FORD Focus, Edge Fusion interface installation manual V100710
Contents
1. NONE if he does not want the icons to pop out when people control it In this case the user may also touch the left top corner power icon to tuner off the monitor and he may also use the left button corner SRC icon to switch the input TheH POS V POS items mean the image location on monitor different video players like DVDs may send out video with different amplitude different image location although it is PAL or NTSC These 2 options will give the installer the convenience of adjusting image perfectly centered in a couple of seconds The input box has separate memory space to remember the IR code of every input RGB input AV1 DVD AV2 Tuner or iPod 1 When the current input channel s IR output is set to PROG the input box goes into IR learn mode when the DIP6 is pulled down to ON state 2 Then one icon will be blinking saying that one IR key press is needed the installer need to point the remote controller toward the whole on RGB input 3 When one code is learned another icon will be blinking saying that another IR code is needed The installer then repeating step 2 until all codes are programmed Then the icons disappear automatically and the installer may start normal operation the touch screen will not acknowledge touch screen operations when it is in programming mode except the SRC key which will terminate the learning progress When the DIP6 is pulled down to ON2. 5 times repeatedly the monitor goes into touch screen calibration mode a cross will be shown on screen and the installer need to use something like a pencil to hit the cross the cross will be changed to another location is one point is recorded This multi point calibration should be done at least once by the installer guarantee precise icon operation to the user and remove piece to piece resistance difference between panels in different cars The input box can output the IR code in a 4 byte protocol which most of AV devices use today the output can be 2 ways 1 wire connect way without carrier frequency or 2 wireless way with carrier frequency The difference is the wireless way says the signal 1 with 38K frequency pulses while the wire way says by just voltage See picture below PCB he may just use the socket of the interface picture here gt and use 2 mechanical relays FOgP Z a www fosp cn Protocol 1001 101010 0110100171 10100001101000 LSB MSBLSB MSBILSB MSBLSB HSB Hi Ims id Erm sit A ddress _ Addre ss ri C ommand Command The input box has 2 IR output pins IR RGB the 6 pin of RGB input and IR_DVD the 7 pin of RGB input The IR_RGB is always in wire connect way without carrier while the IR DVD pin can be wire connect When Dip7 is high in OFF state or in a wireless way When Dip7 is low in ON state in this case the transm
3. Sync should be NTSC composite with negative polarity FOgP Z 3 www fosp cn 3 RGB resolution NTSC RGB navigation that is 320X240 400X240 480X240 Pere hate connexes econ 4 Av1 Av2 cam video 0 7Vpp with 75 ohm impedance M 5 IR RGB IR_AV1 output 3 3V digital infrared control code with 4 data bytes P RRR Aea Reverse trigger threshold gt 5V trigger Ctrl port Pin1 2 and Pin7 2A Tested to have no damage when short circuit to GND for 2 Ctrl port Pin1 2 and Pin7 Relay pull voltage for Audio and touch screen selection Output voltage 5V volts 7 10 Current minutes Leave it open when do not use 11 FO gP 4 g www fosp cn Appendix Original touch panel for extra devices IR output operations When the touch daughter PCB is connected touch control for extra DVD IR may be activated The user does not need the remote controller any more The Ford screen already has a very nice touch screen on top of the LCD This touch daughter PCB has a touch in marked with PNL and touch out connectors marked with CAR both are 4pin Both in amp out connectors have two types of socket SMD and DIP Mechanical relay is used inside to make sure PNL CAR short circuit for original applications The PNL socket should be connected to original touch panel plug with the accessory socket The CAR socket should be connected to original touch panel socket with the accessory ribbon wire Then the touch panel is
4. FOgP 4 te www fosp cn FORD Focus Edge Fusion interface installation manual 100710 This interface can insert RGB navigation 2AV Camera signal onto Ford Focus Edge Fusion and other ford screen Features of this interface v Itis compatible with all Ford 4Pin LVDS CD screen systems which are available in Focus gt Edge Fusion and more they have separate CD unit and screens Y 64Mega dynamical memory is used inside for 2 dimensional spatial zoom and guarantee stable video signal to screen no matter what the input video source the installer use PAL NTSC No signal v Plug and play installation without hurting the original circuit and warranty label Special PPS shell makes this interface stable against noise Low EMI and very reliable the black plastic shell is actually conductive v Optional Touch operation to installed DVD TV tuner can be activated so the installer can operate DVD without using the remote controller v Optional control port for installer s convenience to insert extra audio input to car s AUX port also to switch the original touch screen for installed aftermarket touch devices like touch navigation computer v This device is car temperature verified surge voltage stability testified 1 System connection Side key to switch the input Monitor s original plug should be inserted here Video out to the monitor eee oves ge ampate aa dyas NOLL
5. NVD 240 erPRErOBO6 atu haan at ONT 3008 aaddOud 4 corr N 00v PRED oy oe Users may long press the NAVI key to switch the input CAN box s 4Pin should be connected to the car s navi console connector 4Pin in this way Car Navi Console CAN Box 1 Yellow Red strip to RED with fuse 12V 2 Gray Orange to Blue CAN 2 WVinlet Qrange tn Grav The Ford monitor has a 4Pin LVDS connector connecting the CD Radio unit and the Monitor The connector to monitor should be inserted to this video interface s CAR In socket When the 3 side keys are pressed the selected item will traverse among the menu while will modify the values This OSD selection is only available to video input the RGB navi already been tuned to have nice color The DVD TUNER NAVI option is to set the IR output to the video source so the user can use touch screen to control DVD and other video source operations Disable this function by set the DVD TUNER NAVI type to None or do not connect the touch daught PCB to the Ctrl port set it to PROG if the DVD Tuner type if it is not listed inside Z 3m www fosp cn Fog CAN box output 6Pin POWER conn For the Interface box YELLOW 12V battery power it can also be ACC RED ACC whenthis wire goes to 12V the interface works BLACK Ground for chassis GREEN goto camera video when t
6. his wire 12V white switch signal when 12V max 25V GRAY specific control signal from the CAN box do not connect to anything Then the interface s LVDS tail plug should be inserted onto this monitor s rear socket Which was used by CD s 4Pin connector cture wie contrast Brightness Saturation eee PANASONIC HANTANG DDT FOSP Exit MENU Move 4 Sel FOgP 4 ix www fosp cn 2 The Ctrl port Ctrl port here The Ctr port has 8 pins it is not necessary for the installers to use it in most cases however it can be used for installer s convenience in case many more extra devices are installed Pin 1 Pin2 5V output voltage for sound switch All ford cars have an AUX stereo input which can be connected relay when AV1 is selected to the external audio input If the installer needs to send 2 or OV when AV2 selected more extra audio into the car speaker one mechanical relay max output 2A while most mechanical should be used to switch the sound This pin can pull the relay relay only needs 0 1 0 3A with 5V Pind constant SV when the unitisworking M ROAGMI Pin5 6 should NOT be connected to GND because it will halt the CPU inside Leave it open for normal use 5V output voltage for touch screen For imported cars which needs touch screen for installed switch relay navigation computer this voltage can be used to switch the when in inserted video mode th
7. is original touch screen pin 5V when in original car video mode this pin OV d LCV8F 7 M0 ae 7 AA AR CER ioe s Video LVDS gee ees BRAT ES ae ie oe ot os nee connector ma ergs OS ewes Touch panel connector 3 Touch screen operation Users may use the original touch panel for inserted navi operations which is needed for imported cars then the touch screen switch PCB is needed and should be wired in this way FOgP Z a www fosp cn To original touch panel 4P for inserted navi To Original touch socket To interface for switch voltage When the touch screen is not used for navigation it can also be used for DVD TV control for installed device Touch Screen Panel Enter Menu When this daughter PCB is inserted the user touch the panel this touch icons will pop out and the user can control DVD TV with it to socket To ctrl Port The 3 keys can choose the DVD TV type connected to this unit R 4 If the installer do not want these icons to pop out set the DVD TUNER options to be None DIP switch setting op on orr downsiee SS i 5 This is reverse camera trigger wire go to car video when Green wire 12V C en enemy Touch screen IR learn for re installed Setto OFF for normal use 4 Parameters no eme i ner RGB video amplitude 0 7Vpp with 75 ohm impedance 2 sync amplitude in RGB navi port 3 5Vpp with 5K ohm impedance
8. itter should be used on the iR DVD line The IR_RGB and IR_DVD send the IR code out in RGB AV1 and AV2 The video source choose to acknowledge because the data bytes values are different the 4 data bytes say the device by the first 2 and 3 byte says the key value the last one is the verification m When the installer use the IR RGB or IR_DVD without carrier frequency he needs to connect the IR output wire to the ir sensor s signal wire all ir sensors have 3 wires inside 5V GND and signal For imported cars USers may use the original touch panel for inserted navi operations which is very important for imported cars then the touch screen switch PCB is needed and should be wired in this way In this case the installer does not need the DVD touch Connect the relay s to pin7 and Connect the relay s to ping When the screen shows the inserted video RGB AV1 AV2 pin7 5V when the screens shows the original video pin7 OV When the relay is switched with 5V the 4Pin original touch is switched to the inserted navi
9. shared by installed extra device The daughter PCB is connected to the interface with this connector View on the interface Pin3 4 8 power supply Pin5 6 communication data bus Pin 1 2 5V when AV1 selected Pin 7 5V when in inserted video mode The control signal is wired to pini 2 so touch may be used for AV1 only default The installer may taked the pin out and wire it to Pin7 so touch may be used for whatever inserted video mode The input box has 3 side keys the installer may use it to tune the picture display and touch function for the connected DVD or other devices The 3 keys are menu wee Picture 7 JAAN 1 5 ogona Ea TTT I 5 rightness i Saturation 54 Sharpness 62 DVD PANASONIC PROG TUNER NAVI NONE When menu key pressed 1st time the left OSD options will be shown when pressed 2nd time the right OSD options will be shown when pressed 3rd time the osd window will disappear The user may use the key to go to the edit mode of each item and use menu key again to go down to the next item The DVD TUNER NAVI items mean the IR output of RGB AV1 AV2 input respectively there are already FOgP 4 a www fosp cn many types of DVD TV tuner and NAVI brands programmed inside The installer may also set it to be PROG if the video source brand is not listed inside Then he may pull the DIP6 DIP down to program the IR code The installer may also set it to be
Download Pdf Manuals
Related Search