Deuce SDQ User's Manual - Communications Specialties, Inc.
Contents
1. Deuce soo Intelligent Video Scaler Ze CS Communications Specialties Inc WORLD HEADQUARTERS 55 Cabot Court Hauppauge NY 11788 TEL 631 273 0404 FAX 631 273 1638 WWW http Awww commspecial com EMAIL info commspecial com Communications Specialties Pte Ltd Serving the Asia Pacific Region 100 Beach Road 22 09 Shaw Tower Singapore 189702 TEL 65 6391 8790 FAX 65 6396 0138 email csiasia commspecial com Copyright 2001 P N 121532 Rev C Deuce SDQ User s Manual TABLE OF CONTENTS Introduction 2 Installation 3 Operation 4 Output Timing Specifications 5 Troubleshooting 6 Accessories 6 Rear Connector Pin outs 7 User and Certification Information 8 Statement of Warranty 8 INCLUDED WITH THIS PRODUCT YOU SHOULD HAVE 1 Deuce SDQ Intelligent Video Scaler 1 AC power line cord 1 12 foot composite video input cable 1 12 foot S Video input cable 1 User s Manual 1 Product Registration card AVAILABLE OPTIONAL ACCESSORIES e 15 pin VGA adapter cables for Deuce SDQ s VGA output e AC line cords for North America Japan or Europe e Rackmounting kits Deuce is a registered trademark of Communications Specialties Inc Deuce SDQ User s Manual Page 1 INTRODUCTION Thank you for purchasing Deuce SDQ the Intelligent Video Scaler With Deuce SDQ you now have the ability to enjoy high resolution film like images from any standard video source including broadcast or ca2. RESPONSE SYNTAX BACK FROM UNIT EXAMPLE COMMAND The following table lists the syntax for the user remote protocol commands COMMAND DESCRIPTION SYNTAX Write Command no parameters XX with data XX ZZ Read Command no parameters Where carriage return no line feed xx two letter command zz data from 1 to 3 digits in decimal The table below lists the possible responses back from the Deuce MC RESPONSE DESCRIPTION SYNTAX unit title version compile date compile time gt Hardware Failure gt gt xx zz gt JE1 1 gt Parameter out of range JE2 I gt JE3 gt Not valid with current state JE44 gt Communication error during JES I gt reception of command Timing error previous JE6 I gt command not yet serviced Where carriage return no line feed xx two letter command zz data from 1 to 3 digits in decimal To unlock the front panel send the following Ik 0 The unit will send back gt To read whether the front panel is locked send Ik The unit will reply with Alk 0 gt Deuce SDQ RS 232 Protocol Page 3 USER REMOTE COMMANDS All commands that are available to the Deuce SDQ user are listed in the User Command Remote Table shown below User Remote Command Table Two Letter Parameter Command Name Description n R Returns unit model name with firmname version number date and time in the following format Deuce SDQ Version 1 4 Aug 2
3. 3 2 pulldown adaptive frame vertical temporal and static mesh modes With a PAL input inverse 3 2 pulldown is not used SPECIAL KEY FUNCTIONS There are several functions that can be activated by pressing a combination of keys simultaneously Key Panel Lockout Press the VIDEO and S VIDEO buttons at the same time to lock out the key panel Key Panel Unlock Press the S VIDEO and COMPONENT buttons at the same time to unlock the key panel and allow normal operation System Reset Press the COMPONENT and the OUTPUT FORMAT buttons at the same time to reset the unit and return all settings to their factory defaults Page 4 Deuce SDQ User s Manual OUTPUT TIMING SPECIFICATIONS The timing specifications for the five output formats follow VESA specifications where applicable OUTPUT FORMAT INPUT TYPE H kHz 800 x 600 NTSC 37 7 PAL 31 4 1024 x 768 NTSC 48 4 PAL 40 3 1280 x 1024 NTSC 63 9 PAL 53 3 Line Double NTSC 31 5 PAL 31 3 Line Quadruple NTSC 63 0 PAL 62 5 Deuce SDQ User s Manual Page 5 TROUBLESHOOTING IF THIS IS YOUR PROBLEM Nothing works or no video output There is video on the output display but it appears out of sync THEN CHECK TO SEE Are any of the LEDs lit Is the Deuce SDQ plugged into the AC wall outlet Is video source connected to the unit and is it putting out a video signal as viewed on a video monitor Is the VCR or video source in the proper mode to output video as required
4. a vanacedyc acess cCadase E 2 3 Remote Command Table 0 0 eeesssssessssssssssssnsssssssnsssssnsnsaes 4 INTRODUCTION Thank you for purchasing Deuce SDQ This manual only includes information regarding the RS 232 Remote Control Protocol for Deuce SDQ For complete operating instructions please refer to the User s Manual that came with your unit Should you need to contact us for support our office is open Monday through Friday from 8 30 AM to 5 00 PM Eastern Time We also offer a comprehensive web site for your added conve nience Thank you for choosing Deuce SDQ As always we welcome your comments and suggestions OPERATION 9600 Baud 8 data bits no parity 1 stop bit Generic TTY No flow control DB 9 Female RS 232 female cable connector 4 1 Ground 2 Receive Data Transmit Data 3 n n 3 Transmit Data Receive Data 2 Ground 1 To Deuce 3DQ Rear Panel To Computer Com Port RS 232 Phoenix Type Connector Figure 1 Deuce SDQ RS 232 Remote Figure 2 Deuce SDQ RS 232 to Computer Cable Connection Remote Rear Panel Receptacle All commands are case insensitive Illegal commands or com mands with illegal parameters have no effect In such instances the unit will return an error message Please note that a carriage return is a carriage return only and not a carriage return with a line feed Deuce SDQ RS 232 Protocol COMMAND SYNTAX TO UNIT
5. 3 2000 17 27 08 No input signal 1 All numbers are in decimal 2 N A not applicable j n a a m 0 1 2 3 f al oo ooo oo Page 4 Deuce SDQ RS 232 Protocol Default Value Available Commands write only read and write read and write read and write read and write read only read only read only
6. Have you selected the proper input on the unit VIDEO S VIDEO or COMPONENT for the source selected as the active input Is the source of the video ON If you are using 5 BNC or RCA connectors to the output display try reversing the H and V sync connectors Make sure the display is capable of supporting the resolution you selected on the front of the unit Try a lower resolution ACCESSORIES The following accessories are available for Deuce SDQ They may be ordered from your dealer or from Communications Specialties If you need an accessory that isn t listed below or have a specific application for which you need assistance please give us a call Item Description 1240 Single rackmount kit This kit allows one Deuce SDQ to be rackmounted 1241 Double rackmount kit This kit allows two Deuce SDQ to be rackmounted 1119 006 6 ft VGA extension cable 1119 025 25 ft VGA 15 pin M F output extension cable 1119 050 50 ft VGA 15 pin M F output extension cable 1119 100 100 ft VGA 15 pin M F output extension cable 1206 6 ft HD 15 male to 5x BNC cable Custom cable lengths are available Call for information Page 6 Deuce SDQ User s Manual REAR CONNECTOR PIN OUTS VGA COMPATIBLE OUTPUT HD 15 CONNECTOR S VIDEO INPUT COMPONENT INPUT 3 FEMALE RCA CONNECTORS VIDEO INPUT FEMALE RCA CONNECTOR RS 232 REMOTE Rev RGBS__ i 2 Green Green TE 6 Ground Ground 8 Ground Ground op ne
7. MOVE COVER NO USER RISK OF ELECTRIC SHOCK SERVICABLE PARTS INSIDE REFER SERVICING TO DO NOT OPEN QUALIFIED SERVICE PERSONNEL operating and maintenance instructions in the litera ture accompanying this unit age within the unit that can cause dangerous electronic shocks This symbol warns the user of uninsulated volt This symbol alerts the user that there are important WARRANTY Communications Specialties Inc CSI warrants that for a period of three 3 years after purchase by the Buyer Deuce SDQ will be free from defects in material and workmanship under normal use and service A Return Material Authorization RMA number must be obtained from CSI before any equipment is returned by the Buyer All material must be shipped to CSI at the expense and risk of the Buyer CSI s obligation under this warranty will be limited at its option to either the repair or replacement of defective units including free materials and labor In no event shall CSI be responsible for any incidental or consequential damages or loss of profits or goodwill CSI shall not be obligated to replace or repair equipment that has been damaged by fire war acts of God or similar causes or equipment that has been serviced by unauthorized personnel altered improperly installed or abused RMA numbers and repairs can be obtained by contacting our sales department or by visiting our web site http www commspecial com Customers in the Asia Pacific Re
8. ar connector pin outs for the output configuration are selected by this switch REMOTE CONTROL Deuce SDQ provides for a hard wired RS 232 remote control connection using a 3 pin Phoenix type connector on the rear panel The baud rate is 9600 baud no parity 1 start bit 1 stop bit The pin out is as follows 1 Ground 2 Receive Data 3 Transmit Data C Please refer to the accompanying manual RS 232 Remote Control Protocol or our web site at www commspecial com for detailed specifications on the command structure for this remote control part Deuce SDQ User s Manual Page 3 OPERATION Deuce SDQ is designed to operate properly with any projector or display while requiring minimal set up and adjustments SELECTING AN INPUT There are three buttons on the front panel for directly selecting one of the three inputs The LED that is lit indicates the active selection The three input options are Video composite S Video Y C Y C C component SELECTING AN OUTPUT FORMAT Deuce SDQ provides the five output formats listed below Pressing the output format button on the front panel will cycle through the choices The LED that is lit indicates the current output format 800 x 600 1024 x 768 1280 x 1024 Line double Line quadruple MOTION COMPENSATION The automatic motion compensation feature will analyze the input source and choose the appropriate compensa tion Deuce SDQ will automatically select between inverse
9. ble TV video tape DVD and laser disc Deuce SDQ offers a unique automatic Motion Compensation feature that will adapt to the specific type of input source image When viewing NTSC sources Deuce SDQ s motion compensation feature automatically selects one of three different motion compensation techniques adaptive frame inverse 3 2 pulldown for original film material vertical temporal and static mesh When viewing PAL sources inverse 3 2 pulldown is not applicable Because each technique is set specifically for the type of input image the result is the clearest crispest picture quality possible making Deuce SDQ ideal for Home Theater and Professional A V applications Packed with other great features such as three scaled output resolutions 800x600 1024x768 and 1280x1024 and standard line doubling and quadrupling outputs Deuce SDQ is one incredibly versatile scaler Additional features include Composite S Video and Y C C component inputs and RGB or Y C C component outputs plus an RS 232 remote An internal power supply and simple intuitive user interface round out this sleek compact unit Like all products from Communications Specialties Deuce SDQ comes with our continuing commitment to provide support In order to assist us in this process please be sure to mail in your product registration card This will make it easier for us to notify you with any new product announcements or other information concerning our product line Shoul
10. d you need to contact us for support our office is open Monday through Friday from 8 30 AM to 5 00 PM Eastern Time We also offer a comprehensive web site for your added convenience www commspecial com Thank you for choosing Deuce SDQ As always we welcome your comments and suggestions Communications Specialties Inc 55 Cabot Court Hauppauge N Y 11788 USA Tel 631 273 0404 Fax 631 273 1638 Email info commspecial com Customers in the Asia Pacific Region should contact Communications Specialties Pte Ltd 100 Beach Road 22 09 Shaw Tower Singapore 189702 Tel 65 6391 8790 Fax 65 6391 0138 Email csiasia commspecial com www commspecial com Page 2 Deuce SDQ User s Manual INSTALLATION INSTALLATION STEPS 1 Connect the provided AC power cord into the connector marked Power on the rear of Deuce SDQ and plug the other end into an AC outlet This is an auto sensing universal input power supply and is compatible with worldwide standards 2 Connect a video source to either the COMPOSITE S VIDEO or COMPONENT input on the rear panel 3 Connect a computer monitor projector or display to the VGA compatible connector on the rear panel AVAILABLE OUTPUTS There are three output configurations available on the output VGA connector RGBHV RGBS and Y C C The rear panel switch next to the output connector selects one of the three output types The individual signals on the HD 15 connector are defined on page 7 Re
11. gion should contact Communications Specialties Inc Communications Specialties Pte Ltd 55 Cabot Court 100 Beach Road Hauppauge N Y 11788 USA 22 09 Shaw Tower Tel 631 273 0404 Singapore 189702 Fax 631 273 1638 Tel 65 6391 8790 Email info commspecial com Fax 65 6396 0138 Email csiasia commspecial com Please have your serial number located underneath Deuce SDQ available when contacting us Page 8 Deuce SDQ User s Manual Deuce soo Intelligent Video Scaler RS 232 REMOTE CONTROL PROTOCOL ld CS Communications Specialties Inc WORLD HEADQUARTERS 55 Cabot Court Hauppauge NY 11788 TEL 631 273 0404 FAX 631 273 1638 WWW http www commspecial com EMAIL info commspecial com Communications Specialties Pte Ltd Serving the Asia Pacific Region 100 Beach Road 22 09 Shaw Tower Singapore 189702 TEL 65 6391 8790 FAX 65 6396 0138 email csiasia commspecial com Copyright 2001 P N 121533 Rev C Deuce SDQ RS 232 Protocol Communications Specialties Inc Hauppauge NY 11788 USA TEL G31 273 0101 FAX G31 273 1638 WAM lititp Ananaicommspecial com EMAIL info conmspecial com 100 Beach Road 22 09 Sheav Tower Singapore 1589702 TEL 65 6391 3790 FAX 65 6396 0138 EMAIL csiasia conirspedial com COMMUNICATION PARAMETERS COMMAND FORMATS Page 2 CONTENTS Trtrod ction inin cease ec acd ed veadee tte cath at a dent ated sdelecs 2 COST AU Oy oases cao ha
12. o one Ef 1 Ground 2 Ground 3 Luminance 4 Chrominance Y center Yin Y outer Ground C center C in C outer Ground C center C in C outer Ground center Composite video in outer Ground 1 left Ground 2 middle Receive data 3 right Transmit data Deuce SDQ User s Manual Page 7 USER amp CERTIFICATION INFORMATION FCC STATEMENT WARNING This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause interfer ence to radio communications It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart B of Part 15 of FCC Rules which are designed to provide reasonable protection against such interference when operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference UL INFORMATION This product meets requirements for category E4 equipment utilizing the sample limits and methods described in AECO Test Report Number STR 19801 1 CE INFORMATION Standards to which conformity is declared EN 55103 1 1996 EN 55103 2 1997 WARNING TO REDUCE THE RISK OF FIRE OR ELECTRONIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE CAUTION CAUTION TO REDUCE THE RISK OF ELECTRONIC SHOCK DO NOT RE
Download Pdf Manuals
Related Search