Home

M5100-PR & M5208 USB 3.0 Duplicator User Manual

1. Figure 4 13 Editing a job for CDROM partition Note that in contrast to the previous example the operation Set LUN is not required since the USB device will only contain one drive Also it is presumed that the user has created an ISO Image for the USB drive and that this image is in one binary file on the M5100 PR The first USB Controller operation is set up as below Figure 4 14 to create one LUN a Select SMI3255AB b LUNO will be checked as default c Setthe LUN type to RW The LUN must remain Read Writeable in order to load the ISO Image d Choose if the Drive should be configured as removable or a fixed Drive e Setthe size of the LUNO If the value 0 is not changed the entire capacity of the Drive will be used f Clear CD ROM Partition by checking this box any existing CD ROM Read Only Partition on a USB Drive will be deleted 91 M5100 USB 3 0 amp USB 2 0 DUPLICATOR Yu USB Controller wBYow _ P RAIA Figure 4 14 USB Controller Setting In the second USB Controller operation LUNO is set to CD ROM All other settings remain the same as in OP1 as shown in Figure 4 15 USB Controller v oe n Figure 4 15 CDROM Setting After saving and executing the job the target USB Drive will contain one partition with the entire capacity being a Read Only CD ROM Drive No data can be added or deleted from the USB Drive 52 M5100 USB 3 0 amp USB 2 0 DUPLICATOR Example 3 Remo
2. cccccccccccececececececececucecucucucucucacacauaucuauauauauauauaunenenes 41 SJA OLOPE iei aa A a E A a 42 SEPE AD OTS A A A E A E E EAS AS 42 396 Enter JOD FO NUMDEI saene aaa 43 3 10 F lly Loaded Un osere rsa a aaa Anaa Eaei 43 4 M5100 PR Special Features inunda 44 4 1 Barcode Launch OF GODS csccctenczsceenosboctaterethbdieiaeatiendddnnicuhtecbenenatebbiatadatteccddabiasaseatebevatebOneaes 44 4 2 Module Serial NUMDET c ccccccceccccececececcececsceccucececsccecusecseauausecscaeaucunecseauausenseasans 45 4 3 Creation of CDROM or Read Only LUNs on USB drives ccooccccccoccncccccccncoconcnccconcninonos 48 44 USB Serial Number Generation cccccccccecececcececececcecececcececececueaeuececaueaesecscauauaensceeass 53 4 4 1 Serial Number Generation cccccccecececcccecccccccececcecececscacaeuecececcuaenecscauaeuerscanass 53 4 4 2 Writing Serial Numbers to the USB drives coccccooonccnccccnonccnncccnonccnncnonanccnncnnnancons 56 5 M5100 PR Calibration cccccccecsccccncececcncececenceseneececeneeceeeneeeeceneneeceneeseneseeasneass 58 CUSTOMER SUD DOM ciso 58 Appendix M5100 PR Software Release History oooocccooconcccoconccconanoncnnanonnnnannnnnns 59 M5100 USB 3 0 amp USB 2 0 DUPLICATOR 1 Introducing the M5100 PR Duplicator This manual is intended to be used for the following IMI USB duplicators M5100 PR M5116 PR M5132 PR amp M5208 Although the
3. menu Then click the icons New Job or Edit Job in the Job List window New Job and Edit Job options are also available under the File pull down menu The job editor window will open up as shown in Figure 3 18 we M51W Job Editor TDR File B New 7 Open lH Save LA Save As Te Exit Current Job home user imi jobs Master_verify mlj Description Available Operations Current Job Operations a Selected Operation Details Remove All Edit Remove Program Datasource Master Verify Start Address Start Op 1 Set Values End Address End Proagram Verif 7 Address Mode Megabyte _ 9 y Op 2 Verify Address Base Base 10 Decimal Create Master File Quick Verify No Skip Verify Error No Create Master Pattern Erase Smart Program Smart Verify Smart Program Verify insert Smart Create Master File Constraints Smart Erase File Copy File Verify File Copy Verify USB Controller Set LUN v _ Fully Loaded Check Figure 3 18 M51W Job Editor A M5100 PR Job created in the M5100 PR GUI is a sequential list of operations as defined in the M5100 PR GUI Job editor The available operations for this list are shown on the left column of the Job Editor screen shown in Figure 3 18 The current list of job operations is shown in the middle of the Job Editor screen Operations are added deleted etc using the buttons between the available operation list
4. ACERTO TA EIE The VERIFY MODE by default is set to BINARY If you wish to do a FAST VERIFY press the MODE key to choose FAST mode The MODE key toggles between BINARY and FAST modes and the Green LED above the MODE key lights up indicating the mode as BINARY or FAST Press the Green START button to start the verify operation The data in the target drives will be verified bit by bit against the master drive The following screens on the LCD show the different steps in the copy amp verify operation and indicate that the copy amp verify is in progress 12 M5100 USB 3 0 amp USB 2 0 DUPLICATOR TOS hs Ecce Checking Webs O RU Op2 Verify ZENS 10 Ml 0S COZ 8 Weel icy 246 0M 58 6 Upon completion of the Verify job a summary screen with pass and fail results is displayed The summary screen also displays the Master drive checksum which is the simple sum of all bytes in the master drive that have been copied to the target drive MASTER CSUM A amp 8500000 215 15 1 00 00 2 7 FORMAT amp ERASE using the M5116 PR 1 Insert up to 15 target drives on the copy slots labeled 1 15 2 Press FORMAT key to select Erase amp Format function The Green LED above the FORMAT key lights up indicating that the selected function is FORMAT The LCD screen also displays the selected function as shown below ACTION ERASE FORMAT 3 The FORMAT MODE by default is set to BINARY If you wish to do a FAST FORMAT press the MODE
5. 2 Press the DOWN key to select a specific job 3 Once the desired job is selected press the START key to run the job The default jobs that are available under the Run Job menu are as below 14 M5100 USB 3 0 amp USB 2 0 DUPLICATOR Create Master File Create a binary image file of a master data source The output file name of the master image file should use a bin extension File Copy Copy from a defined file to target USB drives File Copy_Verify Copy a specifed file to target USB drives and then verify the target drives against the file File_Verify Verify bit for bit the target drives against a file Master_Copy Copy the entire master drive to the target drives Master_Copy_Verify Copy the entire master drive to the target drives and then verify the target drives against the master drive Master_Verify Verify bit for bit the target drives against the master drive Smart_Copy Copy only the sectors with data and skip the blank sectors Smart Copy is supported for FAT FAT 32 NTFS exFAT File systems An additional license is available to support Smart Copy for HFS EXT2 EXT3 amp EXT4 file system formats Smart_Copy_Verify Copy only the sectors with data and skip the blank sectors and then verify the copied data Smart_Verify Verify bit for bit the programmed data SmartCreateMasterFile Create a smart master file by analyzing the data source for FAT FAT 32 NTFS HFS EXT2 EXT3 amp EXT4 file systems in order
6. CARD READER SUPPORT USB card readers can be used to read write flash memory media such as SD cards MicroSD cards CF cards on the M5100 PR Most USB adapters can be used with the M5100 PR However IMI cannot guarantee that all readers will work with all types of inserted flash media For successful duplication all USB adapters should be the same manufacturer and model and all flash memory devices Master and Copy drives should be from the same manufacturer and be of the same type and size if possible purchased in trays M5100 USB 3 0 amp USB 2 0 DUPLICATOR 2 Using the M5100 PR Duplicator Stand Alone 2 1 M5100 PR Power up 1 Attach the provided AC power cord on the side rear of the unit and connect it to an electrical outlet 2 Press the Green power button located above the AC input on the side rear panel of the M5100 PR 3 After the power is turned on the M5100 PR takes about a minute to configure the machine place its power up screen on the LCD screen and sound a short sequence of five notes Once the unit is booted the top line of the LCD screen displays the current software version of the M5100 PR and the second line of the LCD shows the current menu function that can be selected using the START key MS Oda SW Ver A 2 RUN JOD y 4 The M5100 PR is now ready to use for duplication 2 2 M5100 PR Power Down There are three methods for shutting down the M5100 PR Shut Down Method 1 The M5100 PR can
7. These menus are listed in the sections below 3 2 1 File Menu Figure 3 4 File Menu Create a new job script supervisor mode Edit a job script supervisor mode View log statistics in database Exit the GUI 23 M5100 USB 3 0 amp USB 2 0 DUPLICATOR 3 2 2 Connection Menu Figure 3 5 Connection Menu The Connect to Server menu enables the M51W GUI to connect to the server when the server is disconnected When the server is disconnected the rectangular slot icons are not displayed and a SERVER DISCONNECTED message is displayed as shown in Fig 3 6 Bo USB Duplicator International Microsystems Inc wow Figure 3 6 Server Disconnected 3 2 3 Admin Menu Change Operation Mode to Operator or Supervisor requires password The default password to switch to supervisor mode is 123456 24 M5100 USB 3 0 amp USB 2 0 DUPLICATOR 3 2 4 Tools Menu Tools ia Barcode Help m Update Create Master File Checksum Master Device Set Operator ModuleSerial Number KOSI M Enter Job PO Number Figure 3 8 Tools Menu Update software from inserted Master device Create Master File from inserted Master device Run Checksum of Master device Set the Name of the Operator Enable or Disable Module Serial Number Enable or Disable Barcode Enable or Disable Kiosk Mode Enter Job PO Number Please refer to Section 3 9 for detailed description of the above menu funct
8. l vidipid licenses vid number m ia number C Figure 4 22 Writing Serial Number Job 6 Execute this job Once the job has run successfully click on the Green USB slot icon to see the new serial number written to the USB device The screenshot below shows the Serial number created as per the Example serial generator file created in the previous section es wy Device Information M5200M y amp Slot 1 Vendor Product ID 090C Rev 300000 Serial Number IMI20130829145644 PS TOANE Manufacturer SMI Corporation Md Sal y Se Ose ee SRE Figure 4 23 New Serial Number 57 M5100 USB 3 0 amp USB 2 0 DUPLICATOR 5 M5100 PR Calibration IMI duplicators do not need to be calibrated after purchase by the customer The voltages applied to the memory devices being duplicated are checked internally during the normal operation of the instrument An Initial calibration certificate can be provided on request at the time of the purchase only The certificate request must be indicated on the purchase order and will require an additional 50 fee 6 Customer Support To obtain service or technical support for your system please contact IMI Technical support department at 408 942 1001 or visit www imi test com for web support 98 M5100 USB 3 0 amp USB 2 0 DUPLICATOR Appendix M5100 PR Software Release History LOL LS Eo Fixed ScanUsb function to detect inserted usb device Nee
9. or a smart binary image file 41 M5100 USB 3 0 amp USB 2 0 DUPLICATOR Bw Calculate Master Device Checksum www Figure 3 34 Calculate Master Checksum Once the user clicks on the OK button the checksum results are displayed as shown in Figure 3 35 Sw Information slice 127 0 0 1 63 wy y gy i i Master File Information For Slice 127 0 0 1 Lun 0 Size of Area Summed 104 857 600 100 0 MB CheckSum F9D88DD6 CRC32 9F27A9B8 MD5 Hash 8160401EDE6CBO669B05C1CAF2B9A1F2 SHALI 68FOA63B2283AFO6BAA7DF9576E4AFE32E7BFCO9 Device Size 2 013 265 920 1 9 GB Figure 3 35 Master Checksum 3 9 4 Set Operator This option is used to set the name of the operator using the duplicator Bw Operator B Y y w ied r gt wie vam Y a ne VE F ait jt bap A cal mt N Figure 3 36 Set Operator 3 9 5 Barcode Please refer to Section 4 1 on how to use this feature 42 M5100 USB 3 0 amp USB 2 0 DUPLICATOR 3 9 6 Enter Job PO Number This option is used to enter the Job and PO if any for the jobs run in the duplicator es y Enter Job and PO Number wy xX job Number 0 PO Number 0 8 ok Cancel mM e o _ Figure 3 40 Job PO 3 10 Fully Loaded Check A common fault in manual duplication is that the user fails to fully insert a USB device and hence the duplicator does not recognize the USB device Then after completion of the operation the non recognize
10. 3 3 1009070811022212 2013265920 2316 4096 Passed 122 Figure 4 9 Module Serial Number Database Log 47 M5100 USB 3 0 amp USB 2 0 DUPLICATOR 4 3 Creation of CDROM or Read Only LUNs on USB drives The M5100 PR supports creation duplication of USB drives manufactured with specific controllers with CDROM or Read only LUNs or partitions Please check with IMI Sales for the list of controllers supported by IMI for this feature Below are examples for creating multiple partitions with different attributes on a USB drive with an SM3255AB controller In these examples the references LUN and Partition are used interchangeably Example 1 Two LUN s with LUNO R W and LUN1 Read Only The goal in this example is to create a USB drive SMI3255AB controller with two LUN s LUNO Standard Read Write Partition LUN1 Read Only Partition To achieve this create a test job with the following job commands as shown in Figure 4 10 ie e MS1W Job Editor JOE File _ New A Open lH Save Al save As f Exit Current Job New job Description Available Operations __ Current Job Operations Selected Operation Details Create Master File by Parameters Remove All Edit Remove Create Master Pattern SMI3255AB 57 Controller Erase hth Op 1 USB Controller Type RW and Removable Size 200 MB Smart Program Op 2 Set LUN LUN 1 Smart Verify Op
11. 5 X 11 X 15 5 M5116 PR 12lbs Weight M5132 28 Ibs M5208 12 Ibs Power Supply 100 250 VAC 300W perating Temperature 40F 120F 1 3 Package Contents gt M5100 PR USB Duplicator gt AC Power Cord gt M5100 PR User Manual 1 4 Things to remember gt MASTER SLOT The master slot is the very first slot also marked as MASTER gt DEVICE LED DETECTION The Green LEDs above each USB port will flash as soon as a USB device is inserted and recognized by the M5100 PR gt BUSY SIGNAL The Green LEDs above each USB port will flash when the duplicator is in use and will stay solid Green after a successful duplication gt RED LED MEANS FAIL If the duplication is not successful it is indicated by a solid Red LED above the failed USB device M5100 USB 3 0 amp USB 2 0 DUPLICATOR gt SAME DEVICES EQUALS SUCCESSFUL DUPLICATION Although many USB devices from different manufacturers may be branded with the same size say 512 MB in reality they may have a slightly different number of sectors or total number of bytes IMI highly recommends that the user only duplicate from master devices that are the exact same type and manufacturer as the copy devices gt CLEAN THE MASTER DEVICE BEFORE COPY When creating a device to be used as a master for duplication IMI recommends that the device designated to be the master should be reformatted and or erased before copying files over to it to make the master gt
12. 6 Upon completion of the copy job a summary screen with pass and fail results is displayed The summary screen also displays the Master drive checksum which is the simple sum of all bytes in the master drive that have been copied to the target drive 10 M5100 USB 3 0 amp USB 2 0 DUPLICATOR In the summary screen below all the 15 devices passed the Copy job and there are no failures MASTER CSUM A amp 8500000 Pels Ls FeOO OC In case of any failures during the copy the summary screen will look as below Here 14 devices passed the Copy and one device failed Click the DOWN arrow to see the error message of the failing device The error message displays the Slot and the failure message MASTER CSUM A8500000 Pola Ss PoC Oe NY Palas WeoLy oc gt 1 Device Size Error 2 5 COPY VERIFY using the M5116 PR 1 Insert the master drive on the master slot and up to 15 target drives on the copy slots labeled 1 15 2 Press COPY VERIFY key to choose copy amp verify function The Green LED above the COPY VERIFY key lights up indicating that the selected function is COPY VERIFY The LCD screen also displays the selected function as shown below ANGI IVOIN E COI Cy GIS IL let XC 3 The COPY amp VERIFY MODE by default is set to BINARY The BINARY LED Lights after the COPY VERIFY Key is depressed If you wish to do a FAST COPY VERIFY press the MODE key to choose FAST mode The MODE key toggles between BINARY and FAST m
13. are 512 Byte units Address Mode Megabytes selection means that the displayed Start and End addresses are the LBA or Logical Block Address megabyte units Address Base The different address base options that are available are Base 16 hex and Base 10 decimal Normally if the Address Mode is linear the Address Base is hex If the Address Mode is Sectors Megabytes the Address Base is decimal Address Start amp Address End Set the Start LBA address and End LBA address for the operation Data Source The different data source options that are available are are a Master device in the Master socket a Binary File or a Pattern Depending upon the user choice different parameters may be set Master Device No choices File The Browse button is enabled and the user may browse the file system for the file or write the file name into the File name box Pattern The Pattern Type choice list is enabled TR3 The data used is generated by the M5100 PR Each byte value is equal to the 8 hex digit sum of the LBA byte address This is a good pattern for testing 32 M5100 USB 3 0 amp USB 2 0 DUPLICATOR NTR3 The data used is generated by the M5100 PR Each byte value is equal to the 8 hex digit sum of the two s complement of the LBA byte address This is a good pattern for testing Fixed A fixed eight digit hex number is used for the copy data eg FFFFFFFF Constraints Size If this box is checked a choice list is enabled Tar
14. based on the values set in the preceding Set value operation 34 M5100 USB 3 0 amp USB 2 0 DUPLICATOR 3 7 6 Create Master File Create Master File operation is used to create a binary image file of the USB device in the Master slot The user needs to provide the name and path of the master image file as shown in Figure 3 22 below je Required Values 2 iw Wy es Create Master File Parameters Master File Name Browse OK Cancel Figure 3 22 Create Master File Screen 3 7 7 Erase Erase operation programs the data pattern FFFF to the entire device and erases it The user can perform a verify after an erase by checking the verify check box in the erase operation as shown in Figure 3 23 below Je 3 Erase Ww wy o A Verify W OK Cancel Figure 3 23 Erase Screen 3 7 8 Smart Program Smart Program operation uses an IMI proprietary algorithm to copy only the sectors with data and skip the blank sectors 3 7 9 Smart Verify Smart Verify operation verifies the data copies using the Smart Program operation 3 7 10 Smart Program Verify Smart Program Verify operation performs a smart program followed by a smart verify 3 7 11 Smart Create Master File This operation is used to create a smart master file by analyzing the data source for FAT FAT 32 NTFS HFS EXT2 EXT3 8 EXT4 file systems in order to omit unused areas in the memory and create a smaller master image file 3 7 12 Smart Erase Smart
15. e Fixed keyboard function keys not having a default when entered after using Run Job menu selection e ESC key from results menu to return to menu after job run from Run Job menu 4 12 13 4 10 13 1 09 e Turned off the keypad LED when the server start e Turned off the keypad LED when the GUI is connected e Fixed not to get the read only information of the devices during scanning e Fixed bug in job creation for standalone Fixed memory leakage Fixed the keypad firmware V1 06 a e Fixed server to work with GUI e Fixed bug in logging which may not log the serial number properly e Changed not to use proc bus usb devices e Changed to use libusbl 0 e Fixed bug in Erase when the address 1s specified in number of sector e Fixed bug in Smart operation with EXxFat e Fixed bug in requesting serial number from generator Zp Zi E La OG e Added beep when Abort is hit e Clear the Chksum when job is aborted e Added checking the hardware when the M5100 USB 3 0 amp USB 2 0 DUPLICATOR server is started If any error display it Added duplicator Error information in the information menu AS 1 05 Checked or the number Of 2 00 320 hub appears during init Fixed bug in the Information in the LCD display After duplication is done ESC key brings up the menu and the operation LED will be turned off The total number of pass fail will be cleared when any key except the ENTER key is hit Added the error messag
16. key to choose FAST mode The MODE key toggles between BINARY and FAST modes and the Green LED above the MODE key lights up indicating the mode as BINARY or FAST 4 Press the Green START button to start the FORMAT operation During FORMAT all the memory locations in the USB drives will be written with FF pattern followed by a format 5 The following screens on the LCD show the different steps in the FORMAT operation 13 M5100 USB 3 0 amp USB 2 0 DUPLICATOR JOO Ses ae Checking Job Setup JOO Sa 4e 246 UO OM JONS O NOA 6 Upon completion of the format job a summary screen with pass and fail results is displayed MASTER CSUM 00000000 PLLs LS WeOO OC 2 8 Menu Functions on the M5116 PR The following menu functions are available from the LCD screen on the M5100 PR The DOWN key allows the user to select the function and execute them and the MENU key allows the user to return to the top menu function Run Job Result Save Log Information Software Update Restart Server Shut Down oe eh 2 8 1 Run Job The Run Job menu presents a list of currently defined jobs in the default job directory nome users scripts defaults The front panel job list can be created and edited using the M51W GUI Please refer to Chapter 3 for more information on how to create edit the jobs using the M51W GUI To select a job from the job list under Run Job menu 1 Press the START key when Run Job is displayed on the LCD screen
17. o 3 BINARY FAST y o O MODE Figure 2 1 M5116 Keypad The following keys are available on the M5100 PR keypad and their functions are described below COPY VERIFY Copy the entire master drive to the target drives and then verify the target drives against the master drive COPY Copy the entire master drive to the target drives No verify is executed VERIFY Verify the target drives against the master drive FORMAT ERASE Format the target drives by writing FF pattern to all the memory locations and then format the target drives The type of formatting done is based on the size of the target drives and is performed as follows gt FAT format for USB drives with capacity lt 2GB gt FAT32 format for USB drives with capacity 2GB 32GB gt NTFS format for USB drives with capacity gt 32GB See Section 2 6 for a full explanation MENU Return to the Top menu function in the LCD screen DOWN Scroll down the menu functions available on the LCD screen to select a desired function MODE Select a mode BINARY or FAST for Copy Verify amp Format Note that by default the BINARY MODE is chosen when the COPY VERIFY or FORMAT keys are pressed BINARY COPY Copies the entire master drive to the target drives BINARY VERIFY Verifies the entire target drives against the master drive 9 M5100 USB 3 0 amp USB 2 0 DUPLICATOR BINARY FORMAT Erases the target drives completely and then formats the target drives F
18. on the left and the current list in the center These buttons also allow setting the parameters and consiraints on the selected operation This is described in the following section 3 7 3 7 Available Operations for a New job in M5100 PR 3 7 1 Set Values The first entry in the list of operations available to create a new job using the M51W job editor is Set Values This is normally the first operation in every job To add this operation to your new job select the Set Values operation and click on the Add button The Set Values definition screen will now be displayed as shown in Figure 3 19 31 M5100 USB 3 0 amp USB 2 0 DUPLICATOR je Set Values Y UR Address Constraints Address Mode Megabyte v Size Address Base Base 10 Decimal v Sum Hex Address Start start id skip Verify Error Address End End Boh _ Skip Ver Error Max Error Data Source Quick Verify Data Source Master v quick verify OK Cancel Figure 3 19 Set Values Definition Screen The values chosen and defined in the Set Values Operation define how other M5100 PR operations execute their functions Address Mode The different address mode options that are available are Linear Sector or Megabyte Address Mode Linear selection means that the displayed Start and End addresses are the LBA Logical Block Address in bytes Address Mode Sector selection means that the displayed Start and End addresses are the LBA Logical Block Address sectors which
19. tcl v Fully Loaded Check Off Figure 3 2 Main M51W Window The main M51W window has two tabs Job List and Job Run The Job List tab displays the list of jobs available and the job information The job information includes the description of the job operations used for the currently selected job and the parameters constraints set for the currently selected operation on the current job In addition the Job List screen also has shortcut buttons to switch the user modes between operator amp supervisor view logs and create edit a job The Job Run tab displays the run time information of the job A screenshot of the Job Run tab is shown as below in Figure 3 3 22 M5100 USB 3 0 amp USB 2 0 DUPLICATOR roy ey l USB Duplicator International Microsystems Inc wy YY ros On n O i ei ae ae Se Ks SmartCopyMasterFile mlj ghee a 7 ard E om ise o Figure 3 3 M5116 PR Job Run Window The Job Run displays the START and ABORT keys and run time information including Job flow Progress bar pass fail information and Rectangles representing the M5100 PR USB sockets These socket icons will change color indicating insertion and pass fail status Blue for insertion Green for pass and Red for fail The job flow window indicates the flow of operation when a job is running 3 2 M51W Menu There are five pull down menus on the top of the screen namely File Connection Admin Tools and Help
20. 2012 O9 32 31 Quick Format 12 28 2012 0923522352 00000000 0 0 1 0 0 0 H5100 0 0 Position serialnum capacity vid pid status message standbyicc writespee d readspeed activeminread activemaxread activeaveread activeminwrite ac tivemaxwrite activeavewrite 0 106462120914572 257949696 1500 766 1 Passed 0 0 0 PB PO Tt 787 707 a A For Help press Fl Fig 2 3 Snapshot of Server log file To save the logs 1 Select Save Log menu and press START button AMS SA e A ONG Sawe lOc 2 After selecting Save Log the following message will be displayed on the screen Please insert the USB Drive in Master Slot Then Press Enter Please insert the USB A So 3 Place a USB drive in M5100 PR Master slot Wait for a blinking Green light over the drive and then press START key The text log files will now be copied to the USB drive Upon completion the display will go back to the main menu and read as follows AA MISS Ver 1 00 gt Save Log 17 M5100 USB 3 0 amp USB 2 0 DUPLICATOR 2 8 4 Information The information menu provides the Network information of the M5100 PR including the IP address and MAC address of the unit It also displays a status message about the hardware of the unit In case of any problem with the hardware of the M5100 PR an error message is displayed By default the message reads Mach No Error indicating ther
21. 3 Set Values Type RW and Removable Size 0 MB Smart Program Verify Op 4 Program Verify Clear CDROM partition Yes Smart Create Master File Op 5 Set LUN Smart Erase Add Op 6 Set Values File Copy iani Op 7 Program Verify File Verify Op 8 USB Controller Sonsini File Copy Verify ara Set LUN Kiosk Mode Tcl Command Format Device Check Device Config Fully Loaded Check Figure 4 10 Editing a Job for Multiple Partitions OP1 USB Controller Sets up controller and LUN s OP2 Set LUN Select LUNO OP3 Set Values Select data for LUNO OP4 Program Verify Load data into LUNO OP5 Set LUN Set up LUN1 OP6 Set Values Select data for LUN1 OP7 Program Verify Load data into LUN1 OP8 USB Controller Set LUNO R W mode amp LUN1 Read Only mode In the first step the USB Controller needs to be set up to split the drive into two LUN s a Select SMI3255AB b Select LUNO and LUN1 to create two Partitions LUN s 48 M5100 USB 3 0 amp USB 2 0 DUPLICATOR c Set the LUN type to RW The LUN s must remain Read Writeable in order to load them with data Choose if the Drive should be configured as a removable or as a fixed Drive e Set the size of the LUNO LUN1 will automatically be the sized with the remaining capacity if the value 0 is not changed f Clear CD ROM Partition by checking this box any existing CD ROM Read Only Partition on a USB Drive will be deleted o A s
22. AST COPY Copies only the FAT content of the master drive to the target drives FAST VERIFY Verifies only the FAT content of the target drives against the master drive FAST FORMAT Perform a quick format of the target drives No erase before formatting ESC Abort a job in progress or leave the current function to return to the top menu START Initiate a function 2 4 COPY using the M5116 PR 1 Insert the master drive on the master slot and up to 15 target drives on the copy slots labeled 1 15 The Green LED lights above each of the USB ports will start blinking as soon as the USB drives are inserted and recognized by the M5116 PR unit 2 Press COPY key to choose copy function The Green LED above the COPY key lights up indicating that the selected function is COPY The LCD screen also displays the selected function as shown below A ILOIN 5 COIR 6 3 The COPY MODE by default is set to BINARY If you wish to do a FAST COPY press the MODE key to choose FAST mode for copy The MODE key toggles between BINARY and FAST modes and the Green LED above the MODE key lights up indicating the mode is BINARY or FAST 4 Press the Green START bution to start the copy operation The data from the master drive will now be copied to the target drives 5 The following screens on the LCD show the different steps during the copy operation and indicate that the copy is in progress JOD WS tranca Checking Job Setup OZ 8 COD y 246 0M 58
23. M5100 PR amp M5208 USB 3 0 Duplicator International Microsystems Incorporated M5100 PR amp M5208 USB 3 0 Duplicator User Manual Version 1 3 M5100 USB 3 0 amp USB 2 0 DUPLICATOR Copyright 2012 International Microsystems Inc All rights reserved International Microsystems Inc 556 Gibraltar Drive Milpitas CA 95035 U S A Telephone 408 942 1001 FAX 408 942 1051 Email sales imi test com Website www imi test com Manual Version 1 3 on Aug 29 2013 This manual is intended to be used for the following IMI USB duplicators M5116 PR M5132 PR amp M5208 Although the manual references M5116 PR all functions and operations described apply to M5132 PR amp M5208 also Information in this manual is subject to change without notice and does not represent a commitment on the part of vendor IMI reserves the right to change the hardware and software configurations on all its products without prior notice when deemed necessary for product improvement M5100 USB 3 0 amp USB 2 0 DUPLICATOR M5100 USB 3 0 amp USB 2 0 DUPLICATOR Table of Contents 1 Introducing the M5100 PR Duplicator ccooncconncconncicnncconoconnnconnnconannnnnnronanrnnannnns 5 Tal A Oo aud sUenet Sul Vancua anne aantmnnsdallet oa iilamad dy 5 12 Technical Specifications sets eee ies eas oe Sa ak eee 6 13 Package Contents xcs cient en heed ee ies ee ee a ee a nat 6 1 4 Things to TEMOCMDEl xc dnt eather ee ee eee ee Se ae ee 6 2 U
24. Name Source Formula e y Import From File Source File File Name Browse OK Cancel Figure 4 21 Serial Import from File 7 Click OK to save the Serial file 4 4 2 Writing Serial Numbers to the USB drives Once the Serial Generator file is created follow the steps below to write the serial numbers to the USB device using the M5100 PR 1 Open the Serial Generator application and click Run button on the menu to select Run GenserialServer 2 Open the M51W GUI and create a new job to write the Serial number Define this job by adding the USB Controller operation in this job 3 Select the desired USB controller type from the drop down menu 4 Under Serial Number section check the Enable Serial number box and type the name of Serial Generator file you created using the Serial Generator GUI 5 Click OK to save this job A snapshot of this job set up is as shown in Figure 4 19 96 M5100 USB 3 0 amp USB 2 0 DUPLICATOR 6 amp EOS wy USB Controller B wy Controller Type SMI3255AB 57 v l y Controller Setup Configuration _ enable configuration setup configuration Z LUN 0 RW Removabie O MB LJ WN 1 RW vw Removable w O MB Y Clear CDROM partition Controller Information note if info a aiei then there is nochange Controller Info vendor R ProductName en ill t AM A Serial Number
25. OO MEW AA AAA 29 3 6 Creating and Editing a Job using M51W GUl ooonncnncnnnncccnnccccccncnncnnnnnncnnononanonnnnnnnnanonnnos 31 3 7 Available Operations for a New job in M5100 PR ooonccnnncccncccconcccnnnccnnnnnnonccnnnncnnononancnnons 31 A A o A 31 ate Check arameo Sin rai 33 AS A co 018 AP A Ren Vere ee a Oe ents Vitra ee ae 34 A A Sc Se oe 34 nec AR POC UM VC IN Vtech satura aap aca ttnana A uimeciaan nah aaah aah ie 34 M5100 USB 3 0 amp USB 2 0 DUPLICATOR S720 Greate Master Ple o ln dad lat a edo ella pos 35 A Se EEE LTE ae ee Te TP nee ene eee O 35 9 8 Man Prod Misal ai cid nata 35 STI oMa VEV oe a a iG antGvamened Wane a WM nes Mulmccads 35 310 Sman Prod AM a r E A 35 3 7 11 Smart Create Master File 2 0 0 0 0 ccc cccccccecececcececsceccecececscaucusecscacucesscseaueunenseanans 35 S RS AA E S N EE EAT II 35 LS FIE CODY en a A A acest ead 36 AE O nn bubencaidtaemniuls 36 3 710 File COP a de ee o 36 3 7 16 Create Master File Pattern coco da 36 A O O A A aed etter ess 36 3 7 18 OCT LUN Lorca UA a 36 EAS A A A CN 37 Si 20 TU CON MANO sio isa 37 Selec O A A E E EN 37 3 722 Check Device COnilG ia ii E A A AA E 38 3 8 Operation Modes and Password Editing ccoooooncccnccccccoconnncnnnnnnonononanonnnnnnonononanonnnns 39 3 9 MS100 PR TO01S Men aa bi 40 A PRET ee eC Soe ae Ta eee Ee eee eee eee 40 3 9 2 Greate Master File dados Ses 40 3 93 Checksum Master Device
26. SB Biru aid NeSsveic Slow 3 Place the update USB drive in the M5100 PR master slot Wait for a blinking Green light over the drive and then press START key Using the Up Down keys select the update zip file you wish to execute and press START key Select an update 1 MIS WOO Ris IO Drip 4 The updated files will be copied to the correct locations in the M5100 PR Upon completion the display will read as below Press START or Esc LO RSS SE SS ene 5 Push the START button as instructed You will hear two audible beep tones indicating the M5315 server is shutting down SERVER DOWN 6 The M5100 PR update will be performed and SERVER DOWN displayed on the LCD for a few seconds After the server has started the main menu will be displayed on the LCD and will show the updated software revision M51xx SW Ver 1 01 F SEaWEe Los 2 8 6 Restart Server Select the menu option Restart Server to restart the unit You will be prompted to confirm the restart command software Update gt Restart Server RESTE Selva 2 gt YES START 19 M5100 USB 3 0 amp USB 2 0 DUPLICATOR 2 8 Shut Down The last option in the menu is Shut Down Select Shut Down option and press the START key to shut down the unit Res bee OIV r Slate Downe Shut down are you sure gt YES START NO ESC 20 M5100 USB 3 0 amp USB 2 0 DUPLICATOR 3 Using M5100 PR with M51W GUI The M51W GUI is av
27. SB 2 0 DUPLICATOR Figure 4 17 Serial Generator Icon Click on the Serial Generator icon on the desktop to open the Serial Generator application GUI This GUI lets the user generate the serial numbers for the USB drives either by creating a formula or from a file The user can add edit delete as well as export the serial numbers A snapshot of the GUI is as shown below X y Serial Generator wy o Ry File Run Help Add Edit Delete Serial Export Serial Exit Serial Name Formula Figure 4 18 Serial Generator GUI To add or edit the serial number 1 Click Run button on the menu and select Run GenserialServer 2 Click Add button on the toolbar and the following screen pops up 54 M5100 USB 3 0 amp USB 2 0 DUPLICATOR Au RARR KK lt K lt l New Serial 2 w amp ws Serial Name example Source Formula _ Import From File Formula Type Length Value Enable fixed v IMI Enable year 4 v Enable month v Enable day v Enable hour_24 Y Enable min vw Enable sece vw Enable OK Cancel Figure 4 19 New Serial Generator 3 Enter the name of the Serial Generator file 4 Select the desired source to generate Serial numbers The source can either be a formula or a file 5 Ifthe source is a Formula the formula needs to be specified to generate the serial numbers in the desired pattern The formula can be specified by enabling a field in the New Serial screen and setting its length value whenev
28. SB drives are inserted 2 Ifthe mouse cursor is placed over any inserted recognized USB device an ID drive info screen pops up as shown in Figure 3 12 This is an often used function as the user may wish to make sure the M5100 PR duplicator recognizes the USB devices correctly before starting the copy or any operation E Device Information M5100M y x Slot 1 Vendor Product ID 090C Rev 300000 Serial Number 1009090901014558 Manufacturer SMI Corporation Product Name USB DISK USB Speed High 480 Lun 1 Capacity 3932160 blocks 2013265920 bytes 0x78000000 OK Figure 3 12 ID Drive Information of an inserted USB device 27 M5100 USB 3 0 amp USB 2 0 DUPLICATOR 3 Select the job you wish to run from the list of jobs available in the Job List window For eg To perform a simple copy amp verify from a master device select the MasterCopyVerify mlj job and click on the Green Start button in the Job Run tab 4 Once a job has been started by clicking the Start button the LED s over the DUT s on the duplicator will flash and the completion bar on the GUI and the front panel LCD screen will show the operation being executed and the completion of the job as shown in Figure 3 13 des y USB Duplicator International Microsystems Inc Y eS ES File Connection Admin Tools Help van W Job Start Y FAT Y Smart Size 42 262 MB Op2 S Copy Figure 3 13 Starting the Job 5 On completi
29. Size If this option is enabled it checks if the size of the LUN s of the source Master or First Device equals to the size s of the target devices Otherwise it will check if the number of LUN s on the targets equals the number of LUN s on the source checksize checksize disabled unchecked enable checked Master of master LUN s Size of master LUN s selected of Target LUN s Size of Target LUN s First Device of first device LUN s Size of first device LUN s selected of Target LUN s Size of Target LUN s LUN 0 LUN 0 LUN 1 LUN 1 Master Target of Master LUN s of Target LUN s Size of Master LUN s Size of Target LUN s This operation could be the first operation after the set values operation to check the device configuration and give a fail if the target is not the same number of LUN s and size as the Master Sample operations in a job would be e Set values e Check Device Config e Program Verify 3 8 Operation Modes and Password Editing The M5100 PR has two operation modes Operator and Supervisor When in the Operator mode M5100 PR Jobs can only be executed not created or edited To enter the Supervisor mode select Supervisor Mode in Admin menu and enter default password 123456 The password file is in home imi config gui ini To change the M5100 PR GUI Admin password you must edit this file To edit this file 1 Click once on My Computer
30. ailable as a standard feature with the M5100 PR Professional duplicator model or as an optional upgrade to M5100 Stand alone model The M5100 PR runs on a fully featured Linux operating system In addition to standard Linux programs there are special programs written and used by IMI to operate the unit The two main IMI programs that run on the M5100 PR are the backend M5100 PR Server and the front end M51W GUI The backend M5100 PR Server program runs the IMI USB hardware that operates on the USB devices inserted into the M5100 PR front panel The M51W is the GUI program used to create and edit M5100 PR Jobs that will perform the desired USB drive tasks 3 1 Starting the M51W Graphical User Interface GUI In order to use the M5100 PR with the GUI connect a LCD monitor keyboard and mouse to the unit The USB ports to connect the keyboard amp mouse and the VGA port to connect the monitor are located on the side panel of the M5100 PR As soon as the M5100 PR unit is powered on after connecting the keyboard mouse and LCD monitor the initial desktop screen looks as below a Online Help IMI USB Menu v Figure 3 1 Initial Desktop M5100 PR Screen The USB Menu on the desktop screen shows four options Start Stop Sever Start or Stop the M5100 PR server program OP GUI Start the Operator GUI which is a simplified GUI that lets the operator select a job and execute it GUI Start the main GUI To start the main GUI click on the
31. arameters The check parameters operation lets you set the values of the following USB parameters and check if the target drives have the same values for these parameters Figure 3 21 below shows a snapshot of the Check parameters screen 33 M5100 USB 3 0 amp USB 2 0 DUPLICATOR LO Check Parameters Edy iy Ey ux Check Parameters VID Number PID Number _ Manufacturer Product Name USB Speed Number of Lun _ Device Size sectors _ Type OK Cancel Figure 3 21 Check Parameters Screen VID Number Check the Vendor ID of the USB device PID Number Check the Product ID of the USB device Manufacturer Check the Manufacturer name of the USB device Product Name Check the Product name of the USB device USB Speed Check if the USB devices are Full Speed USB 1 0 High Speed USB 2 0 or Super Speed USB 3 0 Number of LUN Check the number of LUNs Logic Unit Numbers in the USB device Device Size Check if the size of the devices is greater than less than or equal to a specific size Type Check if the USB device is a Read Only Read Write or a CDROM device 3 3 Program Program operation is used to program the USB devices based on the values set in the preceding Set value operation 3 4 Verify Verify operation is used to verify the USB devices based on the values set in the preceding Set value operation 3 5 Program Verify Program Verify operation is used to program and verify the USB devices
32. be powered down from the menu function on the LCD screen Press the DOWN key until the LCD screen displays Shut Down function Press the Green START button twice first to select and then to confirm the shut down operation Please refer to section 2 8 6 for a detailed description of the Shut Down operation Shut Down Method 2 This is the preferred method using the LCD Monitor Exit the M51W GUI Then Click on the Linux Star menu which is located at the lower left corner Then select Shutdown Computer in the Leave tab This will shut down the M5100 PR properly Please refer to Chapter 3 on how to use the M51W GUI Shut Down Method 3 Do not use this method unless method 1 amp 2 cannot be used Shutting down the M5100 PR using the Power Key may damage the M5100 PR file system and cause operational problems Press the Green Power button on the side rear panel of the M5100 PR and hold it until the M5100 PR shuts down Release the Power button as soon as the M5100 PR LCD turns off If you continue to hold the key down you will inadvertently power up the system M5100 USB 3 0 amp USB 2 0 DUPLICATOR 2 3 Quick Summary of M5100 PR Keys and Functions The M5100 PR can be completely operated from its front panel Keypad and LCD screen The front panel has 9 keys and a LCD screen which is a 2 line 24 character display Figure 2 1 shows the close up view of the M5100 PR keypad COPY VERIFY COPY VERIFY J mcrosvstens M5116 O
33. blue button GUI Note Upon boot the M5100 PR Server is already running In case the initial desktop screen does not appear after boot up or is frozen when a display monitor is connected to the machine after it boots up please follow the steps below to recover the desktop screen 21 M5100 USB 3 0 amp USB 2 0 DUPLICATOR 1 Press alt ctr and F1 2 Enter login as root 3 Enter password as 123456 4 Atthe prompt type startx and hit enter Figure 3 2 shows a snapshot of the main GUI that is launched on clicking the blue button EOS s USB Duplicator International Microsystems Inc Y DE File Connection Admin Tools Help Job List J Job Run Jobs directory 3 User Mode Log Viewer home user imi jobs P Name Selected Job Information Description x FileCopyVerify mlj Master Copy Verify_USB3 0 1GB_ mlj s Master_verify mlj Operations Parameters Master_verify30_1GB mlj Op 1 Set Values Datasource Master 3 ee s Start Address Start SmartCopyMaster mlj Op 2 Program Verify End Address End Address Mode Megabyte Address Base Base 10 Decimal SmartCopyVerifyMaster mlj Quick Verify No ie Skip Verify Error No ss SmartCopyMasterFile mlj SmartCopyVerifyMasterFile mlj SmartCreateMasterimage mlj SmartVerifyMaster mlj SmartVerifyMasterFile mlj Constraints SSS All Job Files mlj
34. d part is removed and placed in a pass bin To avoid this situation the M5100 PR allows a flag to be set to force the operator to load a full machine every time Check this box for a Fully Loaded Device check If the box is checked the GUI will make sure all the target slots are occupied If any slot is not occupied a dialogue window will be shown as in Figure 3 41 to ask user whether the user wants to continue Fully Load Check wy ZW Machine is not fully loaded Would you like to execute the job anyways Lv ox LO cancel A A Figure 3 41 Fully Loaded Check Dialogue 43 M5100 USB 3 0 amp USB 2 0 DUPLICATOR 4 M5100 PR Special Features 4 1 Barcode Launch of Jobs The Barcode feature lets the user launch the M5100 PR jobs using a barcode reader In order to enable this feature the user needs to be in Supervisor mode and select the Configuration in the Barcode menu option under Tools menu A dialogue box as shown in Figure 4 1 will be displayed to allow the user to Enable Disable the feature le i Barcode Configuration y Ey 2s Barcode Option e Disable barcode 4 Enable barcode OK Exit Figure 4 1 Barcode Feature To setup the barcode file or modify any existing barcode file select the Editor in the Barcode Menu A dialogue box will be displayed as shown in Figure 4 2 to allow the user to add a new barcode file name and specify the job file or modify existing barcode file The barcod
35. d to read Ladrive read s lot again at the end of function a gles Fixed set the blinking rate for smart copy verify erase to the same rate as binary Added mset usbspeedcheck on off command to check usb speed of target gt master source to binary and smart copy verify Added checking prefix postfix and length of serialnumber to checkparameters command Added user checksum with cre mas shal to database Fixed Progress bar hanged in file C py verify with 0 size files Fixed Display Checksum as Zero when all devices failed in copy verify 6 14 13 Lels Server Removed Test Param license from PRO VERS TON Removed the default volume label in format operation Added to get the revision of the devices Added the test parameter to compare the revision of the device Increased the timeout to 5 sec when getting the serial number from the generator Added arm and usb slot mapping for MB MST ZI MA G45 motherboard Tor M3132 Added arm and usb slot mapping for MB MSI 477 MA G49 motherboard for M3209 Fixed volume label to 32 characters for NTFS Added to support Shal Added display error messages with 99 M5100 USB 3 0 amp USB 2 0 DUPLICATOR front keypad e Added checking for mod rev 3 and rev 2 to update with correct mod fw GUL e Fixed running time and last job time e Added SHA1 checksum limited to 40 hex e Added M5208 GUI e Validated A checksum crc etc copy verify license from PRO VERSION inal
36. e file from a master USB device The user can use the entire master device or a specific part of the master device to create the image file The user will also need to specify the name and location of the master image file 40 M5100 USB 3 0 amp USB 2 0 DUPLICATOR LO Create Master File DNS x Select LUN 0 v Create Binary Image File e Use Entire Master Device __ Use Specific Start and End Addresses Start Address O MS End Address 0 MB _ Create IMI Custom Image using Smart Sizing OK Cancel Figure 3 32 Create Master File After the user specified the filename and location the duplicator will start to create the master image file When the operation is done the following window is displayed with the master file information including the master file size checksum CRC32 MD5 hash amp SHA1 values as shown as Figure 3 19 CNO Information slice 127 0 0 1 y UU Master File Information For Slice 127 0 0 1 Lun 0 Size of Area Summed 104 857 600 100 0 MB CheckSum F9D88DD6 CRC32 9F27A9B8 MD5 Hash 8160401EDE6CBO669B05C1CAF2B9A1F2 SHALI 68FOA63B2283AFO6BAA7DF9576E4AFE32E7BFCO9 Device Size 2 013 265 920 1 9 GB Lok Figure 3 33 Master File Information 3 9 3 Checksum Master Device This menu option enables to create the checksum of the master device The user can calculate the checksum by choosing either of the two options depending on whether the master is a binary image file
37. e filename will be used to launch the job ze x Barcode Editor Ss File _ New i Open Ly Save Al Save As Q Quit Job File Filename Job File Browse Target Quantity __ Scan Operator Name current file home user barcode untitle Figure 4 2 Barcode Editor If the Target Quantity check box is checked user has to specify the target quantity in the text box If the Scan Operator Name check box is checked user will be asked to scan or to enter the operator name when the barcode file is executed When the barcode feature is enabled a dialogue box Figure 4 3 will be displayed to ask for the name of barcode file when the GUI starts As soon as the user enters the file name either using a barcode reader or a keyboard entry the job associated with this file name as set using the barcode editor will be launched in operator mode 44 M5100 USB 3 0 amp USB 2 0 DUPLICATOR ges i Barcode vi O Vs OK Exit Supervisor Figure 4 3 Enter Barcode File If the user wishes to bypass the barcode mode he can click on the Supervisor button and then enter the password to enter the standard GUI 4 2 Module Serial Number Module Serial Number is a licensed feature additional fee available in M5100 PR This feature lets the user assign an external module serial number to the USB device in addition to the original device serial number The module serial is typically used for tracking the de
38. e is no hardware error in the unit Select Information menu and press START button Press the DOWN arrow menu key to see the MAC address Save LoS gt iain IN EE ako ta save Los gt Mach No Error Mach No aio O P the O O A a EPESI ES Y AAN O E z MUNG OOO E So ele AO ONO 2 8 5 Software Update IMI sometimes releases software firmware or system updates for bug fixes and for new or improved features for the duplicators The latest update is available 24 7 at IMI s support website http www imi test com support for registered customers during the warranty period If the warranty has expired update may be purchased Please contact IMI s Sales Department for the detail If the machine fails to work with certain memory cards or drives or with certain settings in a job please try the latest update before contacting IMI s Support Department The procedure for performing the software updates is as below 1 Download the software update from IMI website The update will be contained in a zip file Transfer all the items of the update to a USB drive with at least 1GB free space To perform the update select Software update from the menu and press START key Information gt Software Update 2 After selecting Software update the following message will be displayed on the screen Please insert the USB Drive in Master Slot Then Press Enter 18 M5100 USB 3 0 amp USB 2 0 DUPLICATOR Please insert the U
39. e of each failed slot in the result screen when uses standalone The device in master slot will be failed red led on after the Erase Format amp Quick Format operation Reset the mode key to binary by default when a new operation key is hast LIAS Z 01 8 Fixed Server segfault at reboot When the Server Start Turn on all tae LED TOT second then Cura ORT LED a Add beep sound to Operation keys Copy Verify etc aa l bia e Changed the Binary Erase to Full Erase and format e Changed the Fast Erase to Quick Format Auto select the first lun 61 M5100 USB 3 0 amp USB 2 0 DUPLICATOR 62
40. er Capacity VID PID Message A snapshot of the log viewer is shown in Figure 3 16 29 M5100 USB 3 0 amp USB 2 0 DUPLICATOR Database Log Viewer w wy gg a g o o F og A aN as ni 17 tn aoa a a 24 Jul 2013 Y A A Cant RAR ES a OST 17 25 33 23 3 Jul 2013 17 25 44 hom memesertifober nse verifurn gt 2009090803013993 2013283820 2316 409 ETA 2 at Mesa En sr 4 2009070811022212 2013203820 236 6 eo Op 2 ae Mae a9 5 orn 2013263820 236 4096 ote Op 2 at ese Er a es ONIL 2013203820 236 4096 Eero Op 2173 eis En 00 7 2009070812021138 2013203820 236 406 Eee 2 eigen fu 240 f ee lt gt Figure 3 16 Log Viewer In supervisor mode the user can edit the display fields in the log viewer by clicking on the Edit Display button on the log viewer screen A window will be shown as in Figure 3 17 This window lets the user to enable or disable this feature In addition the user can decide what information needs to be displayed in the log viewer after the job is executed Be Log Display Editor y o oy _ Select jobi Dota Items te Display Select Slot Data Items to Display TERA Start Date Job ID Slot End Date Status Serial Num Job Name Last Mod Date Figure 3 17 Log Display Editor 30 M5100 USB 3 0 amp USB 2 0 DUPLICATOR 3 6 Creating and Editing a Job using M51W GUI To create a new job or edit a job enter the Supervisor mode by clicking the Supervisor Mode in the Admin
41. er applicable The user can pick the field from the drop down menu and also has the option to define a new field A sample formula is shown in Figure 4 19 with the different fields in the formula enabled The different fields available to create the formula can be seen in the Help menu as shown below ReadMe D Y wy ey description cntr 36 year 4 year 2 month day hour 12 hour 24 min sec tstamp_10 tstamp_16 tstamp 36 variable variable variable variable variable fixed 4 fixed 2 fixed 2 fixed 2 fixed 2 fixed 2 fixed 2 fixed 2 fixed 10 fixed 8 fixed 6 fixed text portion padded with spaces Spaces sequential counter base 10 0 9 sequential counter base 16 0 9A F sequential counter base 10 0 9A Z 4 digit year 2 digit year 2 digit month 2 digit day of month 2 digit hour 12 hour format 2 digit hour 24 hour format 2 digit minutes 2 digit seconds timestamp seconds since jan 1 1970 base 10 timestamp seconds since jan 1 1970 base 16 timestamp seconds since jan 1 1970 base 36 Figure 4 20 Formula Fields 55 M5100 USB 3 0 amp USB 2 0 DUPLICATOR 6 Ifthe source is a file select the desired file to import the serial numbers from Please note that the desired serial numbers need to be listed one per line in the file and serial numbers from the file will be consumed upon request from the file The file needs to be a Linux Text File ME New Serial yw Ey es Serial
42. erase operation programs FFFF pattern only on the sectors with data and skips the blank sectors 35 M5100 USB 3 0 amp USB 2 0 DUPLICATOR 3 7 13 File Copy File copy operation copies a specified file to a specified location on the target USB drives The user has the option to choose the target slot to copy the file to By default the file is copied to all target slots 3 14 File Verify File verify operation verifies the target USB drives against the file copied 3 7 15 File Copy Verify File copy verify operation copies a specified file to a specified location on the target USB drives followed by a verify le Required Values Dw w E File Parameters Source home user imi datafiles master imx Browse File Browse Directory Destination Slot All v OK Cancel Figure 3 24 File Copy Verify Screen 3 7 16 Create Master File Pattern This operation lets the user create a smart master file imx file with a specific data pattern 8 digit hex value Mm Create Master File Pattern 2 iv aj OS Create Master File Pattern Parameters Master File Name hhome use r datafile maste r imx Pattern Value ASASASA5 8 digit hex value Figure 3 25 Create Master File Pattern Screen 3 7 17 USB Controller This is a special License feature that locks a USB devices manufactured with specific USB controllers by setting it as Read only CDROM devices etc Please contact IMI if you require this featu
43. gets Equal Source The size of the Target drives must equal the size of the source For example if a Master Device is being used the M5100 PR will determine the size of the device and make sure that all copy devices are exactly equal to this size before starting the operation Targets Sizes Equal All copy devices must be exactly the same size For example if the Source is a small binary image file being copied onto large devices all of the target device sizes will be checked to make sure they are all the same size Sum Hex If this box is checked the user is allowed to set a hex value for the data being programmed into the target devices CkSum The eight digit hex byte checksum of the data source CRC The eight digit 32bit transmission CRC of the data source MD5 The MD5 value of the data source SHA1 The SHA1 value of the data source If the Sum constraint is enabled and the user does not enter the hex value of the checksum CRC MD5 SHA1 the following warning message is displayed ze Warning wy A Checksum value is empty User needs to enter value to check e OK Figure 3 20 Checksum Warning Quick Verify If the option is not checked the default is 100 verification If the box is checked user can specify the percentage of the verification Skip Verify Error If this option is checked the user is allowed to skip verify error The user can set the maximum number of errors he can skip verifying 3 7 2 Check P
44. he following attributes Removable Standard Read Write 200MB capacity The second drive will be Removable Read Only and the capacity of the drive minus 200MB Example 2 USB Drive with a single CD ROM Partition A common use of a USB drive is to emulate a CD ROM This example will show how to create a USB Drive with one CD ROM Partition A test job is created called Test mlj job with the following job commands OP1 USB Controller OP2 Set Values Sets up controller and LUN s Select data for LUNO OP3 Program Verify OP4 USB Controller Load data into LUNO Set LUNO Read Only CD ROM mode 50 M5100 USB 3 0 amp USB 2 0 DUPLICATOR e amp MS1W Job Editor File J New A Open i Save Al Save As Te Exit Current Job New job Description Available Operations Current Job Operations af Selected Operation Details Create Master File se F Parameters Remove All Edit Y Remove Create Master Pattern SMI3255AB 57 Controller Erase UMO Op 1 USB Controller Type RW and Removable Smart Program H Size 0 MB Op 2 Set Values Clear CDROM partition Yes Smart Verify Op 3 Program Verify Smart Program Verify Op 4 USB Controller Smart Create Master File Smart Erase Add File Copy File Verify Insert File Copy Verify Constraints e Set LUN Kiosk Mode Tcl Command Format Device gt e Check Device Config lt __ Fully Loaded Check Lom
45. in the desktop screen Under Common Folders in the left column of the screen click Root Folder You will now be in the root directory 3 Select home folder in the root directory and then select imi select Config 39 M5100 USB 3 0 amp USB 2 0 DUPLICATOR 4 Right click gui ini file and open with Kwrite editor Change the password and save the file 3 9 M5100 PR Tools Menu 3 9 1 Update The update function under Tools menu is used to update the M5100 PR software To perform the update using the GUI copy the software update zip file under home imi directory in the M5100 PR Click Update under Tools menu and select the appropriate update file and click Open A Select Update File 2 i ay ps Look in E homelimi r O E E Ba MA Computer ES bin A al ES contig s laa database E3 exe gui init H log tel tellib E M5116_V105 zip File name M5116_V 105 zip Open Files of type Update File zip y Cancel Figure 3 30 Software Update Once the update is done you will see the following message indicating that the update has been performed Restart the GUI now K e Warning v Xx A Slice 127 0 0 1 Files update successful You need to restart the GUI Figure 3 31 Software Update Successful Message Please contact IMI to obtain the latest software release 3 9 2 Create Master File Create master file menu is used to create a binary or smart master imag
46. ions 3 2 5 Help Menu Access the M5100 PR user manual Help amp User Manual Figure 3 9Help Menu Display the version of M5100 PR Server and GUI software as shown in Figure 3 10 Su UWS W Ne About IMI USB Duplicator yy ix IMI USB Duplicator GUI Version 1 3 Model M5116 M5100M 127 0 0 1 Software 1 14 MWish 1 02 Hostname IP Versions License Copyright 2013 International Microsystems Inc http www imi test com OK Figure 3 10 About Menu 25 M5100 USB 3 0 amp USB 2 0 DUPLICATOR 3 3 M5100 PR Default Jobs The default jobs available on the M5100 PR are explained as below CreateMasterFile Create a binary image file of a master data source The output file name of the master image file should use a bin extension Erase Erase target USB drives by writing FFFF pattern to the entire drive FileCopy Copy from a defined file to target USB drives FileCopyVerify Copy a specifed file to target USB drives and then verify the target drives against the file FileVerify Verify bit for bit the target drives against a file Format Format the target USB drives with the specified file system type MasterCopy Copy the entire master drive to the target drives MasterCopyVerify Copy the entire master drive to the target drives and then verify the target drives against the master drive MasterVerify Verify bit for bit the target drives against the master drive SmartCopy Copy
47. manual references M5116 PR all functions and operations described apply to M5132 PR amp M5208 The M5100 PR is a high speed USB duplicator that can copy verify and erase up to 15 or 31 USB devices at a time It can be operated stand alone as well as using professional M51W GUI software The M5100 PR supports super speed USB 3 0 devices as well as high speed USB 2 0 devices It has copy speeds of up to 3 GB min for USB 3 0 devices and is one of the fastest USB duplicators available today 1 1 Figure 1 1 M5116 PR USB 3 0 Duplicator Key Features VV VV VV VV VV VV WV USB 3 0 and 2 0 Support Professional GUI for enhanced job set up and control Front panel function keys for Copy Verify Format with Erase Binary image sector by sector copying for exact duplication Smart copy which copies only the data for FAT FAT32 NTFS exFAT File Systems Bit by bit verification and automatic checksum display Checksum CRC32 MD5 Hash SHA1 Verification Clean and Format USB drives USB Test Function to check the USB device parameters Support for SD MicroSD CF cards using USB card readers SQL database to store logs Optional Smart Copy Support for Linux File Systems EXT2 EXT3 EXT4 8 HFS Optional Support to Create Read Only CDROM LUNs for USB devices with specific controllers M5100 USB 3 0 amp USB 2 0 DUPLICATOR 1 2 Technical Specifications M5116 PR 9 5 X 11 X 15 5 Dimensions M5132 PR 9 5 X 15 18 5 M5208 9
48. napshot of the USB Controller setting is as shown in Figure 4 11 EOS USB Controller 2 AA Controller Type License Feature Only SMI3255AB 57 v Controller Setup Configuration v enable configuration setup configuration 9 RW _v Removable v 200 MB v LUN 1 RW v Removable v O MB v Clear CDROM partition Controller Information enable Information note if info is blank then there is no change vid pid Serial Number _ enable vid pid enable serial number License Feature Only OK Cancel Figure 4 11 USB Controller Configuration In the second USB Controller operation LUN1 is set to R for Read Only All other settings remain the same as in OP1 as shown in Figure 4 12 49 M5100 USB 3 0 amp USB 2 0 DUPLICATOR ze USB Controller 2 Iw ay pe Controller Type License Feature Only SMI3255AB 57 v Controller Setup Configuration Y enable configuration setup configuration RW y Removable _v 200 MB vV LUN 1 R v Removable v 0 MB v Clear CDROM partition Controller Information enable Information note if info is blank then there is no change vid pid Serial Number _ enable vid pid enable serial number License Feature Only OK Cancel Figure 4 12 USB Controller Configuration After saving and executing the job the target USB Drive will contain two partitions and when inserted into a USB computer port will appear as two Drives One partition will have t
49. odes and the Green LED above the MODE key lights up indicating the mode as BINARY or FAST 4 Press the Green START button to start the copy amp verify operation The data from the master drive will first be copied to the target drives and then the data in the target drives will be verified bit by bit against the master drive 5 The following screens on the LCD show the different steps in the copy amp verify operation in Fast mode and indicate that the copy amp verify is in progress JONS rela 11 2 6 M5100 USB 3 0 amp USB 2 0 DUPLICATOR Checking Job Setup OZ ES COS O Cov COJO Seo ODA 8S 5 MSIE 246 0M 38 Upon completion of the Copy amp Verify job a summary screen with pass and fail results is displayed The summary screen also displays the Master drive checksum which is the simple sum of all bytes in the master drive that have been copied to the target drive In the screen below two cycles have been run with a total of 29 passes and 1 failure In the current cycle 14 passed and 1 failed The Master Checksum is A8500000 MASTER CSUM A amp 8500000 Relay 29 se Ole Oe VERIFY using the M5116 PR Insert the master drive on the master slot and up to 15 target drives on the copy slots labeled 1 15 Press VERIFY key to choose verify function The Green LED above the VERIFY key lights up indicating that the selected function is VERIFY The LCD screen also displays the selected function as shown below
50. og file is over written when the unit is restarted gt server log file saves the results from the jobs run from the previous power cycle gt server _debug log file provides the log of the M5100 PR server code and provides useful information for IMI engineering to debug the M5100 PR software Figure 2 2 below shows the three log files saved on a USB drive and Figure 2 3 shows a snapshot of the server log file P Name Date modified Type Size 5 server 12 28 2012 10 01 AM LOG File 7 KB 5 server 12 28 2012 10 04 AM LOG File 7 KB oD server_debug 12 28 2012 10 04 AM LOG File 2 KB Fig 2 2 Log Files 16 M5100 USB 3 0 amp USB 2 0 DUPLICATOR server WordPad File Edit View Insert Format Help Lah Slo 4 Jstartdate enddate jobname lastdate checksum pass fail totalpass totalfa il gqui kiosk operator hostname jobnumber ponumber 12 28 2012 09 32 08 12 28 2012 09 32 11 Quick Format 12 28 2012 09 32 12 00000000 1 0 1 0 0 0 M5100 0 0 position serialnum capacity vid pid status message standbyicc writespee d readspeed activeminread activemaxread activeaveread activeminwrite ac tivemaxwrite activeavewrite 1 106462120914572 257949696 1500 766 1 Passed 0 0 0 et E ee EA ee Startdate enddate jobname lastdate checksum pass fail totalpass totalfa il gui kiosk operator hostname jobnumber ponumber 12 28 2012 09 32 26 12 28
51. on of the job the PASS FAIL information is updated on the GUI screen In addition the USB slot boxes on the GUI screen will go Green for pass or Red for failure as shown in Figure 3 14 O w USB Duplicator International Microsystems Inc Y 5 Xx File Connection Admin Tools Help IV Job Start YM FAT Y Smart Size 42 262 MB Y Op2 S Copy iv Closing Devices IZ CSUM 2958FD89 Y Safely Removed Y Job End Figure 3 14 Job Completion 28 M5100 USB 3 0 amp USB 2 0 DUPLICATOR 6 When a Job completes with a failed device s the USB slot box in the GUI will turn RED Click on the red icon to obtain more information regarding the error Serial Number 1009090901014558 Error Verify Op 2 Fail Mode Verify Message ErNum 2 Fault Address 2A43000 Data 0x46 Figure 3 15 Error Message 3 5 Log Viewer The M5100 PR stores all the results and log information from the jobs run in a SQL database In order to see the logs go to File menu and select Log viewer The user can chose to see the logs for the last job run all jobs run today or jobs runs within a specified time range The log viewer shows two tables one for the job information and the other for the slot information The job table stores job information including Start date End date Job name Checksum Passes Failed Total Passed Total Failed Job Number PO Number etc The slot table stores slot information including Slot Serial numb
52. only the sectors with data and skip the blank sectors Smart Copy is supported for FAT FAT 32 NTFS exFAT File systems An additional license is available to support Smart Copy for HFS EXT2 EXT3 8 EXT4 file system formats SmartCopyVerify Copy only the sectors with data and skip the blank sectors and then verify the copied data SmartVerify Verify bit for bit the programmed data SmartCreateMasterFile Create a smart master file by analyzing the data source for FAT FAT 32 NTFS HFS EXT2 EXT3 amp EXT4 file systems in order to omit unused areas in the memory and create a smaller master image file Smart Master file works only with Smart_Copy Smart_Copy_verify or Smart_Verify The output file name of the smart master file should use a imx extension TestCopy Copy a test pattern TR3 pattern to the target drives TestCopyVerify Copy a test pattern TR3 to the target drives and then verify the target drives against the test pattern 26 M5100 USB 3 0 amp USB 2 0 DUPLICATOR TestVerify Verify bit for bit the target drives against the test pattern 3 4 Running a job using the M51W GUI 1 Insert the master drive on the master slot and up to 15 target drives on the copy slots labeled 1 15 The USB slot icons on the GUI turn blue as soon as the USB drives are inserted and recognized by the M5100 PR unit as shown in Figure 3 11 Click Slot for Info A 12 13 14 Figure 3 11 M51W screen indicating U
53. re 4 6 Enter Module Serial Number 5 Scan or input the module serial from the label of the flash media before inserting the flash media into the slot If you did not input the module serial before inserting the flash media a Remove the card b Click OK on the error message dialog or press the lt Esc gt keyboard key c Scan the module serial from the flash media d Insert the card into an empty slot 6 After the module serial appears on the GUI s Module Serial Number dialog and on the blue slot icon insert the flash media at any slot JobList J Job Run Job Info Click Slot for Info Job Name Kiosk pgm mlj Checksum M 1 2 3 Job 0 PO 0 120 121 Job Flow EOS Module Serial Nu 2 WwW y x Module Serial Enter Serial Number then Insert Device into Slot m Job Control Cancel 0 0 Last Job Totals PASS 0 CLEAR PASS 0 CLEAR Figure 4 7 Module Serial Number 7 Confirm the scanned module serial If the module serial appears twice on the Module Serial Number dialog or needs to be canceled click Cancel on the dialog or press the lt Esc gt keyboard key Repeat the previous steps to fully load the duplicator tester with the flash media 46 M5100 USB 3 0 amp USB 2 0 DUPLICATOR 9 When the duplicator tester is fully loaded select the job and click the Start button to start the job 10 In case of a d
54. re or need more information regarding it 3 7 18 Set LUN Logical Unit Normally the user doesn t have to use this operation unless the user wants to perform operations on a particular LUN on a USB device having multiple LUN s or to perform smart operations on invalid file system or extended partition 36 M5100 USB 3 0 amp USB 2 0 DUPLICATOR LUN The user can specify a specific LUN of the USB Drive or the whole device for operation Ignore Invalid FS This setup is for smart operations where the user wishes the M5100 PR to ignore an invalid file system If this option box is checked the M5100 PR ignores an invalid file system Gs uy Seun D Y YW amp LUN 0 v _ Ignore Invalid Master FS w OK Cancel Figure 3 26 Set LUN Screen 3 7 19 Kiosk Mode This is a special License feature that lets the user start a copy operation asynchronously as soon as a USB device is inserted into the duplicator Please contact IMI if you require this feature or need more information regarding it 3 7 20 TCL Command This operation lets the user add a TCL command directly instead of choosing from the available Job operations Eo TCL Command 2 A TCL Command W OK Cancel Figure 3 27 TCL Command Screen 3 21 Format Device This operation formats a USB device to a specified file format 37 M5100 USB 3 0 amp USB 2 0 DUPLICATOR EOS Format Device y w W X Format Device FS Type FAT v Si
55. sing the M5100 PR Duplicator Stand AloOne cccsccceesseeeeeneeeeneeeeeneeeeneeeeaes 8 at NOTORA POWEr Ubeda dia 8 22 WOOO PIF OWGSE DOWN aid 8 2 3 Quick Summary of M5100 PR Keys and Functions ccccesesssssssesssesssssssesseeeseeeeees 9 24 CORY ti SiG MS IMS 1 GaP IR occ cdo ial o ds 10 25 COPY VERIFY Using the MST 1G PR A o e me 11 26 VERIFY USING the MSI dida 12 2 7 FORMAT amp ERASE using the M5116 PR ooccccccncccccccnncccnnnccnonononnccnnnnnnnononancnnnnnonononananenoss 13 2 8 Menu Functions on the M5116 PR oocccccnnccnncccncnncccnconconannnnononcnnnnnanonnnnnnnnnonancnnononcanonnas 14 201 RUNJO Oo ri ate sta eons tesa ana as een eae ae eee eae aes 14 202 Media ia aaa aia 15 20 AV odiada 16 264A UNO Malaria 18 23 9 SOWIE Uda Erea a E a E 18 206 RESIT SCI Cl id alicia 19 287 SMU DOW ext saincatasattnatetuniue a ea a a aa ara 20 3 Using M5100 PR with M51W Gul ici das 21 3 1 Starting the M51W Graphical User Interface GUI cccccccoconccnncccconccnncnncancnnnononanennnoos 21 32 MENMEN seat alee i iad Saad a S 23 s2 MUNN TMU A at ad ade heli cle A a 23 3 2 2 COMEN MU he ed etd ta ah ett oh Ola do 24 323 PACA TIM IGNOU ein tiie act A A cee MO eet dal sleet Ales Ad tl cco coed 24 32 24 TOOS Men A A cc Ms naeide 25 32o A O sce eahl eNsital 25 33 IMSTO0 PR Delat JOOS a ed 26 3 4 Running a job using the M51W GUl eee cceeceeeeeeeeeeeeeeeeeeseeaeeeeeesaeaeeeeeesaaaeeeeeeeas 27 39
56. to omit unused areas in the memory and create a smaller master image file Smart Master file works only with Smart_Copy Smart_Copy_verify or Smart_Verify The output file name of the smart master file should use a imx extension Test_Copy Copy a test pattern TR3 pattern to the target drives Test_Copy Verify Copy a test pattern TR3 to the target drives and then verify the target drives against the test pattern Test_Verify Verify bit for bit the target drives against the test pattern 2 8 2 Result The Result menu displays the results of the last job run The result displayed includes the Master Checksum and the number of pass fail 15 M5100 USB 3 0 amp USB 2 0 DUPLICATOR MASTER CSUM OQOQOQQ0000 Pols LS Te O07 OC In case of any failure the Result menu also displays the error message with Slot of the failed device If there are multiple failures press the DOWN arrow to see the error messages for each of the failing device PE A is gt 1 Device Size Error 2 8 3 Save Log The Save Log menu is used to save text log files of the jobs run in a USB drive There are three log files that are generated and saved during this operation gt server log file saves the log of the results from the jobs run on the M5100 PR The results recorded in the log file include job infostart end date amp time of the jobs run job name pass fail information Logs are appended to the file every time a new job is run and the l
57. uplicate module serial used the below error message is prompted to the user asking if it s ok to continue to proceed the job with the duplicate serial s Click ok to run the job or Click cancel to change the duplicate serial E EX jo gt Critical Error Duplicate Serial Number 121 Do you want to continue to proceed OK Cancel Figure 4 8 Module Serial Number Duplicate Error 11 Once the job is complete click on the Log viewer to see the module serial added to the database fields corresponding to the slot If the module serial field is not displayed click on Edit Display button in Supervisor mode to add the Module Serial field to the log viewer display Database Log Viewer Select Slice Slicel_M5100M 127 0 0 1 v Job Filter e Lastjob Run _ All Jobs Run Today _ Jobs Run between 18 Jul 2013 Si and 25 jul 2013 gt Display Option All jobs _ Failed Jc Get Records Export Current Data Delete Data Edit Display Close Form Start Date End Date Job Name Last Mod Date Checksum User Checksum 1 25 jul 2013 15 37 54 25 Jul 2013 15 38 00 home user imi jobs FileCopyVerify mlj 25 Jul 2013 15 37 04 00000000 gt Prema SPRITES Pe PL SP pa sem TS FIOM ERE aah Ne MBAS SAS LSA NSN CAI A RT Te A E A a i A Slot Serial Num Capacity VID PID Message Module Serial 1009090903014036 2013265920 2316 4096 Passed 120 am 1 212 1009070811022192 2013265920 2316 4096 Passed 121
58. vice in the production floor and is usually labeled externally on the USB device When this feature is enabled the user can input the module serial for each USB device under test either by using the keyboard or scan the serial using a barcode reader The inputted module serial for each device will then be added to the SQL database of the duplicator and associated with the slot and the actual device serial Once the Module serial license in purchased and installed on IMI duplicator tester product follow the below steps to use this feature 1 To enable the Module Serial Number feature in IMI duplicator tester go to the Tools menu on the GUI and select ModuleSerial Number Jools Help e Update Create Master File Checksum Master Device Set Operator ModuleSerial Number im Barcode gt Enter job PO Number Figure 4 4 Module Serial Number 2 Click Enable ModuleSerialNumber ze Configure Module Serial v x Module Serial Option e Disable ModuleSerialNumber _ Enable ModuleSerialNumber W OK Cancel Figure 4 5 Enable Module Serial Number 45 M5100 USB 3 0 amp USB 2 0 DUPLICATOR 3 Once the feature is enabled close the GUI and restart the GUI 4 Once you click on any slot icon the module serial dialog appears prompting you to enter the serial of the device je J Module Serial Nu 2 My y Xx Module Serial Enter Serial Number then Insert Device into Slot Cancel Figu
59. ving Multiple Partitions from a USB Drive In order to remove the write protection from a single or multiple Partitions LUN s a simple job with the Operation USB Controller needs to be created In the USB Controller Operation the LUNO must be set to RW and the size to 0 Check Clear CD ROM if the drive contains CD ROM Partitions zo USB Controller a ivy Ey ws Controller Type License Feature Only SMI325 v Controller Setup Configuration v enable configuration setup configuration RW __v Removable_v 0 A 2 Jl Removable _v wt v Clear CDROM partition Controller Information enable Information note if info is blank then there is no change vid pid Serial Number enable vid pid _ enable serial number License Feature Only OK Cancel Figure 4 16 Remove Multiple Partitions 4 4 USB Serial Number Generation The M5100 PR supports generation and writing of unique serial numbers to USB drives manufactured with specific controllers Please check with IMI sales for the list of USB controllers supported by IMI for this feature 4 4 1 Serial Number Generation USB Serial number generation is a special licensed feature and needs to be purchased for an additional fee When this software license is purchased and installed on the M5100 PR a shortcut icon called Serial Generator is created on the desktop A snapshot of this icon is shown in the picture below 53 M5100 USB 3 0 amp U
60. ze KB v _ FAT32 Force if Size gt 32GB __ Force mbr partition table Volume Label Slot All v 8 OK Cancel Figure 3 28 Format Device Screen FS Type Sets the file system type for format Available options are FAT FAT32 NTFS EXT2 EXT3 amp EXT4 Size Sets the LUN size If the value is set to 0 the entire capacity of the drive will be taken FAT32 A FAT32 file format can be forced if the size of the USB Drive is greater than 32GB Force MBR partition table If this option box is checked MBR partition table can be forced Volume Label Sets the Volume Label of the Drive Slot The format operation can be performed for all target slots or only for a single slot 3 7 22 Check Device Config This operation checks the device configuration Either the Master device or the First Device option can be selected to use with the Check device Config operation Che Y Y Y Y Check Device Config e Master First Device _ checksize W OK Cancel Figure 3 29 Check Device Config Screen Master If this option is selected the operation will check the device configuration against the master device configuration First Device If there is no master device this option should be selected to search and use the first device available in the first second or Nth slot for checking configurations The remaining DUT s will then be compared against the First Device 38 M5100 USB 3 0 amp USB 2 0 DUPLICATOR Check

M5100-PR & M5208 USB 3.0 Duplicator User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents

M5100-PR &amp; M5208 USB 3.0 Duplicator User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents

M5100-PR & M5208 USB 3.0 Duplicator User Manual