OT-PLC601 User Manual-NEW
Contents
1. Model OT PLC601 Ethernet Media Converter Use Notes 1 Signal transmission cable must be the copper cable Other material cables will cause the decrease of signal transmission quality and distance 2 Transmitting data network signal by mixing twisted pair telephone line coax cable or Power Line connection is available 3 This device has no waterproof design Please use the product in dry environment 4 Please choose matching power supply specification 12VDC 1A to supply power for devices respectively 5 Please do careful setting before using There is only one Master in a line otherwise it can not transmit network signal 6 Long distance cable connections must be standard connection method such as welding or use connectors 7 If devices fail do not disassemble or repair it by yourself Please contact us timely Product Features Transmit 10 100 BaseT Full Duplex Ethernet up to 1000m over any 2 wire copper cable One Ourten master at the network end can support multiple slaves and connected devices Different terminals to choose such as RJ45 RJ11 BNC Two Pins terminals etc Low power consumption high performance error correction coding technology Built in transient protection Industrial temperature range Easy configuration plug and play The OURTEN model OT PLC601 Ethernet over 2 wire Transceiver is a compact media converter that allows 10 100 BaseT Ethernet to be transmitted using any 2 wire copper cabl2. Camera CAT 5 lt 100m Door Access S Or other IP device OT PLC601 IP Camera CAT 5 lt 100m di Door Access _ BREW Or other IP device OT PLC601 Figure 2 Bus architecture Connection Power Ethernet Transmission via Power line IP Signal IP Power CATS Power Filter Power Filter AC220V AC220V NVR Figure 3 Additional Application Technical Specifications Category Description Available Voltage Range 12VDC Power Standard Compliance IEEE1901 IEEE802 3 Up down agreement CSMA CA Transmission Rate Physical speed 500Mbps Encryption way 128 bit AES Encryption Reliability MTBF gt 30000 hours l 108mmx84mmx24mm ERTSE We eky including the terminal length Product Physical Material Aluminum Characteristic Net weight 300g PC Working Temperature 40C 85C Storage Temperature 55 C 125 C Operating Environment Working Humidity 20 85 Storage Humidity 10 90 Page 5 of 7 Cables Type and Network Data Rate The graph below shows OT PLC601 transmission distance and network data rate The data differs from the cables types When you use this device please choose the suitable cables in line with your demands 100Mbps RG 59 95 94 2 93 4 Y 77 85 3 CAF 3 50Mbps aa 37 30Mbps 0Mbps 50m 200m 500m 800m 1000m The above data for TCP throughput is the measured data in the actual environment The maximum physical layer data is 500
3. Mbps For coaxial cable transmission performance is more stable but it also affected by the cable and terminal matching methods The above tests are all finished in the field test Simple Fault Cases Indicator Feature Phenomenon Power supply works normally POWER OFF No power supply or the power supply does not work normally Line is activated Line is not activated FLASH Line is trying to activation
4. es These devices are often used in legacy installations where existing wire is re used as part of an upgrade to IP devices You can use one master at the network end can support multiple slaves and connected devices These transceivers are extremely simple to use and easy configuration Status LEDs indicate power and link connectivity activity for RJ45 and 2 wire ports This product can be widely used for network extension system network security network information publishing system network renovation and expansion systems railway urban traffic mining and telecommunication etc Terminal Instructions Power Indicator RJ45 Terminal 84mm Power In RJ45 Terminal Power In Two wire Terminal err ai Configuration Instructions OURTEN model OT PLC601 transmits high bandwidth Ethernet signals over 2 wire cables This group typically consists of one OT PLC601 Master located at the control room usually connected to an Ethernet switch or router and up to 4 6pcs remote OT PLC601 Slave which are usually connected to IP cameras or other remote IP devices Step One Gather Devices e OT PLC601 e 12VDC 1A power supply e Two wire cables P camera or other network devices Step Two Connection 1 Connect the LAN Port of Master side to the network equipment RJ45 output Two wire terminal is connected to two wire 2 Connect the low voltage power supply 12VDC to the power port of Slave side Power indicator is on Link i
5. ndicator is on 3 Connect the other end of the two wire cable to the Master two wire terminal the Ethernet Out is connected to the network equipment such as PC through network patch cord 4 Connect the low voltage power supply 12VDC to the power port of Master side Power indicator is on Link indicator is on 5 When network transmission is smooth the devices automatically try to connect The Line indicator quickly blinks Then it shows that network signal transmission is normal Installation Instructions 2 wire Master OT PLC601 OT PLC601 CAT 5 lt 100m IP Camera 1000mM 3280ft PC Switch pray 2 wire Master Slave CAT 5 lt 100m a IP Camera Test OT PLC601 OT PLC601 Figure 1 Typical Installation Most installations that use the OT PLC601 involve the replacement of old analog equipment with new IP devices while reusing the installed wire In generally there are two connections types One is typical connection Figure 1 above And the other is Bus architecture connection Figure 2 Below You can choose the connection type in line with actual environment 1000m 3280ft IP Camera CAT5 lt 100m MA Door Access EE Or other IP device 6 5 OT PLC601 Pe eamere CAT 5 lt 1007 B _ Door Access EG Or other IP device OT PLC601 CAT 5 lt 100m Master 5 PC OT PLC601 Switch IP
Download Pdf Manuals
Related Search