Operating Instructions Patronic with Selectron-MAS-Control
Contents
1. loom e Attention is given to the hooks moved by magnet while in action the lifting hook has to hang completely on the lifting Knife e When the shed is closed the right pedal when pushed down should not touch the floor under any circumstances e Check again that the steel ropes from the pedals to the machine drive lie correctly in the groove of the rollers 11 4 Information Addresses from the program of weave which are communicating with the Selectron MAS Control Verson ARM e Weave Point www weavepoint com e DB Weben www brunoldsoftware ch e Pointcarr www pointcarre com e WeaveMaster www kienbaum webereitechnik de e Weave for Windows www digitalweaving no e ScotWeave www scotweave com e Pro Weave www proweave com 10 1 Description of PATRONIC i ii Selectron box Box of Selec tron display handlerer lathe with shuttle box foot frame metalbar pedal axe with pedals bar with the rope rollers screws with nuts diversion roller with steel ropes Tuts To Ei hoe ARM ARM 2 Starting the loom PATRONIC e Close switch off the loom the pattern is saved 2 1 By delivery with assembled foot frame Unpack the loom carefully cut the packaging ribbons take off the e Shafts forward or backwards top box cut the fixing ribbons on the pallet Mode Enter Lift up the loom and place it in its proper palce If the loom can not forward be moved to its2. Operating Instructions Patronic with Selectron MAS Control 02 2009 ARM AG Weberei Artikel Fabrik CH 3507 Biglen Switzerland Tel 41 0 31 701 07 11 Fax 41 0 31 071 07 14 www arm loom ch info arm loom ch ARM Contents Page 1 Description of PATRONIC 3 2 Starting the loom PATRONIC 4 e 2 1 By delivery with assembled foot frame 4 e 2 2 By delivery with dismantled foot frame 5 3 Description of the Selectron MAS Control 6 e 3 1 Weave with software and computer T e 3 2 Weave with box of the Selectron display 8 9 4 Information 10 5 Functions of dobby 11 If you have questions concering the Patronic and the Selectron Control which are not answered by this manual please contact ARM AG ARM Functions of dobby e Inthe closed shed the programmed magnets are pulled during 5 seconds operating the hooks e The hooks which are pushed down hang on the lifting knife and pull the shafts up accordingly e The hooks which are not pushed hang on the lowering knife and pull the shafts down Bo0 PATRONIC Control of the stops in the closed shed H T e mi pu 1 tly By pressing the rotor rod in the closed shed the hooks ore fasten between the two knifen the steps must move without any resistance in the pressed position Bj and fall back in neutral position when oe ee Notice e Incase the dobby blocks while trying the motions have to be watched precisely e Take off the wooden top cover of the
3. e The Selectron MAS Control and the Selectron display with the box is a new generation e The Control 40x20x7 cm for 24 shafts is installed in the loom 5 Selectron e Innovation of the Selectron MAS Control Capacity of 999 weft Selectron display with box 20x11x5 cm in german french and english Selectron Oe i l F5 l Ese Enter e Explication of the keys Key F1 F5 Esc Enter 4 arrow direction 2 red keys LED L1 L4 Indication 4 lines line 1 Titel line 2 Up date position of the loom line 3 F1 Enter F2 Language line 4 Start Rapport e Two applications are possible with the Selectron MAS Control Enter with software and computer Enter with box of the Selectron display 3 1 Weave with software and computer e Data cable 9pin connect on the computer e Switch on the power switch green e Delete the data F1 F2 Enter for weave direct indirect e Left pedal down e Switch on the computer e Load the pattern design e With the corresponding configuration the following systems are possible un Weave direct the pattern is transmitted weft by weft from the computer press the right pedal MER I wait about 2 seconds for the noise of the magnets then the left pedal for the next weft close Esc the pattern is deleted close the programm in the computer 1 Weave indirect the pattern is loaded on the Selectron MAS Control Weave 0000 S Sel
4. e hexagonal wrench Tighten the nuts of the metalbar see 1 Mount the bar with the rope rollers see 3 and tighten the nuts Place the foot frame in its proper place Unscrew the 4 nuts of the side bars and take the screws off see 4 place the loom on the foot frame and assemble the sides with the side bars of the foot frame Be careful not tighten too hard the nuts Installing the steel ropes Loosen the steel ropes until they hang down from the top rollers on both sides Place the steel ropes on the diversion rollers as shown in the diagram on page 3 Take care that the steel ropes are placed correctly between the diversion rollers and the ropes lead Hook the pedals on the steel ropes and tighten the 4 nuts see 6 Mount the shuttle boxes on the lathe Mount the second back bar Hang up the Selectron box according to indication page 4
5. ectron s F3 0000 press the right pedal then left pedal for the next weft the weft position is indicate on the right side of the display F4 weft individual forward weave backwards F5 L4 light on with F4 weft individual backwards close F1 F2 Enter the pattern is deleted HE wa Esc Enter 3 2 Weave with box of the Selectron display e Switch on the power switch green e Erase the data F1 F2 Enter only for new enter e Left pedal down EN me S F4 F5 Esc ES e Choose the language F2 Enter a pattern desgin 2xF1 L1 light on with keys am Take the Selectron box with the display in the hand lifting shaft 1 lowerina shaft 0 or red keys Close Enter F5 L1 L4 light on Back to weft 0 F4 then F5 Weave 2xEsc Rapport Start F3 Weave 0000 F3 0000 Press the right pedal then Left pedal for the next weft The weft position is indicate on the display For exemple tabby 1 lifting 1 lowering and so on 2 2 By delivery with dismantled foot frame Unpack the loom carefully cut the packaging ribbons and strings take off the top box and unwrap the parts The loom remains on the pallet Assembling the foot frame Fit the right part of the foot frame onto the metalbar see 1 repeat the same with the left part on the foot tighten the nuts only by hand Attach the pedals to the pedal axe see 2 and tighten the special screws with th
6. proper place it is possible to lift it up from the foot frame as follows _ backwards unscrew the 4 nuts of the side bars and take the screw off see 4 the steel ropes can be unhooked above the pedals the steel ropes can be lifted out of the diversion rollers above e Wefts forward or backwards see 5 To do this unscrew the nuts see 6 of the diversion Mode Enter F5 forward Enter rollers a little bit until the steel ropes can be taken off backward F4 Lift the loom off the foot frame and place it in its proper place Assembling the foot frame and installing in the steel ropes according to page 3 5 g to pag It is possible to enter serveral patterns For example Pattern 1 Weft 0 1 Tabby Take off packaging strings and foils Pattern 2 Weft 10 11 mat weave Mount the shuttle boxes on the lathe Mount the second back bar e Enter for pattern 2 2 lifting 2 lowering and so on Hang up the Selectron box on the left side of the loom en u r on connect the machine cable with the loom 15 pin eee IN Ne e Weave 2xEsc Connect the main cable into the mains 230 Volt e Rapport Start F3 Weave 0010 and switch on the power F3 0010 normal power input control only 9 Watt e Press right pedal then Maximum power input 144 Watt e Left pedal for the next weft max shaft lifting 20 shafts e The weft position is indicate on the display 3 Description of the Selectron MAS Control with serial port
Download Pdf Manuals
Related Search