5DT HMD 800 Series User's Manual - playking.de
Contents
1. Do not wear the product for longer than one hour at a time When this period has expired take a break for at least 10 15 minutes before wearing the device again A warning to stop using the device will appear in the displays after two hours 3 4 Electrical Safety e Make sure that the line voltage of the power adapter AC adapter is the same as the line voltage of the country where the HMD will be used For example if the line voltage of the power adapter is 100 120V AC it should not be used in a country where the line voltage is 220 240V Using an incorrect power adaptor may cause it to explode e Unplug the power adapter when the unit is not in use e Always use the designated AC power adapter included with the product e To prevent electric shock and or fire do not unplug by pulling on the cord and do not touch the power plug with bare hands 3 5 3 6 Do not use the product in a wet environment such as a bathroom Cleaning the Product Always unplug the power adapter before cleaning the product to prevent electric shock and or fire Remove dust on the headset by using a soft cloth To remove stains or dirt wipe the HMD with a soft cloth dampened with a neutral detergent Do not use solvents like paint thinner benzene or other products that may damage the surface of the product Personal Hygiene Alcohol wipes are useful for cleaning the HMD between users for multiple user applications Alcohol will remove sk2. b Select PC STABLE to adjust the vertical timing of the image Press Sel to change the PC STABLE value CONTROL 4 gt PC STABLE PC ADJUST COLOR STD RESET Figure 37 Use PC STABLE to adjust for instability in the vertical image position c Use the Up and Down butions to stabilize the image Press Sel to accept the new value CONTROL PC STABLE pt 4 Figure 38 Adjust the value using the Up and Down buttons d To exit the menu screen press the Menu button until the menu disappears 25 6 14 Color Standard The color standard can be alternated between PAL and NTSC a Press the Menu button Select the CONTROL menu using the Up and Down buttons Press Sel to enter the control menu b Select COLOR STD to adjust the color standard of the image Press Sel to change the COLOR STD value CONTROL 4 PC STABLE PC ADJUST gt COLOR STD RESET Figure 39 Use COLOR STD to select the color standard c Use the Up and Down buttons to alternate between NISC and PAL color standards Press Sel to accept the new value CONTROL CONTROL COLOR STD COLOR STD gt NISC M gt PAL BGHI Figure 40 Alternate between NTSC and PAL using the Up and Down buttons d To exit the menu screen press the Menu button until the menu disappears 26 7 About 5DT ODT lt Fifth Dimension Technologies gt is a high technology company specializing in Virtual Reality VR SDT develops prod
3. Can you reproduce the problem easily Describe how f Actions taken by yourself to solve the problem You may also contact 5DT directly at support 5DT com 31 Appendix B Specifications we a SDT HMD 800 Stereo ANinput ANinput Stereo Mini Jack Approx 4W 5DT HMD 800 a a a SDT HMD 800 Stereo Operating Temperature Range Temperature Range 10 50 C Dimensions 300 mm L x 200 mm W x 240 mm H Weight 594 arams without controlbox Connectors PC Input PC Input D sub 15 pin 32 Appendix C Product Warranty Thirty 30 Day Customer Satisfaction Guarantee If for any reason you are disappointed with this product please contact your supplier If you are not completely satisfied you will be granted a 100 refund once the product is returned undamaged less a 15 restocking fee Unfortunately shipping costs cannot be refunded One 1 Year Product Warranty SDT warrants to the original purchaser of the 5DT HMD 800 or 5DT HMD 800 Stereo that it will be free of defects in materials and workmanship for a period of one year from the original date of purchase During the warranty period SDT will at their discretion repair or replace with a reconditioned unit components that are defective Exclusions The above warranty is provided for private use only and shall not apply to any commercial use of the product including but not limited to e Location Based Entertainment LBE applications e Trade show demo
4. follow the instructions for adjusting screen flicker with the 5DT HMD 800 but take note that the right screen flicker will need to be adjusted with the right control box and the left screen flicker with the left control Dox 3 Safety First Please take CAREFUL NOTE of the following SAFETY ISSUES Due to medical safety reasons this product should not be used by the following persons 3 1 Individuals with Epilepsy Individuals who have been diagnosed with Epilepsy or who have a personal or family history of Epilepsy should not use this product because it may trigger epileptic seizures If you have any doubts about this consult with a medical doctor and or neurologist before using the product 3 2 Individuals Younger than 10 Years of Age The eyes of a person younger than 10 years of age are still developing the ability to focus Therefore individuals younger than 10 years of age should not use this product because it may adversely affect the focusing ability of their eyes 3 3 Termination of Usage STOP using this product IMMEDIATELY if e You experience discomfort of any nature e You develop a headache e You start feeling nauseous e You start experiencing vertigo dizziness Take special care to adjust the Interpupillary Distance IPD distance between the displays An incorrect IPD will result in a fuzzy unfocused image Your eyes will strain to correct the fuzzy unfocused image and this will normally cause a headache
5. up lf the picture is fuzzy or unfocused adjust the IPD Interpupillary Distance Dial on the inside of the headset until the picture is clear Figure 11 You may need to alternately close your left and right eye to ensure that the respective display is in the middle of the respective eye s vision Figure 11 The Interpupillary Distance IPD Dial 6 3 Basic Controls Navigating Menus You can control the 5DT HMD 800 by using the Up Down Menu and Sel buttons mr Ss 3 oe GO TSEN DOWN AAE AE Fa O O POWER ON DOWN UP SEL MENU ON OFF Y VOL Figure 13 Menu Navigation Buttons for the 5DT HMD 800 Stereo a The menu can be activated by pressing the Menu button INPUT MENU gt VIDEO MODE S VHS MODE PC MODE CONTROL Figure 14 Press the Menu Button for the input menu of the 5DT HMD 800 MAIN MENU gt VIDEO MODE PC MODE 3D OFF CONTROL Figure 15 Press the Menu Button for the main menu of the 5DT HMD 800 Stereo b Use the Up and Down buttons to navigate up and down or left and right through the menus CONTROL gt BRIGHT Scroll down CONTRAST or up to see SOUND xs more selections MONO Figure 16 Scroll Up and Down c Press the Sel button to select a chosen setting d To exit the menu screen press the Menu button until the menu screen disappears 14 6 4 Changing the Display Mode You can select the video input of your c
6. video input Left LCD Right LCD Left video Right video Separate Video g Right video input Figure 21 Separated Input 3D Mode 17 6 6 Changing 3D Modes a Turn on the 5DT HMD 800 Stereo b Use the Up and Down buttons to move to 3D OFF and press Sel c Press Sel to toggle between the different 3D modes See Figure 22 First state __ 0 _ PCLINE __ PCFIELD interlace ield sequenti er VIDEO SEPA lt VIDEO FIELD PC SEPA separation 6 field sequential J separation Figure 22 Press Sel to change between the different 3D modes d After selecting the appropriate 3D mode choose PC MODE or VIDEO MODE and press Sel The left and right display signals can be swapped by pressing the Sel button without the menu being active 6 7 Changing Brightness and Contrast a Press the Menu Button b Select CONTROL using the Up and Down buttons c Press Sel to enter the CONTROL menu INPUT MENU VIDEO MODE MAIN MENU VIDEO MODE S VHS MODE PC MODE PC MODE gt CONTROL 3D OFF gt CONTROL Figure 23 Select the CONTROL Menu for the 5DT HMD 800 Left and 50T HMD 800 Stereo Right d Select BRIGHT to adjust the brightness or CONTRAST to change the display contrast Press Sel to select one of the options CONTROL 4 CONTROL 4 gt BRIGHT gt BRIGHT CONTRAST CONTRAST SOUND MUTE MONO Figure 24 Select BRIGHT or CONTRAST for the 5DT HMD 800 Left an
7. 5DT HMD 800 Series User s Manual 5DT Fifth Dimension Technologies www 5DT com IDT HMD 800 Head Mounted Display 5DT HMD 800 Stereo Stereo Head Mounted Display User s Manual All rights reserved No part of this manual software or hardware may be copied reproduced translated or reduced to any electronic medium or machine readable format without the written consent of 5DT lt Fifth Dimension Technologies gt All trademarks and trade names are the respective property of their owners Unless otherwise indicated the term 5DT HMD 800 in this manual refers to both the standard and the stereo HMD The stereo HMD will be indicated as 5DT HMD 800 Stereo where there are differences between the two devices Version 2 00 January 2002 Table of Contents 1 INTRODUCTION 2 STEREO MODELS 3 SAFETY FIRST 3 1 3 2 3 3 3 4 3 5 3 6 4 1 4 2 Individuals with Epilepsy Individuals Younger than 10 Years of Age Termination of Usage Electrical Safety Cleaning the Product Personal Hygiene PACKAGE CONTENTS Parts 5DT HMD 800 Parts 5DT HMD 800 Stereo 5 CONNECTING THE HMD 5 1 5 2 5 3 5 4 6 1 6 2 6 3 6 4 Connecting Electric Power Connecting your HMD to a PC Connecting your 5DT HMD 800 to a Video Source Connecting your 5DT HMD 800 Stereo to a Video Source USING YOUR HMD Basic Use Donning the Headset Basic Controls Basic Controls Navigating Menus Changing the Dis
8. Connect the supplied D sub SVGA cable to the SDT HMD 800 control box and to the output of your video card as in Figure 6 b Attach the Audio connection as in Figure 6 Figure 6 Connecting the 5DT HMD 800 Stereo to a PC 5 3 Connecting your 5DT HMD 800 to a Video Source The 5DT HMD 800 can be connected to VCRs DVD Players Camcorders Game Consoles or any other external video source The video adapters can be connected using either S Video cables RCA cables or SCART cables It is recommended that the S video connection be used for optimal video image quality To connect using S Video Connect the supplied S Video cable to the video output source and the 5DT HMD 800 according to Figure 7 To connect using RCA Connect the supplied audio and video cable according to the shape and color of the video audio output terminal of the external source See Figure 7 a P gt cA s Figure 7 Connecting the 5DT HMD 800 to an S Video or RCA source To connect using SCART a Connect the SCART jack to the output terminal of the source as in Figure 8 b Connect the yellow video cable to the video input terminal of the 5DT HMD 800 c Connect the black audio cable to the audio input terminal of the 5DT HMD 800 Figure 8 Connecting the 5DT HMD 800 to an S Video or SCART source 5 4 Connecting your 5DT HMD 800 Stereo to a Video Source The 5DT HMD 800 Stereo can be connected to VCRs DVD Players Camcorders Game
9. Consoles or any other external video source that can be connected using RCA cables Connect the supplied audio and video cable according to the shape and color of the video audio output terminal of the external source See Figure 9 oe F 5 a ra T pa E a a wil Figure 9 Connecting the 5DT HMD 800 Stereo to a video source 10 6 6 1 Using your HMD Basic Use Donning the Headset Warning If the headset is not adjusted properly it can lead to fatigue of the eyes or blurred vision In general the headset should not be worn if the user is experiencing discomfort and should not be worn longer than one hour at a time without taking a break for 10 15 minutes To don the HMD follow these steps a b Place the headset on top of the head and gently slide it down Adjust the top and back ratchets see Figure 10 so that the headset is comfortable and that the displays are as close to the eyes as possible Take care not to tighten the back ratchet too much Adjust the angle of the headset so that the optical display is 5 to 10 degrees below the horizontal Adjust the earphones so that they are in a comfortable position Figure 10 Adjust the headset using the top and back ratchets 6 2 Basic Controls a Turn on the power to the external device and switch on the video signal b Switch on the power button on the control box The power lamp should light
10. adphones Video Modes 5DT HMD 800 e SVGA e Composite Video PAL NTSC e S Video Video Modes 5DT HMD 800 Stereo e SVGA Mono e SVGA Stereo Line Sequential e SVGA Stereo Field Sequential e SVGA Stereo Separate Inputs e Composite Video PAL NTSC 2 Stereo Models Up to January 2002 the 5DT HMD 800 could only be used in Separate Input 3D mode This unit can be identified by its two control boxes The following points apply only to users who have this version e The package of the 5DT HMD 800 should contain the following e 2x SVGA Cables e 2x RCA to RCA Cables e 2x Power Adapters e 2x SCART to RCA Cables e 2x S Video Cables e 1x Audio Cable e The 5DT HMD 800 Stereo is supplied with 2 power supplies and each control box must be connected to a power supply e To connect your 5DT HMD 800 Stereo to a PC follow these steps a Connect the supplied D sub SVGA cable to the 5DT HMD 800 control box and to the output of your video card for the left hand display b Repeat Step a for the right hand display c Attach the Audio connection as in Figure 5 to the left handed display control Dox e Please note that if you are using the 5DT HMD 800 Stereo with a single video output a video splitter is required which can be obtained from 5DT The video splitter will split the video input into 2 or more identical signals that can be separately fed into the HMD s inputs e For the 5DT HMD 800 Stereo
11. d 5DT HMD 800 Stereo Right e Adjust the brightness or contrast using the Up or Down buttons CONTROL BRIGHT ILLY SLE Figure 25 Change the brightness or contrast using the Up and Down buttons f To exit the menu screen press the Menu button until the menu disappears 6 8 Controlling the Audio If you want to adjust the volume level turn the volume dial on the side of the control box for the 5DT HMD 800 or press the Up and Down buttons for the 5DT HMD 800 Stereo Figure 26 Adjust the volume using the volume dial on the 5DT HMD 800 and the Up and Down Buttons on the 5DT HMD 800 Stereo The sound can also be muted or forced to mono mode 5DT HMD 800 only by using the following menus a Press the Menu button Select the CONTROL menu using the Up and Down buttons Press Sel to enter the control menu b For the 5DT HMD 800 press the Up and Down buttons to select the SOUND option to switch the sound on or off mute or select the MONO option to force the sound to mono mode For the 5DT HMD 800 Stereo select MUTE to switch the sound on or off Press Sel to select an option CONTROL 4 CONTROL 4 BRIGHT BRIGHT CONTRAST CONTRAST gt SOUND gt MUTE 2 MONO Figure 27 Select SOUND or MUTE to mute the sound or MONO to force the sound to mono mode c To exit the menu screen press the Menu button until the menu disappears 20 6 9 Adjusting Screen Flicker In the PC mode the pictu
12. d Down buttons d To exit the menu screen press the Menu button until the menu disappears 23 6 12 PC Jitter Adjustment Timing errors often occur in graphics cards which might cause skewing of the image displayed This can be rectified using the PC ADJUST option in the CONTROL menu Figure 34 Timing errors may cause skewing of the image To compensate for this a Press the Menu button Select the CONTROL menu using the Up and Down buttons Press Sel to enter the control menu b Select H POSITION to adjust the horizontal position of the image or V POSITION to adjust the vertical position of the image Press Sel to change the PC ADJUST value a CONTROL PC STABLE gt PC ADJUST COLOR STD RESET Figure 35 Select PC ADJUST to fix skewing of the image c Use the Up and Down buttons to adjust the timing Press Sel to accept the new value CONTROL PC ADJUST PH Ht AT Figure 36 Adjust the PC ADJUST value using the Up and Down buttons d To exit the menu screen press the Menu button until the menu disappears 24 6 13 Vertical Stabilization Adjustment If any instability occurs in the vertical direction of the PC screen it may be stabilized using the PC STABLE option in the CONTROL menu Please note that this option only has an effect in PC MODE a Press the Menu button Select the CONTROL menu using the Up and Down buttons Press Sel to enter the control menu
13. d into the COMMON input port Check that the video mode is set up correctly The video mode should be VGA 60Hz negative sync or VESA standard SVGA 60Hz 72Hz or 75Hz positive sync The 3D does not work in PC FIELD mode e Check that the external source is connected to the COMMON input port e Check that the video source is set up to display in Field Sequential mode One display has no image e In PC 3D SEPA mode the left and right signals must be the same mode The signals must be plugged in and active before changing the mode The picture is dark and fuzzy e Make sure that the external source is connected and is turned on Adjust the brightness of the display e Adjust the Interpupillary Distance IPD dial on your headset e Check that the volume is not set to zero e Check that the control is not muted The color appears incorrect J Check the color control settings Check that the right color standard is being used NTSC or PAL If you experience problems or have complaints suggestions or other comments please feel free to contact your supplier preferably via e mail Please have the following information available or include it in your written correspondence a Computer processor make and model e g Pentium IIl 1GHz b Computer graphics card e g GeForce Ill 30 c Operating system and version e g Windows 2000 d The symptoms of the problem and what was happening when the problem occurred e
14. ge to different displays The even lines are sent to the left display and the odd lines to the right display as in Figure 19 obeu HOT UIT UAF A SS A ae Be SO a a eR a NS Aen BHEW WH suq POO Figure 19 Interlaced 3D Mode Page Flipped 3D Mode Frame Sequential Stereo Page Flipped 3D Mode can be used with both the SVGA and composite video signals You must use the input port marked COMMON for this mode You can use 60Hz 72Hz or 75Hz VESA Standard SVGA for the PC mode and NTSC PAL or SECAM for video sources Page Flipped 3D works by assigning different frames of the image to different displays The even frames are sent to the left display and the odd frames to the right display as in Figure 20 16 Even field Left image Odd field Right image Left LCD Right LCD Left video Right video Input Video Rearranged by control box Figure 20 Page Flipped 3D Mode Separated Input 3D Mode Separated Input 3D Mode is for use with both the SVGA and composite video signals Separated Input 3D mode takes two separate video signals and displays them on the two different LCDs as in Figure 21 You can use 60Hz 72Hz or 75Hz VESA Standard SVGA for the PC mode and NTSC PAL or SECAM for video sources The two separate video signals MUST have the same resolution as well as the same frequency Please connect both SVGA cables before activating the 3D mode Do not disconnect an SVGA cable during operation Left
15. he image Press Sel to change one of the options CONTROL FLICKER R FLICKER L gt H POSITION V POSITION Figure 30 Select H POSITION to adjust the horizontal position of the image or V POSITION to adjust the vertical position of the image c Use the Up and Down buttons to center the image Press Sel to accept the new value CONTROL H POSITION Pt 4 Figure 31 Adjust the position value using the Up and Down buttons d To exit the menu screen press the Menu button until the menu disappears 22 6 11 RGB and Video Color Adjustment If the initial color tone is not optimized the individual Red Blue and Green components can be adjusted as well as the overall color gain in Video mode a Press the Menu button Select the CONTROL menu using the Up and Down buttons Press Sel to enter the control menu b Select R COLOR ADJ to adjust the red component G COLOR ADJ to change the green component or B COLOR ADJ to change the blue component Select V COLOR ADJ to change the color gain in video mode Press Sel to change one of the options CONTROL 4 gt RCOLOR ADJ G COLOR ADJ B COLOR ADJ V COLOR ADJ Figure 32 Change the color intensities from the CONTROL menu c Use the Up and Down buttons to adjust the color values Press Sel to accept the new value CONTROL R COLOR ADJ CONTROL VIDEO COLOR HHHH bH Figure 33 Adjust the color values using the Up an
16. hoice by changing the display mode in the menu in Figure 17 or Figure 18 a Turn on the video source and the SDT HMD 800 b Press the Menu button c Use the Up and Down buttons to the video mode d Press Sel to select a choice In the PC mode the picture might not show if the current input mode is not supported The input mode should be DOS Mode VGA 60Hz SVGA 60Hz SVGA 72Hz or SVGA 75Hz Please note that the 5DT HMD 800 works with VESA standard video signals which may not be supported with some graphics cards If you have any problems with the PC image please refer to the sections on PC Jitter or PC Stabilization INPUT MENU VIDEO MODE S VHS MODE gt PC MODE CONTROL Figure 17 Select the video mode from the Input menu of the 5DT HMD 800 MAIN MENU gt VIDEO MODE PC MODE 3D OFF CONTROL Figure 18 Select the video mode from the Main menu of the 5DT HMD 800 Stereo 6 5 Stereo Modes The 5DT HMD 800 operates in three different stereo modes Interlaced 3D Mode Line Sequential Stereo Page Flipped 3D Mode Frame Sequential Stereo and Separated Input 3D Mode Interlaced 3D Mode Line Sequential Stereo Interlaced 3D Mode is for use with the SVGA video signal You must use the input port marked COMMON for this mode You can use 60Hz 72Hz or 75Hz VESA Standard SVGA for this stereo mode Stereo is currently not supported for VGA mode Interlaced 3D works by assigning different lines of the ima
17. in oil and makeup that has been transferred to the HMD The front back and top foam inserts should also be cleaned or replaced as necessary Soak the foam inserts in a mild detergent rinse lightly and leave in the sun to dry There have been anecdotal reports of lice pest transmission between HMD users in multiple user applications There are sprays available that will kill the lice on furniture and clothing These sprays are hazardous and you need to judge the benefits versus the risks of using these sprays Make sure to switch the HMD off and to cover the optics before wiping it or spraying it 4 Package Contents 4 1 Parts 5DT HMD 800 Please check that your SDT HMD 800 package contains all the necessary cables and accessories as illustrated in Figure 1 It will be difficult to properly install and use the product if any item is missing To connect the HMD to your computer or video output follow the instructions in the Section 5 1 x SVGA Cable 1 x RCA to RCA Cable 1 x Audio Cable 1 x Power Adapter 1 x SCART to RCA Cable 1 x S Video Cable Figure 1 5DT HMD 800 Accessories 4 2 Parts 5DT HMD 800 Stereo Please check to see that your SDT HMD 800 Stereo package contains all the necessary cables and accessories as illustrated in Figure 2 It will be difficult to properly install and use the product if any item is missing To connect the HMD to your computer or video output follow the instructions in Section 5 2
18. ine Inspection Logging System e High Voltage Line Inspection Program e High Voltage Line Inspection Training System e High Voltage Line Repair Training System e High Voltage Yard Training Simulator Industrial e Crane Operator Training Simulator Marine e Marine Technology Demonstrator e Unmanned Underwater Vehicle UUV ROV Training Simulators Medical e Bronchoscope Training Simulator e Exposure Treatment Phobia Simulator e Gastroscope Training Simulator Mining e Continuous Miner Training Simulator Mechanized Coal Mining e Surface Mining Training Simulator Visualization e Flight Visualization System e Flow Visualization System Other e Landscape Generation and Real time Rendering Technology Information on these systems may be supplied on request 28 8 Contact Information US and Americas 5DT Inc 2005 De La Cruz Blvd Suite 292 Santa Clara CA 95050 USA Tel 1 408 748 1316 Fax 1 408 748 1329 e mail info us 5dt com Web www odt com Rest of World 5DT Fifth Dimension Technologies 25 De Havilland Crescent P O Box 5 Persequor Park 0020 Pretoria South Africa Tel 27 12 349 2690 Fax 27 12 349 1404 Email info 5dt com Web www odt com 29 Appendix A Troubleshooting gt There is no video Signal Check that the power adapter is plugged in and the POWER ON OFF lamp is lit Check that the resolution of the input signal is 800x600 Check that the video cable is plugge
19. nstrations This warranty shall not apply to defects resulting from the following e Misuse e Improper or inadequate maintenance e Unauthorized modification Warranty Claim Instructions We will try our best to get your repaired product back to you as soon as possible In order to do this we request your full cooperation with respect to the warranty claim instructions below Please adhere strictly to the following instructions a Contact your supplier to determine if you need to return the product If your supplier is unable to determine this contact SDT directly Do not return a product to your supplier or to SDT without first contacting them b Your supplier or SDT will issue you with a Return Material Authorization RMA number Do not return a product to your supplier or to SDT without an RMA number c Pack the items to be returned securely using the original packaging material if possible d Please enclose the following e Your original sales bill e Name address contact telephone fax numbers e E mail address e Reason for returning the item e RMA number 33 e Mark your shipping container with the RMA number to expedite handling by customs or your supplier at SDT f Ship prepaid to your supplier or to SDT Shipping charges to SDT are your responsibility COD shipments will not be accepted by 5DT g When completing customs or courier documentation please clearly indicate Unit returned for repairs under
20. play Mode A Rh CO WO WO O O 10 11 11 12 13 15 6 5 6 6 6 7 6 8 6 9 6 10 6 11 6 12 6 13 6 14 Stereo Modes Changing 3D Modes Changing Brightness and Contrast Controlling the Audio Adjusting Screen Flicker Horizontal and Vertical Position Adjustment RGB and Video Color Adjustment PC Jitter Adjustment Vertical Stabilization Adjustment Color Standard 7 ABOUT 5DT 8 CONTACT INFORMATION APPENDIX A TROUBLESHOOTING APPENDIX B SPECIFICATIONS APPENDIX C PRODUCT WARRANTY Thirty 30 Day Customer Satisfaction Guarantee One 1 Year Product Warranty Exclusions Warranty Claim Instructions 16 18 19 20 21 22 23 24 25 26 27 29 30 32 33 33 33 33 33 1 Introduction Thank you for choosing this product We trust that you will have a lot of fun and satisfaction using it The 5DT Head Mounted Display HMD 800 offers the user an affordable immersive viewing experience with 1 44 million pixels of resolution This product is particularly useful for research and development virtual reality simulation computer graphics applications 3D CAD systems virtual showrooms and personal entertainment Features e Affordable quality e Adjustable top back ratchets e Mono or stereo models e Cable organizer e Mounting base for head trackers e Crisp SVGA image e Extreme comfort e User configurable immersivity e Lightweight e Flip up mode for reality checks e High quality he
21. re might not show if the current input mode is not supported The input mode should be DOS Mode VGA 60Hz SVGA 60Hz SVGA 72Hz or SVGA 75Hz Please note that the 5DT HMD 800 works with VESA standard video signals which may not be supported with some graphics cards For the 5DT HMD 800 follow these instructions to minimize screen flicker a Press the Menu button Select the CONTROL menu using the Up and Down buttons Press Sel to enter the control menu b Select FLICKER R if the flicker appears on the right screen or FLICKER L if the flicker appears on the left screen CONTROL gt FLICKER R FLICKER L H POSITION V POSITION Figure 28 Select FLICKER R to adjust flicker on the right screen or FLICKER L to adjust flicker on the left screen c Press the Up and Down buttons until the screen flicker disappears Press Sel to accept the new value CONTROL FLICKER R gt i lt Figure 29 Adjust the flicker value using the Up and Down buttons d To exit the menu screen press the Menu button until the menu disappears 21 6 10 Horizontal and Vertical Position Adjustment When the screen is not centered H POSITION and V POSITION can be used to center the picture a Press the Menu button Select the CONTROL menu using the Up and Down buttons Press Sel to enter the control menu b Select H POSITION to adjust the horizontal position of the image or V POSITION to adjust the vertical position of t
22. uces and distributes affordable virtual reality hardware software and systems 5DT can also develop custom systems for all your VR needs SDT s focus is Virtual Reality Training Systems and Virtual Reality Peripherals The Virtual Reality Hardware currently produced by SDT includes e 5DT Data Glove 5 Right and Left e 5DT Data Glove 5 W Wireless Right and Left e SDT Data Glove 16 Right and Left e SDT Data Glove 16 W Wireless Right and Left e 5DT Data Glove MRI 5 For Magnetic Resonance Imaging environments e 5DT Data Glove MRI 16 For Magnetic Resonance Imaging environments e 5DT Head Mounted Display HMD 800 e 5DT Head Mounted Display HMD 800 Stereo e 5DT Virtual Binoculars Mono and Stereo e SDT 3 DOF Orientation Tracker e 5DT Space Controller Some of the Training Systems Computer Based Training CBT Training Simulators and Technology Demonstrators that have been developed by 5DT include Automotive e Driver Training Simulator e Road Safety Training System Aviation e Airspace Visualizer e Air Traffic Control ATC Training Simulator e Experimental Avionics Testbed e Flight Visualization System e Unmanned Aerial Vehicle UAV Training Simulator Defense e Air Defense Training Simulator e Fiber Optic Guided Missile Training Simulator 2 e Integrated Virtual Battlefield e Rocket Launcher Training Simulator e Stand off Weapon Training Simulator and Visualizer High Voltage e High Voltage L
23. warranty Not for resale No commercial value Amount shown is for customs purposes only h If you are shipping the unit internationally you must supply attach a commercial invoice with your shipment otherwise the customs authorities in the destination country will not release the shipment The invoice must indicate a value We suggest that you assign a value of US 50 maximum on the invoice so that 5DT is not required to pay excessive import taxes on this product i It is important that you assign the same maximum value of US 50 to both the invoice and the courier waybill j lf you do not adhere to the warranty claim instructions and SDT has to incur costs to release the shipment from customs these costs will be for your account 5DT will not return your product until these costs are paid SDT is not responsible for any damage that may occur during shipping Ship via courier to your supplier or if arranged to US and Americas 5DT Inc 2005 De La Cruz Blvd Suite 292 Santa Clara CA 95050 USA Tel 1 408 748 1316 Fax 1 408 748 1329 e mail support us 5dt com Rest of World 5DT Fifth Dimension Technologies 25 De Havilland Crescent P O Box 5 Persequor Park 0020 Pretoria South Africa Tel 27 12 349 2690 Fax 27 12 349 1404 Email support 5dt com 34
24. x SVGA Cable 2 x RCA to RCA Cable Figure 2 5DT HMD 800 Stereo Accessories 5 Connecting the HMD 5 1 Connecting Electric Power To connect power to your 5DT HMD 800 please follow these steps a Connect the power input terminal of the AC adapter to the DC power input terminal of the control box Figure 3 and Figure 4 Make sure that the line voltage of the power adapter AC adapter is the same as the line voltage in the country where the HMD will be used For example if the line voltage of the power adapter is 100 120V AC it should not be used in a country where the line voltage is 220 240V Using an incorrect power adaptor may cause it to explode Figure 4 Connecting Electrical Power to the 5DT HMD 800 Stereo b Plug the AC power adapter into the power outlet on the wall or into a PC power plug according the type of power supply supplied with your HMD c Turn on the AC power switch d Press the Power On Off button on the control box and the power lamp will switch on 5 2 Connecting your HMD to a PC For the 5DT HMD 800 To connect your 5DT HMD 800 to a PC follow these steps a Connect the supplied D sub SVGA cable to the SDT HMD 800 control box and to the output of your video card b Connect the audio connection cable of the SDT HMD 800 as shown in Figure 5 Figure 5 Connecting the 5DT HMD 800 to a PC For the 5DT HMD 800 Stereo To connect your 5DT HMD 800 Stereo to a PC follow these steps a
Download Pdf Manuals
Related Search