User Manual - Support Technique AURES
Contents
1. Mone Click on this button to read the current iButton reader configuration Head Tail Enable iButton enable Input Method iButton Auto Response Port 000 0000 Get Configure Word i l i i into the configuration utility Set Configure Word Click on this button to write the iButton reader configuration from the utility into the reader RS232 Conf Baud rate and parity of the reader can be displayed and set here RS232 mode only iButton Head Tail Used to check and modify the iButton Head Tail and onMove OnMove settings Used to enable the iButton should always be set Used to enable disable the Head and Tail This area is used to configure the Head Tail and OnMove characters Used to change the reader mode from RS232 to PS 2 modes and back 5 Click on the Get Configure Word to read the current iButton configuration into the reader The reader will beep once if the configuration has been read in correctly If the reading fails you will get a message error 6 Click on the respective radio buttons to check the Prefix Postfix and OnMove settings Head T ail Head T ail Head T ail Track 1 WIS Head Track 1 WIS II Tail Co Track 1 WIS MW Head Track 1 J15 1 Tail Track 1 WIS MW Hed Track 1 1S I Tail C Track 2 Head Track 2 Tail O Track 2 Head Track 2 Tail O Track 2 Head Track 2 Tail Track 3 Head Track 3 Tail O Track 3 Head Track 3 Tail O Track 3 Hea2. 1 0 Response 3 Click OK CID TestAP A IF baud rate or parity has been changed you should re enter this utility For proper operation OK Note This message is displayed every time you choose the Configure command If you have just changed the baud rate or the parity for RS232 interface the Configure command will fail and display an error message In that case you need to exit the utility and re start it with the new baud rate or parity 4 The Configuration Window is displayed Configure Word Setup Serial Configure Word Conbiqure word Track 1 JIS I Enable 1 Trac Get Configure ord U pper Caze Head T ail 2 Enable Track 1 JIS II Head Track 1 JIS Il Tail k k k 3 Enable Track 2 Head Track il ks ET ks cks Spearator Terminator Enable Tacha Head Button Head Button Tail 4 Tracks Sentinel Enable O Button OnMove J Head Tail Enable Set Configure Word Buton Enah Key Code Tracks Error Report Enable Hes Code Track WIS I Request Track Request Information Track3 Request AP Ver 0 87 Lib er 1 0 Tracks Sequence Request Track1 2 3 Serial iButton Auto Response port EEEE 7 Baud Aate 3 S600 Ww Parity Even w Tracks End Sentinel l 8 Close lacks Separator erminator MSA Auto Response port Trac ck 1 WIS I Start Sentinel v 70 Track 2 Start Sentinel ack 3 Start Sentinel CR
3. Update Firmware CID Utility File View PETJE pdate Firmware Is 11 3 Click on the Select button and select the firmware file Note the firmware file has a skx extension Update firmware Firmware F Temps SKH G0 sks Program Warming Start Update Procedure Don t remove power while update is in progress Do not move mouse or press keyboard while code Update i in progressing Status 4 Click on the Start Update Procedure button The update procedure starts Update firmware Firmware G elect File F T empi S KHI 30 skx Program Warming start Update Procedure Don t remove power while update is in progress Do not move mouse or press keyboard while code Update is in progressing Status In Progress WARNING Do not move the mouse or press the keyboard during firmware upgrade Do not exit the program or remove power during the update or the firmware may be corrupted and you will not be able to use the iButton reader anymore AZ 5 The firmware update is finished Click on the Close button Update firmware Firmware e Program Warming Start Update Procedure Don t remove power while update is in progress Do not move mouse or press keyboard while code Update is in progressing Status Complete firmware updated Progress 6 Click on the Disconnect button in the main window 7 To verify the iButton reader works well follow the steps described in Chap
4. Port drop down box select the desired interface mode Configure Word _ Track 1 WS Enable _ Upper Case YesdyTail Track 2 Enable Track 1 WIS I Head Track 1 WIS Il Tail Track 3 Enable Track 2 Head Track 2 Tail Tracks Spearator T erminator Enable Track 3 Head Track 3 Tail Tracks Error Report Enable Button Head Button Tail Tracks Sentinel Enable Button OnMove HeadT ail Enable a e lButton Enable Key Code Hes Code Track JIS Il Request Track Request Track3 Request Tracks Sequence Request Track 2 3 ka MSA Auto Response port ZE Track 2 Start Sentinel Track 3 Start Sentinel Tracks End Sentinel Tracks Separator ER Terminator Hone we 3 Click on the Set Configuration button then click on Close to exit the Configuration settings 4 In the main window click on the Disconnect button 10 Updating the firmware WARNING To update the firmware the iButton reader MUST be set to RS232 mode You can not update the firmware in PS2 mode Updating in PS2 mode will corrupt the firmware 1 Make sure your reader is set to RS232 mode lf you are not sure follow the steps described in the previous chapters to go to the Configuration window and check the iButton Auto Response port setting If it shows Serial the reader is set to RS232 If not change the interface as described in chapter 9 2 Inthe menu click on Device and select
5. User Manual August 2008 Revision 1 0 SKH300 iButton Reader Configuration Utility Copyright 2008 Jan All Rights Reserved Manual Version 1 0 The information contained in this document is subject to change without notice We make no warranty of any kind with regard to this material including but not limited to the implied warranties of merchantability and fitness for a particular purpose We shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing performance or use of this material This document contains proprietary information that is protected by copyright All rights are reserved No part of this document may be photocopied reproduced or translated to another language without the prior written consent of the manufacturer a ee ee et Oe oe es I Table of Contents iButton reader general characteristics ccccccseccceeeceeeeeeeeceeeceueceueeneeeseuesaueeseeeseeesaes 4 iButton reader factory default settings ccceccceececeeeeceeeeceeeeseeeeseeeeseaeeseeeesaeeesaeeeeas 4 Sotware ANSLAN AON eg incencicedaeenGalsGdesteh dieses a 4 Utility Main Window Description cccccccceeecceeeeceeeeeeeeeeeeeeeaeeeseeeessaeeseaeesseeesseeesaeeeeas 4 Checking the firmware VErsiONn ccccseccccssececeeeeeceeeeeceuceeseeeeseeeessaeeessaueessueeesaeeesaaes 5 Reading and changing the iButton reader Configuration ccccseccseeeeeeeee
6. button and then in the main window click on the Disconnect button Checking the iButton output PS 2 RS232 7 1 PS 2 interface You can check the iButton reader output by opening any program or utility that accepts keyboard input such as a text editor or word processing program 7 2 RS232 interface You can check the output of the RS232 interface iButton reader with any terminal program You will have to set the communication parameters to be the same as the iButton reader interface Changing the interface settings RS232 To change the RS232 interface baud rate and or parity settings follow the steps below 1 In the main window click on the Connect button and select the Device SKH300 Serial Interface COM6 Baudrate 9600 and Parity Even 2 Verify that the communication with the reader works correctly by clicking on the Send button The Response window will show the hardware and firmware versions 3 Select the GET CONFIGURE WORD command from the command drop down list and click OK 4 In the RS232 Configuration area change the parameters as desired RS232 Conf Baud Aate 38400 vw Parity a 5 Click on the Set Configure Word button to save the new seitings and click on the Close button to close the configuration window 6 Click on the Disconnect button in the main window 10 9 Changing the iButton reader interface 1 Follow the steps in Chapter 8 item 1 3 2 In the iButton Auto Response
7. d Track 3 Tail Button Head Button Tail C Button Head Button Tail C Button Head Button Tail Button OnMove Button OnMove Button OnMove Input Method Input Method Input Method Key Code O Hex Code Key Code Hex Code Key Code Hex Code head move 7 To change any of the settings click in the input window o A keyboard will appear under the input window which you can use to enter data You can also use a normal keyboard if you have one connected to your system Under input method you can choose Key Code to enter characters directly from the keyboard or Hex Code to enter hexadecimal character codes If you enter hex codes they will be displayed in the input window enclosed in square brackets for example 45 78 A8 Head T ail Co Track 1 WIS WW Head Track 1 WIS 11 Tail Track 2 Head Track 2 Tail gt Track 3 Head Track 3 Tail Button Head Button Tail Button OnMove hput Method Key Code 3 Hex Code WW Ltt CellC JEJE eE 2 WILLE LL SJ AIS CLC OWCICK LJ CIC EJES FEA E C Ea 8 To save your new settings into the reader click on the Set Configure button The reader will beep if the settings were written to it successfully If the settings can not be written you will get an error message after a few seconds Get Configure Word Set Configure Word 9 Close the Configuration window by clicking on Close
8. der s configuration parameters because it allows you to check that the communication with the reader is working correctly 1 Start the utility 2 Click on the connect button O File View Device Help Issue Comma Command i Options Connect Arguments 3 Select the iButton reader parameters as shown below and click on the OK button If your device is configured with a serial If your device is configured with a PS 2 interface default interface Connect to Ed Connect to Device SKH300 Senall Device EUS SEI eee Interface MET S3 Interlace Baudrate 9600 B audrate TIP If your iButton reader is in serial mode and you access the reader in PS 2 mode you can still check the firmware version and the configuration of the reader This is useful if you can not 5 remember the baud rate and parity settings of your device 4 Select the GET VERSION command in the command window Click on the Send button The firmware version is displayed in the Response window Note if you get an error message at this point it means either the iButton reader module is not installed correctly on the system or in the case of RS232 interface the wrong COM port or communication parameters CID Utility File View Device Help Issue Commands Command GET VERSION Response Set version information hardware version 1 4 software version 1 30 3 Options Arguments Disconnect Suto clea
9. eeeaeeeseeens 7 Checking the iButton output PS 2 RS232 2 cccsececcseeeeceseeeeeeeeeseeeeeseeeeeseneeess 10 Changing the interface settings RS232 0 cccceccccceeeeeceeeeseeeeeseeeeesseeeeseaeeeseeeeeas 10 Changing the iButton reader interface cccccccccsecceceeceeseeeeeeeeeseeeeeseeeeeseeeeeaeeeeas 11 Upaan rhe TNWA E israe ni ee AEREOS EKN AEE REREN 11 1 iButton reader general characteristics The iButton reader supports both RS232 and PS 2 interfaces The iButton reader currently has no support for international keyboard layouts firmware revision v1 30 and earlier A US keyboard layout is assumed iButton reader factory default settings Interface RS232 Baud Rate 9600 Data bits 8 Parity even Stop bits 1 Software installation Connect the iButton reader to the POS system Start the POS system Double click on the CIDTestApSetup file icon and follow the on screen instructions to install the utility on your system Note The reader is not a plug and play device Always connect the iButton reader to the POS system first and then only power up the system to ensure that the device is detected by the POS system correctly Utility Main Window Description This configuration utility was designed for several different devices including magnetic card reader and iButton reader However only the part relevant to the configuration of the iButton reader will be described here s CID Utility File View Device H
10. elp Issue Commands Command 3 w Response 1 Options Connect Arguments Cl Auto clear previous response Clear Place new response on top 0 Information Manual Input Response Status T Data Disconnected Library version Application version RTSICTS Add checksum at tail of data Auto clear previous response Clear Place new response on top Options ICTS Check Baudrate Data Bits Parity stop Bit Device Status Miscellaneous Show Response received alert Show Response received message in response boxs Disconnected Click on this button to select the device and interface parameters and Connect to establish the connection between the reader and the utility Click on this button to release the connection between the utility and Disconnect ni l l the reader This is the last action before closing the program Select the reader command from the drop down box Command sane Used to access the iButton reader configuration window Response Shows the reader response to a command Auto clear previous response I O Pace nonresponse Display options for the Response window on top Clear button Button to clear the response window Information area Shows program version information Note the other items in this window are not used for the iButton reader Checking the firmware version This command should always be executed first before attempting to modify any of the rea
11. r previous response Clear Place new response on top Information Manual Input Response Status Data Connected Library version 1 0 Application version 0 51 RTSICTS Add checksum at tail of data Auto clear previous response a Paene e Options ETS check Baudrate 9600 v Data Bits a v Parity uae Device Status Miscellaneous Ready Clear how Response received message in response u 5 Show Response received alert Mee Connection established 6 Reading and changing the iButton reader configuration 1 Follow the steps in Chapter 5 2 Choose the GET CONFIGURE WORD or the SET CONFIGURE WORD command from the command window Both commands are equivalent Note Only the first three commands in the list are used for the iButton All the other commands are for other devices CID Utility File View Device Help Issue Commands Command GET VERSION GET VERSION N Get version information eee ET CONFIGURE WORD software version 1 30 SRD LOAD STA GET SYSTEM STATUS CARD FEED CONTROL ICC SELECTION ICC ACTIVATION ICC DEACTIVATION Response Options Arguments Disconnect ICC ASYNC APDU EXCHANGE C Auto clear previous response MSC AUTO READ CONTROL a MSC WRITE Place new response on top CARD CAPTURE Information Manual Input CARD DROP EJECT Status Data CARD DISPENSE SET MODE Connected SET BAUD ICC SLE4 428 IO Library version ICC SLE4442 IO
12. ter 5 to display the firmware version Response Set version information hardware version 1 4 software version 1 30 D uto clear previous response Clear Place new response on top 13
Download Pdf Manuals
Related Search