User manual 738113
Contents
1. 55L and 55R with the inputs 55L 4 and 55R 5 on the adaptive headlight module 4 Connect the Auxiliary headlamps 738 18 to the adaptive headlight module s outputs 55L 9 and 55R 8 5 If available Connect the DRL in Headlights 738 166 and 738 167 to the DRL outputs 10 amp 11 6 If no Instrument cluster unit 739 6027 is available Plug the speed simulator Simulation ABS Ti 579 163 into Slot 14 and link its output with input V 3 7 For a clear display of the speed you may use the Tachometer speedometer digital 739 6023 Intelligent lighting 4 2 Functional Test The system requires 12 VDC for operation Switch the ignition T15 on and then the cornering light T56b Activate the left or right turn signal the respective fog lamp must light up 4 3 Operation If the ignition and the light are on and the programming mode has not deactivated the adaptive headlight module a fog lamp turns on if a ata standstill the turn signal is on or at V lt Vmax a steering wheel angle gt 90 is detected To calibrate the steering wheel angle to 0 carry out programming 5 After passing the speed threshold the fog lamp turns back off after the set persistence In the case of errors Ground interruption Power supply interruption and T15 interruption the MODE LED blinks red Note The speed signal can connect directly to input V 3 with 1 Hz 1 km h as a PWM signal or i2. parameter as necessary Press once The adaptive headlight module is activated Press twice The adaptive headlight module is deactivated Press 3 times You can now change the speed at which the fog lamp turns back off after going around a corner per ECE 119 at 40 km h Default 20 km h Setting range 20 60 km h Set the desired speed on the vehicle Then start the programming and the new value is then stored as the set speed Press 4 times You can now set the persistence Default 4s Setting range 1 10s This defines the new length of time the button remains pressed at the fourth pressure Press it only briefly and this automatically sets a value of 1 second hold it longer than 10 seconds and this programs a value of 10 seconds Press 5 times This serves to determine the steering wheel s straight forward position The MODE LED lights up orange until you bring the steering angle sensor to the center position straight ahead 0 Note The values above are not permanently stored Press 6 times You can now set the behavior of the DRL when the cornering light turns on Behavior according to ECE R87 the DRL switches off if the cornering light is on Behavior according to ECE R7 the DRL dims if the cornering light is on The sixth pressure on the button toggles between the two behaviors Note This setting is permanently stored
3. PHYSIK CHEMIE BIOLOGIE TECHNIK 10 14 W2010 Wei 2 3 5 a TAa J850 e2 E bodo 15 NL NL TFL TFL z 89 10 f1 a 13 1 LEYBOLD EEA 1 Description This Cornering light serves the classroom retrofitting of the automotive educational system CAN bus lighting management system 738 111 to add cornering light functionality It also offers connection options for two LED daytime running lights e g in connection with the Head lights 738 166 and 738 167 Safety notes LI Lb DIDActTic Instruction Manual 738 113 Cornering Light 2 T30 connection Low speed CAN bus SDVC connection Right fog lamp input Left fog lamp input T15 connection High speed CAN bus Right fog lamp output Left fog lamp output Right LED DRL output Left LED DRL output Programming key Indicator LED Plug for Simulation ABS Ti 579 163 T31 ground connection Scope of Supply Cornering light module 3 Technical Data High speed CAN bus 500 kBps Low speed CAN bus 100 kBps Current carrying capacity FL Ima 4 5 A Current carrying capacity DRL Imax 150 mA Supply voltage Ug 12 15 V Instruction Manual Page 2 3 4 Startup 4 1 Setup 1 Connect the device to the management system 738 111 2 Link the connections for T30 1 T15 6 ground 15 low speed CAN bus 2 and high speed CAN bus 7 3 Link the outputs for the Electrical system control unit 738 111 01 for the fog lamps
4. s readable by the Instrument cluster unit 739 6021 as a CAN bus communication If both signals are available in parallel the CAN bus signal takes precedence 4 4 Programming Reprogramming the cornering light module is possible without a PC To initiate the programming mode press and hold the T button 12 for approx 2 seconds until the MODE LED 13 blinks green You can then press the T button again once or several times within the next second to select the programming function Module off Module on Speed threshold Persistence Steering angle sensor calibration DRL function If after the programming mode s initiation you do not press the button again the system automatically leaves this mode within 3 seconds After the function s selection and programming the adaptive headlight module confirms the adoption of the new values by illuminating the left and right fog lamps LD DIDACTIC GMBH Leyboldstrasse 1 D 50354 Huerth Germany Phone 49 0 2233 604 0 Fax 49 0 2233 604 222 e mail info Id didactic de by LD Didactic GmbH Printed in the Federal Republic of Germany Technical alterations reserved Page 3 3 Instruction Manual In the programming mode press the button only as often as listed below to reprogram the corresponding function and wait until the auxiliary headlamps finally confirm the adoption of the new values by illuminating alternately Only then can you change another
Download Pdf Manuals
Related Search