BGA HOT PLATE T-946 USER MANUAL
Contents
1. The green indicator light turn on open the machine is the WARM switch continuous mode The green indicator light turn off open the The machine is in the timer WARM switch mode Press and Y adjust the temperature You should preheat the machine to the stable temperature till you use it 1 Elementary operation 1 Check the power line 2 Turn on the power line press SET enter the parameters set interface 3 Set heating time This time is only effective in timer mode if the machine is in persist mode can press SET two times skip the settings Press A up W down turn minutes to your own number 0 99 minutes Press SET set the seconds turn seconds to your own number 0 59 seconds 4 Set the heating plate working temperature After time setting press SET again begin setting temperature the clock www tech168 cn 9 ELECTRONIC HOT PLATE T 946 USER MANUAL digital tube display S as following Press A up W down turn temperature to your own number 0 450 C 5 Set work mode start heating Timer mode Press SET several times until the green indicator light power off open the preheating switch WARM start heating The red indicator light turn on nixie tube start timing Continuous mode Press SET several times until the green indicator light turn on open the preheating switch WARM start heatin2. and reliability of use 5 Equipped with timing mode and continuous mode in order to meet different user requirements 6 Adopt imported high quality silicon controlled with non contact switch quick response control precision without the noise and low power consumption etc 7 Select high quality aluminum using a integrated techniques combined with excellent machining process produced heating plate has the coefficient of thermal conductivity high temperature quickly is heated evenly and heat deformation etc www tech168 cn 3 ELECTRONIC HOT PLATE T 946 USER MANUAL 8 Bottom heating mode especially suitable for LED industry aluminum base plate lamp bead welding repair effectively avoid the traditional welding mode of high temperature on light bead damage significantly extend the service life of bead light 9 Temperature control range can be suit for any electronic industry Such as lead and lead free PCB board preheat welding Repair sealing compound Adhesive Dispense constant temperature heating and industrial industries constant temperature heating sample roasting drying and other temperature test 10 Easy to operate after simple training can fully grasp the method of operation Main parameter Working bench size 267mmx320mm Rated voltage and frequency 220 230 60 50Hz Complete machine power 800 W 180mmx240mm Preheating chassis preheating size Preheating chassis temperatur
3. ELECTRONIC HOT PLATE T 946 USER MANUAL ELECTRONIC HOT PLATE T 946 USER MANUAL TAIAN PUHUI ELECTRIC TECHNOLOGY CO LTD www tech168 cn ELECTRONIC HOT PLATE T 946 USER MANUAL CATALOGUE Product a E Main AT PCRS Plat marn panel SSIS AME E SEEE EE OSERE 4 Back panelo 1 Elementary operation 2 SMD desoldering method ppp 3 SMD soldering Warranty commitment pp www tech168 cn 2 ELECTRONIC HOT PLATE T 946 USER MANUAL Product Features 1 Adopts MCU Main Processing Unit with advanced PID intelligent temperature control heating technology and advanced temperature measurement technology This technical innovation makes more accurate temperature control 2 Unique temperature correction function it bring improve the temperature measuring quality and measurement accuracy substantially 3 Parameter automatic memory function the transparency setting parameter preservation process simplifies operation 4 Equipped with timing mode and fault intelligent detection function simple fault easily excluded save time and efficient to ensure the stability
4. e range 0 450 C www tech168 cn ELECTRONIC HOT PLATE T 946 USER MANUAL Packing list Name Quantity T 946 hot plate 1 Power line 1 Fuse 1 User manuals compact disc 1 Cross flow fan 1 www tech168 cn ELECTRONIC HOT PLATE T 946 USER MANUAL Main Parts Plate main body Protective cover Hot plate m WWE e P Heat Shield Ker www tech168 cn ELECTRONIC HOT PLATE T 946 USER MANUAL 2 Front panel Heating time display Hot plate Temperature display Heating status indicator light 3 Side panel www tech168 cn ELECTRONIC HOT PLATE T 946 USER MANUAL 4 Back panel Cross flow fan socket Instructions This machine has two kinds of working mode timer mode and continuous mode 1 The timing mode First set the heating time it will stop heating when reach the setting time and give alarm The continuous mode The machine is in a constant heating status it will stop heating when close the heating switch 2 Two kinds of working mode setting and conversion The green indicator light is the working mode status light The green indicator light is bright www tech168 cn 8 ELECTRONIC HOT PLATE T 946 USER MANUAL when open the machine press SET key the green indicator light turns off press SET key three times the green indicator light is bright According to this mode cycle operate The mode selection method
5. erature condition put some cleanser on heating plate until residue dissolved use soft cloth to wipe gently Use soft cloth with anhydrous alcohol wipe the heating plate 5 Long time doesn t use should cramp out the power source plug www tech168 cn ELECTRONIC HOT PLATE T 946 USER MANUAL Warranty commitment The complete machine maintains for one year and lifelong service Long term factory price supply Provides the immediate network online Q A and the technical advisory work service Statement Between user operating manual and actual product different place take actual product as www tech168 cn 13
6. g The red indicator light turn on nixie tube start timing 6 Stop heating Heating finished turn off the heating switch WARM the red indicator light power off the heating plate stop heating if the machine is in timer mode until the time you set before the machine will stop heating automatically and the nixie tube stop timing a warning buzzer will sound 7 Cool down Open cooling switch COOL cross flow fan optional start working until the temperature of heating plate drop to normal temperature turn off the cooling switch COOL 8 Power off Turn off the main power switch POWER cramp out the power source plug www tech168 cn 10 ELECTRONIC HOT PLATE T 946 USER MANUAL 2 SMD desoldering method 1 According to the size of the PCB board and welding process requirement Set the machine work mode and heating plate output temperature 2 Open heating switch WARM heating plate start working display temperature rise until display temperature reach set number wait for a moment make the heating plate panel temperature more uniform 3 Put the PCB board on the heating plate until the solder paste melt take down the SMD with tweezers or vacuum pen 4 Work finished take down the PCB board from heating plate turn off the heating switch WARM and the main power switch 3 SMD soldering method 1 According to the size of the PCB board and welding process requirement set the machine work mode and heating plate
7. output temperature Suggest setting in timing heating condition according to the experience setting time duration which can effectively prevent PCB overly heating 2 Open heating switch WARM heating plate start working display temperature rise until display temperature reach set number wait for a moment make the heating plate panel temperature more uniform 3 Put the PCB board on the heating plate 4 Reach the time you set before the heating plate stop heating check solder paste is completely melted at this time if melting is not complete adjust the www tech168 cn ELECTRONIC HOT PLATE T 946 USER MANUAL timing time and continue heating Until solder paste completely melted take down the PCB board from heating plate Until solder paste cool and curdle welding work finished 5 Turn off and turn on the heating switch WARM one time use the last set parameters acquiescently go to the next piece of PCB board welding 6 All the welding finished turn off the heating switch WARM and the main power switch Caution 1 High temperature operation pay attention to safety bewares of burns 2 Keep heating plate clean clean with anhydrous alcohol regularly 3 If there are some tin slag on heating plate clean it in molten state Don t use the blade or metal edge tool doctoring in order to avoid the scratch heating plate 4 If there are some flux on heating plate turn off the main power s witch In normal temp
Download Pdf Manuals
Related Search