Home
CPC1100 User Manual - Rosch Computer GmbH
Contents
1. Table 2 4 ISA Bus Connector Pinout 1 IOCHCHK GND SBHE MEMCS16 2 SD7 RESETDRV LA23 IOCS16 3 SD6 5V LA22 IRQ10 4 SD5 IRQ LA21 IRQ11 5 SD4 5V LA20 IRQ12 6 SD3 DRQ2 LA19 IRQ15 7 SD2 12V LA18 IRQ14 8 SD1 ENDXFR LA17 DACKO 9 SDO 12V MEMR DRQO 10 IOCHRDY GND MEMW DACK5 11 AEN SMEMW SD8 DRQ5 12 SA19 SMEMR SD9 DACK6 13 SA18 IOW SD10 DRQ6 14 SA17 IOR SD11 DACK7 15 SA16 DACK3 SD12 DRQ7 16 SA15 DRQ3 SD13 5V 17 SA14 DACK1 SD14 MASTER 18 SA13 DRQ1 SD15 GND 19 SA12 REFRSH 20 SA11 SYSCLK 21 SA10 IRQ7 22 SA9 IRQ6 23 SA8 IRQ5 24 SA7 IRQ4 25 SA6 IRQ3 26 SA5 DACK2 27 SA4 TC 28 SA3 BALE 29 SA2 5V 30 SA1 OSC 31 SAO GND CPC1100 User Manual 2 7 2007 Fastwel Ver 001 E Detailed Description Fastwel TS CPC1100 2 3 2 Serial Interfaces RS232 and RS485 Serial interfaces are available via four onboard 10 pin IDC connectors J22 J23 J24 and J38 Both COM1 and COM2 ports are software switchable between two modes RS232 and optoisolated RS485 Each port uses two separate connectors for these operation modes All COM ports are fully compatible with the 16550 controller and include a complete set of handshaking and modem control signals maskable interrupt generation and data transfer of up to 460 8 Kb s Figure 2 1 IDC10 Header The following table gives the pinouts of the onboard serial IDC connectors
2. Table 2 5 RS232 Connector J22 J23 Pinout 1 DCD 6 CTS 2 DSR 7 DTR 3 RXD 8 RIN 4 RTS 9 GND 5 TXD 10 NC Table 2 6 RS485 Connector J24 J38 Pinout 1 TRXD 6 NC 2 TRXD 7 NC 3 GND 8 NC 4 GND 9 GND 5 NC 10 GND Note The RS485 interface provides for support of up to 256 network segments In case the board is supposed to serve as a terminal network device it is necessary to use a special cable with terminal resistors supplied with the board 2 3 3 USB Interfaces The CPC1100 supports eight USB 2 0 ports two sockets are available via CPC1100 board slot bracket front panel and six more via three 10 pin onboard IDC connectors All USB ports support high speed full speed and low speed operation Hi speed USB 2 0 supports data transfer rate of up to 480 Mb s CPC1100 User Manual 2 8 2007 Fastwel Ver 001 E Detailed Description Fastwel TS CPC1100 One USB device may be connected to each port To connect more than eight USB devices use an external hub The USB power supply is protected by a self resettable 500 mA fuse Figure 2 2 Front Panel USB Connectors 4321 The CPC1100 has two identical 4 pin Type A USB connectors J11 and J12 on the front panel with the following pinouts poes 4321 Table 2 7 Front Panel USB Connectors Pinouts 1 VCC VCC signal 2 UVO Differ
3. CPC1100 User Manual 2 16 2007 Fastwel Ver 001 E Fastwel TZ CPC1100 Detailed Description 2 3 10 Floppy Drive Interface Figure 2 10 FDD Connector The CPC1100 is provided with a 2 row 34 pin standard IDC onboard FDD connector which provides the signals for up to two floppy disk drives The onboard floppy disk controller supports either 5 25 inch or 3 5 inch 1 44 or 2 88 MB floppy disks Warning Pay attention to the correct connection of the floppy drive cable Please note that cable inversion will lead to continuous operation of the floppy drive this may damage the diskette in it Table 2 16 FDD Connector Pinout 2 SELECTO Density Select 0 Out 4 NC S 6 SELECTI Density Select 1 Out 8 INDEX Index pulse In 10 MOTENI Motor 1 enable Out 12 DRVSEL2 Driver select 2 Out 14 DRVSEL1 Driver select 1 Out 16 MOTEN2 Motor 2 enable Out 18 DIRECTION Step direction Out 20 STEP Step pulse Out 22 WRDATA Write data Out 24 WREN Write enable Out 26 TRACKO Track 0 signal In 28 WRPROT Write protect In 30 RDDATA Read data In 32 HEADSEL Head select Out 34 DSKCHG Disk change In Odd Numbers GND GND CPC1100 User Manual 2007 Fastwel Ver 001 E Detailed Description Fastwel Ley CPC1100 2 3 11 MiniPCI Socket Figure 2 11 MiniPCI Socket The J26 onboard connector is a Type IIIB 124 contact MiniPCI socket It allows in
4. Figure 2 13 Figure 2 14 Figure 4 1 GPC1100 Block DiagraM s siii iaa ai aa 1 5 CPC1100 Board Appearance i 1 6 GPC1100 Board Layout iveco lei lai iaia nidi 1 7 PGI Express Edge Conectividad 2 5 PGI Edge Connectors heat is 2 6 ISA WE ee 2 7 SVUGA Real e 2 11 RJ45 Ethernet Connectors ccccceccccessneeeeseeeeeceeeeeeesenaeeeseeneeecesaeeeescaeeeescaeeeesenaeeeeseaeeeescsaeesseseeessneeess 2 11 2 12 HDD LED Connector viii en es 2 14 Serial ATA Connector nn ran R RR RRA R RR RR INR RRE RR NNR RR R RON R RR RR RR EEEE EEEE 2 14 LIPT Connector siii eebe 2 16 am o E 2 17 MINIPE Sockets di ia 2 18 IDG 10 Audio Gonnector anna ee Hana 2 19 Fan Connector een na Hell ala un 2 20 External ATX Power Supply Connector ii 2 20 FSB Frequency Selection ii 4 1 CPC1100 User Manual 0 3 2007 Fastwel Ver 001 E Fastwel LE CPC1100 All information in this document is provided for reference only with no warranty of its suitability for any specific purpose This information has been thoroughly checked and is believed to be entirely reliable and consistent with the product that it describes However Fastwel accepts no responsibility for inaccuracies omissions or their consequences as well as liability arising from the use or application of any product or example described in this document Fastwel Co Ltd reserves the rights to change modify and improve this document or the produ
5. Introduction Fastwel Ley CPC1100 1 3 2 Board Appearance Figure 1 2 CPC1100 Board Appearance The appearance may vary for different versions of the board The front retaining bracket rear mounting bracket CPU heatsink and fan are not shown CPC1100 User Manual 1 6 2007 Fastwel Ver 001 E Introduction Fastwel ZE CPC1100 1 3 3 Board Layout Figure 1 3 CPC1100 Board Layout CPU Heatsink and Fan Site 4 x1 PCI Express ATX Power CPU Soft Power Switch Reset Switch HDD LED GMCH amp Heatsink CPU Fan 32 bit PCI Systeman Mini P CI FSB Frequency Selection Switch 2 DDR2 DIMM Sockets D ICH6 Lithium Battery Clear CMOS 285232 16 bit ISA 2 RS485 Opto Flash BIOS 6 USB 2 0 4 SerialATA LPT Audio FDD PS 2 Keyboard Mouse CF Type Il bottom side IDE HDD VGA 2 USB 2 0 Gigabit F ast Ethernet Gigabit Ethernet The layout may slightly differ for various versions of the board CPC1100 User Manual 2007 Fastwel Ver 001 E Introduction Fastwel LE CPC1100 1 4 1 4 1 CPU Memory Chipset Technical Characteristics Processor Memory and Chipset The CPC1100 supports the following Intel processor family Pentium M Processor 90 nm Dothan n Up to 2 0 GHz E Up to 2 MB L2 on die cache D 400 533 MHz PSB E Supports SpeedStep III for low power mode Main memory n Up to 2 GB of DDR2 SDRAM memory in two 240
6. The chipset s built in video controller incorporates a 2D 3D graphics accelerator with up to 64 MB memory shared with system for enhanced graphics performance with VGA CRT display CPC1100 offers two Gigabit Ethernet ports or optionally one Gigabit and one Fast Ethernet which make this board highly suitable for network rich infrastructure CPC1100 supports storage devices with IDE UltraATA 100 and CompactFlash interfaces up to four SerialATA channels and standard FDD In addition to PICMG 1 0 parallel 16 bit ISA and 32 bit PCI buses CPC1100 board supports up to four serial PCI Express x1 channels or one x4 channel Besides one MiniPCI expansion module can be installed directly on the board Extra reliability of CPC1100 is provided by the hardware monitoring subsystem This prevents accidental damage to the hardware under unfavourable thermal conditions CPC1100 is manufactured using high quality embedded industrial system components specially selected to ensure their long term availability CPC1100 board usage model includes La PICMG 1 0 CPU card in a PICMG passive backplane system for example in standard 5U industrial servers fal Full size PICMG CPU card with customized active backplane providing PCI Express to PCI bridge or other bridging hardware along with PCI and ISA buses n CPC1100 as a standalone card for slim industrial backplaneless servers The board is compatible with the Microsoft Windows 2000 XP CE QNX and Li
7. carefully take the product out of the shipping carton box Proper handling of the product is critical to ensure correct operation and long term reliability When unpacking the product and whenever handling it thereafter be sure to hold the module preferably by the front panel card edges or ejector handles Avoid touching the components and connectors Retain all original packaging at least until the warranty period is over You may need it for shipments or for storage of the product Initial Inspection Although the product is carefully packaged it is still possible that shipping damages may occur Careful inspection of the shipping carton can reveal evidence of damage or rough handling Should you notice that the package is damaged please notify the shipping service and the manufacturer as soon as possible Retain the damaged packing material for inspection After unpacking the product you should inspect it for visible damage that could have occurred during shipping or unpacking If damage is observed usually in the form of bent component leads or loose socketed components contact Fastwel s official distributor from which you have purchased the product for additional instructions Depending on the severity of the damage the product may even need to be returned to the factory for repair DO NOT apply power to the product if it has visible damage Doing so may cause further possibly irreparable damage as well as result in a fire or electri
8. interface The chipset supports up to PC4200 dual or single channel DDR2 SDRAMs for use as system memory When running in internal graphics mode high performance video capabilities of the 915GM are supported by a 2D 3D graphics accelerator and H W Motion Compensation engines for software MPEG2 decoding The internal graphics controller allows connection of a standard CRT display South Bridge The ICH6 ICH6M is a multifunctional I O Controller Hub that provides interfaces to the PCI Express and PCI buses and to a number of PC interfaces such as UltraDMA 100 66 33 USB 2 0 host interface LPC interface FWH Flash BIOS interface SATA and an AC 97 digital audio The ICH communicates with the host controller directly via a dedicated DMI interface 1 0 Controller Hub features are PCI 2 3 interface with eight IRQ inputs PCI Express Bus four 1x or one 4x Bus Master EIDE controller UltraDMA 100 66 33 SATA interface four channels two for ICH6M USB controller supporting eight USB 2 0 ports DMI interface with 915GM LPC interface AC 97 2 1 interface or High Definition audio interface RTC controller Additional timer CPC1100 User Manual 2 2 2007 Fastwel Ver 001 E Detailed Description Fastwel TS CPC1100 2 2 Internal Peripherals The following internal peripherals are available on the CPC1100 module 2 2 1 Flash Memory There are two flash devices available one is used for the BIOS storage and one isa CompactFlash card
9. J4 J5 The details on these jumper switches and their usage can be found in Chapter 4 of this Manual CPC1100 User Manual 9 21 2007 Fastwel Ver 001 E Detailed Description Fastwel TS CPC1100 CPC1100 User Manual 9 22 2007 Fastwel Ver 001 E Chapter 3 Installation Installation Fastwel Ee CPC1100 3 Installation The CPC1100 is easy to install However it is necessary to follow the procedures and safety regulations below to install the module correctly without damage to the hardware or harm to personnel The installation of the peripheral drivers is described in the accompanying information files For details on installation of an operating system please refer to the relevant software documentation 3 1 Safety Regulations The following safety regulations must be observed when installing or operating the CPC1100 Fastwel assumes no responsibility for any damage resulting from infringement of these rules Warning When handling or operating the module special attention should be paid to the heatsink because it can get very hot during operation Do not touch the heatsink when installing or removing the module Moreover the module should not be placed on any surface or in any kind of package until the module and its heatsink have cooled down to ambient temperature Caution If your module does not allow hotswapping switch off the system power before installing the module in a free slot Disregarding th
10. Table 2 1 SMBus Devices 1 0D2H CY28411 System clock generator 2 OAOH SPD EEPROM Module 3 0A2H SPD EEPROM Module 4 9CH LM87 Temperature Sensor 2 2 3 1 Temperatures Monitoring The integrated LM87 temperature sensor monitors the processor and board surface temperatures to make sure that the system is operating at a safe temperature On request LM87 can report the current processor and board temperatures to the software responsible for the module operation mode 2 2 3 2 Serial EEPROM SPD serial EEPROM is a part of DIMM memory module This nonvolatile memory is used by the system and is not available for user 2 2 4 Battery The CPC1100 utilizes a 3 0 V lithium battery for the RTC and CMOS memory backup Use PANASONIC BR2032 or compatible CPC1100 User Manual 2 4 2007 Fastwel Ver 001 E Detailed Description Fastwel TS CPC1100 2 3 Module Interfaces 2 3 1 Edge Connectors CPC1100 is equipped with three edge connectors PCI Express PCI and ISA PCI and ISA edge connectors location conforms to the PICMG 1 0 specification The PCI Express edge connector has been added to further expand the board s I O capabilities 2 3 1 1 PCI Express Edge Connector The CPC1100 PCI Express interface is fully compliant with the PCI Express 1 0a specification It supports four PCI Express root ports and can be statically configured as four x1 or one x4 lanes Two virtual channels are supported for full isochronous data transfers PCI Express
11. Vibration 15G 2G Power Supply 3A 3 3V 7A 5V 0 12 A 12 V to be amended See Chapter 6 for details on supply voltages and power supply requirements Temperature Ranges Operational 10 C 70 C Storage 55 C 95 Humidity 5 to 95 RH non condensing CPC1100 User Manual 1 11 2007 Fastwel Ver 001 E Introduction Fastwel Top CPC1100 Battery 3 0 V lithium battery for RTC in a battery holder Use PANASONIC BR2032 or compatible 1 4 5 Software Software BIOS Flash memory based enhanced Phoenix BIOS has the following features n BIOS boot support for USB keyboards n Software enable disable function for the Ethernet and COM ports configuration n Plug amp Play capability Operating Systems Supported operating systems E Microsoft DOS v 3 30 6 22 n Microsoft Windows 2000 XP CE XP Embedded a Linux E QNX v 4 20 6 0 1 5 Delivery Checklist The CPC1100 supplied set includes 1 CPC1100 SBC CD ROM with documentation and service software Antistatic bag Consumer carton box Cables to be specified a na Note Keep the antistatic bag and the original package at least until the warranty period is over It can be used for future storage or warranty shipments CPC1100 User Manual 1 12 2007 Fastwel Ver 001 E Chapter 2 Detailed Description Detailed Description Fastwel Ley CPC1100 2 Detailed Description 2 1 Processor Memory and Chipset 2 1 1 Processor T
12. heatsink have cooled down to room temperature 3 4 Peripheral Devices Installation Many peripheral devices can be connected to the CPC1100 Their installation procedures differ significantly Therefore the following sections provide mainly general guidelines regarding installation of peripheral devices The details on external devices connection can be found in documentation supplied with these devices 3 4 1 USB Devices Installation The CPC1100 can accept Plug amp Play connection of USB 2 0 computer peripheral devices printers keyboards mice etc All USB devices may be connected or disconnected while the host power is on CPC1100 User Manual 3 3 2007 Fastwel Ver 001 E Installation Fastwel LE CPC1100 3 4 2 CompactFlash Cards Installation CompactFlash socket of CPC1100 supports only 3 3 V CompactFlash ATA type UI cards Note Connection of the CompactFlash cards while the power is on may damage your system Carefully slide in the correctly oriented card and gently press to engage the contacts completely Note It is recommended to use CompactFlash cards which has been initialized and formatted in this module By default CPC 1100 utilizes LBA mode Utilization of CompactFlash cards which has been initialized and formatted in another mode may lead to errors in operation of the module 3 4 3 Battery Replacement The lithium battery must be replaced with Panasonic BR2032 or a battery with similar cha
13. in the socket 2 2 1 1 CompactFlash The CPC1100 has a standard Compact Flash type I II socket which can accept CompactFlash memory card for use as a disk drive connected to IDE channel The CompactFlash socket is located on the bottom side of the board 2 2 2 Timers CPC1100 is equipped with the following timers E RTC Real Time Clock The ICH contains a MC146818A compatible real time clock The RTC includes 256 bytes of battery backed CMOS RAM The RTC features include timekeeping with alarm function and 100 year calendar as well as programmable periodic interrupt A coin cell battery powers the real time clock and CMOS memory M Counter Timer Three 8254 type counters timers are available on the CPC1100 M Additional Timer The ICH includes an additional programmable timer which prevents system hang ups during start ups After the first time out period is over it generates the SMI signal which starts the software hang up recovery subroutine If the second timeout ends the Reset signal is issued to recover the system from the hardware hang up state CPC1100 User Manual 2 3 2007 Fastwel Ver 001 E Detailed Description Fastwel TS CPC1100 2 2 3 Local SMBus Devices The CPC1100 incorporates a System Management Bus to access several system monitoring and control devices via a two wire I C bus interface The following table presents functions and addresses of onboard SMBus devices
14. interface provides full 2 5 Gb s bandwidth in each direction per x1 lane This interface is available only in special customized version of CPC1100 Figure 2 1 PCI Express Edge Connector CPC1100 is equipped with PCI Express edge connector which allows for data exchange via four x1 lanes or one x4 lane depending on software configuration ge ge The pinout is presented below Table 2 2 PCI Express Bus Connector Pinout PCIE_A1 GND PCIE_A16 GND PCIE_B1 GND PCIE_B16 GND PCIE_A2 HSOp 0 PCIE_A17 REFCLK1 PCIE_B2 REFCLK2 PCIE_B17 HSOn 3 PCIE_A3 HSOn 0 PCIE_A18 REFCLK1 PCIE_B3 REFCLK2 PCIE_B18 HSOp 3 PCIE_A4 GND PCIE_A19 GND PCIE_B4 GND PCIE_B19 GND PCIE_A5 HSIn 0 PCIE_A20 3_3V PCIE BS HSIp 2 PCIE_B20 3_3V PCIE_A6 HSIp 0 PCIE_A21 SMBCLK PCIE B6 HSIn 2 PCIE_B21 3_3V_AUX PCIE A7 GND PCIE_A22 SMBDATA PCIE_B7 GND PCIE_B22 PRSNT 2_SO PCIE_A8 REFCLKO PCIE_A23 3_3V PCIE_B8 HSOn 2 PCIE_B23 PRSNT 2_S1 PCIE_A9 REFCLKO PCIE_A24 PRSNT 1_SO PCIE_B9 HSOp 2 PCIE_B24 PRSNT 2_S2 PCIE_A10 GND PCIE_A25 PRSNT 1_S1 PCIE_B10 GND PCIE_B25 PRSNT 2_S3 PCIE_A11 HSOp 1 PCIE_A26 PRSNT 1_S2 PCIE_B11 REFCLK3 PCIE_B26 PWRGD_SO PCIE_A12 HSOn 1 PCIE_A27 PRSNT 1_S3 PCIE_B12 REFCLK3 PCIE_B27 PWRGD_S1 PCIE_A13 GND PCIE_A28 WAKE PCIE_B13 GND PCIE_B28 PWRGD_S2 PCIE_A14 HSIn 1 PCIE_A29 12V PCIE_B14 HSI
15. into the chosen slot until it contacts the baseboard connectors Make sure the rear mounting bracket slides along the guide 3 Check whether edge connectors are properly aimed and gently press until the edge connectors are fully engaged with the baseboard connectors Do not apply extra force pushing the module into the baseboard connectors Fix the module by screwing in the board slot bracket with retaining screw Connect the required external interfacing cables to the module s connectors and make sure that the module and all connected cables are properly fixed The CPC1100 is now ready for operation Please refer to appropriate software application and system manuals to get further instructions CPC1100 User Manual 3 2 2007 Fastwel Ver 001 E Installation Fastwel ZE CPC1100 3 3 Removal Procedure To remove the module from the system case do the following 1 When performing the next actions keep to safety regulations of the Section 3 1 Pay special attention to the temperature of the heatsink Ensure that the system power is switched off before proceeding Disconnect all cables that may be connected to the module Unscrew the board slot bracket retaining screw D fF UN Carefully pull the module out of the slot Do not touch the heatsink since it can get very hot during operation 7 Dispose of the module at your discretion The module should not be placed on any surface or in any form of package until the board and the
16. pin DIMM sockets n Memory frequency 533 MHz PC4200 Flash memory n 1 MB flash memory Firmware Hub a part of the chipset for BIOS storage E CompactFlash card in CF Type I II socket Intel 82915GM Graphics and Memory Controller Hub GMCH n Intel Pentium M processor with 2 MB L2 cache support 533 MHz PSB D Intel Pentium M processor LV and ULV support 400 MHz PSB z 32 bit host bus addressing 12 deep in order queue Enhanced Intel SpeedStep technology E Intel Celeron M and Celeron M ULV 90 nm processor support 400 MHz PSB 7 32 bit host bus addressing support 12 deep in order queue support 64 bit AGTL AGTL based PSB interface at 400 533 MHz 64 bit System Memory interface optimized for DDR or DDR2 SDRAM memory operating at 400 or 533 MHz DDR2 dual channel memory symmetric and asymmetric modes Integrated 2D 3D Graphics and H W Motion Compensation Engines Integrated DAC 400 MHz Intel Graphics Media Accelerator 900 Intel Stable Image Technology Intel I O Controller Hub 6 ICH6 82801FB or ICH6M 82801FBM option a PCI Express bus with four PCI Express root ports PCI Bus rev 2 3 interface at 33 MHz Integrated Serial ATA host controller Integrated IDE controller Ultra ATA100 BMIDE and PIO modes Intel High Definition or AC97 Audio Interface USB 2 0 host interface CPC1100 User Manual 1 8 2007 Fastwel Ver 001 E Introduction Fastwel TL CPC1100 Integrated Fast Ethernet LAN co
17. 0 ft above sea level Important Some versions of the module may have the test results differing from the ones presented in the above table For more information please contact Fastwel s official representatives CPC1100 User Manual B 1 2007 Fastwel Ver 001 E Information related to this product and its components can be found in the following specifications Table A 2 Related Specifications PICMG PICMG 1 0 Rev 2 0 PCI Bus PCI 2 3 Compliant Specifications For latest revision of the PCI specifications contact the PCI Special Interest Group Office at http www pcisig com PCI Express PCI Express 1 0a Specification MiniPCI MiniPCI Specification Rev 1 0 CompactFlash Cards CF and CompactFlash Specification Revision 4 1 The Internet site of the PCI Industrial Computer Manufacturers Group PICMG provides information related to these standards http www picmg org CPC1100 User Manual 2007 Fastwel Ver 001 B 2 E Appendix B Useful Abbreviations Acronyms and Short cuts BMC Baseboard Management Controller PM Peripheral Management Controller IPMI Intelligent Platform Management Interface IPMB Intelligent Platform Management Bus DC Inter Integrated Circuit Two thread serial protocol used in SMB and IPMI KCS interface Keyboard Controller Style interface Interface for communicatio
18. 001 E Fastwel LZ CPC1100 2 3 8 CompactFlash Socket nano nc rra 2 15 2 3 9 Parallel Port Interface acicate iris 2 16 2 3 10 Floppy Drive INterTace ocicoriicia irlanda SR pia era iii 2 17 2 3 11 MINIPCI Socket e a 2 18 2 3 12 Keyboard Mouse Interface coi lia a AERA alla 2 19 2 3 13 Audio gel Ee 2 19 2 3 14 Fal CONNEC OS ar ie LARIO Siae NATIA ILARIA idad dba 2 20 2 3 15 ATX Power Connector ii 2 20 2 3 16 Other ConmectOrs gue Eege ENEE e 2 21 3 Installation ucraini ia ri iii 3 1 3 1 Safety Ee IER TEE 3 1 3 2 Installation Procedure coco tido alii 3 2 3 3 Removal tele TEE 3 3 3 4 Peripheral Devices Installation i 3 3 3 4 1 USB Devices Installation i 3 3 3 4 2 CompactFlash Cards Installation i 3 4 3 4 3 Battery Replacement nn 3 4 4 G nfig rat EE 4 1 4 1 Clear CMOS Jumper Description 4 1 4 2 FSB Frequency Selection Switch 4 1 4 3 Interrupts Handling EE 4 2 4 3 1 On board PCI Interrupts i 4 2 ENN Tee TT 4 3 4 4 1 First Megabyte Memory Map 4 3 4 4 2 PO Addresses alia io 4 3 5 Phoenix CHE 5 1 5 1 Boot RTE 5 1 5 1 1 Booting without a Monitor Keyboard or Mouse cnn nana nonnnnn cnn cane nnnnnnnes 5 1 5 1 2 BOOting Tom USB casitas Bere nenn as 5 1 6 Thermal and Power ISSUES uussusnnannsnnannnnnunnunnnnnnnnnnnnannunnnnnnnnnnnnannnnnnnnnnnnnnnnnnnnnnnnnnnnn
19. 10 SVGA Front Panel Connector PiNOUt naar nnnnnnnn nn nrnnn nn nnnn nn nrnnnnnnnannnnnos 2 11 Front Panel Ethernet Connectors Pinouts i 2 12 Standard EIDE HDD Connector Pinout nn nennnnnnnannnnrnnnnnaninnnss 2 13 SATA Connector Die TEE EE 2 14 CompactFlash Socket Pinot 2 15 LPT Connector Pinout nn neon nn nn nn RR RR nn RR RR RR RRE RRA R RR REIR RR RRnR RR rn nnnn rr nrnnnnrnnnnnnno 2 16 FDD Connector Pinout r n Reine iaia 2 17 MiniPCI Connector Pinout e 2 18 PS 2Gonnector 421 Pinout E E E iaia boris 2 19 Audio Gonnector PinoUt a spread ata 2 19 Controllable Fan J33 Connector Pinot 2 20 Uncontrollable Fan J32 Connector PiNOUt iii 2 20 ATX Power Supply Connector PiNOUt ii 2 20 INterrupi SEtlings a iii ali e ili nisi ii ali 4 2 PGl Interrupt Routingi isla alan Lei ida ee ee 4 2 First Megabyte Memory Map ici IRE li iaia 4 3 ef EN E10 EE 4 3 DC Input Voltage Ranges and Limite 6 3 Some CPC1100 Components Power Consumption nan cn ron cc ran can cnn r rra 6 3 Related Standards nn rra A R RRE R RR R RR RR RRRR RR RR A T A 1 Related Specifications iii filiali alal iaia A 2 List of Figures Figure 1 1 Figure 1 2 Figure 1 3 Figure 2 1 Figure 2 2 Figure 2 3 Figure 2 4 Figure 2 5 Figure 2 6 Figure 2 7 Figure 2 8 Figure 2 9 Figure 2 10 Figure 2 11 Figure 2 12
20. A Controller DMA Controller DMA 09h 0Eh RESERVED DMA Controller DMA OFh DMA Controller DMA Controller DMA 10h 18h DMA Controller DMA Controller DMA 19h 1Eh RESERVED DMA Controller DMA 1Fh DMA Controller DMA Controller DMA 20h 21h Interrupt Controller Interrupt Controller Interrupt 24h 25h Interrupt Controller Interrupt Controller Interrupt 28h 29h Interrupt Controller Interrupt Controller Interrupt 2Ch 2Dh Interrupt Controller Interrupt Controller Interrupt 2E 2F LPC SIO LPC SIO Forwarded to LPC 30h 31h Interrupt Controller Interrupt Controller Interrupt 34h 35h Interrupt Controller Interrupt Controller Interrupt 38h 39h Interrupt Controller Interrupt Controller Interrupt 3Ch 3Dh Interrupt Controller Interrupt Controller Interrupt 40h 42h Timer Counter Timer Counter PIT 8254 43h RESERVED Timer Counter PIT 4E 4F LPC SIO LPC SIO Forwarded to LPC 50h 52h Timer Counter Timer Counter PIT 53h RESERVED Timer Counter PIT 60h Microcontroller Microcontroller Forwarded to LPC 61h NMI Controller NMI Controller Processor I F 62h Microcontroller Microcontroller Forwarded to LPC 64h Microcontroller Microcontroller Forwarded to LPC 66h Microcontroller Microcontroller Forwarded to LPC 70h RESERVED NMI and RTC Controller RTC 71h RTC Controller RTC Controller RTC CPC1100 User Manual 4 3 2007 Fastwel Ver 001 E Configuration Fastwel LE CPC1100 72h R
21. CI_A44 AD15 PCI_B13 GND PCI B44 C BE1 PCI_A14 GNT1 PCI_A45 3_3V PCI_B14 CLKA PCI_B45 AD14 PCLA15 RST PCI_A46 AD13 PCI_B15 GND PCI_B46 GND PCI_A16 5V_IO PCI_A47 AD11 PCI_B16 CLKB PCI_B47 AD12 PCI_A17 GNTO PCI_A48 GND PCILB17 GND PCI_B48 AD10 PCI_A18 GND PCI_A49 AD9 PCI B18 REQO PCI_B49 GND PCLA19 REQ2 PCI_B19 5V_IO PCI_A20 AD30 PCI_B20 AD31 PCLA21 3 3V PCI_A52 C_BEO PCI_B21 AD29 PCI_B52 AD8 PCI_A22 AD28 PCI_A53 3_3V PCI_B22 GND PCI_B53 AD7 PCI_A23 AD26 PCI_A54 ADE PCI_B23 AD27 PCI_B54 3_3V PCI_A24 GND PCI_A55 AD4 PCI_B24 AD25 PCI_B55 ADS PCI_A25 AD24 PCI_A56 GND PCI_B25 3 3V PCI_B56 AD3 PCI A26 GNT2 PCI_A57 AD2 PCI B26 C_BE3 PCI_B57 GND PCI_A27 3 3V PCI_A58 ADO PCI_B27 AD23 PCI_B58 ADI PCI_A28 AD22 PCI_A59 5V_IO PCI_B28 GND PCI_B59 5V_IO PCI_A29 AD20 PCI_A60 REQ64 PCI_B29 AD21 PCI_B60 ACK64 PCI_A30 GND PCI_A61 5V PCI_B30 AD19 PCI_B61 5V PCI_A31 AD18 PCI_A62 5V PCI_B31 3 3V PCI_B62 5V CPC1100 User Manual 2 6 2007 Fastwel Ver 001 E Detailed Description Fastwel TS CPC1100 2 3 1 3 ISA Edge Connector Figure 2 3 ISA Edge Connector CPC1100 is equipped with 16 bit ISA 98 contact 0000000000000000005 OA AT A io UA edge connector C18 C1 A31 Al The pinout is presented below ISA connector pinout appears on the following page
22. Fastwel TS CPC1100 PICMG Intel Pentium M Based Processor Board User Manual Rev 001 E April 2007 The product described in this manual is compliant to all related CE standards Product Title CPC1100 Document Name CPC1100 User Manual Manual Version 001E Copyright 2007 Fastwel Co Ltd All rights reserved Revision Record Contact Information Fastwel Co Ltd Fastwel Corporation US Address 108 Profsoyuznaya st 45 Main Street Moscow 117437 Suite 319 Russian Federation New York 11201 Tel 7 495 232 1681 1 718 554 36 86 Fax 7 495 232 1654 1 718 797 06 00 E mail info fastwel com mailto info fastwelcopr com Web http www fastwel com Fastwel LE CPC1100 Table of Contents RK Ee 0 1 LSU el E E 0 3 istot le iran A ani 0 3 Notation Gonventionsi liri ET ein aio 0 4 General Safety Precautions E 0 5 Unpacking Inspection and HandliNg ie 0 6 Three Year Warranty 42 ie He ia andai A 0 8 1 Introduction eegene dee 1 1 1 1 ENEE eebe eege eege 1 1 i2 e en bloe WE TEE 1 3 1 3 CPETTOO DiagramSs c c lei iii iene 1 4 1 3 1 Block Diagram area La a paia aid 1 5 1 3 2 Board Appeara ue 1 6 1 3 3 Board Layouts ai palle ia 1 4 Technical Characteristics 1 4 1 Processor Memory and Chipset i 1 8 1 4 2 Interfacos icsuupri n ari ea iaia 1 9 1 4 3 Control and Monitoring i 1 11 1 4 4 General aa 1 11 1 4 5 SONWANE E 1 12 E Se e
23. Out 20 A00 Address 0 Out 21 D00 Data 0 In Out 22 D01 Data 1 In Out 23 D02 Data 2 In Out 24 NC IOCS16 25 NC CD2 26 NC CD1 27 D11 Data 11 In Out 28 D12 Data 12 In Out 29 D13 Data 13 In Out 30 D14 Data 14 In Out 31 D15 Data 15 In Out 32 IDE_CS1 Chip select 1 Out 33 NC VS1 u u 34 DIOR I O read Out 35 DIOW I O write Out 36 3 3 V WE 3 3 V power 37 INTRQ Interrupt In 38 3 3 V 3 3 V power 39 CSEL GND pull up Master Slave Out 40 NC VS2 41 Reset Reset Out 42 IORDY UO ready In 43 REQ DMA request Out 44 ACK DMA acknowledge In 45 NC ACTIVE 46 NC PDIAG 47 D08 Data 08 In Out 48 D09 Data 09 In Out 49 D10 Data 10 In Out 50 GND CPC1100 User Manual 2 15 2007 Fastwel Detailed Description Fastwel EN CPC1100 2 3 9 Parallel Port Interface Figure 2 9 LPT Connector 2 26 Standard parallel port IEEE1284 SPP ECP EPP is available through a 26 pin onboard IDC connector To use standard parallel port devices a special adapter is necessary Table 2 15 LPT Connector Pinout 1 STROBE Out 14 GND 2 AUTOFD Out 15 PD6 In Out 3 PDO In Out 16 GND 4 ERROR In 17 PD7 In Out 5 PD1 In Out 18 GND _ 6 INIT Out 19 ACK In 7 PD2 In Out 20 GND _ 8 SLCTIN Out 21 BUSY In 9 PD3 In Out 22 GND 10 GND 23 PE In 11 PD4 In Out 24 GND 12 GND 25 SLCT In 13 PD5 In Out 26 GND
24. PCI X bus traffic and a PCI X interface providing efficient bus utilization by increased use of bursts The interfaces provide auto detection and switching between 10Base T 100Base TX and 1000Base T operation modes Each of the two Ethernet channels may be disabled via the BIOS Setup or user software utility to free up system resources CPC1100 User Manual 2 11 2007 Fastwel Ver 001 E Detailed Description Fastwel TS CPC1100 2 3 5 1 RJ45 Connectors Pinout RJ45 connectors supply the 10Base T 100Base TX and 1000Base T interfaces to the front panel board slot bracket of CPC1100 Table 2 11 Front Panel Ethernet Connectors Pinouts 1 O TX O TX I O BI_DA 2 O TX O TX 1 0 BI_DA 3 I RX RX 1 0 BI_DB 4 8 u I O BI_DC 5 1 0 BI_DC 6 RX I RX 1 0 BI_DB 7 _ 1 0 BI_DD 8 I O BI_DD MDI Standard Ethernet Cable Integrated Ethernet LEDs Yellow Line This LED indicates network connection The LED lights up when the line is connected Green Act this LED monitors network activity The LED lights up when network packets are sent or received through the RJ45 port When this LED is not lit it means that the computer is not sending or receiving network data 2 3 6 EIDE Interface The EIDE interface supports several operation modes PIO mode 8237 type DMA mode Ultra DMA ATA 66 and ATA 100 modes In PIO mode the central processor controls the d
25. RT monitor to the CPC1100 module The 75 ohm termination resistors for the red green and blue video signals are installed on the CPC1100 Table 2 10 SVGA Front Panel Connector Pinout 1 Red Red video signal output Out 2 Green Green video signal output Out 3 Blue Blue video signal output Out 9 VCC Power 5V 200 mA Out 12 DDCdata IPCTM data In Out 13 Hsync Horizontal sync TTL out 14 Vsync Vertical sync TTL out 15 DDCclk IC clock Out 5 6 7 8 GND Signal ground 4 10 11 Free 2 3 5 Ethernet Ports Figure 2 5 RJ45 Ethernet Connectors Two RJ45 Ethernet connectors are located on CPC1100 front panel board slot bracket Depending on the board version they are used by two Gigabit Ethernet interfaces or by one Fast and one Gigabit Ethernet ports Version 01 has two 10Base T 100Base TX 1000Base T Ethernet ports based on Intel 82573 Gigabit Ethernet PCI Express bus controllers Version 02 is equipped with one Gigabit Ethernet port 82573 on PCI Express bus and one Fast Ethernet port 82562ET The Intel 82573 Gigabit Ethernet controller architecture combines high performance and low power consumption The controller s features include independent transmit and receive queues to limit
26. TC Controller NMI and RTC Controller RTC 73h RTC Controller RTC Controller RTC 74h RTC Controller NMI and RTC Controller RTC 75h RTC Controller RTC Controller RTC 76h RTC Controller NMI and RTC Controller RTC 77h RTC Controller RTC Controller RTC 80h DMA Controller or LPC or PCI DMA Controller and LPC or PCI DMA 81h 83h DMA Controller DMA Controller DMA 84h 86h DMA Controller DMA Controller and LPC or PCI DMA 87h DMA Controller DMA Controller DMA 88h DMA Controller DMA Controller and LPC or PCI DMA 89h 8Bh DMA Controller DMA Controller DMA 8Ch 8Eh DMA Controller DMA Controller and LPC or PCI DMA 08Fh DMA Controller DMA Controller DMA 90h 91h DMA Controller DMA Controller DMA 92h Reset Generator Reset Generator Processor I F 93h 9Fh DMA Controller DMA Controller DMA AOh Ath Interrupt Controller Interrupt Controller nterrupt A4h A5h Interrupt Controller Interrupt Controller nterrupt A8h A9h Interrupt Controller Interrupt Controller nterrupt ACh ADh Interrupt Controller Interrupt Controller nterrupt Boh B1h Interrupt Controller Interrupt Controller nterrupt B2h B3h Power Management Power Management Power Management B4h B5h Interrupt Controller Interrupt Controller nterrupt B8h B9h Interrupt Controller Interrupt Controller nterrupt BCh BDh Interrupt Controller Interrupt Controller nterrupt Coh Dih DMA Controller DMA Controller DMA D2h DDh RESERVED DMA Controller DMA DEh DFh DMA Controller DMA Controller DMA Foh PCI and Master Abort1 FERR IGNNE I
27. _AUDIO_IN_GND 35 AD 29 77 GND_7 119 AUDIO_GND2 36 RSVD7 78 AD 13 120 AUDIO_GND3 37 GND_3 79 AD 12 121 RSVD4 38 AD 30 80 AD 11 122 MPCIACT 39 AD 27 81 AD 10 123 VCC5VA 40 3 3V_6 82 GND_14 124 3 3VAUX2 41 AD 25 83 GND_8 42 AD 28 84 AD 09 CPC1100 User Manual 2 18 2007 Fastwel Ver 001 E Detailed Description Fastwel EN CPC1100 2 3 12 Keyboard Mouse Interface Figure 2 4 PS 2 Keyboard Mouse Connector 00808080 PS 2 port is available via the 7 contact single row onboard J21 connector Mouse and keyboard can be connected simultaneously 7 1 using Y cable supplied with CPC1100 The pinout of this connector is shown in the table below Table 2 18 PS 2 Connector J21 Pinout 1 VCC5V 5 MCLK 2 KBDDAT 6 GND 3 KBDCLK 7 NC 4 MDAT Note All keyboard mouse signal lines are EMI filtered 2 3 13 Audio Connector Figure 2 12 IDC 10 Audio Connector 10 A number of audio interfaces are available via an onboard IDC 10 connector J31 Please find its pin destination below Table 2 19 Audio Connector Pinout 1 LINE OUT L 6 LINE_IN_R 2 LINE_OUT_R 7 GND 3 GND 8 GND 4 GND 9 MIC_IN 5 LINE_IN_L 10 MIC_BIAS CPC1100 User Manual 2 19 2007 Fastwel Ver 001 E Detailed Description Fastwel Ley CPC1100 2 3 14 Fan Connectors Figure 2 13 Fan Connector There are two 3 pin 2 54 mm fan connectors mounted on the CPC1100 bo
28. actions should be performed when the power is disconnected Figure 4 1 FSB Frequency Selection The contact pins 1 and 2 are closed on both J4 and J5 jumper switches FSB frequency is defined by the CPU CPU defined FSB frequency D 1 n E o 8 E The contact pins 2 and 3 are closed on both J4 and J5 jumper switches FSB frequency is set to 533 MHZ The contact pins 2 and 3 on J5 are closed and J4 contacts are open FSB frequency is set to 400 MHZ CPC1100 User Manual 4 1 2007 Fastwel Ver 001 E Fastwel TZ Configuration CPC1100 4 3 Interrupts Handling Interrupt handling of the CPC1100 module corresponds to the standard AT IRQ mapping 8259 IRQ controller integrated in the chipset The functions of the interrupts described below are the default ones but can be modified via the BIOS Setup Table 4 1 Interrupt Settings IRQO 1 System Timer IRQ1 2 Keyboard Controller IRQ2 Second IRQ controller input IRQ8 IRQ15 IRQ3 11 COM2 IRQ4 12 COMI IRQ5 13 Reserved IRQ6 14 Floppy Disk Controller IRQ7 15 LPT IRQ8 3 System RTC IRQ9 4 PCI or ACPI IRQ10 5 PCI or Ethernet ports IRQ11 6 PCI IRQ12 7 PCI or PS 2 mouse IRQ13 8 Coprocessor error IRQ14 9 Primary IDE channel IRQ15 10 Secondary IDE channel NMI Reserved 4 3 1 On board PCI Interrupts The ICH handles up to 8 PCI interrupt inputs The table below describes the conne
29. additional cable adapters For customized board versions CPC1100 User Manual 1 2 2007 Fastwel Ver 001 E Introduction Fastwel ZE CPC1100 1 2 CPC1100 Versions At the present time the board is offered in flexible configuration The options include different processors the size of supplied system memory and other options described in this section The customer can choose necessary configuration options using the following template 1 Basic product name CPC1100 2 Configuration version 01 Two Gigabit Ethernet channels 02 One Fast Ethernet and one Gigabit Ethernet channel 3 Processor P1 4 Pentium M 1 4 GHz 400 MHz FSB P1 8 Pentium M 1 8 GHz 400 MHz FSB P2 0 Pentium M 2 0 GHz 533 MHz FSB 4 Other options DIMM memory module DIMM512 512 MB DDR2 SDRAM DIMM DIMM1024 1024 MB DDR2 SDRAM DIMM Cooling COOLER Heatsink with fan installed CompactFlash Module CF128 128 MB CompactFlash card CF256 256 MB CompactFlash card CF512 512 MB CompactFlash card CF1024 1024 MB CompactFlash card Operating System DOS DOS XPE Windows XP Embedded QNX QNX WCE Windows CE 5 0 LNX Linux 2 4 20 Example CPC1100 02 P1 8 DIMM512 COOLER CF128 XPE PICMG Pentium M Intel 915GM DDR2 SVGA PCI_E SATA 1 Fast Ethernet 1 Gigabit Ethernet Pentium M 1 8 GHz 400 MHz FSB 512 MB DDR2 SDRAM DIMM Heatsink amp fan installed 128 MB CompactFlash card Windows XP Embed
30. and EIDE devices n Up to two devices hard disks or CD ROMs E 40 pin onboard IDC connector Serial ATA interface E Up to four onboard connectors two with ICH6M E Data transfer rates up to 150 MB s CompactFlash E CompactFlash type I II on board socket true IDE mode supports type or type Il CompactFlash cards E DMA modes supported as per CompactFlash Specification v 4 1 Floppy Disk interface n Supports 5 25 or 3 5 inch floppy drives D 1 44 or 2 88 MB 3 5 inch floppy disks E 34 pin onboard IDC connector CPC1100 User Manual 1 10 2007 Fastwel Ver 001 E Introduction Fastwel Ee CPC1100 1 4 3 Control and Monitoring Thermal Management The processor is protected from overheating by a Internal processor temperature control unit which initiates CPU shut down a Processor die temperature monitor n Heatsink Temperature Monitor LM87 hardware monitor is used for supervision of the on die CPU temperature and the board surface temperature LEDs option System status E Suspend Power On red n IDE SATA activity onboard header E Power LED green Gigabit Fast Ethernet status 1 and 2 n Line green Line connected a Act green Network activity Reset Input n Onboard reset header Soft Power On E Onboard soft power header ATX Power Supply n 20 contact standard ATX power connector 1 4 4 General Mechanical PICMG form factor Dimensions 122 x 338 mm Board Weight 305 g to be amended Shock
31. ard They are used for connection of cooling fans J33 for CPU cooling fan J32 for system fan The pinout of these connectors is presented in the table below Table 2 20 Controllable Fan J33 Connector Pinout 1 GND 2 CTRL 3 TACH Table 2 21 Uncontrollable Fan J32 Connector Pinout 1 GND 2 12V 3 NC 2 3 15 ATX Power Connector Figure 2 14 External ATX Power Supply Connector i So The standard 2 row 20 pin connector for ATX power supply is located on the board near the processor socket The pinout of this connector is shown in the table below 11 20 Table 2 22 ATX Power Supply Connector Pinout 1 3 3V 11 3 3V 2 3 3V 12 12V 3 GND 13 GND 4 5V 14 PSON 5 GND 15 GND 6 5V 16 GND 7 GND 17 GND 8 PWROK 18 5V 9 5VSB 19 5V 10 12V 20 5V CPC1100 User Manual 2 20 2007 Fastwel Ver 001 E Detailed Description Fastwel Ley CPC1100 2 3 16 Other Connectors A group of three 2 pin connectors next to memory sockets consists of Soft Power switch connector J29 Reset switch connector J30 and HDD LED connector J8 J29 and J30 are used for connection of standard remote control buttons Moreover the board has a 2 pin Clear CMOS jumper switch J7 and 6 pin FSB Frequency Selection Switch
32. ata transfers In all the DMA modes the CPU is not engaged in data transfer DMA modes are similar to each other but differ in data transfer protocols details and DMA clock frequency thus providing different transfer rates The module s chipset ATA 100 logic can provide transfer rates of up to 100 MB sec read and up to 88 MB sec write The current version of CPC1100 supports one EIDE channel to accommodate a maximum of two devices Figure 2 6 HDD Connector The EIDE channel is routed to standard AT 40 pin on board IDC connector J16 and to the CompactFlash socket It is possible to connect both master and slave devices to this EIDE channel Maximum IDE cable length is 50 cm The pinout of the standard AT HDD connector is shown in the table below CPC1100 User Manual 2 12 2007 Fastwel Ver 001 E Detailed Description Fastwel Le CPC1100 Table 2 12 Standard EIDE HDD Connector Pinout 1 IDERESET Reset HD Out 2 GND Ground signal 3 HD7 HD data 7 In Out 4 HD8 HD data 8 In Out 5 HD6 HD data 6 In Out 6 HD9 HD data 9 In Out 7 HD5 HD data 5 In Out 8 HD10 HD data 10 In Out 9 HD4 HD data 4 In Out 10 HD11 HD data 11 In Out 11 HD3 HD data 3 In Out 12 HD12 HD data 12 In Out 13 HD2 HD data 2 In Out 14 HD13 HD data 13 In Out 15 HD1 HD data 1 In Out 16 HD14 HD data 14 In Out 17 HDO HD data 0 In Ou
33. being static discharge can be sufficient to destroy or degrade a component s operation Therefore all handling operations and inspections of this product must be performed with due care in order to keep product integrity and operability a Preferably unpack or pack this product only at EOS ESD safe workplaces Otherwise it is important to be electrically discharged before touching the product This can be done by touching a metal part of your system case with your hand or tool It is particularly important to observe anti static precautions when setting jumpers or replacing components If the product contains batteries for RTC or memory back up ensure that the module is not placed on conductive surfaces including anti static mats or sponges This can cause short circuit and result in damage to the battery and other components E Store this product in its protective packaging while it is not used for operational purposes Unpacking The product is carefully packed in an antistatic bag and in a carton box to protect it against possible damage and harmful influence during shipping Unpack the product indoors only at a temperature not less than 15 C and relative humidity not more than 70 Please note that if the product was exposed to the temperatures below 0 C for a long time it is necessary to keep it at normal conditions for at least 24 hours before unpacking Do not keep the product close to a heat source Following ESD precautions
34. bility it is necessary to handle it with care and follow the ESD safety directions Warning This sign marks warnings about hot surfaces The surface of the heatsink and some components can get very hot during operation Take due care when handling avoid touching hot surfaces Caution Electric Shock This symbol warns about danger of electrical shock gt 60 V when touching products or parts of them Failure to observe the indicated precautions and directions may expose your life to danger and may lead to damage to your product Warning Information marked by this symbol is essential for human and equipment safety Read this information attentively be watchful Note This symbol and title marks important information to be read attentively for your own benefit SE gt b gt CPC1100 User Manual 0 4 2007 Fastwel Ver 001 E Fastwel LE CPC1100 General Safety Precautions This product was developed for fault free operation Its design provides conformance to all related safety requirements However the life of this product can be seriously shortened by improper handling and incorrect operation That is why it is necessary to follow general safety and operational instructions below A A amp Warning All operations on this device must be carried out by sufficiently skilled personnel only Warning When handling this product special care must be taken not to hit the heatsink if installed agai
35. board CPC1100 User Manual 1 9 2007 Fastwel Ver 001 E Introduction Fastwel Top CPC1100 Parallel Port Multi Mode bidirectional parallel port Standard Mode IBM PC XT PC AT and PS 2 compatible SPP standard rate EPP Enhanced Parallel Port v 1 7 and 1 9 compatible ECP Extended Capability Port compatible n 26 pin IDC connector on board LAN Interface Two 10 100 1000 Mb s Gigabit Ethernet interfaces one Fast Ethernet and one Gigabit Ethernet interfaces option based on the Intel 82573 Ethernet PCI E bus controllers a Two RJ45 connectors at the board slot bracket O Automatic mode recognition E Automatic cabling configuration recognition n Cabling requirement Category 5 UTP four two pair cabling VGA Interface Built in Intel 2D 3D high performance graphics accelerator D Supports resolutions of up to 2048 x 1536 16 bit at 75 Hz refresh rate n Hardware motion compensation for software MPEG2 and MPEG4 decoding n Video memory up to 64 MB shared with system n 15 pin D sub VGA CRT display connector at the board slot bracket Audio Interface AC 97 compatible LM4550 audio codec a 10 pin IDC connector on board Line In Out Microphone In Keyboard and Mouse Super UO support for PS 2 keyboard and mouse Available via a 7 pin connector on board n Mouse and keyboard simultaneous connection is possible via Y cable Mass Storage EIDE Ultra ATA 100 66 33 E One channel is shared by CompactFlash interface
36. c shock hazard If the product contains socketed components they should be inspected to make sure they are seated fully in their sockets CPC1100 User Manual 0 6 2007 Fastwel Ver 001 E Fastwel LE CPC1100 Handling In performing all necessary installation and application operations please follow only the instructions supplied by the present manual In order to keep Fastwel s warranty you must not change or modify this product in any way other than specifically approved by Fastwel or described in this manual Technical characteristics of the systems in which this product is installed such as operating temperature ranges and power supply parameters should conform to the requirements stated by this document Retain all the original packaging you will need it to pack the product for shipping in warranty cases or for safe storage Please pack the product for transportation in the way it was packed by the supplier When handling the product please remember that the module its components and connectors require delicate care Always keep in mind the ESD sensitivity of the product CPC1100 User Manual 0 7 2007 Fastwel Ver 001 E Fastwel TZ CPC1100 Three Year Warranty Fastwel Co Ltd Fastwel warrants that its standard hardware products will be free from defects in materials and workmanship under normal use and service for the currently established warranty period Fastwel s only responsibility under this warra
37. cted to these PIRQs PCI devices and their functions Table 4 2 PCI Interrupt Routing PIRQA PCI IRQA or MINI PCI Socket USB 1 0 controller 1 PIRQB PCI IRQB or MINI PCI Socket AC97 MODEM SMBUS PIRQC PCI IRQC Storage IDE SATA native mode PIRQD PCI IRQD USB 1 0 controller 2 PIRQE Free Free PIRQF Free Free PIRQG Free Free PIRQH Security USB 2 0 controller The details can be found in the ICH technical documentation CPC1100 User Manual 4 2 2007 Fastwel Ver 001 E Configuration Fastwel Lee CPC1100 4 4 Memory Maps The CPC1100 module employs the standard AT ISA memory mapping The details of memory mapping are presented in the following subsections 4 4 1 First Megabyte Memory Map The following table shows the memory map for the first megabyte Table 4 3 First Megabyte Memory Map 0xE0000 OxFFFFF 128 k BIOS implemented in FWH Reset vector OxFFFFO 0xD0000 OxDFFFF 64 k Free 0xCC000 OxCFFFF 16 k Free 0xC0000 0xCC800 48 k VGA card BIOS 0xA0000 OxBFFFF 128 k Normally used as video RAM according to CGA 0xB8000 0xBFFFF Monochrome 0xB0000 0xB7FFF EGA VGA 0xA0000 0xAFFFF 0x00000 Ox9FFFF 640 k DOS memory space 4 4 2 I O Addresses The following table presents the I O memory mapping Table 4 4 UO Address Map 00h 08h DM
38. cts described in it at Fastwel s discretion without further notice Software described in this document is provided on an as is basis without warranty Fastwel assumes no liability for consequential or incidental damages originated by the use of this software This document contains information which is property of Fastwel Co Ltd It is not allowed to reproduce it or transmit by any means to translate the document or to convert it to any electronic form in full or in parts without antecedent written approval of Fastwel Co Ltd or one of its officially authorized agents Fastwel and Fastwel logo are trademarks owned by Fastwel Co Ltd Moscow Russian Federation Ethernet is a registered trademark of Xerox Corporation IEEE is a registered trademark of the Institute of Electrical and Electronics Engineers Inc Intel is a trademark of Intel Corporation Pentium M and Celeron M are trademarks of Intel Corporation Microsoft is a trademark of the Microsoft corporation In addition this document may include names company logos and trademarks which are registered trademarks and therefore are property of their respective owners Fastwel welcomes suggestions remarks and proposals regarding the form and the content of this Manual Notation Conventions Warning ESD Sensitive Device This symbol draws your attention to the information related to electro static sensitivity of your product and its components To keep product safety and opera
39. ded CPC1100 User Manual 1 3 2007 Fastwel Ver 001 E Introduction Fastwel ZE CPC1100 1 3 CPC1100 Diagrams The diagrams in this section give visual information about the CPC1100 board design its appearance connectors and components layout The diagrams may not reflect insignificant differences between the CPC1100 versions and generations w CPC1100 User Manual 1 4 2007 Fastwel Ver 001 E Introduction Fastwel Ee CPC1100 1 3 1 Block Diagram Figure 1 1 CPC1100 Block Diagram Hardware Monitor Intel Pentium M Two Dothan DDR2 DRAM CK 409 amp HFOPGA478 Sockets SS Clocking Up to 2 GB FSB 400 533 MHz E 6 915GM lt GMCH 5 1257uFCBGA gt CFII N E DMI Interface 35 a SATA q Ports 1 4 H S Fast Ethernet 1 un 82562ET g USB Ports 3 4 H Bi o 3 USB F cd Lei P h 2 Etherneti orts 5 6 z0 82573V o Gi al a o USB als a Ports 7 8 WK o 3 el 2 3 e Gigabit g Ss Ethernet2 82573V Super I O eene a LPC47M107 a RS232 Port 2 RS485 Port 1 Isolated AC97 RS485 Port 2 CPU Core VR GMCH VR DDR VR Mini PCI Connector Power Supply PS 2 LPC ISA Bridge W83626F 4 PCI E x1 32 bit PCI Bus 16 bit ISA Bus The block diagram may not reflect recent design changes The LPC ISA bridge can be replaced by a PCI ISA one CPC1100 User Manual 1 5 2007 Fastwel Ver 001 E
40. des use of all available memory in the most efficient way for maximum graphics performance DVMT dynamically responds to requests from applications allocating the required amount of video memory The Intel 915GM graphics driver is allowed to request up to 64 MB of system memory When not needed by the graphics subsystem the memory is freed up for other applications Thus memory usage is balanced for optimal graphics and system memory performance To support legacy VGA devices the internal video controller needs at least 1 MB of system memory Thus the reported system memory size is always 1 MB less than available amount of physical memory 2 3 4 2 Supported Resolutions The integrated 400 MHz RAMDAC of the 915GM chipset allows direct connection of a progressive scan analog monitor with a resolution of up to 2048 x 1536 at 75 Hz The supported resolution depends on the color depth and on the vertical scanning frequency as illustrated in the table below Table 2 9 Supported Display Modes 640 x 480 800 x 600 x x x x 1024 x 768 x x x x 1280 x 1024 x x x x 1600 x 1200 x x x x 1920 x 1440 x x x 2048 x 1536 CPC1100 User Manual 2 10 2007 Fastwel Ver 001 E Detailed Description Fastwel TS CPC1100 2 3 4 3 CRT Interface and Connector Figure 2 4 SVGA Connector The 15 contact female J10 D Sub connector on CPC1100 front panel board slot bracket is used to connect a C
41. e E E 1 12 2 Detailed Descriptioni 2 2 0 ea iaia ice 2 1 2 1 Processor Memory and Chipset con n cnn n cra nn rana 2 1 2 1 1 gel 2 1 2 1 2 System Memonm isre iieiea conocen 2 1 2 1 3 le E 2 1 2 2 Internal Peripherals omnia 2 3 2 2 1 SE EE 2 3 2 2 1 1 CompactFl sh 2 40 4 10 een enter at 2 3 2 2 2 TME S EE 2 3 2 2 3 Local SMBus DEVICES coccion A A ia Ia at ade etl 2 4 2 2 3 1 Temperatures Monitoring ii 2 4 2232 Serial EEPROM ae aan ea dice il ed 2 4 2 2 4 SE EE 2 4 2 3 Module Interfaces ccoo ii lai 2 5 2 3 1 Edge Connectors scri ie 2 5 2 3 1 1 PCI Express Edge Connector ca nnn cnn arrancar 2 5 2 3 1 2 PCI Edge Connector uunsneersnnensnnensnnennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nn 2 6 2 3 1 3 ISA Edge Connector 2 7 2 3 2 Serial Interfaces RS232 and RS485 rn cn nan nn nan cn ran naran cn ran narran 2 8 2 3 3 USB Interfaces comia 2 8 2 3 4 Graphics Controller iii alii pae 2 10 2 3 4 1 BYM Technology 2 ee eek 2 10 2 3 4 2 Supported ResolutiohS ii 2 10 2 3 4 3 CRT Interface and Connector cece ceeeeeeeeeneeeeeeeeeeeeeeeeeeeseeeseaeeeeeeseaeeeneeeseaeeeaaes 2 11 2 3 5 Ethernet POIs iss saciccvciscenssiazeicees ia 2 11 2 3 5 1 RJ45 Connectors Pinot 2 12 2 3 6 EIDE luc 2 12 2 3 6 1 HDD LED Connector 2 14 2 3 7 Senal ATA POMS acsee aikee enina ie ipa eil LA 2 14 CPC1100 User Manual 0 1 2007 Fastwel Ver
42. e to modify basic system configuration settings and switching between the subsystems operation modes These settings are stored in a dedicated battery backed memory CMOS RAM which keeps the information when the power is switched off 5 1 Boot Details 5 1 1 Booting without a Monitor Keyboard or Mouse To boot without a monitor keyboard or mouse set the item POST Errors to Disabled at the page Main in PhoenixBIOS Setup program This setting is a default one 5 1 2 Booting from USB To boot from a device connected to USB m Connect the device to boot from to a USB port The appropriate USB controller should be enabled a Enter the PhoenixBIOS Setup program E Find this USB device in Boot Priority list at the Boot page and use or buttons to move it up or down in order to change its boot priority In case the device is not in the Boot Priority list find it in Excluded from Boot Order list press x to move it to the Boot Priority list and set the boot order with Or buttons a Save changes and reboot the module To get the on line help about the details of BIOS Setup program operation please apply to the screen tips and the integrated help system CPC1100 User Manual 5 1 2007 Fastwel Ver 001 E Phoenix BIOS Setup Fastwel ZE CPC1100 CPC1100 User Manual 5 2 2007 Fastwel Ver 001 E Chapter 6 Thermal and Power Issues Thermal and Power Issues Fastwel ZE CPC1100 6 Ther
43. el Ver 001 E Thermal and Power Issues Fastwel Ee CPC1100 6 2 System Power The Intel Pentium M processor family requires special characteristics of the power supply unit and the baseboard The CPC1100 module itself has been designed to provide best possible power supply for each system unit However in order to guarantee reliable and faultless operation the following requirements must be taken into account Absolute maximum input voltages presented in the table below must not be exceeded to guarantee that the CPC1100 is not damaged The ranges for the different input power voltages within which the module is functional are also presented Table 6 1 DC Input Voltage Ranges and Limits 3 3 3 6 3 2 to 3 47 3 3 to 3 47 5 5 5 49 to 5 25 5 0 to 5 25 12 14 0 114 to 12 6 12 14 0 11 4 to 12 6 Power supplies to be used with the CPC1100 should comply with these requirements Input power connections to the baseboard itself should provide minimum power loss Avoid using long input lines low carrying capacity cables and high resistance connections To select the appropriate system power supply it is necessary to consider the CPC1100 own power consumption about 35 watts the consumption of the remaining system components possible variations of power consumption during operation e g due to temperature changes and some reserve Taking all this into account it is recommended to use a 150 watt pow
44. ential USB In Out 3 UVO Differential USB In Out 4 GND GND signal Figure 2 3 IDC10 Header Six more USB ports are available via three onboard 10 pin IDC connectors J13 J14 and J15 with the following pinouts Table 2 8 Onboard USB Connectors Pinouts 1 VCC VCC signal 3 UVO Differential USB 5 UVO Differential USB 7 GND GND signal 9 NC 2 VCC VCC signal 4 UVO Differential USB _ 6 UVO Differential USB 8 GND GND signal 10 NC Note The maximum current for each USB port is limited to the amount of 0 5 A by the board s circuitry All signal lines are EMI filtered CPC1100 User Manual 2 9 2007 Fastwel Ver 001 E Detailed Description Fastwel EN CPC1100 2 3 4 Graphics Controller A highly integrated 2D 3D graphics accelerator is included in the 915GM GMCH The internal graphics controller provides interfaces to a standard analog monitor SVGA connector on CPC1100 front panel Integrated 2D 3D Graphics features E Resolutions up to 1600x1200 at 100 Hz 1920x1440 at 85 Hz and 2048x1536 at 75 Hz 3D Setup and Render Engine 3D Graphics Rasterization Enhancements High Quality Texture Engine Full 2D hardware acceleration Intel 915GM DVMT graphics core Intelligent Memory Management Integrated 400 MHz DAC 2 3 4 1 DVM Technology The Intel 915GM chipset supports the Dynamic Video Memory Technology DVMT v 3 0 This technology provi
45. er supply If possible power supplies with voltage sensing should be used This may require an appropriate baseboard Table 6 2 Some CPC1100 Components Power Consumption Pentium M 1 6 CPU 24 5 W 915GM ICH6M Chipset 6 2 3W DDR SDRAM SODIMM PC2700 1 GB 2 5 V 5W Gigabit Ethernet chips 2pcs 1548x2 mW CompactFlash card 3 3 V 100 to 300 mW Keyboard 5 V 100 mW CPC1100 User Manual 6 3 2007 Fastwel Ver 001 E Thermal and Power Issues Fastwel ZE CPC1100 CPC1100 User Manual 6 4 2007 Fastwel Ver 001 E Appendices Appendix A A Supplementary Information A 1 Related Standards and Specifications The Fastwel s PICMG modules comply with the requirements of the following standards Table A 1 Related Standards CE Emission EN50081 1 CE Immission EN61000 6 2 CE Electrical safety EN60950 H Mechanical dimensions IEEE 1101 10 Vibration sinusoidal 1EC60068 2 6 82 Fc 5g 10 500 Hz 10 acceleration frequency range test cycles per axis Permanent shock 1EC60068 2 29 87 Eb 509 11 ms 1000 10 1 s peak acceleration shock duration half sine number of shocks recovery time Single shock IEC60068 2 27 87 Ea 1009 9ms 18 3s peak acceleration shock duration number of shocks recovery time in seconds Reduced atmospheric pressure IEC 60068 2 13 83 M 9 kPa 1 305 psi approx corresponds to 17000 m over 5570
46. ge the product in the antistatic bag in which the product had been supplied Failure to package in antistatic material will VOID all warranties Then package the product in a safe container for shipping 4 The customer pays for shipping the product to Fastwel or to an official Fastwel representative or dealer CPC1100 User Manual 0 8 2007 Fastwel Ver 001 E Chapter 1 Introduction Introduction Fastwel ZE CPC1100 1 Introduction 1 1 Overview The product described in this Manual is CPC1100 a full length PICMG 1 0 format processor board for high performance industrial computers The board is based on Intel Pentium M processor in the uFCPGA478 or uFCBGA478 packages operating at frequencies of up to 2 0 GHz anda Processor Side Bus PSB running at 400 or 533 MHz The Intel Pentium M processor core with integrated 64 KB L1 and up to 2048 KB L2 cache provides its unique performance to power consumption ratio The CPC1100 chipset comprising 82915GM GMCH and ICH6 ICH6M option provides a number of integrated modern communication and storage interfaces thus eliminating the need for additional external controllers The chipset also incorporates dual channel DDR2 memory interface The board can bear up to 2 GB of PC4200 memory installed in two DDR2 240 contact DIMM sockets The board has wide range of interfaces for peripheral devices eight USB 2 0 two RS232 optoisolated RS485 LPT and PS 2 and standard video audio interfaces
47. he CPC1100 board is based on the Intel Pentium M processor in the uFCPGA478 or uFCBGA478 packages operating at frequencies of up to 2 GHz Intel Pentium M processor combines high performance and low power consumption lts enhanced performance characteristics are provided by a newly designed processor core with an integrated 64 KB L1 32 KB instruction cache and 32 KB write back data cache and 2048 KB L2 cache The Intel Pentium M processor supports the Intel SpeedStep enhanced technology to control power consumption and processor die temperature by switching the processor core voltage and frequency between several modes without resetting the system Important performance features of the Intel Pentium M processor also include Si Intel Architecture with Dynamic Execution Data Prefetch Logic L2 cache memory with Advanced Transfer Cache Architecture Streaming SIMD extensions 2 SSE2 400 533 MHz source synchronous FSB n Support for MMXTM technology and Internet Streaming SIMD instructions The Ultra Low Voltage Pentium M processor is optional 2 1 2 System Memory The board bears two 240 pin memory slots Total capacity of the installed DDR2 SDRAM modules can be up to 2 GB The installed memory is PC4200 compliant and supports PC SPD Serial Presence Detect Specification 2 1 3 Chipset The CPC1100 chipset consists of the following devices Mm 82915GM Graphics and Memory Controller Hub GMCH with Accelerated Hub Arc
48. hitecture AHA bus a ICH6 I O Controller Hub with AHA bus ICH6M optionally One 8 Mbit Firmware Hub FWH CPC1100 User Manual 2 1 2007 Fastwel Ver 001 E Detailed Description Fastwel TS CPC1100 The GMCH provides interface for the microprocessor the memory bus the PCI Express x16 in the case of an external graphics controller and includes a high performance graphics accelerator In the current version of the board the support of an external graphics controller is not realized The ICH is a centralized controller for I O peripherals of the board such as the PCI PCI Express USB 2 0 EIDE SATA and AC97 interface The Firmware Hub FWH with capacity of 1 MB is used as the non volatile storage for BIOS North Bridge The 915GM Graphics and Memory Controller Hub GMCH in the 1257uFCBGA package provides interfaces with the central processor with the dual channel DDR2 SDRAM system memory and interface to high performance internal graphics or PCI Express x16 interface not supported by CPC1100 for an external VGA controller It also provides a DMI interface to the ICH The 915GM is optimized for the Intel Pentium M family of microprocessors The chipset supports a PSB frequency of 400 533 MHz with AGTL signaling For single processor systems the single ended AGTL termination is supported It also supports 32 bit addressing for using up to 4 GB memory address space The 915GM includes a system memory controller with a 64 bit
49. igh Frequency Mode to Low Frequency Mode without resetting the system For example the processor operating at 1 6 GHz and 1 484 V HFM can be switched down to 600 MHz and 0 956 V LFM thus reducing the processor power consumption in approx 4 times 3 Thermtrip function is always on to protect the processor in any event In case of a serious cooling subsystem failure the processor will automatically shut down when the die temperature has reached approximately 125 C Once Thermtrip is activated the system does not return to the normal operation mode automatically it is necessary to reset the BIOS settings and to cold restart the system The BIOS settings can be reset by lifting the contact plate of the battery holder for a period of more than 5 seconds 4 External thermal monitor LM87 gathers information about the processor and board surface temperatures from two sensors This information may then be requested by a program to undertake the appropriate actions CPC1100 User Manual 6 1 2007 Fastwel Ver 001 E Thermal and Power Issues Fastwel ZE CPC1100 Recommendations Generally there is no need to enable the Thermal Management functions if the module is operated in an optimally designed environment with sufficient air flow However to guarantee a stable system in unsteady environment both the internal and the external thermal monitors should be enabled These two monitors protect the processor and the whole system against ove
50. is requirement could be harmful for your life or health and can damage the module or entire system ESD Sensitive Equipment This product comprises electrostatically sensitive components Please follow the ESD safety instructions to ensure module s operability and reliability n Use grounding equipment if working at an anti static workbench Otherwise discharge yourself and the tools in use before touching the sensitive equipment E Try to avoid touching contacts leads and components Extra caution should be taken in cold and dry weather CPC1100 User Manual 3 1 2007 Fastwel Ver 001 E Installation Fastwel ZE CPC1100 3 2 Installation Procedure To install CPC1100 in a system follow the instructions below 1 Keep to the safety regulations of the Section 3 1 when performing the following operations A 2 Ensure that the module configuration corresponds to the application requirements before installing For information regarding the configuration of the CPC1100 refer to Chapter 4 For the installation of CPC1100 specific peripheral devices expansion modules and I O devices refer to the appropriate sections in Chapter 3 3 To install the CPC1100 Warning Failure to accomplish the following instruction may damage the module or result in incorrect system operation 1 Make sure that no power is connected to the system 2 Avoiding contact with other modules of the system carefully insert the module
51. mal and Power Issues 6 1 Temperature Control Intensive operation of Intel Pentium M processor in harsh environment requires a special technology to keep the processors die temperature within allowed limits The following sections provide system integrators with the information which will help to meet thermal requirements when developing systems based on CPC1100 6 1 1 Passive Regulation The thermal management concept of CPC1100 module includes four separate but correlated functions Their main purpose is to protect the processor from overheating and reduce its power consumption Dedicated thermal control subsystem allows the processor to operate within safe temperature range without the need for special software or interrupt handling The four thermal protection functions provided by the processor are 1 Thermal Throttling The Pentium M internal thermal monitor controls the temperature of the processor The internal temperature sensor is located near the hottest area of the processor die Each processor is individually adjusted at the factory to compensate the potential manufacturing variations of its characteristics To reduce the processor power dissipation the internal thermal monitor switches the processor core clock on and off with a duty cycle factor of 50 2 The Intel Pentium M processor supports the Intel SpeedStep enhanced technology It allows to switch the processor core voltage and frequency between several modes from H
52. n between control software and BMC similar to a keyboard controller interface BT interface Block Transfer interface Block transfer interface for communication between control software and BMC DDR SDRAM Double Data Rate Synchronous Dynamic Random Access Memory SODIMM Small Outline Dual In Line Memory Module ECC Error Correction Code Data error correction technology used in memory modules FWH Firmware Hub Nonvolatile memory chip part of Intel chipset used for main and reserve BIOS copies in CPC1100 GMCH Graphics and Memory Controller Hub USB Universal Serial Bus LPC Low Pin Count External devices communication interface SMB System Management Bus UART Universal Asynchronous Receiver Transmitter UHCI Universal Host Controller Interface USB Host Controller Interface EHCI Enhanced Host Controller Interface Universal Serial Bus specification UTP Unshielded Twisted Pair CRT display Cathode Ray Tube Display PMC PCI Peripheral Component Interconnect Mezzanine Card CMC Common Mezzanine Card LVDS Low Voltage Differential Signal Digital monitors communication specification RTC Real Time Clock BIOS Basic Input Output System PC Personal Computer PICMG PCI Industrial Computer Manufacturers Group AHA Accelerated Hub Architecture GMCH and ICH communication bus specification CPC1100 User Manual B 1 2007 Fastwel Ver 001 E EIDE Directly processor controlled data exchange AGP Accelerated Gra
53. nnnnnnnnannnnn nenn 6 1 6 1 Temperature Control 6 1 6 1 1 Passive Regulation lobo AA LL Riise 6 1 6 1 2 ee En TEE 6 2 62 SYSIEMIPOWEr EE 6 3 A Supplementary Information usnsra00nnnnannnnnnnnnannnnnnnnnnnnnnnnnnnnnannnnnannnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nenn A 1 A 1 Related Standards and Specifications nono n arce A 1 B Useful Abbreviations Acronyms and Short CUtS rrrii iii B 1 CPC1100 User Manual 0 2 2007 Fastwel Ver 001 E Fastwel LE CPC1100 List of Tables Table 2 1 Table 2 2 Table 2 3 Table 2 4 Table 2 5 Table 2 6 Table 2 7 Table 2 8 Table 2 9 Table 2 10 Table 2 11 Table 2 12 Table 2 13 Table 2 14 Table 2 15 Table 2 16 Table 2 17 Table 2 18 Table 2 18 Table 2 19 Table 2 20 Table 2 21 Table 4 1 Table 4 2 Table 4 3 Table 4 4 Table 6 1 Table 6 2 Table A 1 Table A 2 SMBUS DEVICES ox lilla earn 2 4 PCI Express Bus Connector Pinout eege geed RR eee 2 5 PCI Bus Connector PINOUt nro canon nn nn nn RR RR nn RR RR RnnN RR RRnnN nr nnnnnnrnnnnnrrnnannnenenns 2 6 ISA Bus Connector PINOUT ccenn Sagem 2 7 RS232 Connector J22 J23 Pinout i 2 8 RS485 Connector J24 J38 Pinout ii 2 8 Front Panel USB Connectors PiNOUtS ninri ariana a ai ai 2 9 Onboard USB Connectors Pinolts iaiireal sea 2 9 Supported Display Modes i 2
54. nst another rigid object Also be careful not to drop the product since this may cause damage to the heatsink CPU or other sensitive components as well Please keep in mind that any physical damage to this product is not covered under warranty Note This product is guaranteed to operate within the published temperature ranges and relevant conditions However prolonged operation near the maximum temperature is not recommended by Fastwel or by electronic chip manufacturers due to thermal stress related failure mechanisms These mechanisms are common to all silicon devices they can reduce the MTBF of the product by increasing the failure probability Prolonged operation at the lower limits of the temperature ranges has no limitations Caution Electric Shock Before installing this product into a system and before installing other devices on it always ensure that your mains power is switched off Always disconnect external power supply cables during all handling and maintenance operations with this module to avoid serious danger of electrical shock CPC1100 User Manual 0 5 2007 Fastwel Ver 001 E Fastwel LE CPC1100 Unpacking Inspection and Handling Please read the manual carefully before unpacking the module or mounting the device into your system Keep in mind the following ESD Sensitive Device A Electronic modules and their components are sensitive to static electricity Even a non perceptible by human
55. nterrupt Controller Processor I F 170h 177h IDE Controller SATA Controller or PCI IDE Controller SATA Controller or PCI Forwarded to IDE or SATA 1FOh 1F7h IDE Controller SATA Controller or PCI 2 IDE Controller SATA Controller or PCI Forwarded to IDE or SATA 376h IDE Controller SATA Controller or PCI IDE Controller SATA Controller or PCI Forwarded to IDE or SATA 3F6h IDE Controller SATA Controller or PCI 2 IDE Controller SATA Controller or PCI Forwarded IDE or SATA 4D0h 4D1h Interrupt Controller Interrupt Controller Interrupt CF9h Reset Generator Reset Generator Processor I F Notes 1 A read to this address will subtractively go to PCI where it will master abort 2 Only if IDE I O space is enabled D31 F 1 40 bit 15 and the IDE controller is in legacy mode Otherwise the target is PCI CPC1100 User Manual 2007 Fastwel Ver 001 E Chapter 5 Phoenix BIOS Setup Phoenix BIOS Setup Fastwel ZE CPC1100 5 Phoenix BIOS Setup The Phoenix BIOS in your SBC is an adapted version of a standard BIOS for IBM PC AT compatible personal computers equipped with Intel x86 and compatible processors The BIOS provides low level support for the central processing memory and I O system units With the help of BIOS Setup program you can modify the BIOS configuration parameters and control the special features of your module The Setup program is started by pressing the F2 key and offers a convenient menu interfac
56. ntroller ACPI 2 0 compliant power management logic Enhanced DMA controller High precision event timers Interrupt controller System Management Bus Low Pin Count LPC interface Firmware Hub FWH interface support via LPC bus 1 4 2 Interfaces PCI Express Interface Fully compliant with PCI Express 1 0a specification Four PCI Express root ports shared with Gigabit Ethernet ports Statically configured as four x1 lanes or one x4 lane Up to 2 5 Gb s bandwidth in each direction per x1 lane Two virtual channel support for full isochronous data transfers E Card edge connector PCI Bus Interface Compliant with 2 3 Specification at 33 MHz System master operation Support for 32 bit addressing on PCI using DAC protocol Four available PCI REQ GNT pairs 5 0V compatible Card edge connector Mini PCI Interface Compliant with Mini PCI Specification rev 1 0 n Type IIIB modules support P Onboard connector ISA Bus Interface Compliant with PICMG rev 1 0 Specification Available via LPC ISA bridge or PCI ISA bridge n 16 bit interface n Card edge connector Serial Ports Two software switchable ports COM1 and COM2 n RS 232 through two 10 pin IDC connectors on board E Isolated RS 485 via two 10 pin IDC connectors on board n 16C550 compatible UARTs USB Interface Up to eight USB 2 0 ports supporting UHCI and EHCI a Two USB type A sockets at the board slot bracket n Six USB 2 0 channels via three 10 pin IDC connectors on
57. nty is at its option to replace or repair any defective component part of such products free of charge Fastwel neither assumes nor authorizes any other liability in connection with the sale installation or use of its products Fastwel shall have no liability for direct or consequential damages of any kind arising out of sale delay in delivery installation or use of its products If a product should fail through Fastwel s fault during the warranty period it will be repaired free of charge For out of warranty repairs the customer will be invoiced for repair charges at current standard labor and materials rates Warranty period for Fastwel products is 36 months since the date of purchase The warranty set forth above does not extend to and shall not apply to 1 Products including software which have been repaired or altered by other than Fastwel personnel unless Buyer has properly altered or repaired the products in accordance with procedures previously approved in writing by Fastwel 2 Products which have been subject to power supply reversal misuse neglect accident or improper installation Returning a product for repair 1 Apply to Fastwel company or to any of the Fastwel s official representatives for the Product Return Authorization 2 Attach a failure inspection report with a product to be returned in the form accepted by customer with a description of the failure circumstances and symptoms 3 Carefully packa
58. nux operating systems CPC1100 User Manual 1 1 2007 Fastwel Ver 001 E Introduction Fastwel Ee CPC1100 Some of the CPC1100 s outstanding features are Intel Pentium M processor family up to 2 0 GHz Up to 2 MB L2 on die cache running at CPU speed 82915GM GMCH and ICH6 ICH6M chipset 400 533 MHz processor system bus Up to 2 GB dual channel of DDR2 SDRAM memory running at 533 MHz Integrated 3D high performance VGA controller 64 MB memory shared with system n CRT displays support with resolutions of up to 2048 x 1536 pixels at 16 bits and 75 Hz Two Gigabit Ethernet interfaces one Gigabit and one Fast Ethernet optionally via PCI Express bus 10Base T 100Base TX and 1000Base T EIDE Ultra ATA 100 interface Up to four SATA ports Onboard CompactFlash Type I II socket Two serial ports RS232 RS485 optoisolated software switchable Up to eight USB 2 0 ports PS 2 keyboard and mouse interface Floppy disk interface Parallel port AC97 compatible audio codec with line input output and microphone interfaces Mini PCI interface PCI bus 32 bit 33 MHz ISA bus 16 bit Optional PCI Express up to four x1 or one x4 Hardware Monitor LM87 Additional counters and timers integrated in the ICH Real time clock with battery backup Phoenix BIOS PICMG 1 0 specification compliant ATX power supply support with 20 pin connector Passive or active heatsink solution Available via
59. p 3 PCIE_B29 PWRGD_S3 PCIE_A15 HSIp 1 PCIE_A30 12V PCIE_B15 HSIn 3 PCIE_B30 12V CPC1100 User Manual 2 5 2007 Fastwel Ver 001 E Detailed Description Fastwel TL CPC1100 2 3 1 2 PCI Edge Connector PCI Bus Interface of CPC1100 complies with requirements of PCI Rev 2 3 Specification and operates at 33 MHz It delivers seven PCI REQ GNT pairs and provides support for 64 bit addressing on PCI using DAC protocol Figure 2 2 Table 2 3 PCI Edge Connector LL NK A62 AI CPC1100 is equipped with 124 contact PCI edge connector Its pinout is presented below PCI Bus Connector Pinout PCI_A1 TRST PCI_A32 AD16 PCI_BI 12V PCI_B32 AD17 PCI_A2 12V PCI_A33 3 3V PCI_B2 TCK PCI_B33 C_BE2 PCI_A3 TMS PCI_A34 FRAME PCI_B3 GND PCI B34 GND PCI_A4 TDI PCI A835 GND PCI_B4 TDO PCI_B35 IRDY PCI_A5 5V PCI_A36 TRDY PCI_B5 AEN PCI_B36 3 3V PCI_A6 INTA PCI_A37 GND PCI_B6 AEN PCI_B37 DEVSEL PCI_A7 INTC PCI_A38 STOP PCI_B7 INTB PCI_B38 GND PCI_A8 5V PCI_A39 3 3V PCI_B8 INTD PCI_B39 LOCK PCI_A9 CLKC PCI_A40 SDONE PCI_B9 REQ3 PCI_B40 PERR PCI_A10 5V_IO PCI_A41 SBO PCILB10 REQ1 PCI_B41 3_3V PCIA11 CLKD PCI_A42 GND PCI_B11 GNT3 PCI_B42 SERR PCLA12 GND PCI_A43 PAR PCI_B12 GND PCI_B43 3 3V PCI_A13 GND P
60. phics Port AGTL Advanced Gunning Transceiver Logic PSB Processor Side Bus signal exchange specification SMBus System Management Bus EEPROM Electrically Erasable Programmable Read Only Memory NAND Flash Not And electronic logic gate Flash memory specification SSD Solid State Disk PLCC Plastic Leaded Chip Carrier RAMDAC Random Access Memory Digital to Analog Converter DAC Digital to Analog Converter DVMT Dynamic Video Memory Technology TIL Transistor Transistor Logic ECP EPP Extended Capabilities Port Enhanced Parallel Port Parallel port specifications FDD Floppy Disk Drive EIDE Enhanced Integrated Drive Electronics Mass storage devices interface DMA Direct Memory Access PIO Programmed Input Output Rear I O Board Rear Input Output Board Auxiliary interface board which is connected to the cPCI backplane rear connectors PWM output Pulse Width Modulation Cooling fan control technique ESD Electrostatically Sensitive Device Electrostatic Discharge ACPI Advanced Configuration and Power Interface POST Power On Self Test cPCI CompactPCl Industrial automation systems standard EOS Electrical Overstress MDI Media Dependent Interface Interface with connection type automatical detection CPC1100 User Manual 2007 Fastwel B 2 Ver 001 E
61. racteristics The expected life of a 190 mAh battery Panasonic BR2032 is about 5 years However this typical value may vary because battery life depends on the operating temperature and the shutdown time of the system in which the battery is installed Note It is recommended to replace the battery after approximately 4 years to be sure it is operational Replacing the battery make sure the polarity is correct up Dispose of used batteries according to the local regulations Important CPC1100 User Manual 3 4 2007 Fastwel Ver 001 E Chapter 4 Configuration Configuration Fastwel Ley CPC1100 4 Configuration 4 1 Clear CMOS Jumper Description If the system does not boot due to for example the wrong BIOS configuration or incorrect password the settings stored in CMOS may be cleared using jumper Clear CMOS J7 Procedure for clearing CMOS settings Switch off the system power Set the Clear CMOS jumper into the closed position Wait for at least 10 seconds CMOS setting are reset to factory defaults Set the Clear CMOS jumper back to the open position Switch the power on Configure the system using the BIOS Setup program gt Di Ze ON gt 4 2 FSB Frequency Selection Switch A group of jumper switches J4 and J5 allows to select the front side bus frequency These jumpers should be set prior to switching the power on Allowed jumper positions are showed below Warning All
62. rheating Note Thermal Management functions should be disabled when performing Benchmarks and performance tests otherwise the results will be incorrect due to the power reduction processes influence 6 1 2 Active Regulation To provide controlled active heat dissipation CPC1100 is equipped with standard heatsinks Together with a system chassis with adjustable forced airflow capability this provides a basis for reliable and steady operation Forced airflow of sufficient volume is vital for high performance processors operating in high temperature environments When developing applications using the CPC1100 the system integrator must take into account the overall system thermal requirements System chassis must satisfy these requirements When performing thermal calculations for certain application the developer must consider the contribution of peripherals to be used with the CPC1100 to the total heat emission These devices must also be capable to operate at the temperatures within the system operating range especially those which are attached directly to the CPC1100 processor module Warning Since Fastwel does not assume responsibility for any damage to the CPC1100 module or other system parts resulting from overheating of the central processor it is important to ensure that the CPC1100 operational environment parameters conform to the thermal requirements described in this Manual CPC1100 User Manual 6 2 2007 Fastw
63. stallation of one MiniPCI it expansion module The pinout of this connector is as Ee shown in the following table Table 2 17 MiniPCI Connector Pinout 1 TIP 43 RSVD2 85 AD 08 2 RING 44 AD 26 86 C BE O 3 8PMJ 3 45 C BE 3 87 AD 07 4 8PMJ 13 46 AD 24 88 3 3V_8 5 8PMJ 6 47 AD 23 89 3 3V_4 6 8PMJ 23 48 IDSEL 90 AD 06 7 8PMJ 7 49 GND_4 91 AD 05 8 8PMJ 43 50 GND_11 92 AD 04 9 8PMJ 8 51 AD 21 93 RSVD3 10 8PMJ 53 52 AD 22 94 AD 02 11 LED1_GRNP 53 AD 19 95 AD 03 12 LED2_YELP 54 AD 20 96 AD 00 13 LED1_GRNN 55 GND_5 97 5V_1 14 LED2_YELN 56 PAR 98 RSVD9_WIP5 15 CHSGND 57 AD 17 99 AD 01 16 RSVD5 58 AD 18 100 RSVD10_WIP5 17 INTB 59 C BE 2 101 GND_9 18 5V_2 60 AD 16 102 GND_15 19 3 3V_1 61 IRDY 103 AC_SYNC 20 INTA 62 GND_12 104 M66EN 21 RSVD1 63 3 3V_3 105 AC_SDATA_IN 22 RSVD6 64 FRAME 106 AC_SDATA_OUT 23 GND_1 65 CLKRUN 107 AC_BIT_CLK 24 3 3VAUX1 66 TRDY 108 AC_CODEC_IDO 25 CLK 67 SERR 109 AC_CODEC_ID1 26 RST 68 STOP 110 AC_RESET 27 GND_2 69 GND_6 111 MOD_AUDIO_MON 28 3 3V_5 70 3 3V_7 112 RSVD8 29 REQ 71 PERR 113 AUDIO_GND1 30 GNT 72 DEVSEL 114 GND_16 31 3 3V_2 73 C BE 1 115 SYS_AUDIO_OUT 32 GND_10 74 GND_13 116 SYS_AUDIO_IN 33 AD 31 75 AD 14 117 SYS_AUDIO_OUT_GND 34 PME 76 AD 15 118 SYS
64. t 18 HD15 HD data 15 In Out 19 GND Ground signal 20 NC 21 IDEDRQ DMA request In 22 GND Ground signal 23 IOW I O write Out 24 GND Ground signal 25 IOR I O read Out 26 GND Ground signal 27 IOCHRDY I O channel ready In 28 GND Ground signal 29 IDEDACK DMA Ack Out 30 GND Ground signal 31 IDEIRQ Interrupt request In 32 NC 7 33 AI Address 1 Out 34 NC 35 AO Address O Out 36 A2 Address 2 Out 37 HCSO HD select 0 Out 38 HCS1 HD select 1 Out 39 NC 40 GND Ground signal Note ATA 66 and ATA 100 work at higher frequencies and require a specialized cable which has additional grounding wires to reduce reflections noise and inductive effects This cable also supports all legacy IDE drives The blue end of the ATA 100 cable must be connected to the main board the gray connector to the UltraDMA 100 slave device and the black connector to the UltraDMA 100 master device CPC1100 User Manual 2 13 2007 Fastwel Ver 001 E Detailed Description Fastwel TS CPC1100 2 3 6 1 HDD LED Connector Figure 2 7 HDD LED Connector The onboard HDD LED connector J8 is used to control an 4 external HDD activity LED indicator It is lit when any of IDE or SATA channel is active the data are read or written from to an external disk drive Contact 1 should be connected to 2 3 7 Serial ATA Ports Figure 2 8 Serial ATA Connector r CPC1100 has two ICH6M or four ICH6 s
65. tandard SerialATA ly connectors installed on board SerialATA drives can be attached to 7 4 J18 J19 J36 and J37 J18 and J19 for ICH6M connectors The connector s pinout is presented in the table below Table 2 13 SATA Connector Pinout 1 GND TXP TXN GND RXN RXP GND N O O A O0O NnN It is recommended to use a 45 cm cable for connection of SATA drives CPC1100 User Manual 2 14 2007 Fastwel Ver 001 E Detailed Description Fastwel TS CPC1100 2 3 8 CompactFlash Socket To enable usage of CF memory cards CPC1100 has a CompactFlash Type I II socket located on the bottom side of the board CF removable mass storage devices are fully compatible with 16 bit ATA ATAPI 4 IDE interface with DMA support CF Specification v 4 1 CompactFlash socket is connected to the EIDE port as master at the current version of CPC1100 Table 2 14 CompactFlash Socket Pinout 1 GND Ground signal 2 D03 Data 3 In Out 3 D04 Data 4 In Out 4 D05 Data 5 In Out 5 D06 Data 6 In Out 6 D07 Data 7 In Out 7 IDE_CSO Chip select 0 Out 8 GND A10 9 GND ATASEL 10 GND A09 11 GND A08 12 GND A07 13 3 3V 3 3 V power 14 GND A06 15 GND A05 16 GND A04 17 GND A03 18 A02 Address 2 Out 19 A01 Address 1
Download Pdf Manuals
Related Search
Related Contents
Vigitron VI0021 Gemini TT-01mkii Turntable User Manual BoConcept Model 3610 Assembly Instruction HP 8900B User's Manual NG-283 SPEEDY - Galico QT-9 instructionsrev9_FCC 医療法第 25条第 1項の規定 に基づく立入検査要綱 User Manual DVC-200 – Bedienungsanleitung Copyright © All rights reserved.
Failed to retrieve file