PCI I/O User's Manual
Contents
1. In Minicom go to Serial Port Setup then Serial Device Change the modem to use port dev ttyS3 Set the baud rate to 38400 Save the changes as a dfl file Note We tested the serial port with RedHat Linux 6 0 with a Motorola Bitsurfr Pro EZ to run at 230Kb The procedure should work with earlier versions of RedHat Linux or other Linuxlike operating systems 2 2 7 Linux setup for PCI Parallel Port 1 Load addresses in kernel Define them as LPTO 1 and 2 use default addresses Default addresses LPTO 03BC 03BE LPT1 0378 037A LPT2 0278 027A 2 RedHat 6 0 use version 2 2 kernel or higher a b Load PCIUTILS using the SETUPPCI command ADD lines SETPCI V D 14db 2120 0OX10 L 0x278 SETPCI V D 14db 2120 0X14 L 0x678 2120 device ID it could be another ID number as following table according to the Model No you purchase Model No Device ID P008 2111 02 002D2. 1 PCI VO User s Manual Introducing the PCI I O Card The series products of PCI I O Card are high speed Plug and Play PCI add on cards which provide many combination functions of UART serial port and ECP EPP parallel port 1 1 PCI I O Card Product list Standard Slot Series Model No Product Name P001 1 Serial P002 1 Serial 16650 P018 1 Serial 16850 P003 Dual Serial P004 Dual Serial 16650 P019 Dual Serial 16850 P005 1 Parallel P006 Dual Parallel P007 1P1S P008 1P1S 16650 P020 1P1S 16850 P009 1P2S Function 1 16550 UART Serial 1 16650 UART Serial 1 16850 UART Serial 2 16550 UART Serial 2 16650 UART Serial 2 16850 UART Serial 1 ECP EPP Parallel 2 ECP EPP Parallel 1 16550 UART Serial and 1 ECP EPP Parallel 1 16650 UART Serial and 1 ECP EPP Parallel 1 16850 UART Serial and 1 ECP EPP Parallel 2 16550 UART Serial and 1 ECP EPP Parallel as P010 P021 1P2S 16650 1P2S 16850 Single Slot Series Model No P011 P012 P013 P028 P029 P030 P014 P015 P016 P017 P025 P026 P027 P022 P023 P024 Product Name AV 4 Serial AV 4 Serial 16650 AV 4 Serial 16850 AV 8 Serial AV 8 Serial 16650 AV 8 Serial 16850 AV 2 Parallel AV 1P2S AY 1P2S 16650 AYV 1P2S 16850 AV 2P1S AY 2P1S 16650 AY 2P1S 16850 AV 2P2S AY 2P2S 16650 AV 2P2S 16850 2 16650 UART Serial and 1 ECP EPP Parallel 2 16850 UART Serial and 1 ECP EPP Parallel Function 4 16550 UART Serial 4 166
3. 50 UART Serial 4 16850 UART Serial 8 16550 UART Serial 8 16650 UART Serial 8 16850 UART Serial 2 ECP EPP Parallel 2 16550 UART Serial and 1 ECP EPP Parallel 2 16650 UART Serial and 1 ECP EPP Parallel 2 16850 UART Serial and 1 ECP EPP Parallel 1 16550 UART Serial and 2 ECP EPP Parallel 1 16650 UART Serial and 2 ECP EPP Parallel 1 16850 UART Serial and 2 ECP EPP Parallel 2 16550 UART Serial and 2 ECP EPP Parallel 2 16650 UART Serial and 2 ECP EPP Parallel 2 16850 UART Serial and 2 ECP EPP Parallel 2 1 2 Key Features and Benefits Conforms to PCI v2 1 Plug and Play Full support for DOS Windows based and Linux based software Fast I O access speed reduces CPU load and improves system performance dramatically IRQ sharing feature eliminates IRQ conflicts 1 3 Special Features and Benefits According to the Model No you purchase PCI I O card providesome advanced special features to your PC system 1 3 1 16850 UART Serial High speed 16850 UART serial port 9 pin supports baud rates up to 920Kbps Works with 56K external modems ISDN terminal adapters and other serial port devices Built in 128 byte FIFO buffers dramatically increase data transmit receive speed especially under Windows multitasking environment 1 3 2 16650 UART Serial High speed 16650 UART serial port 9 pin supports baud rates up to 920Kbps Works with 56K external mod
4. O Card Windows will notify you of New Hardware Found 2 Select Driver from disk provided by hardware manufacturer and click OR 3 Insert the Driver Installation diskette in the floppy drive and type in a win95 and click on OK 4 Remove the diskette and restart the computer 2 2 4 Windows NT 4 0 Driver Installation 1 Goto Start and Run Insert the Driver Installation diskette in the floppy drive and type in aAntA setup then click on OR 3 The Intek 21 PCI IO Welcome windows will appear Click on Next and Next again 4 Fromthe next Setup Complete window select Yes I want to restart my computer now and click on Finish 6 Remove the diskette and restart the computer for the setup to take effect Note Ifyou plan to connect a parallel device other than a printer such as zip drive scanner etc to the port please follow the next section to change the I O address for the port to support the device To change the I O address 1 Go to Start Setting Control Panel double click on Itk PCI IO device icon 2 Hightlight the LPT address and click on setting 3 Select or type in an I O address supported by the device and click on 4 OK Make sure the selected I O address does not conflict with other in your system Select Restart Now for the new setup to take effect 2 2 5 DOS Windows 3 x Driver Installation 1 Insert Driver Installationdisket
5. ems ISDN terminal adapters and other serial port devices Built in 32 byte FIFO buffers dramatically increase data transmit receive speed especially under Windows multitasking environment 356 1 3 3 16550 UART Serial High speed 16550 UART serial port 9 pin supports baud rates up to 920Kbps Works with 56K external modems ISDN terminal adapters and other serial port devices Built in 16 byte FIFO buffers dramatically increase data transmit receive speed especially under Windows multitasking environment 1 3 4 ECP EPP Parallel High speed parallel port support all types of parallel port devices including removable cartridge drives CDR RWs printers SuperDisk LS 120 drives scanners and more Supports EPP ECP PIO mode Bi directional Parallel Port BPP and Standard Parallel Port SPP modes Data Transfer rates up to 2MB sec Installation Guide 2 1 Hardware Installation 1 Tur OFF the power to your computer and any other connected Peripheral devices 2 Unplug the power cord from the back of the computer 4 3 Remove the computer s cover select an available 32 bit PCI slot and remove the bracket Save the screw for securing the board after it s installed 4 To install the PCI T O card Align the board s connector to the expansion slot on the motherboard Push the board down gently until it is well seated 5 Replace the slot bracket holding screw to secure the board
6. te in the floppy drive and from the Sic FBS C gt prompt type in copy aldos and press lt enter gt Type in edit autoexec bat and press lt Enter gt Add CNTK21adr exe atthe bottom of the autoexec bat file Go to file save the changes and exit Remove the floppy diskette and restart the systemfor the new setup to take effect 2 2 6 Linux setup for PCI Serial Port 1 2 gt A Boot with a DOS or Windows Startup Disk Run the utility ITK21MOD EXE in the DOS folder on the Installation Disk to set the baud rate to 921 6Kb The default baud rate setting is 115200 on the card Ifno high speed is required you don t need to run this utility Boot to Linux Go to the proc directory Use vi to open the pci file NS po 10 11 12 13 14 Search for vendor ID 14db Write down the port address and IRQ number for example 0xd400 and IRQ 12 Go to the dev directory Use the setserial command to set up the serial port setserial ttyS3 port 0xd400 uart 16550A irq 12 baud_base 921600 spd_cust divisor 4 ttyS3 port number could be ttyS4 if the system already have three serial ports installed uart UART type use 16550A if the UART is 16550 spd_cust set custom speed divisor baud rate divide by the divisor number equals to modem data transfer speed If the baud_base is set to 921600 then the divisor has to be 4 to get a transfer speed of 230Kb Run Minicom configuration utility by typing minicom s
7. to the rear slot panel 6 Replace the computer cover and reconnect the power cord Restart the system and refer to the next section for Software Installation 2 2 Software Installation 2 2 1 Windows 2000 Driver Installation 1 At the Add New Hardware Wizard windows click on Next 2 Select the option Search for the best driver for your devices Recommend and click on Next 3 Select the option Specify the location insert the Driv er Installation diskette in the floppy drive and type ina Awin2000 and click on Next 4 Click on Nex and then Finish respectively 5 Remove the diskette and restart the computer 2 2 2 Windows 98 Driver Installation At the Add New Hard ware Wizard windows click on Next Select the option Search for the best driver for your devices Recommend and click on Next Select the option Specify the location insert the Driver Installation diskette in the floppy drive and type in a Awin98 and click on Next Click on Next and then Finish respectively 5 Remove the diskette and restart the computer w Ne A 2 2 3 Windows 95 Driver Installation For proper installation in your system verify the version of Windows 95 in your system by going to My Computer Control Panel System General Then follow the steps below to install the Windows 95 drivers 1 When you first turn on your computer after installing the PCI I
Download Pdf Manuals
Related Search