Fan Retrofit Kit FANKIT01-10 - Installation Manual
Contents
1. 15 Close the inverter see inverter installation manual 7 2 Disposing of the Fan Retrofit Kit Dispose of the fan retrofit kit in accordance with the applicable disposal regulations for electronic waste 20 FANKITO 1 lA en 12 Installation Manual SMA Solar Technology AG 8 Technical Data 8 1 Fan General data 8 Technical Data Width x height x depth 60 mm x 60 mm x 25 4 mm Noise emission typical lt 29 dB A Maximum operating altitude 3 000 m Volumetric flow rate gt 40 m h Electrical parameters Input voltage OV 15V Nominal DC current lt 02 8 2 Multi Function Relay Connection Maximum switching voltage AC 240 V DC 30V Maximum switching current AC 1 0A DC 1 0A Climatic conditions Temperature range 25 60 C Installation Manual FANKITO1 lA en 12 21 9 Contact 9 Contact SMA Solar Technology AG If you have technical problems concerning our products contact the SMA Service line We require the following information in order to provide you with the necessary assistance Device type of the fan retrofit kit e Device type and serial number of the inverter Detailed description of the problem SMA Solar Technology AG Sonnenallee 1 34266 Niestetal Germany www SMA de SMA Service Line Inverters 49 561 9522 1499 Communication 49 561 9522 2499 Fax 49 561 9522 4699 E Mail Servicelin2. Press the locking levers of the left hand socket on the display outwards and remove the ribbon cable plug 5 Loosen the screw on the display and flip the display up until it clicks into place 6 Release and remove the fan plug 18 FANKITO 1 lA en 12 Installation Manual SMA Solar Technology AG 7 Disassembling 7 If the terminals are assigned remove the connection cable from the inverter Flip up the terminals and pull out the insulated wires Hint Note down the order of the connected insulated wires to make it easier to reconnect them Remove the connection cable from the inverter through the cable gland Unscrew the swivel nut to do so Insert the sealing plug in the right hand cable gland and screw the swivel nut hand tight onto the cable gland see Section 6 Connecting the Fan Retrofit Kit page 15 8 Loosen the cable gland of the fan cable To do this loosen the inner counter nut 9 Remove the fan cable with the cable gland and nut from the inverter 10 Loosen the screw on the controller assembly using an Allen key AF 3 11 Remove the controller assembly from the inverter Installation Manual FANKITO 1 IA en 12 19 7 Disassembling SMA Solar Technology AG 12 Place the filler plug in the left hand enclosure opening 13 Fold down the display and fasten the screw hand tight 14 Push both locking tabs of the fan enclosure to the fan and remove the fan with fan enclosure
3. com au SMA Benelux bvba sprl www SMA Benelux com SMA Beijing Commercial Company Ltd www SMA China com cn SMA Central 8 Eastern Europe s r o www SMA Czech com SMA France S A S www SMA France com SMA Hellas AE www SMA Hellas com SMA Ib rica Tecnolog a Solar S L U www SMA Iberica com SMA Solar India Pvt Ltd www SMA India com SMA Italia S r l www SMA ltalia com SMA Japan K K www SMA Japan com SMA Technology Korea Co Ltd www SMA Korea com SMA Middle East LLC www SMA Me com SMA Portugal Niestetal Services Unipessoal Lda www SMA Portugal com SMA Solar Thailand Co Ltd www SMA Thailand com SMA Solar UK Ltd www SMA UK com
4. fan plug in the fan connection of the controller assembly If the multi function relay is to be used on the controller assembly connect the multifunction relay via the righthand cable gland Remove the sealing plug from the righthand cable gland For that unscrew the swivel nut i Storing the sealing plug Store the sealing plug in a safe place The sealing plug is needed again if the fan retrofit kit is removed Insert the connection cable through the righthand cable gland into the inverter In doing so fasten the swivel nut only hand tight on the cable gland Ensure that the connection cable is securely positioned FANKITO 1 lA en 12 Installation Manual SMA Solar Technology AG 6 Connecting the Fan Retrofit Kit Flip up the terminals and insert the insulated wires 14 Fold down the display and fasten the screw hand tight 15 Insert the ribbon cable in the left hand socket on the display until it clicks into place 16 Close the inverter see inverter installation manual Installation Manual FANKITO 1 IA en 12 17 7 Disassembling SMA Solar Technology AG 7 Disassembling 7 1 Disassembling the Fan Retrofit Kit 1 Disconnect the inverter from voltage sources and open it see inverter installation manual 2 If the multifunction relay is assigned disconnect the supply voltage to the multifunction relay and ensure that the device cannot be reconnected 3 Wait for the fan to stop rotating
5. Accessories for SMA Inverters Fan Retrofit Kit FANKITO1 10 Installation Manual FANKITO1 lA en 12 IMEN FANK TL21 Version 1 2 SMA Solar Technology AG Table of Contents Table of Contents Information on this Document 5 2 Safe aia adds 7 Dalle mn Ed ERE PIOS PERSA 7 2 2 Qualifications of Skilled 7 2 3 Batey PEU cs S venit mes Inc 8 3 Scone of Delivery x isa A i eb 9 Product Description 10 4 1 a AAA 66 10 AZ Comtrollerossembie erre aser ri 11 5 Installation 00 12 5 1 Installation Area Overview oia oi RR ER 12 5 2 Removing the Multifunction 12 5 3 Installing the Fan Retrofit Kit in the 14 6 Connecting the Fan Retrofit 15 55 18 7 1 Disassembling the Fan Retrofit 18 7 2 Disposing of the Fan Retrofit 20 8 Technical Data sa AS 21 Bal Fani O O 21 8 2 Multi function Relay Connection 21 A rx ee Red QU ORE wea SE 22 Installation Manual FANKITO1 lA en 12 3 Table of Contents SMA Solar Technology AG 4 FANKITO1 lA en 12 Installation Manual SMA Solar Technology AG Information on this Document 1 Information on this
6. Document Validity This manual is valid for the fan retrofit kit of type FANKITO 1 10 Target Group This document is for skilled persons Only qualified personnel with the appropriate skills are allowed to perform the tasks described in this manual see Section 2 2 Qualifications of Skilled Persons page 7 Additional Information For further information see www SMA Solar com Document title Document type SUNNY BOY 2500TL Single Tracker Installation manual SUNNY BOY 3000TL Single Tracker SUNNY BOY 3000TL 3600TL 4000TL 5000TL Installation manual Multi Function Relay and OptiTrac Global Peak Technical description Symbols Symbol Explanation DANGER Indicates a hazardous situation which if not avoided will result in death or serious injury A WARNING Indicates a hazardous situation which if not avoided could result in death or serious injury A CAUTION Indicates a hazardous situation which if not avoided could result in minor or moderate injury NOTICE Indicates a situation which if not avoided can result in property damage Information that is important for a specific topic or objective but is not safety relevant Indicates a requirement for meeting a specific goal Desired result xiao p A problem that might occur Installation Manual FANKITO1 lA en 12 5 1 Information on this Document SMA Solar Technology AG Typographies Ty
7. e8SMA de 22 FANKITO 1 A en 12 Installation Manual SMA Solar Technology AG Legal Restrictions Legal Restrictions The information contained in this document is the property of SMA Solar Technology AG Publishing its content either partially or in full requires the written permission of SMA Solar Technology AG Any internal company copying of the document for the purposes of evaluating the product or its correct implementation is allowed and does not require permission SMA Factory Warranty The current warranty conditions come enclosed with your device These are also available online at www SMA Solar com and can be downloaded and are available on paper from the usual sales channels if required Trademarks All trademarks are recognized even if these are not marked separately Missing designations do not mean that a product or brand is not a registered trademark The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG Inc and any use of such marks by SMA Solar Technology AG is under licence QR Code is a registered trademark of DENSO WAVE INCORPORATED SMA Solar Technology AG Sonnenallee 1 34266 Niestetal Germany Tel 49 561 9522 0 Fax 49 561 9522 100 www SMA de E Mail info SMA de O 2004 to 2012 SMA Solar Technology AG All rights reserved Installation Manual FANKITO1 lA en 12 23 SMA Solar Technology SMA Solar Technology AG www SMA de SMA Australia Pty Ltd www SMA Australia
8. fan enclosure in the enclosure opening The left hand locking tabs lock into place FANKITO1 lA en 12 Installation Manual SMA Solar Technology AG 6 Connecting the Fan Retrofit Kit 6 Connecting the Fan Retrofit Kit 1 Remove the filler plug from the right hand enclosure opening i Storing the filler plug Store the filler plug in a safe place The filler plug is needed again if the fan retrofit kit is removed see Section 7 1 Disassembling the Fan Retrofit Kit page 18 2 Unscrew the cable gland from the left hand enclosure opening To do this loosen the inner counter nut 3 Insert the cable gland in the right hand enclosure opening and fasten it along with the counter nut from inside 4 Afterthe swivel nut with sealing plug is unscrewed screw the swivel nut with sealing plug on the cable gland 5 Fasten the swivel nut hand tight 6 Unscrew the counter nut from the provided cable gland of the fan cable Insert the fan cable through the lefthand enclosure opening into the inverter from outside Installation Manual FANKITO 1 IA en 12 15 6 Connecting the Fan Retrofit Kit SMA Solar Technology AG Insert the cable gland of the fan cable in the enclosure opening and fasten it to the inside of the enclosure using the counter nut After the swivel nut is unscrewed screw the swivel nut on the cable gland Fasten the swivel nut hand tight Ensure that the fan cable is securely attached Insert the
9. ifications of Skilled Persons The work described in this document must only be performed by skilled persons Skilled persons must have the following qualifications Knowledge of how an inverter works and is operated Training in how to deal with the dangers and risks associated with installing and using electrical devices and plants e Training in the installation and commissioning of electrical devices and plants Knowledge of all applicable standards and directives Knowledge of and adherence to this document and all safety precautions Installation Manual FANKITO1 lA en 12 7 2 Safety SMA Solar Technology AG 2 3 Safety Precautions Electric Shock High voltages that can cause fatal electric shocks are present in the live components of the inverter Prior to performing any work on the inverter disconnect the inverter from any voltage sources see inverter installation manual Electrostatic Discharge By touching electronic components you can damage or even destroy the inverter through electrostatic discharge Earth yourself before touching any components 8 FANKITO1 lA en 12 Installation Manual SMA Solar Technology AG 3 Scope of Delivery 3 Scope of Delivery Check the scope of delivery for completeness and any externally visible damage Contact your specialist dealer if the scope of delivery is incomplete or damaged A Figure 1 Components included in scope of delivery Item Quantity Descripti
10. on A 1 Fan with fan enclosure and cable gland B 1 Controller assembly C 1 Installation manual Installation Manual FANKITO1 lA en 12 9 4 Product Description SMA Solar Technology AG 4 Product Description 4 1 Fan Retrofit Kit The fan retrofit kit consists of a fan and a controller assembly for the fan The fan provides the inverters with additional cooling during high ambient temperatures The controller assembly controls the fan Figure 2 Structure of the fan retrofit kit ltem Description A Fan with fan enclosure Cable gland with nut Plug Fan connection Multi function relay terminals Controller assembly O miolo w Screw 10 FANKITO 1 IA en 12 Installation Manual SMA Solar Technology AG 4 Product Description 4 2 Controller Assembly The controller assembly controls the fan A multifunction relay is placed on the controller assembly The multifunction relay is for switching on and off a fault indicator or another external load based on parameters and measured values of the inverter for further information regarding the use of the multifunction relay see the Technical Description Multi Function Relay and OptiTrac Global Peak and installation manual of the inverter available at www SMA Solar com Symbol on Product Symbol Designation Explanation Warning regarding The product operates at high voltages All work may dangerous voltage only be perf
11. ormed by skilled persons in accordance with this manual Installation Manual FANKITO1 lA en 12 11 5 Installation SMA Solar Technology AG 5 Installation 5 1 Installation Area Overview AA Figure 3 Installation area in the inverter with the lower enclosure lid open and display flipped up ltem Description A Cable routes B Enclosure openings for the connection of the fan retrofit kit C Installation location for the controller assembly D Enclosure opening for the fan along with the fan enclosure 5 2 Removing the Multi Function Relay If a multi function relay is pre installed the installation area of the controller assembly is blocked Before installing the fan retrofit kit the multi function relay must be removed according to the following procedure 1 Disconnect the inverter from voltage sources and open it see inverter installation manual 2 If the multifunction relay is assigned disconnect the supply voltage to the multifunction relay and ensure that the device cannot be reconnected 12 FANKITO 1 lA en 12 Installation Manual SMA Solar Technology AG 5 Installation 3 Press the locking levers of the left hand socket on the display outwards and remove the ribbon cable plug 4 Loosen the screw on the display and flip the display up until it clicks into place 5 If the terminals are assigned remove the connection cable from the inverter Flip u
12. p the terminals and pull out the insulated wire Hint Note down the order of the connected insulated wires The connection to the multifunction relay on the controller assembly will be easier this way Remove the connection cable from the inverter through the cable gland To do this slightly loosen the swivel nut 6 Loosen the screw on the pre installed multi function relay using an Allen key AF 3 7 Remove the multifunction relay from the inverter Installation Manual FANKITO 1 IA en 12 13 5 Installation SMA Solar Technology AG 5 3 Installing the Fan Retrofit Kit in the Inverter Requirements O O The inverter must be disconnected from the power supply and the lower enclosure lid must be opened see inverter installation manual The multifunction relay must be removed and the display flipped up see Section 5 2 Removing the Multifunction Relay page 12 Place the controller assembly in the inverter and push the ribbon cable upwards behind the display The key of the controller assembly must fit into the cutout of the display retainer Fasten the screw of the controller assembly with an Allen key AF 3 Remove the cover of the enclosure opening for fan enclosures Insert the fan with fan enclosure in the enclosure opening The arrow on the fan enclosure must face the display Route the locking tabs on the right hand side of the fan enclosure underneath the enclosure wall and press the fan with
13. pography Usage Example light Display messages e inverter switches to 8 Balanced mode e Connections Slots bold e Elements to be selected Set the Fan Test parameter to 1 e Elements to be entered 6 FANKITO 1 lA en 12 Installation Manual SMA Solar Technology AG 2 Safety 2 Safety 2 1 Intended Use The fan retrofit kit consists of a fan and a controller assembly for the fan The fan provides the inverters with additional cooling during high ambient temperatures The controller assembly controls the fan The fan retrofit kit may only be used with the following inverters SB 2500TLST 21 SB 3000TLST 21 SB 3000TL 21 SB 3600TL 21 B 4000TL 21 SB 5000TL 21 e WB 3000TL 21 e WB 3600TL 21 e WB 4000TL21 e WB 5000TL21 Alternative uses not expressly recommended by SMA Solar Technology AG are not permitted For safety reasons it is not permitted to modify the product or install components that are not explicitly recommended or distributed by SMA Solar Technology AG for this product The enclosed documentation is an integral part of this product Read and observe the documentation Keep the documentation in a convenient place for future reference Only use the fan retrofit kit in accordance with the specifications provided in the enclosed documentation Any other use may result in personal injury or property damage Also observe the relevant inverter manual 2 2 Qual
Download Pdf Manuals
Related Search