PROJECTOR LIFT MODEL SI-30 INSTALLATION MANUAL
Contents
1. NW 576 mm M ie 7 A i 7 k 4 i E y CLOSED LIFT FRONTAL VIEW 224 M q la 553 mm 7 LI XW OoO e C S r3 EE g 3 L PEDA Lr EE Gg ou he e 2 E 2 x Reese ciem Se i _ n a r aa emer ns Se l 570 mm d TL 450 mm 60mm E kai OPEN LIFT SIDE VIEW CLOSED LIFT SIDE VIEW screenint2. PROJECTOR LIFT MODEL SI 30 INSTALLATION MANUAL Thank you for purchasing the new SI 30 Projector Lift The SI 30 is supplied with a set of components and accessories that make it suitable for installation for the majority of standard AV applications but note must be made of the restrictions that apply to the weight capability of this unit and not exceeded Projector lift SI 30 must be installed by specialized personnel only Before installing the projector lift please read the following instructions carefully e The projector lift must be used INDOORS ONLY e IT IS FORBIDDEN TO STAY UNDER THE LIFT e Please confirm that your projected image width will fit your screen from your proposed mounting location prior to installation e Incorrect use of the lift including exceeding the maximum lifting weight would be dangerous and invalidate the warranty e The manufacturer does not take responsibility for any damage to property or personal injury if the lift is used outside of recommended specifications This product uses a 230V AC Motor DO NOT attempt to service the motor Incorrect servicing could lead to risk of electric shock For any repairing please contact directly the dealer you purchased the unit from Check at least once a year that the screws of the steel cables are well tightened and that the steel cables are in good conditions In case they have signs of usage or damages replace them promptly with the original ones supplied by the manufa
3. cturer SUPPLIED EQUIPMENT LIST When you open the packaging please CHECK that it contains ALL the components below In case one or more components are missed please refer to the dealer you purchased the product from A 1 MECHANIC PROJECTOR LIFT SUPPLIED WITH A MOTOR WITH A 3 METRE POWER CABLE WITH FOUR ELECTRIC WIRES UP DOWN NEUTRAL AND EARTH B 4 L FORM ALUMINIUM BRACKETS FOR CEILING MOUNTING C ON OFF SWITCHER D PLASTIC SPIRAL TO COLLECT THE PROJECTOR CABLES E INSTALLATION MANUAL F 4 THREADED BARS M6 L 25 CM AND 2 MOUNTING PLATES FOR THE FALSE CEILING PLATE G 8 HEX HEAD SCREWS 6x16 MM H 16 NUTS M6 FOR MOUNTING THE THREADED BARS TO THE MOUNTING PLATES AND TO THE LIFT INSTALLATION INSTRUCTIONS Use the hex headed screws listed as G in the equipment list to mount the 4 L brackets to the profile of the lift as shown in pictures 1A and 1B below ami PICTURE 1A PICTURE 1B Mount the lift to the ceiling using suitable wall plugs NOT SUPPLIED and verify that the projector lift is perfectly horizontal using a sprit level Use shims to level the lift if required between the brackets and the ceiling Installing the lift perfectly level is IMPORTANT and ensures silent movement of the lift without any shaking jolting or friction that would compromise the alignment between projector and projection screen screenint screenint Once you have mounted the lift lower it till the end stop
4. eiling Mount the bars to the profile of the lift and fix them to the mounting plates using the M6 nuts supplied as in PICTURES 3A and 3B PICTURE 3A PICTURE 3B PROJECTOR LIFT WITH INSTALLED FALSE CEILING PANEL Fit in the false ceiling panel inside the profile of the mounting plates and check that the panel is aligned with the hole in the false ceiling If the panel is not balanced move the projector lift either releasing the screws that lock the L brackets to the aluminium profile making them sliding or releasing the screws that anchor the brackets to the ceiling using the sliding hole milled out of them max 3 cm the hole on the ceiling is central If the lift does not line up horizontally to the false ceiling modify the length of the bars or the UPPER END STOP following the instructions above described screenint TECHNICAL DATA POWER SUPPLY 220 230 V 50 Hz MAX CONSUMPTION 156 W TORQUE 10 Nm MOTOR SPEED 17 Rpm DIMENSIONS LIFT CLOSED for projectors max height cm 8 5 576x120x553 LxHxP in mm DIMENSIONI ELEVATORE CHIUSO for projectors max height cm 14 576x170x553 LxHxP in mm DIMENSIONS LIFT OPENED 576x440x553 LxHxP in mm MAXIMUM DIMENSIONS OF PROJECTOR 400x140x450 LxHxP in mm MAXIMUM CAPACITY 15 Kg NET WEIGHT PROJECTOR LIFT SI 30 11 Kg TECHNICAL DRAWINGS SS ren E k a La 1 Um TT ES p T35 mm i Af M z
5. preset by the factory approx 50 cm unscrews the screws as indicated in Picture 2A and 2B and open the brackets according to the height of your projector fit in the projector into the brackets and move the brackets along the aluminium profiles see Picture 2C according to the fixing points on the video projector Now remove the projector and tighten the side screws of the brackets taking care that the distance between the rear bracket and the rear side of the aluminium profile is the same as the distance between the front bracket and the front side of the aluminium profile see Picture 2D OPEN PROJECTOR LIFT PICTURE 2A PICTURE 2B SIDE VIEW WITH EQUIDISTANT BRACKETS PICTURE 2F LIFT WITH PROJECTOR COMPLETELY CONNECTED PICTURE 2E Slide the projector inside the bracket and fix it to the brackets using the screws as indicated on the projector s installation manual see Picture 2E Bring down from the ceiling at a length of approx 30 cm the power and signal cables of the projector Collect these cables using the supplied plastic spiral Using a wire clamp fix the spiral and cables to the upper part of the aluminium profile see Picture 2F taking care to guide the cables to the rear side of the projector Fix the end part of the spiral to the rear bracket using the other wire clamp supplied and successively connect the cables to the projector Connect the projector lift to the mains using the supplied switche
6. r following the instructions on Picture 2G Warning set the lower end stop see instructions here under for a maximum descent of 30 cm taking care that the spiral with cables does not interfere with the mechanism of the lift when it moves up and down The next step is to set the UPPER END STOP CLOSED lift and the LOWER END STOP OPEN lift If the projector lift has been positioned inside a false ceiling take care to set the upper end stop so that when the lift is in closed position the brackets will not touch the ceiling The LOWER END STOP has to be adjusted so that the image is correctly projected onto the screen In order to fix the UPPER END STOP _ O WARNING in case the installer needs to modify this end A Stop it is allowed to lower the upper end stop Do not try LM to high the upper end stop because this will cause severe damages to the product Turn the screw on the motor shown on the picture clockwise to lower the lift In order to fix the LOWER END STOP Turn the screw on the motor as shown on the picture counter clockwise to increase the lower end stop and clockwise to reduce it MAXIMUM ALLOWED DESCENT CM 30 UPPER END STOP Motora Motor Mateur Motor Matot LO md ee m o t LG 5 PICTURE 2G Once you have fixed the UPPER END STOP cut the threaded bars to the correct length according to the distance between projector and false c
Download Pdf Manuals
Related Search