Installation Manual - Support Technique AURES
Contents
1. Table 10 Output connection overview Figure 20 Inactive relay COM connected to NC Page 18 of 32 XT 1 Installation Manual 13 111 03 2014 RO 012 2014 05 22 3 10 USB The XT 1 has one USB type B connector and acts like a USB 2 0 Full Speed 12 Mbps device This interface is only intended for service and maintenance The interface is connected using a standard cable to a USB port of a PC mt Figure 21 USB connection overview and detail Page 19 of 32 XT 1 Installation Manual 13 111 03 2014 RO 012 2014 05 22 3 11 DIP Switches Two 8 position DIP switches are available for interface and software configuration All switches are OFF by default fon cc T III AI IIA Figure 22 DIP switches S301 left and S101 right 3 11 1 Interface Configuration DIP Switch S301 RS485 2 wire mode S301 1 ON TX connected to RX S301 2 ON TX connected to RX RS485 termination S301 3 ON 120 Q termination between RX and RX Termination should be activated at each end of an RS485 chain RS485 bias S301 4 ON 620 Q pull up from RX to 5 V S301 5 ON 620 Q pull down from RX to 0 V Bias should be activated at one node in an RS485 chain Wiegand Magstripe pull ups S301 6 ON 1 kQ pull up from DO CLK to 5 V S301 7 ON 1 kQ pull up from D1 DATA to 5 V S301 8 ON 1 KQ pull up from CL LOAD to 5 V Pull ups should be activated when the reader is connected to an access control system witho2. Value of Site code E Even parity bit O Odd parity bit X Bit included in parity calculation B Magstripe start character F Magstripe stop character L Magstripe LRC Disabled Wiegand Magstripe output is disabled W265 H10301 26 bit Wiegand 8 bit site code 16 bit data S101 on PooDOoDOODDDDDDDDDDDDDDDDO 1 8 W26N H10301 26 bit Wiegand 24 bit data no site code S101 EN FDDDDDDDDDDDDDDDDDDDDDDDDO 1 8 Page 25 of 32 XT 1 Installation Manual 13 111 03 2014 RO 012 2014 05 22 34 bit Wiegand 32 bit data no site code EDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDO XXXXXXXXXXXXXXXXX W37N H10302 37 bit Wiegand 35 bit data no site code 101 EDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDO XXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXX W37R H10302 37 bit Wiegand 37 bit data no site code no parity 101 DDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDD M8N H10320 8 digit Magstripe 101 25 zeroes BDDDDDDDDFL 165 zeroes Table 15 Wiegand Magstripe formats 4 2 3 3 3 RS232 RS485 The RS232 and RS485 pages makes it possible to set Baud rate and output format for the RS232 and RS485 interfaces It is possible to select a predefined output format or define a custom format All details are described on the Documentation page 4 2 3 3 4 Inputs The reader has three inputs The first two inputs can be used to control the green and red LED from an external access control system to indicate if access has been granted or denied
3. 152600 Accessories Universal Mounting Kit 193600 ISOcard ID tag 225000 WindShield ID tag 221000 Page 31 of 32 Technical Support Phone 46 8 632 19 50 Fax 46 8 750 53 62 E mail support tagmaster com Office Address TagMaster AB Kronborgsgr nd 11 SE 164 46 KISTA SWEDEN Phone 46 8 632 19 50 Fax 46 8 750 53 62 E mail sales tagmaster com Web www tagmaster com
4. 2014 05 22 6 Troubleshooting To facil itate troubleshooting consider the following Make sure that the XT 1 has correct supply voltage and sufficient current Check the small green LED on the right side of the controller board inside the reader When the LED is flashing once per second the reader is powered and the firmware is running If the LED is on but not flashing the reader is powered but the firmware is not running If the LED is off the reader is not powered If using Ethernet communication make sure that the network connection is ok There are small LEDs on the RJ45 socket only visible when the lid of the reader is open A yellow light indicates Link and a flashing yellow light indicates Activity If the IP address has been forgotten or firmware settings have been corrupted the reader can be restored to factory default settings as described in 4 4 Make sure that working and correctly formatted EPC Gen 2 tags are being used 7 Definitions and Abbreviations AES Advanced encryption standard ASCII American standard code for information interchange AWG American wire gauge CR Carriage return DES Data encryption standard DIP Dual in line package EPC Electronic product code FCC Federal communications commission LED Light emitting diode LF Line feed OEM Original equipment manufacturer RFID Radio frequency identification PC Personal computer SecureMarkID A TagMaster implementation for improved
5. Note that by default read blink is disabled when the LED is externally controlled The third input can be used as a read enable disable input This input can be connected to an external presence detector such as an inductive loop to make sure that the reader only reads tags when a vehicle is present All inputs have a debounce filter that is enabled by default When the debounce filter is enabled short pulses on the inputs are ignored Pulses must be at least 20 ms to guarantee that they are detected The polarity of the inputs can be inverted to cope with signals that are active high or active low The read enable disable input can be configured to work in different modes Read time is used to specify how long time reading should be enabled after it has been activated by the input If read time is zero reading is enabled as long as the input is active The Abort after read setting can be used to abort reading after a single tag has been read read time must be non zero for this setting to have any effect The Indicator setting is used to specify the colour of the LED when reading is enabled 4 2 3 4 RF EPC Gen 2 The RF EPC Gen 2 page contains many advanced seitings related to the EPC Gen 2 standard The following settings are the most important Setting Description Carrier Enables or disabled reading of tags Read level Sets the read range in percent Page 26 of 32 XT 1 Installation Manual 13 111 03 2014 RO 012 2014 05 22
6. 012 2014 05 22 5 TAGP Communication Protocol TagMaster Readers can be controlled and monitored using a protocol called TAGP The TAGP protocol is human readable and can be used over TCP IP RS232 and RS485 A terminal emulation program such as PuT TY is all that is required to interact with TAGP The TAGP Protocol Specification 2 can be downloaded from www tagmaster com Use login name partner and password 245ghz PuTTY TagMaster Edition can be downloaded from fip partner 245ghz fip tagmaster com All TAGP messages start with a 4 character message identifier and ends with a new line character To initiate communication with the TAGP server in the reader a client has to send a HELO message specifying the required TAGP version The TAGP server replies with a RPLY message HELOTAGP 2 RPLYHELOOO The client can then send commands to the reader The most important commands are SET SETS GET and GETS SET and GET sets and gets the current value of a variable SETS and GETS sets and gets the stored value of a variable The stored value is used to initialize the variable at startup The following example shows how to set the LED to green SET LED GREEN RPLYSET 00 The reader sends events to the client when something happens The following example shows a TAG event that is sent when a tag has been read EVNTTAG 20140416151015810500507 351413500500500500500 500500 Page 29 of 32 XT 1 Installation Manual 13 111 03 2014 RO 012
7. 03 2014 RO 012 2014 05 22 3 Interfaces 3 1 Cables Connections to the XT 1 is primarily done using the central M20 cable gland Figure 4 Pos 1 and secondarily by replacing any of the 4 pcs of M16 blind plugs with cable glands Figure 4 Pos 2 Shielded cables should be used for all connections Select cables suitable for the installation environment considering indoor or outdoor environment and use flexible cables with stranded wire The reader chassis should be grounded T UZ 3 Figure 4 Cable connections for XT 1 Pos 1 is M20 cable gland Pos 2 is M16 blind plugs Instructions 1 Select and use the M20 cable gland insert corresponding to the number of cables required The cable gland can be used with one cable 6 12 mm or by using the supplied insert with two cables 2 6 mm see Figure 5 2 Open XT 1 lid by loosening the 8 screws on the front and slide the lid open see Figure 6 for reader with lid in open position 3 Feed the cable or two cables through the cable gland and through the chassis All parts of the cable gland except the nut shall be on the outside of the XT 1 4 Connect the wires to relevant terminals and connections depending on interfaces being used If using RJ45 connectors for Ethernet these must be crimped inside the reader 5 Connect the shielding of the power cable to the chassis grounding point using the grounding screw Figure 6 Pos 1 6 Screw the cable gland to tighten and ensur
8. 1 Installation Manual 13 111 03 2014 RO 012 2014 05 22 2 2 Mounting Instruction 2 2 1 General Mount the reader in a horizontal position with the cable glands on the bottom side Direct the reader so that the reading lobe covers the positions of the tags For optimal performance tilt and rotate the reader into a position so that the front side of the reader is parallel with the front side of the tag to be read Align the reader so that the actual reading range is 60 70 of the specified maximum Figure 1 shows a typical reader installation TM00103 Figure 1 Reading lobe The UMK Universal Mounting Kit Part No 193600 see Figure 2 from TagMaster enables the reader to be mounted in a wide variety of positions and angles The kit contains all parts needed for mounting the reader on a wall or on a pole The UMK is designed and suitable for outdoor use See separate data sheet for more details on installation 1 Figure 2 UMK for wall and pole mounting of XT 1 Page 5 of 32 XT 1 Installation Manual 13 111 03 2014 RO 012 2014 05 22 2 2 2 Dimensions 8x M4 Thread 8 mm deep Pressure balance membrane Product Identification Regulations and Standards 11 8 O 300 A lt AN 2 4 61 15903 YOO 0 OS ff Removable blind plugs for cable entry M16x1 5 Figure 3 XT 1 Dimensions Page 6 of 32 XT 1 Installation Manual 13 111
9. Security using EPC tags TAGP A TagMaster protocol for RFID reader communication TCP IP An Internet protocol suite UMK Universal mounting kit USB Universal serial bus XT 1 A TagMaster RFID reader 8 References 1 2 Manual 06 147 UMK 193600 DATA SHEET 05 172 TAGP PROTOCOL SPECIFICATION s and documentation can be downloaded from www tagmaster com Page 30 of 32 XT 1 Installation Manual 13 111 03 2014 RO 012 2014 05 22 9 Technical Specification Operating frequencies XT 1 eu 865 6 867 6 MHz Europe XT 1 us 902 928 MHz US Americas Read range Up to 8 meters 26ft with TagMaster UHF tags with SecureMarkIDO Windshield ID tag and ISO Card ID tag Weight 2 3 kg 5 1 lbs Ingress protection IP 66 Operating temperature 40 C to 60 C 40 F to 140 F EN 60068 2 1 Ad En 60068 2 2 Bd EN 60068 2 14 Nb Output 3 isolated outputs shared with Wiegand Magstripe Relay 1 relay output 6OVDC 2A Interfaces RS232 RS485 Wiegand Magstripe 2 pcs Ethernet and USB service Interface Certificates CE Certificate according to R amp TTE directive 1999 5 EC and FCC ROHS Directive 2002 95 EC and 2011 65 EU WEEE 2002 96 EC Communications protocols TAGP and various OEM protocols Encrypted air interface According to EPC Gen 2 ISO 18000 6C Radio EN 302 208 1 EN 302 208 2 FCC CFR 47 Part 15 subpart C FCC ID M39XTXX Manuals and documentation XT 1 Installation Manual 13 111 TAGP Manual 05 172 Part No XT 1 eu 152500 XT 1 us
10. Wiegand format Tested version Built in No pull ups pull ups 9101 XT 1 DIP Settings Strap at P14 S101 No strap at P14 S101 S301 Table 14 Easy Configuration part 2 of 2 To get all digits from the SecureMarkID tag it is necessary to solder a strap at P14 on the RCO DB 50W board Without this strap it is only possible to get the last four digits from the tag Page 23 of 32 XT 1 Installation Manual 13 111 03 2014 RO 012 2014 05 22 4 2 Web Interface XT 1 has a web interface for configuration and maintenance The web interface is designed and tested to work with Google Chrome 34 Microsoft Internet Explorer 10 and Mozilla Firefox 28 Before it is possible to connect to the web interface the PC s IP address and subnet mask must be changed In Windows 7 this is done using Network and Sharing Center in Control Panel Click on Local Area Connection Properties TCP IPv4 and Properties Select Use the following IP address and fill in IP address 10 0 0 10 and Subnet mask 255 0 0 0 as shown in Figure 25 Click OK Internet Protocol Version 4 TCP IPv4 Properties General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings 5 Obtain an IP address automatically Use the following IP address IP address Subnet mask Default gateway Obtain D
11. oneal aT ag ore aT Se AN cera ear eA eee ENARE 24 4 2 1 E AA LE BA A EA AE ATE ONE 25 4 2 2 Mn ie cereal Nine caren A sind Gr 25 4 2 3 SENOS csi 25 4 2 4 VY CIO A E E 27 4 2 5 Mn O 28 4 2 6 CIO AE A EE E AEE E ae ieee cece 28 4 3 FDW e UI E mer mee mara 28 4 4 Factory Deal conos rios ban ae i oe en el ieee eee ee 28 5 TAGP Communication Protocol 29 6 Troubleshooting 30 7 Definitions and Abbreviations 30 8 References 30 9 Technical Specification 31 Page 3 of 32 XT 1 Installation Manual 13 111 03 2014 RO 012 2014 05 22 1 Introduction 1 1 Overview The XT 1 is an UHF RFID reader compliant with EPC Gen 2 ISO 18000 6C The reader is specifically tailored for Automatic Vehicle Identification AVI applications such as Parking Gated Communities and Condominiums lt has been designed to provide absolutely premium performance for read range and environmental specifications while also giving a large number of interface options and having an innovative implementation for TCP IP connectivity and monitoring 1 2 Tags XT 1 supports any UHF tag compliant with the EPC Gen 2 standard XT 1 also supports the SecureMarkID format developed by TagMaster to ensure that each tag has a truly unique identity that is difficult to duplicate 1 3 Security and SecureMarkID The EPC Gen 2 standard was initially developed for low cost item management and has for that reason no built in support for encryption like DES or AES This differentiates the system
12. EPC channel mask Sets which frequencies that shall be used in EU readers not applicable in US readers EPC memory bank Specifies which parts of the EPC tag to read The default setting EPC SecureMarkID makes it possible to read both EPC tags and secureMarkID tags EPC custom format Used to specify in detail which parts of the EPC tag to read All details are available on the Documentation page Table 16 RF EPC Gen 2 settings 4 2 3 5 Tag Filter The reader has a tag filter that controls how often tags are reported The filter can be set to work in one of the following modes Mode Description Tags are reported every time they are read Tags are reported periodically every Filter timeout milliseconds Once Tags are reported once and have to be away for at least Filter timeout milliseconds before they are reported again Report Similar to once except that a TAGP GONE event is generated when the tag has been away for Filter timeout milliseconds Table 17 Tag filter settings It is possible to activate read beep and read blink to get an indication every time a tag is reported 4 2 3 6 Data Selection The data selection settings make it possible to specify which part of the data from the tag that shall be used and how it shall be interpreted All details are available on the Documentation page 4 2 4 Web Tools 4 2 4 1 Read Tag The Read Tag page makes it easy to read tags and display tag contents y 4 Ta
13. NS server address automatically amp Use the following DNS server addresses Preferred DNS server Alternate DNS server Validate settings upon exit Figure 25 Changing IP address in Windows Connect to the reader by entering the reader s IP address in the web browser s address bar The reader s IP address can be found on a label on the backside of the reader Figure 26 shows the web interface with all menu alternatives expanded Note that the web interface may look slightly different depending on the version of the firmware in the reader Up to date documentation is always available by selecting Documentation in the web interface menu I TagMaster XT 1 C 3 10 10 49 63 atin a e P Jagmaster et 2 AT Information This is the XT 1 Reader web interface Settings Security Documentation Date amp Time Reader documentation is available here E TagMaster Contact Information Wieg Mag Address Kronborgsgr nd 11 S 164 46 KISTA Sweden RS232 Phone 46 8 632 19 50 RS485 Fax 46 8 750 53 62 Inputs E mail sales tagmaster com RF EPC Gen 2 Web www tagmaster com Tag Filter Data Selection Web Tools Read Tag Documentation Reboot 2014 TagMaster Figure 26 Web interface with expanded menu Page 24 of 32 XT 1 Installation Manual 13 111 03 2014 RO 012 2014 05 22 4 2 1 Start The Start page provides TagMaster contact information 4 2 2 Information The Information page provides informatio
14. TagMaster XT 1 Installation Manual 13 111 03 2014 RO 012 2014 05 22 Note This equipment has FCCID M39XTXX It complies with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Caution Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Caution To comply with Council Recommendation 1999 519 EC and FCC regulations this reader must be installed to provide a separation distance of at least 25 cm from all persons and must not be co located or operating in conjunction with any other antenna or transmitter Copyright The copyright and ownership of this document belongs to TagMaster AB The document may be downloaded or copied provided that all copies contain the full information from the complete document All other copying requires a written approval from TagMaster AB Disclaimer While effort has be
15. al M A nN n n aaa Ta sees Xx f l ut Asa AMA PPP O Fisk E arnet Fone eect uriene lev Figure 15 RS485 connection overview and detail The hardware supports 2 wire DIP S301 1 2 ON and 4 wire communication half duplex and full duplex as well as multi drop When using RS485 communication correct termination of the interface should be considered in order to handle transmission line effects The XT 1 has a built in option DIP S301 3 ON of 120 Q termination on the receive side to be used at each end of the RS485 chain and an option DIP S301 4 5 ON of 620 Q bias on the receive side to be used at one node in the RS485 chain The options using DIP switches are detailed in Figure 16 and also described in 3 11 RS485 driver Figure 16 RS485 DIP switch configuration Page 15 of 32 XT 1 Installation Manual 13 111 03 2014 RO 012 2014 05 22 Transmitted data to host See Figure 15 for details Transmitted data to host Connections Signal ground 3 Received data from host Received data from host Recommended Max length 1000 m The cable for the RS485 interface must be a twisted pair cable and Wire size conform to the ElA RS485 standard Max Baud Rate 115 2 kb s default Table 8 RS485 connection overview The default output of the RS485 interface is tag data in ASCII format If SecureMarkID tags from TagMaster are being used recommended the numeric identity is sent out If other EPC tags ar
16. e being used the default output is the EPC data The data is followed by CR LF r n A TAGP connection can be initiated by sending the HELOTAGP message to the reader The TAGP connection is terminated with the QUIT message Page 16 of 32 XT 1 Installation Manual 3 8 Inputs 13 111 03 2014 RO 012 2014 05 22 The XT 1 has 3 software configurable inputs The inputs are opto coupled have 1500 VDC isolation and reverse polarity protection The inputs are activated by a current flow and the input impedance is 1 KQ A schematic view of an input is shown in Figure 18 The software functionality is described in 4 2 3 3 4 Figure 18 Input schematic Input 1 positive terminal Input 1 negative terminal Input 2 positive terminal Input 2 negative terminal Input 2 positive terminal Inout 3 negative terminal Min 3 0 V Max 30 V Min 0 0 V Max 0 2 V 1kQ 10 m 100 m 0 5 mm AWG 20 Page 17 of 32 XT 1 Installation Manual 13 111 03 2014 RO 012 2014 05 22 3 9 Relay The XT 1 has a non latching relay available It is typically connected to the logic controlling a barrier gate or other object when the reader is in stand alone operation hn Figure 19 Relay connections overview and detail COM Common See Figure 19 for details Connections de Normally Open Normally Closed Switch voltage Max 60 VDC 30 VAC Switching capacity Max 60 W 62 5 VA Recommended Max length 10m 100m 0 5 mm AWG 20
17. e proper water and dust sealing As an alternative for grounding a metallic cable gland not included can be used to connect the reader chassis to ground using the power cable shielding Page 7 of 32 XT 1 Installation Manual 13 111 03 2014 RO 012 2014 05 22 Figure 5 The XT 1 M20 cable gland with insert for 2 cables Never remove or use the ventilating membrane Figure 6 Pos 2 on the back of the XT 1 for cable connections Figure 6 XT 1 overview Pos 1 is ground screw connection Pos 2 is ventilating membrane Page 8 of 32 XT 1 Installation Manual 13 111 03 2014 RO 012 2014 05 22 3 2 Wires 3 2 1 Terminal Connections Wire connections with the exception of Ethernet and USB see 3 2 2 are added as single wires to spring cage terminal connectors see Figure 7 These are easy to use terminals for single solid or stranded wires Instructions Strip wire lead approximately 9 mm Push screwdriver down to release spring cage Insert wire into terminal Remove screwdriver to clamp wire Gently pull installed wire to make sure connection is reliable a eS Figure 7 Connection with easy to use spring cage terminal Table 1 Wire connection overview 3 2 2 Ethernet and USB Ethernet is connected using RJ45 connectors To be able to fit this connector given the limited diameter of the M20 cable gland and the hole in the chassis such RJ45 must be crimped to the wires inside the reader This is done with corres
18. ee 4 2 3 3 3 The interface has 1500 VDC isolation and overvoltage protection OO i CON 7 Amg ie a di pA ml e Kd Vd hel nl y SN D mi i HMM AM iy FU El 45 O 4 orn e Figure 14 RS232 connection overview and detail TXD Transmitted data to host See Figure 14 for details Connections RXD Received data from host GND Signal ground 2 10 m Specification according to EIA RS232C Belden 9184 or Belden 9502 are recommended Max Baud Rate 115 2 kb s default Table 7 RS232 connection overview The default output of the RS232 interface is tag data in ASCII format If SecureMarkID tags from TagMaster are being used recommended the numeric identity is sent out If other EPC tags are being used the default output is the EPC data The data is followed by CR LF Ar Yn A TAGP connection can be initiated by sending the HELOTAGP message to the reader The TAGP connection is terminated with the QUIT message Page 14 of 32 XT 1 Installation Manual 13 111 03 2014 RO 012 2014 05 22 3 7 RS485 The RS485 interface is used for host communication and supports ASCII output and TAGP lt generally supports longer transmission distances than RS232 Detailed settings are configured in firmware see 4 2 3 3 3 The interface has 1500 VDC isolation and overvoltage protection OO 4333 gt Se heat os 223223 gt ESeu FEE SABE RAARES 57 phong EA gt i Ai 4 s gt ol EJE En q w w
19. en taken to ensure the accuracy of the information in this document TagMaster AB assumes no responsibility for any errors or omissions or for damages resulting from the use of the information contained herein The information in this document is subject to change without notice Page 2 of 32 XT 1 Installation Manual 13 111 03 2014 RO 012 2014 05 22 Table of Contents 1 Introduction 4 1 A A II ketene 4 1 2 A eas 4 13 Security and SecureMarklD osasuna e dle e Lc uli 4 2 Installation 4 2 Sa ei IASTUCHON SS etnia oirlo 4 2 2 MOUNTING IASTU CIO sra 5 2 2 1 EETA E ae AREE tao leen ir la 5 2 2 2 PIC SIO Sate Geechee A a a ao sn ra ra S 6 3 Interfaces 7 3 1 SI A ee eee 7 3 2 A 9 3 2 1 Terminal GOMMECH GINS a a e e e Et es De EEES 9 3 2 2 Ethemet and US o UeNE 9 3 3 POWEF SUD do laicos 10 34 WIi gand MadsiDO isis ii 11 3 4 1 Wiegand MIMI ito ooo ER 12 3 4 2 Magstipe Tian 12 3 5 A ee ater 13 3 6 PP on ce ies os ac ce a 14 3 7 R AO ed ete cee N nists ree ths os ieee wine eee ees ese ie ooeeeeeeeins 15 3 8 T ene a eee ee ee ee 17 3 9 N 18 A A A A eve Reem 19 SAT DIS WIION Ss ad es ARS fon RAS SER wel 20 3 11 1 Interface Configuration DIP Switch S301 occcconncccccnccccncccccncnocncnoncnnnos 20 3 11 2 Software Configuration DIP Switch S101 ccoconccccccnccccncccccncnocnncnacnnnns 20 312 WIGME ANG SOUMG srik na a e 21 313 IMIChOSD Memory CA e eL COS 21 4 Configuration 22 4 1 Easy GOT OUEAUON o oa 22 4 2 A o
20. from for instance many proximity identification systems To address this TagMaster has developed the SecureMarkID format using an encryption algorithm and non writeable parts of the tag to create a truly unique identity that is difficult to duplicate It is recommend to use SecureMarkID tags only together with XT 1 but also to consider these limitations in any application requiring high security As the development of a cryptographic framework for EPC Gen2 proceeds TagMaster will offer future new products to continue to make the most of available technology in an effort to offer the highest possible security 2 Installation 2 1 Safety Instructions The following safety instruction should be observed during installation normal use and service The installation and service should only be done by qualified personnel Shields of cables should be connected to safety ground The XT 1 must be disconnected from all voltage sources before any installation or service work Capacitors inside the XT 1 can hold their charge even if the equipment has been disconnected from all voltage sources Do not modify any part of the product Repair is to be performed by TagMaster only Where local regulations exist these are to be followed The safety information in this manual is a supplement to local regulations It is the responsibility of the local project manager to make certain that local regulations are Known and followed Page 4 of 32 XT
21. gMaster XT 1 x u LE C 5 10 10 49 63 TagMaster Start Information Read Tag Settings o Security Date amp Time ER UA Interfaces M28 30005708 Ethernet OLN 2002083981501200170F169 Wieg Mag gt RS485 M28 39999411 Inputs RF EPC Gen 2 Tag Filter Data Selection Web Tools Documentation Reboot O 2014 TagMaster Figure 27 Read Tag Page 27 of 32 XT 1 Installation Manual 13 111 03 2014 RO 012 2014 05 22 4 2 5 Documentation The Documentation page provides up to date reader documentation 4 2 6 Reboot The Reboot page makes it easy to reboot the reader e Press the Reboot button to initiate a reboot Reboot Reader Press the button below to reboot the Reader Reboot e Wait for the reboot to complete Rebooting Reader Please wait while the Reader reboots Ps E 4 3 Firmware Upgrade The latest version of the reader firmware can be downloaded from ftp partner 245ghz fip taqmaster com Vigilant Firmware Follow the instructions in the README document that is available in the same directory to install the required tools and upgrade the reader firmware 4 4 Factory Defaults Use the following procedure to restore the reader to factory default settings 1 Set DIP switch S101 2 to ON S101 faPalslalslels 1 8 2 Power cycle the reader 3 Set DIP switch S101 2 back to OFF S101 falsalelellela 1 8 Page 28 of 32 XT 1 Installation Manual 13 111 03 2014 RO
22. n about the system 4 2 3 Settings All configuration of the reader can be done on the Settings pages For all settings it is possible to get help by clicking on the question mark Click the Save Settings button to activate changed settings Click the Factory Defaults button to restore all settings on a page to factory defaults 4 2 3 1 Security The Security page makes it possible to change the TAGP password that is used to authenticate TAGP clients Make sure to set this password if the reader is connected on a public network 4 2 3 2 Date amp Time The reader has a battery backed real time clock that can be set on the Date Time page 4 2 3 3 Interfaces 4 2 3 3 1 Ethernet The Ethernet page shows the current Ethernet settings and makes it possible to set IP address netmask and gateway 4 2 3 3 2 Wieg Mag The Wiegand Magstripe page contains all settings related to Wiegand Magstripe It is possible to select a predefined format or to define a custom format A description of all predefined formats and how to define a custom format is available on the Documentation page The most common predefined formats can also be selected by setting DIP switches S101 6 8 as shown in the table below When any of these switches are in the ON position the reader is also configured to report tags once and only accept SecureMarkID tags see 4 1 for more information D Data from tag bit for Wiegand digit for Magstripe S
23. ponding standard tool and RJ45 Pass the Ethernet cable through the cable gland before crimping the connector on the cable USB is intended for service and maintenance and is therefore connected only when lid is open Connection is done using a standard USB type B cable Page 9 of 32 XT 1 Installation Manual 13 111 03 2014 RO 012 2014 05 22 3 3 Power Supply The XT 1 shall be powered by an isolated power supply suitable for outdoor use The required voltage is 12 VDC to 24 VDC It is recommended to use a power supply of 24 VDC 0 5 A minimum CORRA 9 nection overview and detail m eam Figure 8 Power supply con The power input has built in protection for an accidental connection of reversed polarity High supply potential See Figure 8 for details Subo vveliaas 12 VDC to 24 VDC ppiy 9 Absolute minimum rating 10 VDC absolute maximum rating 30 VDC Recommended Max length 10m 100m Recommended 1 5 mm AWG 16 Table 2 Power connection overview Page 10 of 32 XT 1 Installation Manual 13 111 03 2014 RO 012 2014 05 22 3 4 Wiegand Magstripe The XT 1 has a software configurable Wiegand Magstripe interface The interface has 1500 VDC isolation and overvoltage protection The software functionality is described in 4 2 3 3 2 Using DIP switch S301 6 8 it is possible to activate 1 kQ pull up resistors on DO CLK D1 DATA and CL LOAD Details are shown in Figure 10 The DIP switches are al
24. so described in 3 11 Wiegand 0 See Figure 9 for details Connections Wiegand 1 Wiegand Card load Signal ground 1 Magstripe clock See Figure 9 for details Connections Magstripe data Magstripe Card load Ground 0 5 mm AWG 20 1 5 mm AWG 16 above 10 m of length 30 V Max 500 mA Max 1500 VOC Min Table 3 Wiegand connection overview 5V 1kQ 1kQ 1kQ S301 6 S301 7 301 8 DO CLK D1 DATA CL LOAD Figure 10 Wiegand Magstripe DIP switch configuration Page 11 of 32 XT 1 Installation Manual 13 111 03 2014 RO 012 2014 05 22 3 4 1 Wiegand Timing The following values apply when all outputs are pulled up to 5 V with 1 KQ resistors Symbol Parameter tsu CL to D setup time F Fall time all signals tr Rise time all signals Pulse interval Pulse width CL hold time after last D change Table 4 Wiegand interface timing CL DO D1 Figure 11 Wiegand timing diagram 3 4 2 Magstripe Timing The following values apply when all outputs are pulled up to 5 V with 1 kQ resistors Symbol Parameter tsu LOAD to CLK setup time F Fall time all signals tr Rise time all signals Clock low Clock high LOAD hold time after last CLK change Table 5 Magstripe interface timing LOAD tsu to DATA Figure 12 Magstripe timing diagram Page 12 of 32 XT 1 Installation Manual 13 111 03 2014 RO 012 2014 05 22 3 5 Ethernet The XT 1 has a built in 10 Mbps 100 Mbps Ethernet swi
25. tch and dual ports This makes it possible to connect a number of readers in a system without the need for additional network equipment The two ports A and B are using RJ45 connectors and are fully equivalent f A AA KMA A a e CITI ATA Figure 13 Ethernet connection overview and detail The XT 1 supports auto crossover Auto MDIX so that installation can be done using both patch and crossover cables The connectors have eight pins and the wire scheme is based on the 1568A standard The interfaces have separate isolation of 1500 VDC The default IP address of the device is unique among XT 1 readers and can be found on the label on the back of the XT 1 This makes it possible to create a stand alone network without changing any reader network settings Detailed network settings are configured in firmware see 84 2 3 3 1 Each port has two LED indicators for Link Activity Yellow Flashing Yellow and 10 Mbps 100 Mbps speed Off Green Port A See Figure 13 for details Port B 100 m CAT5e cable or better is required for the Ethernet connection Table 6 Ethernet connection overview Ethernet communication is normally done using TagMaster protocol TAGP available at port 9999 see 2 for details Page 13 of 32 XT 1 Installation Manual 13 111 03 2014 RO 012 2014 05 22 3 6 RS232 The RS232 interface is used for host communication and supports ASCII output and TAGP Detailed settings are configured in firmware s
26. uration 4 1 Easy Configuration XT 1 can be configured to work with common access control systems using DIP switches S101 6 8 When any of these switches are in the ON position the reader is configured to report tags once accept SecureMarkID tags only and use the specified Wiegand Magstripe format Cable Connections with 500RW22 Omnis with EV2 o fev fev ema fev eaw pwe e femea e oo o Doak o DOIOLOCK ficomeB cew omoara omoara comgo oaao E e a Access System Configuration Settings Configure the Configure the XT 1 behaves like a ARX RX WEB Bewator Entro RB500 reader in system to use card system to use Clock amp Data mode type Wiegand H10302 format Configure the Paxton system to use reader type Clock amp Data Tested RX WEB PR300233 Bewator Entro Bewator 2010 version build 8418 version 6 55 011 Omnis 6 0 107 17 2 0 5 Built in 2 2 KQ to 5 V 3 3 KQ to 5 V XT 1 pull ups 1 kO to 3 3 V pull ups required S301 XT 1 DIP Settings Net2 Lite version 4 28 8417 S101 Bewator Entro 2 6 5 101 ON Older versions 101 9301 Table 13 Easy Configuration part 1 of 2 Page 22 of 32 XT 1 Installation Manual 13 111 03 2014 RO 012 2014 05 22 XT 1 RCO R CARD M5 with DB 50W Cable Connections CL LOAD DO CLK DATAO D1 DATA DATA1 DC N C IN1 N C N C N C C IN2 Access System Configuration Settings The RCO system automatically detects the
27. ut built in pull ups Table 11 Interface Configuration DIP Switch S301 3 11 2 Software Configuration DIP Switch S101 Firmware upgrade mode S101 1 is used for firmware upgrade See 84 3 for more information Factory defaults S101 2 is used to restore the reader to factory default settings See 84 4 for more information Easy configuration S101 6 8 are used for easy configuration of Wiegand Magstripe and other settings when using XT 1 with an access control system See 84 1 for more information Table 12 Software Configuration DIP Switch S101 Page 20 of 32 XT 1 Installation Manual 13 111 03 2014 RO 012 2014 05 22 3 12 Light and Sound The XT 1 is equipped with bright LEDs for external signalling see Figure 23 These can indicate red green yellow based on firmware settings A buzzer is also available and the default setting is off Figure 23 LED overview 3 13 MicroSD Memory Card Slot The XT 1 is equipped with a microSD memory card slot for additional storage see Figure 24 Figure 24 microSD overview Page 21 of 32 XT 1 Installation Manual 13 111 03 2014 RO 012 2014 05 22 4 Config
Download Pdf Manuals
Related Search