Korenix JetNet 3810G Series User's Manual
Contents
1. The DIN rail should behind the spring when install the JetNet 3810G series onto the standard DIN Rail DIN Raili Follow the steps below to mount the JetNet 3810G series on the DIN Rail track 1 Insert the upper end of the DIN Rail clip into the back of the DIN Rail track from its upper side 2 Lightly push the bottom of the DIN Rail clip into the track 1 378 Inch 3 5cem gt Kor 4 0 295 Inch JetNet 3810 Gf 0 75cm M m 063 Inch 2 7cm DIN EN 50022 DIN Rail Dimension 3 Check if the DIN Rail clip is tightly attached to the track To remove the JetNet 3810G series from the track reverse the steps above 3 Appendix 3 1 Product Specification 3 2 Revision History 3 1 Product Specification Technologies Standard Performance Switch Technology System Throughput Transfer packet size MAC Address Packet Buffer MTBF Interface Configuration IEEE 802 3 10Base T Ethernet IEEE 802 3u 100Base T Fast Ethernet IEEE 802 3ab 1000Base T JetNet 3810G 3806G 3710G IEEE 802 3z Gigabit Ethernet Fiber only JetNet 3810Gf IEEE802 3x Flow Control and Back pressure except JetNet 3810f for 100M fiber IEEE 802 3af Power Over Ethernet IEEE 802 1p Class of Service Store and Forward Technology with 32Gbps Switch Fabric 14 880pps for 10M Ethernet 148 800pps for 100M Fast Ethernet 1 488 100pps for Gigabit Ethernet 64 bytes to 1522 bytes for unt2. Gf 3806G 3710G JetNet 3810Gf 3810f includes system power LED x1 alarm relay LED x1 PoE LED x8 16 LEDs for RJ 45 port operating status and 4 LEDs for SFP fiber port status Power LED Korenix Alarm Relay LED PoE Indicators LED for RJ 45 port LED for fiber speed LED for fiber LNK ACT JetNet 3810Gf Korenix JetNet 3810 Gf 3806G 3710G Bottom View Relay Output i i Earth Ground Screw DIP Switch O Terminal Block BHBBEBBHBBBH The bottom side of the JetNet 3810 Gf 3710G includes one 4 pin removable terminal block connector with 1 power input amp 1 relay alarm output and one 10 Pin DIP Switch for ports link failure alarm 6 Pin DIP Switch for JetNet 3806G There is also an earth ground screw to prevent interference LED Indicators The following table describes the function of each LED indicator LED Status Description Green DC IN Power Jack is On PWR Off No Power in DC IN Red Ports link failure occur Alarm Off No failure is found PoE LED Status Description Green The port is delivering PoE power PoE 1 8 Off No PD is attached 10 100 TX Port LED LNK ACT Green on RJ 45 port is attached with partner Korenix 10 JetNet 3810 Gf 3806G 3710G FDX COL Blinking Blinking For JetNet 3810G 3806G 3710G GbE TX Port LED LNK ACT Speed For JetNet 3810
3. Gf 3810f GbE FX Port LED LNK ACT Speed Green on Blinking Off Yellow Blinking off Green on Blinking Off Yellow Blinking off RJ 45 port is transmitting or receiving packets RJ 45port s link is inactive Link with partner on Full Duplex mode Data collision is occurred RJ 45 port s link is inactive or link as Half Duplex mode Description RJ 45 port is attached with partner RJ 45 port is transmitting or receiving packets RJ 45port s link is inactive 3 blinks per order 1000Mbps 2 blinks per order 100Mbps 1 blinks per order 10Mbps RJ 45 port s link is inactive Description Fiber port is attached with partner Fiber port is transmitting or receiving packets Fiber port s link is inactive 3 blinks per order 1000Mbps 2 blinks per order 100Mbps Fiber port s link is inactive NOT supported in JetNet 3810f 100M fiber is optional and can be supported by different settings Korenix JetNet 3810 Gf 3806G 3710G 11 2 2 Wiring the Power Inputs JetNet 3810 Gf 3806G accepts 12 24V DC power input and boosts to 48V DC output for 802 3af standard PoE devices JetNet 3710G without power boosting function accepts only 48V DC power Input IMPORTANT Do make sure that different models must connect to the corresponding supply voltage Guarantee will not apply to the damage caused by wrong input power N
4. Input input 48V 48V PoE 48V PoE 48V PoE 48V PoE PoE output output output output output Specifications may change without prior notice Korenix 5 JetNet 3810 Gf 3806G 3710G 2 Hardware Installation 2 1 Hardware Introduction Dimensions JetNet 3810 Gf dimensions 149 0 H x 131 2 W x 66 0 D with Din rail clip Korenlx PWR 1203040 an 14 ES 131 20 120 60 AE T 7 P 1 Ou JetNet 3810G 49 6 JetNet 3810 Gf 3806G 3710G JetNet 3806G dimensions 149 0 H x 131 2 W x 66 0 D with Din rail clip 131 20 Korenlx PWR Alam T GP ar JetNet 3710G dimensions 149 0 H x 131 2 W x 66 0 D with Din rail clip 131 20 Korenlx PWR Alam 172 9 4 PoE ar 675 Korenix 7 JetNet 3810 Gf 3806G 3710G Front Panel JetNet 3810G 3710G includes system power LED x1 alarm relay LED x1 PoE LED x8 and 20 LEDs for the port operating status JetNet 3806G includes system power LED x1 alarm relay LED x1 PoE LED x4 and 12 LEDs for the port operating status JetNet 3810G 3710G JetNet 3806G Power LED Korenix Korenix Alarm Relay LED PYRO Alarm PoE Indicators PoE LED for RJ 45 port 2 4 RJ 45 ports for 10 100Mbps RJ 45 ports for GbE 10 100 1000M 1 P JetNet 3810G N N JetNet 3806G Korenix 8 JetNet 3810
5. Korenix JetNet 3810G Series JetNet 3810 Gf 3806G 3710G Industrial Power over Ethernet GbE Switch User s Manual Sixth Edition March 2012 korenix www korenix com Korenix JetNet 3810G Series JetNet 3810 Gf 3806G 3710G Industrial Power over Ethernet GbE Switch User s Manual Copyright Notice Copyright 2008 Korenix Technology Co Ltd All rights reserved Reproduction in any form or by any means without permission is prohibited Korenix JetNet 3810 Gf 3806G 3710G NRO PE 2 T TritFrod dud nas 3 TT OVervie Wiss tede det 4 1 2 Product Features Roa a deer P des coe nt piae oti det 5 2 Hardware InstallatlOFic e dass deo verte adie PD abf 6 2 1 Hardware a be vu one apuro bes dau 6 Dimensions ueste dee e pee ERE 6 Front Pan l oos cie iet anto eso dietis Du debba Tur Abad 8 Bottom 10 LED de eni 10 2 2 Wiring the Power Inputs 12 2 3 Wiring the Relay aa e aa aiaa 13 2 4 Wiring Earth Ground sssessssssssseeeeeee eee enne enhn nnne nennen nnne nr sre 14 2S DIP SWITCHES m 14 2 6 Wiring the Ethernet Ports ccccccccccccssssssececeesesssessaeeesecesssess
6. ag and tagged frames 8k 1 Mbits Greater than 20 000 hours 25 802 3af compliant PoE ports x 8 JetNet 3810 Gf 3710G x 4 JetNet 3806G 10 100 1000Base TX x 2 JetNet 3810G 3806G 3710G Gigabit 100 Base FX SFPx 2 JetNet 3810Gf 100 Base FX SFP x 2 JetNet 3810f Auto MDI MDI X Auto Negotiation Korenix 19 JetNet 3810 Gf 3806G 3710G Cables Diagnostic LED Relay Alarm POE technology Power Requirements Power Power Consumption Mechanical Construction Mounting Dimension Net weight 10Base T 2 pair UTP STP Cat 3 4 5 cable 100m 100 Base TX 2 4 pair UTP STP Cat 5 cable 100m 1000 Base T 4 pair UTP STP Cat 5 cable 100m Power Green x1 Fault alarm Red x1 PoE Green x8 JetNet 3810 Gf 3710G x4 JetNet 3806G Link Activity Green x8 JetNet 3810 Gf 3710G X4 JetNet 38066 Full duplex Collision Yellow x8 JetNet 3810 Gf 3710G x4 JetNet 3806G JetNet 3810G 3806G 3710G Gigabit Copper Link Activity Green x2 Gigabit Copper Speed Yellow x2 JetNet 3810Gf Gigabit fiber Link Activity Green x2 Gigabit fiber Speed Yellow x2 JetNet 3810f Fiber Link Activity Green x2 Fiber Speed Yellow x2 Dry Relay output with 1A 24V ability Alternative B 12 24V DC input voltage JetNet 3810 Gf 38066 48V DC input voltage JetNet 3710G Isolated 3 3V system power JetNet 3810 Gf 3710G 30 Watt without PoE loading 95 Watt with full PoE loading JetNet 3806G 25 Watt
7. ight through or crossover cabling For JetNet 3810G 3806G 3710G model the switch also provides two 10 100 1000 Base TX uplinks Port 1 to port 8 4 also provides Power over Ethernet function that delivers DC 48V power through the spare pairs to power the PD Korenix 15 JetNet 3810 Gf 3806G 3710G The following figures depict the schematic diagram of straight through and crossover cabling Note that crossover cables simply cross connect the transmit lines at each end to the receive lines at the opposite end Switch Router or PC Switch Switch 3 TD 3 RD 3 TD TD 6 TD 6 RD 6 TD TD 1 RD RD RD4 4 TD4 2 RD 2 RD 2 RD 4 2 TD Straight through Cabling Schematic Cross over Cabling Schematic Note that Ethernet cables use pins 1 2 3 and 6 of an 8 pin RJ45 connector The signals of these pins are converted by the automatic MDI X function as shown in the table below Pin MDI X Signals MDI Signals 1 RD TD 2 RD TD 3 TD RD 6 TD RD Connect one side of an Ethernet cable into any switch port and connect the other side to your attached device The green LNK LED will light up when the cable is correctly connected Refer to the LED Indicators section for descriptions of each LED indicator Always make sure that the cables between the switches and attached devices e g switch hub or workstation are less than 100 meters 328 feet 2 7 W
8. iring the Fiber Ports only JetNet 3810Gf JetNet 3810Gf equips 2 gigabit SFP fiber ports The speed of the SFP port supports up to 1000Base SX LX The SFP ports accept standard MINI GBIC SFP transceiver But to ensure system reliability Korenix recommends using the Korenix certificated Gigabit SFP Transceiver The certificated SFP transceiver includes 1000Base SX LX single multi mode ranger from 550m to 80KM The way to connect the SFP transceiver is to plug in SFP fiber transceiver fist Cross connect the transmit channel at each end to the receive channel at the opposite end as illustrated in the figure below 16 Note This is a Class 1 Laser LED product Don t stare at the Laser LED Beam Note 100Base FX SFP transceiver is optional and can be supported by different settings Note The unit has to use UL recognized Laser Class 1 SFP transceiver 2 8 Connecting Powered Device PD Port 1 to port 8 4 provide PoE inject function with maximum 15 4w ability to power up the powered device use the straight or cross over Ethernet cable The JetNet 3810 Gf 3806G 37106 follow the IEEE802 3af Alternative B mode connector assignment The following table shows pin assignment of alternative A and B for the PSE Power Source Equipment psc CON Alternative A Alternative A Alternative B MDI X MDI 1 amp Negative Vport amp Positive Vport 2 amp Negative Vport amp Posi
9. ote The product intended to be supplied by LPS power supply 1 Insert the positive and negative wires of your DC supply into the V and V contacts of the terminal block connector The acceptable wire range is 12 to 24 AWG JetNet 3810 Gf 3806G AC DC Power Supply DC 12 24 V min 4 A UL Listed DC Power output v DC 12 24 V EI vt 12 24AWG Wire AC Power input Relay PWR Korenix 12 JetNet 3810 Gf 3806G 3710G 37100 AC DC Power Supply DC 48 V min 2 A UL Listed DC Power output AC Power input 2 Tighten the terminal screws to prevent the DC wires from coming loose 2 3 Wiring the Relay Output JetNet 3810 Gf 3806G 3710G provide Relay Output The relay contacts are energized open for normal operation and will close under faulty condition such as Ethernet port link break The Relay alarm can be configured by DIP Switches Korenix JetNet 3810 Gf 3806G 3710G 13 Alarm System Earth Ground Maximum 14A current DC 24V Extra Power System IIE o Port Llak Fall Alarm B A 1 10 Relay PWR BBHiBBBBHB 0 2 4 Wiring Earth Ground To ensure the system will not be damaged by noise or electric shock we suggest making a direct connection between the JetNet 3810 Gf 3806G 3710G and earth ground to avoid system damage Please refer to the upside photo 1 On the bottom of the JetNet 3810 Gf 3806G 37106
10. saeeeeeeeesseeseeaes 15 2 7 Wiring the Fiber Ports only JetNet 3810Gf 16 2 8 Connecting Powered Device PD c cccccessscecesssceceessssececsesseeecessseeeeessaaes 17 2 9 DIN Rail Mounting 18 3 19 3 1 Product Specifications ite 19 3 2 REVISION HISLORY EE 21 Korenix 2 JetNet 3810 Gf 3806G 3710G 1 Introduction Korenix JetNet 3810G Series is a power over Ethernet rail switch that is specially designed for industrial or commercial applications The following topics are covered in this chapter 1 1 Overview 1 2 Product Features Korenix JetNet 3810 Gf 3806G 3710G 1 1 Overview JetNet 3810G series Industrial Power over Ethernet PoE GbE Switches are designed with 8 4 Fast Ethernet PoE ports and 2Gigabit uplink ports to ensure high bandwidth uplink connection for wide PoE markets This series include JetNet 3810G 3806G 3710G which are all compliant with IEEE 802 3af PoE standard to deliver maximum 15 4Watts per port For JetNet 3810G 3806G model it integrates with Korenix patented power boost technology Input DC 12 24V boosting to 48V built in power booster which is the best solution for the vehicle PoE applications with standard DC 48V power supply unavailable For fiber Switch series
11. such as JetNet 3810Gf it combines hot swappable SFP fiber transceiver interfaces which can meet different specifications of fiber cable for extending transmission distance To ensure the high quality of video data transmission JetNet 3810G series not only provide Gigabit bandwidth uplink for large image traffic but also support QoS to adjust the priority of data transfer With the feature of Fault Relay JetNet 3810G series could automatically warn administrator if any abnormal situation happens The compact size with IP 30 rigid aluminum case allows JetNet 3810G series to be reliably operated 25 60 C extreme environment Korenix 4 JetNet 3810 Gf 3806G 3710G 1 2 Product Features Korenix JetNet 3810 Gf 3806G 3710G have the following features 10 100 TX PoE port JetNet 3810G 8 8 JetNet 3710G JetNet 3806G JetNet 3810f JetNet 3810Gf 8 8 4 10 100 1000 TX uplink port Giga FX SFP 2 100 FX SFP 2 PoE Standard compliant Yes Yes Yes Yes Yes IEEE802 3af PoE PoE Power per port 15 4W 15 4W 15 4W 15 4W 15 4 Total PoE Power Budget 65W 65W 65W 60W 65W Quality of Service Yes Yes Yes Yes Yes Fault relay alarm Yes Yes Yes Yes Yes Aluminum Case Protection Operating Temperature 25 60 C 25 60 C 25 60C 25 60 C 25770 C 12 24V 12 24V 12724V 12724V 48V power power input power input power input powerinput Power
12. there is one earth ground screw 2 Loosen the earth ground screw with a screwdriver 3 Tighten the screw after the earth ground wire is connected 2 5 DIP Switches 10 Pin Dip switches are located on the bottom panel of JetNet 3810 Gf 3710G for configuration purpose 6 Pin for JetNet 3806G They are used to configure Port Alarm to corresponding TX ports Korenix 14 JetNet 3810 Gf 3806G 3710G DIP Switch number Status Description To enable GbE port break alarm at this port DIP 172 JetNet 3810 Gf 3710G To disable GbE port break alarm at this port 3806G Off Default To enable PoE port break alarm at this port To disable PoE port break alarm at this port JetNet 3806G Off DIP 376 Default DIP Switch number mapping to corresponding PoE port amp GbE port as follow DIP Switch 3 4 5 6 7 8 9 10 PoE port 1 2 3 4 5 6 7 8 For JetNet 3810G 3710G 3806G DIP Switch 1 2 GbE port 2 1 For JetNet 3810Gf 3810f Dipswitch 1 2 GbE port 1 2 2 6 Wiring the Ethernet Ports JetNet 3810 Gf 38066 37106 Industrial Gigabit PoE Switch support 8 4 RJ 45 ports with automatic MDI MDI X crossover PoE Injector and automatic 10 100Mbps data rate sensing for 10Base T or 100Base TX connections Automatic MDI MDI X crossover allows you to connect to other switches hubs or workstations without regard to using stra
13. tive Vport 3 Tx amp Positive Vport Rx amp Negative Vport 4 Positive Vport 5 Positive Vport 6 Tx amp Positive Vport Rx amp Negative Vport 7 Negative Vport 8 Negative Vport PIN Assignment of PSE Be sure the twisted pair cable is bound with the standard RJ 45 pin especially the pin 4 5 7 and 8 If the RJ 45 is bound with the wrong pin number JetNet will not 1 8 recognize the PD and won t forward DC 48V power to PD since the JetNet 3810G series switch following the Alternative B mode In the IEEE 802 3af standard documents it indicates the PD should support mode A and B and only receiver power from either mode A or mode B The following table shows the RJ 45 pin out for the PD Korenix 17 JetNet 3810 Gf 3806G 3710G PD Pinout Conductor Mode Mode B 1 Positive Vport Negative Vport 2 Positive Vport Negative Vport 3 Negative Vport Positive Vport 4 Positive Vport 5 Positive Vport 6 Negative Vport Positive Vport 7 Negative Vport 8 Negative Vport Note This product is designed for in building installation only and is not intended to be connected to exposed outside plant networks 2 9 DIN Rail Mounting Installation The DIN Rail clip is already attached on the rear side of JetNet 3810 Gf 3806G 3710G It supports EN 50022 standard DIN Rail in the following diagram includes the dimension of EN 55022 DIN Rail for your reference
14. without PoE loading 80 Watt with full PoE loading Rugged Aluminum Alloy Chassis IP30 protection DIN Rail mount 66 W x 149 H x 131 2 D mm with Din rail clip 1 05kg Korenix 20 JetNet 3810 Gf 3806G 3710G Environment Operating Temp JetNet 3810 Gf 3806G 13 140 F 25 60 C 5 to 9596 RH JetNet 3710G 13 158 F 25 70 C 5 to 9596 RH Storage Temp 40 176 F 40 80 C 5 to 9596 RH Railway EN50155 EMC EMI FCC class A CE EN55022 Class A EMC EN61000 4 2 EN61000 4 3 EN61000 4 4 EN61000 4 5 EN61000 4 6 EN61000 4 8 EN61000 4 11 Shock IEC60068 2 27 50g peak acceleration Vibration IEC60068 2 6 5g 5 500Hz random operation Warranty 5 years Specifications may change without prior notice pending 3 2 Revision History Edition Date Modifications V0 1 06 30 2010 New edition V0 2 10 22 2010 Add JetNet 3810Gf V0 3 02 11 2011 Add port alarm note 1 Add JetNet 3810f VO 6 03 05 2012 E 2 Modifying DIP switches Korenix 21 JetNet 3810 Gf 3806G 3710G
Download Pdf Manuals
Related Search