User manual UM EN THERMOMARK CARD
Contents
1. Ribbon supply hub Ribbon take up hub Transport lock Print mechanics Transport slide 2 2 Installation Unpacking and Setting up the Printer gt Lift the printer out of the box and set it up on a level surface P Check printer for damage which may have occurred during transport P Check delivery for completeness Contents of Delivery Printer Power Cable Type E F USB Cable Operator s Manual DVD with application software driver and documentation THERMOMARK RIBBON 110 50 TC Magazine THERMOMARK CARD UCT MAG 1 and THERMOMARK CARD US MAG 1 Printed Samples UCT and US Label cards UCT and US Package of felt sticks Notice Please keep the original packaging in case the printer must be returned Attention The device and printing materials will be damaged by moisture and wetness gt Setup printers only dry locations protected from splash water 2 Installation 2 3 Connecting the Device i 2 1 Power switch USB master ports for keyboard WS Zi scanner or memory stick 5 E GE Gr USB high speed slave port Ethernet 10 100 Base T Power connection jack oR Fig 2 Connections 2 3 1 Connecting to the Power Supply The printer is equipped with a wide area power unit for a supply voltage of 100 V to 242. CLIP PROJECT Afterwards configure the THERMOMARK CARD in the planning and marking software CLIP PROJECT in the module Marking gt Add the THERMOMARK CARD as new printer in CLIP PROJECT Marking under File configure output device Therefore select THERMOMARK CARD from the selection box and click New Then select OK 2 Installation 2 3 3 Connecting to a Network via Ethernet The integrated Ethernet interface allows the operation of the printer in a network To connect the printer to a network outlet a patch cable with a RJ45 plug for 10Base or 100Base T is necessary Attention When connecting the printer to the network a shielded cable must necessarily be used gt Connect computer to a printer by a suitable cable 2 4 Switching on the Device Attention gt Unlock transport lock before switching on the printer gt 7 1 on page 28 When all connections have been made Switch the printer on at the power switch 1 The printer performs a system test and then shows the system status READY in the touch screen display If an error occurs during the system test the symbol A Critical i fault and type of error are Fig 3 Power Switch displayed 113 Touchscreen Display 3 1 Structure of the Touchscreen Display 10 40 x Ro THERMOMARK CARD 57 READY
3. Fig 4 Touchscreen Display The touchscreen display 1 indicates the current status of the printer and the print job indicates faults and shows the printer settings in the menu By selecting the buttons on the touchscreen display 1 settings can be made 3 2 Operating the Touchscreen Display The touchscreen display is operated directly by touch Toopen a menu or select a menu item lightly touch the corresponding symbol To scroll in lists slide finger up or down on the display 3 Touchscreen Display 3 3 Symbols on the Start Display Symbol Status Function Ready To offline menu Error oO Ready After the end of a print job reprint the last card Ready Delete internal memory the last card can longer be reprinted Print Cancel current print job and delete all print Error jobs Ready with If print data are available the print is triggered extended slide If there are no print data available the slide is retracted 9 Ready with retracted slide Set slide into insert position Table 1 Symbols on the Start Display EK Touchscreen Display 3 4 Printer States and 9 State Display Description Ready Ready andthe symbols The printer is the ready state e and can receive data The slide is and retracted Ready Ready the symbols The printer is in the ready state and can receive data The slide is extended
4. Ready after first print Ready and the symbols and O The printer is in the ready state and can receive data Insert Material Insert and the symbols D B 9 In order to process a print job new material must be inserted After inserting the material and confirming with e the print job is processed Critical fault and the type of error Display flashes red Print Card description and the The printer is currently processing number of the printed active print job card in the print job th Data can be transmitted for a new print job symbols DI and y The new print job will start when the previous one has finished Error A An error has occurred and the type of error the card description and the number of cards still to be printed and the symbols B e Critical fault An error occurs during the system test gt Switch the printer off and then on again at the power switch or Call Service if the fault occurs persistently 3 Touchscreen Display Power Save If the printer is not used for a lengthy Mode period it automatically switches to 9 power save mode P To exit power save mode Touch touchscreen display Table 2 Printer States 3 5 Touchscreen Display Configure Ethernet Interface The Ethernet interface can be configured under menu item Setup gt Interfaces The following parameters are necessary for o
5. User manual UM EN THERMOMARK CARD Thermal transfer printer for cards o dDO0 dD ED CD Jc DE INSPIRING INNOVATIONS User manual Thermal transfer printer for cards 2012 01 30 Designation UM EN THERMOMARK CARD Version 02 Order No This user manual is valid for Designation Order no THERMOMARK CARD 5146464 THERMOMARK CARD AR 5146736 104612_en_02 PHOENIX CONTACT i General terms and conditions of use for technical documentation Phoenix Contact reserves the right to alter correct and or improve the technical documentation and the products described in the technical docu mentation atits own discretion and without giving prior notice insofar as this is reasonable for the user The same applies to any technical changes that serve the purpose of technical progress The receipt of technical documentation in particular user documentation does not constitute any further duty on the part of Phoenix Contact to fur nish information on modifications to products and or technical documenta tion You are responsible to verify the suitability and intended use of the products in your specific application in particular with regard to observing the applicable standards and regulations All information made available in the technical data is supplied without any accompanying guarantee whether expressly mentioned implied or tacitly assumed In general the provisions of the current standard Terms and Condit
6. slide Insert material into the magazine on the extended transport slide Note The cards must be dry free from grease fingerprints and dust Insert UCT material Insert material in a way that the smaller rectangle is positioned at the rear left and the feet Fig 12 3 point into the direction of the magazine The material must click into the guides Fig 11 2 of the magazine At the front right two similar rectangles 1 as shown in Fig 8 must be visible oo UCT MAG3 Fig 8 Rectangles on the UCT material Note UCT material can also be printed if one or more complete strips of the card are missing 215 Printing Operation Incorrect Fig 9 UCT material inserted Fig 10 UCT material inserted correctly incorrectly turned by 180 degrees Fig 11 UCT material feet down Fig 12 material feet up Fig 13 UCT material with two or Fig 14 material with more complete strips incomplete strips 5 Printing Operation Insert US material Correct Incorrect Fig 15 US material inserted Fig 16 US material inserted correctly incorrectly 1 2 Put holes of the material precisely onto the pins of the magazine Select 57 Material is checked by the printer If the material is inserted incorrectly or does not correspond to the material shown on the display th
7. material print command The boreholes of the UCT Clean the boreholes in the UCT magazine are dirty magazine Table 4 Error Messages and Fault Correction 9 Licences 9 1 EC Declaration of Conformity PHCENIX CONTACT 5146464 CE 01 EG Konformit tserkl rung EC Declaration of Conformity PHOENIX CONTACT GMBH amp CO KG Hersteller Manufacturer Flachsmarktstra e 8 D 32825 Blomberg Germany Anschrift Address Produktbezeichnung Product description THERMOMARK CARD Artikelbezeichnung Article description 5146464 Artikel Nr Article no Das vorstehend bezeichnete Produkt stimmt mit den wesentlichen Anforderungen der nachfolgenden Richtlinie n und deren Anderungsrichtlinien berein The above mentioned product is in line with the essential requirements of the below directive s and their modification directive s EMV Richtlinie Elektromagnetische Vertraglichkeit 2004 1 08 EC Electromagnetic Compatibility Directive EMC Niederspannungs Richtlinie NSR 2006 95 EC Low Voltage Directive LVD F r die Beurteilung der bereinstimmung wurden folgende einschl gige Normen herangezogen For evaluation of the conformity following relevant standards were consulted EN 60950 1 2006 A1 1 2009 EN 61558 1 2005 A1 EN 55022 2006 A1 EN 55024 1998 A1 A2 EN 61000 3 2 2006 A1 A2 EN 61000 3 3 2008 EN 61000 6 2 2005 Weitere Informationen 2 B Dokumente Pr fberichte Einschr nkun
8. 0 V 1 Check that the device is switched off 2 Plug the power cable into the power connection jack 5 3 Plug the power cable into a grounded socket Danger Danger to life and limb from power supply gt Do not open the device casing after connecting the printer to the power supply 2 3 2 Installation Connecting to a Computer via USB Attention Inadequate or no grounding can cause malfunctions during operations gt Ensure that all computers and cables connected to the printer are grounded In order to connect the printer to a USB interface a printer driver must be installed The adequate driver for your device can be found on the DVD included in the contents of delivery or on the internet at www phoenixcontact net catalog Switch on computer gt Terminate all running tasks gt Switch on THERMOMARK CARD Attention Danger of crushing gt Pay attention to the transport slide which retracts automatically if it is extended when initializing the printer v Connect computer with THERMOMARK CARD using the included USB cable Insert DVD with the driver software into the DVD drive The Windows installation wizard is started automatically Follow the instructions on the screen When the error message Windows logo test failed appears still continue the installation After a successful installation an icon for the THERMOMARK CARD appears in the windows system directory Printer
9. CONTACT 104612_en_02 Note on the print media The result of the print depends essentially on the suitable combination of material and print ribbon NOTE Use suitable print media A low quality ink ribbon can lead to premature wear on the printhead and result in a poor print image Use only print media from Phoenix Contact You can find suitable print media in the Phoenix Contact catalog Change language of Touch Screen The language of the Touch Screen is set to English by default To select a different language proceed as follows e Touch FR to open the menu e Select then for the settings e With I you access the regional settings e Touch the symbol e Usethe horizontal arrows to select your language e Confirm your selection with E d s e Touch p to return to the menu 104612_en_02 PHOENIX CONTACT IV Technical data Resolution Print mode CPU Material sensor Print speed Print length Print width Print medium Maximum width Maximum length Ink ribbon Length Outside diameter of the ink ribbon reel Internal core diameter Ink side Interfaces Display and Operation Voltage Power Temperature Operation Storage Transport Humidity Operation Storage Transport Approvals Dimensions H x D x W Weight 300 dpi x 300 dpi 12 points mm x 12 points mm Thermal transfer 32 bit 400 mHz Sensor for US media and UCT media 30 mm s 75 mm
10. HLAND EZ 10 Index B Button Function 17 Cleaning Instructions 26 Printhead 27 CLIP PROJECT 14 Connecting 13 Contents of Delivery 12 Correctable error 18 Critical fault 18 D Device Overview 11 E Environment 10 Errors Correction 29 Messages 29 Ethernet Interface Configure 20 Important information 8 Insert Magazine 22 Instructions 8 Intended Use 9 L Lithium Battery 10 Loading Material 21 Loading Transfer Ribbon 21 M Modifications 10 Power Save Mode 19 Power Supply 13 Printer States Printhead Cleaning 27 Damage 23 Problem Solution 29 R S Safety Instructions 9 Service Work 10 Setting up 12 Supply Voltage alld Switching on the Device 15 System Error 29 T Test Print Touchscreen Display Transfer Ribbon Feed Path 21 U UCT magazine 1 22 UCT material 23
11. Test Print 20 Unpacking 12 US magazine Insert 22 US material Insert hue Test Print Warning Stickers 10
12. all be regarded as improper use The manufacturer supplier shall not be liable for damage resulting from unauthorized use the user shall bear the risk alone Usage for the intended purpose also includes complying with the operating manual including the manufacturer s maintenance recommendations and specifications Notice The complete documentation is included in the scope of delivery on DVD and can also currently be found in the Internet 1 4 Safety Instructions The device is configured for voltages of 100 to 240 V AC It only has to be plugged into a grounded socket Only connect the device to other devices which have a protective low voltage Switch off all affected devices computer printer accessories before connecting or disconnecting The device may only be used in a dry environment do not expose it to moisture sprays of water mists etc Do not use the device in an explosive atmosphere Do not use the device close to high voltage power lines If the device is operated with the cover open ensure that people s clothing hair jewelry etc do not come into contact with the exposed rotating parts The device or parts of it can become hot while printing Do not touch during operation and allow to cool down before changing material and before disassembly Risk of crushing when closing the cover Touch the cover at the outside only Do not reach into the swivel range of the cover Perform only those actions describ
13. e printer will issue an error message If the material is inserted correctly the print is started After printing the transport slide is extended until the extract position is reached Remove material Insert new material Repeat procedure until the print job is processed completely Select O to re print the previous page of the print job 736 Cleaning 6 1 Cleaning Instructions Danger Risk of death via electric shock gt Disconnect the printer from the power supply before performing any maintenance work It is important to clean the thermal printhead regularly This guarantees a consistently good printed image and reduces wear of the printhead Otherwise it is recommended to clean the device once a month Attention The printer can be damaged by aggressive cleansers gt Do not use abrasive cleaners or solvents for cleaning the external surfaces or modules Note eb If the device is not in use shut the cover to avoid soiling Remove dust and paper fluff from the print area with a soft brush or vacuum cleaner gt The cover of the printer can be cleaned with a standard cleanser 6 Cleaning 6 2 Cleaning the Printhead Attention Printhead can be damaged gt Do use sharp or hard objects to clean the printhead gt Do not touch protective glass layer of the printhead Attention Risk of injury from the hot printhead line gt Ensure that the printhead has cooled down before starting clea
14. e ribbon core 3 using adhesive tape Ensure counterclockwise rotation direction of the transfer ribbon take up hub 6 Turn transfer ribbon take up hub 1 counterclockwise to smooth out the feed path of the transfer ribbon 744 Loading Material 4 2 Insert Magazine Note e It is not necessary to switch off the printer when changing the magazine Attention Risk of crushing gt Make sure that there are no body parts or objects within the range of the slide when extending and retracting the transport slide gt Extend transport slide with 9 Insert UCT magazine P Place magazine with holes onto the pins 1 of the transport slide Position magazine a way that the holes 2 at the magazine s edge are at the rear left Fig 6 Insert UCT Magazine Insert US magazine Place magazine with the holes onto the pins 1 of the transport slide Fig 7 Insert US Magazine 5 Printing Operation Attention Printhead damage caused by improper handling gt Do not touch the underside of the printhead with the fingers or sharp objects gt Ensure that the cards are clean The printer is ready for operation when all connections have been made and cards and the transfer ribbon have been loaded Attention gt Unlock the transport lock before inserting and printing the material gt 7 1 on page 28 Start print job If the transport slide is not in the insert position select e to extend
15. ed in this operating manual Work going beyond this may only be performed by trained personnel or service technicians 491 Introduction A Unauthorized interference with electronic modules or their software can cause malfunctions Other unauthorized work on or modifications to the device can also endanger operational safety Always have service work done in a qualified workshop where the personnel have the technical knowledge and tools required to do the necessary work There are various warning stickers on the device They draw your attention to dangers Warning stickers must therefore not be removed as then you and other people cannot be aware of dangers and may be injured The maximum sound pressure level is less than 70 dB A Danger Danger to life and limb from power supply gt Do not open the device casing 1 5 Environment Obsolete devices contain valuable recyclable materials that should be sent for recycling gt Send to suitable collection points separately from residual waste The modular construction of the printer enables it to be easily disas sembled into its component parts P Send the parts for recycling The electronic circuit board of the device is equipped with a lithium battery P Take old batteries to collection boxes in shops or public waste disposal centers 2 Installation 2 1 Device Overview Fig 1 Device Overview
16. en Display 16 Structure of the Touchscreen 16 Operating the Touchscreen 16 Symbols on the Start 17 PrinterSIatesu rein Pee 18 Configure Ethernet 20 Perform Test Print eese reete ret ERE rH 20 Loading Material eese nennen 21 Loading Transfer Ribbon 21 ERE 22 Printing Operation eese 23 Lu ue 26 Cleaning Instructions 26 Cleaning the Printhead 27 Transport L k 28 Unlock Transport 28 Prepare Device for 28 Fault Correction 29 Problem Solution een 29 Error Messages and Fault 29 Licences 31 EC Declaration of Conformity 31 uoo 33 GPL Code Statement 33 34 551 Introduction 1 1 Product Description The device is an indust
17. gen etc zur Konformit tsbewertung Additional information example documents test reports restrictions of the confomnity assessment Zertifikate einer benannten Stelle Certificates by a notified body Anschrift Address Referenz Reference Anschrift Address Referenz Reference Die letzten beiden Ziffern des Jahres in dem die CE Kennzeichnung angebracht wurde 11 The last two figures of the year in which the CE marking was applied a nur einzutragen bei der Niederspannungsrichtlinie only to be entered on the low voltage directive Diese Erkl rung gilt auch f r die im Anhang aufgelisteten Produkte wenn angekreuzt This declaration also applies for the products listed in the annex if marked with a cross Diese Erkl rung bescheinigt die bereinstimmung mit den wesentlichen Anforderungen der genannten Richtlinie n enth lt jedoch keine Zusicherung von Eigenschaften Die Sicherheits und Einbauhinweise der mitgelieferten Produktdokumentation sind zu beachten dogs however This declaration certifies the conformity with the essential requirements of the indicated directive s it characteristics The instructions for safety and installation of the enclosed product documentatior tiave fo be obsery d j i _ eeu Blomberg 2011 12 16 5 aul L vl fa _ 2 Sandra Klocke F irk G rlitzer Business Unit Industrial Connection Technolo
18. gy Business Unit Industrial Connection Technology Head of Development PM MARKING system Vice President Head of the Business Unit ZefChnungsberechtigter authorized signatory Ansprechpartner person Formblatterstelldatum Formblattersteller FS A 7 0037 09 DEI 2011 08 20 pail coer abled Corporate Technology Blatt Page 1 von of 2 5146464 CE 01 doc 9 Licences PHCENIX CONTACT 5146464 CE 01 Anhang zur EG Konformitatserklarung Annex on EC Declaration of Conformity vom dated 2011 12 16 Produktbezeichnung Product description THERMOMARK CARD Artikelbezeichnung Article description Artikel Nr Article no 5146464 Die Konformit t mit den wesentlichen Anforderungen der Richtlinie n wird auch f r folgende Produkte bescheinigt The conformity with the essential requirements of the directive s is also certified by the declaration for following products Artikel Nr Article no Artikelbezeichnung Articie description 5146736 THERMOMARK CARD AR 5146464 CE 01 doc Blatt Page 2 von 2 9 3 Licences FCC NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment The equipment generates uses and can radiate radio fre
19. ions of Phoenix Contact apply exclusively in particular as concerns any warranty liability This manual including all illustrations contained herein is copyright pro tected Any changes to the contents or the publication of extracts of this document is prohibited Phoenix Contact reserves the right to register its own intellectual property rights for the product identifications of Phoenix Contact products that are used here Registration of such intellectual property rights by third parties is prohibited Other product identifications may be afforded legal protection even where they may not be indicated as such 104612_en_02 PHOENIX CONTACT ii Internet Subsidiaries Published by How to contact us Up to date information on Phoenix Contact products and our Terms and Conditions can be found on the Internet at www phoenixcontact com Make sure you always use the latest documentation It can be downloaded at www phoenixcontact n tal If there are any problems that cannot be solved using the documentation please contact your Phoenix Contact subsidiary Subsidiary contact information is available at www phoenixcontact com PHOENIX CONTACT GmbH amp Co KG FlachsmarktstraBe 8 32825 Blomberg GERMANY Should you have any suggestions or recommendations for improvement of the contents and layout of our manuals please send your comments to t hoenixcontact com iii PHOENIX
20. ning Fig 17 Printhead line 1 Remove magazine material and transfer ribbon from the printer 2 Clean printhead line 1 with a felt stick CLEANING STICK Part No 5146698 soaked in rubbing alcohol 3 Allow printhead to dry for 2 3 minutes before commissioning the printer 737 Transport Lock 7 1 Unlock Transport Lock TUS Fig 18 Transport lock Unlock Transport Lock gt Open cover gt Move transport lock 1 until the arrow points to the symbol transport slide 7 2 Prepare Device for Transport Remove magazine gt Lift magazine up from transport slide Lock transport lock gt Open cover gt Move transport lock 1 until the arrow points to the symbol transport slide Remove transfer ribbon E on the lon the gt Remove transfer ribbon from transfer ribbon supply hub and transfer ribbon take up hub 8 Fault Correction 8 1 Problem Solution Problem Cause Remedy voids Print image has smears or Printhead is dirty Clean the printhead Printer transports cards but does not print them incorrectly Transfer ribbon inserted Check transfer ribbon feed path and orientation of the coated side and correct if necessary Clean the printhead Table 3 Problem Solution 8 2 Error Messages and Fault Correction Error message Cause Remedy Buffe
21. perating the printer in a network Contact your network administrator if required IP address Subnet mask if necessary gateway Alternatively the Ethernet configuration is also available via DHCP server In this case make sure that the transmitted configuration is always the same Configure Ethernet interface at the printer 3 6 gt Select I Select Setup Select Interfaces Select Ethernet Select setting options Select desired setting with gt 4 v Confirm selection with or cancel selection with Return to start screen with Perform Test Print gt gt gt gt Select Select 6 Depending the inserted material select or FEN Test print starts 4 Loading Material 4 1 Loading Transfer Ribbon 1 Fig 5 Transfer Ribbon Feed Path 1 Clean the printhead before loading the transfer ribbon 2 Load transfer ribbon 2 on the hub 4 until it reaches the guide in a way that the color coating of the ribbon faces the opposite side of the printhead after being loaded Notice Q To wind the ribbon a ribbon core 3 is needed that must be at least equal in width to the supply ribbon gt When changing the transfer ribbon use the empty supply ribbon core for winding the next ribbon 3 Push ribbon core on the ribbon take up hub 1 4 Guide transfer ribbon though the printing unit as shown in Fig 5 5 Secure starting end of the transfer ribbon to th
22. quency and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communica tions Operation of this equipment in a residential area is likely to cause harmful interference in which case the user may be required to correct the interference at his own expense GPL Code Statement This product includes software code developed by third parties including software code subject to the GNU General Public License GPL or GNU Lesser General Public License LGPL As applicable the terms of the GPL and LGPL and information on obtaining access to the GPL Code and LGPL Code used in this product are available to you at http www phoenixcontact net catalog under the description of the printer The GPL Code and LGPL Code used in this product is distributed WITHOUT ANY WARRANTY and is subject to the copyrights of one or more authors For details see the GPL Code the LGPL Code for this product and the terms of the GPL and LGPL Written Offer to GPL Source Code Whereas such specific license terms entitle you to the source code of such software PHOENIX CONTACT will provide upon written request via email and or traditional paper mail the applicable GPL source code files via CD ROM for a nominal cost to cover shipping and media charges as allowed under the GPL and LGPL Please direct all inquiries to PHOENIX CONTACT GmbH amp Co KG Flachsmarktstra e 8 32825 Blomberg DEUTSC
23. r overflow The input buffer memory is full and the computer is still transmitting data Use data transmission via protocol preferably RTS CTS Head too hot Printhead is overheated After pausing the print job will be continued automatically If the fault recurs repeatedly reduce the heat level or the print speed via software setup voltage error Memory Current print job contains Cancel current print job overflow too much information e g Reduce amount of data to be selected font large graphics printed Network e g No DHCP server no Please contact your network Error link no SMTP server no administrator Timeserver Out of Out of transfer ribbon Insert new transfer ribbon ribbon Transfer ribbon melted during Cancel current print job printing Change the heat level via software Clean the printhead Load transfer ribbon Restart print job Protocol Printer has received an Select Ignore to skip the error unknown or invalid command command or from the computer select Cancel Job to cancel the print job System Error e g FPGA defective invalid Switch the printer off and then on Please note error details shown on the display If error recurs call service BE Fault Correction Error message Cause Remedy Wrong The inserted material does Insert correct material terial t dto th t iun RUE VER EDT Select different material in the
24. rial thermal transfer printer for printing cards which are inserted into the printer with a magazine on a slide 1 2 Instructions Important information and instructions in this documentation are designated as follows e amp Time Danger Draws your attention to an exceptionally grave impending danger to your health or life Warning Indicates a hazardous situation that could lead to injuries or material damage Attention Draws attention to possible dangers material damage or loss of quality Notice Gives you tips They make a working sequence easier or draw attention to important working processes Environment Gives you tips on protecting the environment Handling instruction Reference to section position illustration number or document Option accessories peripheral equipment special fittings Information in the display 1 Introduction 1 3 Intended Use The device is manufactured in accordance with the current technological status and the recognized safety rules However danger to the life and limb of the user or third parties and or damage to the device and other tangible assets can arise during use The device may only be used for its intended purpose if it is in perfect working order and it must be used with regard to safety and dangers as stated in the operating manual The device printer is intended exclusively for printing suitable materials Any other use or use going beyond this sh
25. s Maximum 140 mm Maximum 104 mm 115mm 164 mm Maximum 300 m Maximum 68 mm 25 4 mm Outside USB 2 0 full speed slave Ethernet 10 100Base T Touch display with 160 x 255 pixels 96 31 mm diagonal 100 V AC 240 V AC 50 60 Hz PFC Maximum 100 W 5 C 35 C 0 C 60 C 25 C 60 C 10 85 no condensation 20 80 no condensation 20 80 no condensation 5146464 CE FCC class A UL CB 5146736 CE FCC class A UL CB S Mark 189 mm x 320 mm x 253 mm 6 5 kg V PHOENIX CONTACT 104612 en 02 Table of Contents CE X A akhWN dnigvueltiui mp 8 Product Description 8 amp c 8 intended USE c eae vacates 9 Safety Instructions irent 9 Environment 10 11 yere 11 Unpacking and Setting up the 12 Connecting the 13 Connecting to the Power 13 Connecting to a Computer via USB 14 Connecting to a Network via 15 Switching on the Device 15 Touchscre
Download Pdf Manuals
Related Search