SPD Enabled Use the Configure DRAM Timing by SP
104. ted on the right side of the keyboard To confirm this the Number Lock LED light on the keyboard is lit PS 2 Mouse Support Auto Use the PS 2 Mouse Support option adjusts PS 2 mouse support capabilities gt Disabled PS 2 mouse support is disabled and prevented from using system resources gt Enabled Allows the system to use a PS 2 mouse Page 117 KINO 9452 Motherboard gt Auto DEFAULT The system auto adjusts PS 2 mouse support Boot From LAN Support Disabled The BOOT From LAN Support option enables the system to be booted from a remote system gt Disabled DEFAULT Cannot be booted from a remote system through the LAN gt Enabled Can be booted from a remote system through the LAN 5 5 2 Boot Device Priority Use the Boot Device Priority menu BIOS Menu 18 to specify the boot sequence from the available devices Possible boot devices may include m 18 FLOPPY DRIVE HDD CD DVD Page 118 IEI Technology Corp KINO 9452 Motherboard M M M M 3 BIOS SETUP UTILITY 1st Boot Device USB TS256MJFLASHA BIOS Menu 18 Boot Device Priority Settings 5 5 3 Removable Drives Use the Removable Drives menu BIOS Menu 19 to specify the boot sequence of the available FDDs When the menu is opened the FDDs connected to the system are listed as shown below m 1st Drive Only the drives connected to the system are shown For
105. ter IDE Slave IDE Master and IDE Slave configuration options for both primary and secondary IDE devices are shown in the BIOS menu below KINO 9452 Motherboard BIOS SETUP UTILITY BIOS Menu 5 IDE Master and IDE Slave Configuration Auto The Type BIOS option determines the type of device that the AMIBIOS attempts to boot from after the Power On Self Test POST has completed gt Not Installed Selecting this value prevents the BIOS from searching for an IDE disk drive on the specified channel Auto DEFAULT This selection enables the BIOS to auto detect the IDE disk drive type attached to the specified channel This setting should be used if an IDE hard disk drive is attached to the specified channel gt CD DVD The CD DVD option specifies that an IDE CD ROM drive is attached to the specified IDE channel The BIOS does not attempt to search for other types of IDE disk drives on the specified channel Page 90 echnology Corp KINO 9452 Motherboard M M M M gt This option specifies Removable Media Device These include but are not limited to gt ZIP 15 120 LBA Large Mode Auto The LBA Large Mode BIOS option disables or auto detects LBA Logical Block Addressing LBA is a method of addressing data on a disk drive In LBA mode the maximum drive capacity is 137 GB gt Disabled This selection prevent
106. therboard 6 4 Broadcom LAN Driver for GbE LAN Installation To install the Broadcom LAN driver please follow the steps below Step 1 Open Windows Control Panel Figure 6 12 New Office Document Open Office Document Set Program Access and Defaults Windows Update Program Updates Programs Documents Control Panel Settings Network and Dial up Connections Printers A Taskbar amp Start Menu Search Help Run Log Off paulsharpe Figure 6 12 Access Windows Control Panel Step 2 Double click the System icon Figure 6 13 139 KINO 9452 Motherboard Control Panel e Autodesk Plot Autodesk Control Panel Style Manager Plotter Use the settings in Control Panel to Y A ersonalize your computer B um Internet Game Select an item to view its description Controllers Extreme Options a zB Windows 2000 Support Java Keyboard Mail Network and Dial up Co amp gt Phone and Power Options Printers Modem amp Scanners and Scheduled Sounds and Users and Cameras Tasks Multimedia Passwords Figure 6 13 Double Click the System Icon Step 3 Double click the Device Manager tab Figure 6 14 System Properties Figure 6 14 Double Click the Device Manager Tab Step 4 Alist of system hardware devices appears Figure 6 15
107. to select the mode for Serial Port 2 gt Normal DEFAULT Serial Port 2 mode is normal gt DA Serial Port 2 mode is IrDA gt ASKIR Serial Port 2 mode is ASK IR Serial Port3 Address 3E8 This option allows BIOS to select the base addresses for serial port 3 gt Disabled No base address is assigned to serial port 3 gt 3E8 DEFAULT Serial port 3 I O port address is 3E8 gt 2E8 Serial port 3 I O port address is 2E8 gt 2F0 Serial port 3 I O port address is 2F0 gt 2E0 Serial port 3 I O port address is 2E0 Serial Port3 IRQ 11 The Serial Port3 IRQ selection sets the interrupt address for serial port 3 gt 10 Serial port 3 IRQ address is 10 gt 11 DEFAULT Serial port 3 IRQ address is 11 Serial Port4 Address 2E8 This option allows BIOS to select the base addresses for serial port 4 gt Disabled No base address is assigned to serial port 4 gt 3E8 Serial port 4 I O port address is 3E8 gt 2E8 DEFAULT Serial port 4 I O port address is 2E8 KINO 9452 Motherboard gt 2F0 Serial port 4 I O port address is 2F0 gt 2E0 Serial port 4 I O port address is 2 0 gt Serial Port4 IRQ 10 The Serial Port4 IRQ selection sets the interrupt address for serial port 4 gt 10 DEFAULT Serial port 4 IRQ address is 10 gt 11 Serial port 4 IRQ address is 11 5 3 4 Hardware Health Configuration The Hardware Health Configuration menu BIOS Menu 7 shows the operating temperature fan speeds and syste
108. usceptible to ESD It is therefore critical that whenever the KINO 9452 or any other electrical component is handled the following anti static precautions are strictly adhered to m Wear an anti static wrist band Wearing a simple anti static wrist band can help to prevent ESD from damaging the board m Self grounding Before handling the board touch any grounded conducting material During the time the board is handled frequently touch any conducting materials that are connected to the ground 4 2 Installation Considerations NOTE The following installation notices and installation considerations should be read and understood before the motherboard is installed All installation notices pertaining to the installation of the motherboard should be strictly adhered to Failing to adhere to these precautions may lead to severe damage of the motherboard and injury to the person installing the motherboard 4 2 1 Installation Notices Before and during the installation of the KINO 9452 please do the following m Read the user manual user manual provides a complete description of the KINO 9452 installation instructions and configuration options m Wear an electrostatic discharge cuff ESD O Electronic components are easily damaged by ESD Wearing an ESD cuff removes ESD from the body and helps prevent ESD damage m Place the motherboard on an antistatic pad Technology Corp KINO 9452 Motherboard

KINO-9452 User Manual v1.0

Contents

Download Pdf Manuals

Related Search

Related Contents