USER MANUAL - Institut für Photogrammetrie und GeoInformation
Contents
1. B images is not just a simple shift of neighboured columns like in the case of ASTER images it includes a very strong trend figure 4 The grey value differences also vary over the scene like shown at the 4 lines from different parts of the scene in figure 4 right hand side Figure 5 corrected EROS B image Build up area in corrected EROS B image It was not possible to remove the whole striping figure 5 left nevertheless the stripping did not disturb any more the object identification figure 5 right like it was before With WorldView 1 satellite images with 0 45m GSD distributed with 0 5m GSD are available Soon this will be followed by GeoEye 1 and WorldView 2 with similar resolution This corresponds to aerial images with an approximate scale between 1 15 000 and 1 25 000 showing the competition of space and aerial images as it can be seen in figure 6 showing a lot of details Figure 6 Dolmabahce Palace Istanbul in WorldView 1 image 0 5m GSD 29 incidence angle Figure 6 also shows some general problems for mapping This image has been taken with an incidence angle of 29 In build up areas such a view direction causes remarkable occlusions and the on screen digitizing with ortho images 1s difficult Images with 0 5m GSD can be used for mapping in the scale 1 5000 The accuracy requirement of maps usually is in the range of 0 2mm up to 0 3mm in the map scale or 1m up to 1 5m for the map scale 1 5000 corresponding to 2 u2. Topographic mapping from space K Jacobsen G Buytiksalih Institute of Photogrammetry and Geoinformation Leibniz University Hannover BIMTAS Altunizade Istanbul Turkey KEYWORDS WorldView 1 IKONOS QuickBird OrbView 3 EROS B mapping information contents ABSTRACT Mapping today is a data acquisition for geographic information systems GIS Actual GIS information is required for any project planning Especially in developing countries often no actual information is available The data acquisition can be based on aerial but also on space images for topographic maps up to a scale 1 5000 Sometimes aerial images are not available or classified and photo flights may be expensive and time consuming if no aerial survey craft is stationed in the country So the use of space images for mapping often is an economic solution The ground sampling distance GSD has been shown as the key factor for object identification In addition the object contrast atmospheric condition incidence angle sun elevation and azimuth spectral range and multispectral information plays a role With WorldView l a GSD of 45cm is available distributed with 50cm GSD corresponding to medium aerial photo scale But also with QuickBird 62cm GSD IKONOS 82cm Im GSD OrbView 3 1m GSD and EROS B 0 7m GSD as well as with the other new very high resolution optical space imagery a topographic mapping is possible The results of mapping using QuickBird IKONOS
3. ages can be used for the generation of large scale topographic maps also under the more difficult situation of urban areas The geometric accuracy 1s not the limiting factor for the map scale it is limited by the information contents of the images that means the possibility of object identification However in relation to a topographic map 1 5000 not all objects could be mapped This confirms the rule of thumb that a GSD of at least 0 1mm in the map scale is required or reverse that IKONOS and OrbView 3 images can be used for the topographic map scale 1 10 000 With the 0 6m GSD of QuickBird images more details can be seen like with 1m GSD also the morphologic details are better but the details of the reference map has not been reached Of course this 1s also influenced by not so experienced operators and the extreme difficult test area but also with aerial images not all details can be extracted and a field check is required In not so mountainous terrain and in planned build up areas it is quite easier to generate topographic maps and QuickBird as well as WorldView 1 images can be used up to the map scale 1 5000 Also the EROS B images are including a similar information contents if the striping is removed The map scale 1 5000 is sufficient as base of a cadastre or a land consolidation as well as for urban planning Not only the GSD also the imaging conditions are important The sun elevation plays a major role because mapping in the shadow
4. and OrbView 3 images are compared with large scale topographic maps The influence of pan sharpening against panchromatic images is shown 1 INTRODUCTION 80 of the available information has a positional relation requiring geo positional knowledge of our environment which may be included in a Geo Information Systems GIS Topographic mapping today is a data acquisition for GIS It is required as basic information for any planning Without actual information about the environment no country or local administration can be managed Especially in developing countries we have a growing inequality between rural and urban population leading to migration to larger cities This again leads to problems in rural and urban areas causing unplanned growth in cities and development of slum areas The globalizing economy causes international competition of farm products farmers do not invest if they do not believe to reach a satisfactory quality of life causing a degradation of rural areas and agricultural production It is necessary to increase of living and working condition in rural areas to reduce the migration A possibility for this is a land consolidation with a rearrangement of ownership for the improvement of production and working conditions on farm land and in forests sustainable development In addition the migration causes severe problems up to unmanageable conditions in the cities requiring a strict urban planning An important pre condition for an
5. ap In fact there is only a limited difference between mapping with panchromatic and pan sharpened images Especially few additional smaller buildings in unplanned areas lower centre of maps in figure 12 have been mapped with pan sharpened images But the color is helpful for object interpretation and speeds up the data acquisition The higher resolution of QuickBird allows the plot of few additional unpaved paths and shorter streets located in shadows or hidden by buildings in the IKONOS scene The result based on IKONOS and OrbView 3 is not too different only very few details have not been mapped with OrbView 3 As result of mapping also with other space images like SPOT 5 IRS 1C and KOMPSAT 2 the required GSD for the identification of average size objects having average contrast is shown in table 2 Because of the lower limit for the requirement of 2m no major difference of mapping with IKONOS OrbView 3 and QuickBird can be seen in the maps shown in figure 12 Nevertheless with QuickBird images more details of the buildings can be mapped The EROS B images have been used in a different area so the comparison with the other very high resolution images is difficult but the information contents is very close to QuickBird images po required GSD urban buildings 2m Tale 2 required GSD for object foot path 1 2m identification under usual conditions minor road network Sm railroad Sm 4 CONCLUSION Very high resolution space im
6. entification as it can be seen in figure 9 and 12 Nevertheless experienced operators can identify nearly the same amount of image content without support of the colour This influences more the required time for mapping Figure 10 same area in different space images Turkey The object identification is also depending upon the image quality figure 10 OrbView 3 and IKONOS have nominally the same GSD nevertheless OrbView 3 images are always looking a little less sharp than IKONOS images This is caused by staggered CCDs used by OrbView 3 Orbview 3 has a projected pixel size of 2m but neighboured pixels are over sampled by 50 leading to Im GSD Of course with such method not the same imaging quality can be reached like with images where the projected pixel size is close to the GSD like in the case of IKONOS In addition the QuickBird image having 0 61m GSD demonstrates the advantage of higher resolution for the identification of object details Figure 10 shows also the difference of object identification of planned buildings in the upper part to unplanned buildings in the lower part The unplanned buildings are smaller and not regular arranged making the mapping quite more difficult Planned buildings Unplanned buildings Figure 11 Planned and unplanned buildings Brazil in IKONOS scene The different situation of planned and unplanned buildings can also be seen in image 11 In the same IKONOS scene the different building types are
7. ines the required accuracy of the height model The accuracy requirement of a map or ortho image depends upon the map scale which is related to the GSD In any case a standard deviation of 2 GSD is sufficient in most cases also 3 GSD are tolerated 3 REQUIRED GROUND SAMPLING DISTANCE FOR MAPPING Geo information systems usually include the objects with the national coordinates so by simple theory they are not related to a scale but the details of information as well as the accuracy is related to a presentation scale So also for a GIS a map scale can be specified Experiences with generation of topographic maps based on high and very high resolution space images Topan et al 2004 Jacobsen Buytiksalih 2006 resulted in the requirement of 0 1mm GSD in the map scale like 0 1mm x 50000 5m GSD for the map scale 1 50 000 or 1m GSD for the map scale 1 10 000 figure 3 But also for smaller map scales the GSD should not be larger than 5m because some objects have to be shown in any case also in small scale maps Of course this rule of thumb is valid for usual objects for very small structures even 0 05mm in the map scale may be required On the other hand thematic maps limited to special objects may be possible also with a lower resolution Figure 3 required GSD for generation of topographic maps 000 Sc I 000 05 1 4 OPTICAL SATELLITES As mentioned before depending upon the map scale the required GSD is defined limiting the usable sa
8. may be quite difficult A larger incidence angle may cause not acceptable occlusion in city areas On the other hand a larger incidence angle gives an oblique view like used by Pictometry this may be helpful for object interpretation especially by untrained staff The colour is helpful for object identification speeds up the mapping but does not lead to more details and higher accuracy REFERENCES Jacobsen K Buyuksalih G 2006 Mapping from Space a Cooperation of Zonguldak Karaelmas University and University of Hannover 5 Turkish German Geodetic Days Berlin 2006 http www ipi uni hannover de access 4 2008 Jacobsen K 2007 Orientation of high resolution optical space images ASPRS annual conference Tampa 2007 on CD Topan H Buyuksalih G Jacobsen K 2004 Comparison of Information Contents of High Resolution Space Images ISPRS Congress Istanbul 2004 IntArchPhRS Vol XXXV B4 pp 583 588 Topan H Buyuksalih G Jacobsen K 2005 Information contents of High Resolution Satellite Images EARSeL workshop 3D remote sensing Porto 2005 on CD http www ipi uni hannover de access 4 2008
9. n ground control points Jacobsen 2007 Ground positions are 3 dimensional with just one image point having just 2 coordinates only the direction of the ray from the projection centre to the ground position is determined figure 1 The correct ground position can be computed by intersection with 2 images or with the ground height information usually available as digital elevation model DEM Also if the images are available as projection to a plane with constant height with geo coded position named as level 1B Geo or Ortho Ready Standard such an image corresponds to the position shown as rectification in figure 2 In any case a so called terrain relief correction 1s required to get the correct geo position or in other words an ortho image has to be generated In an ortho image the points have the location of a map F Projection centre DL DZ tan v JT ee map map ortho rectification Figure 1 3D point determination Figure 2 ortho image Maps can be generated by stereo measurement based on 2 overlapping images taken from different projection centres or by on screen digitizing of ortho images Because of the expensive space images usually an on screen digitizing of ortho images is preferred For this a DEM with sufficient accuracy and point spacing is required Discrepancies of the height DZ are causing a positional error depending upon the incidence angle v formula in figure 2 The incidence angle of a space image determ
10. optimal land management is the registration of land ownership With certified land ownership the owners can get bank credits with good conditions because of the security by the ownership All this requires the knowledge of the actual situation of a country which is today not possible without updated GIS information Traditionally the required detailed mapping was based on aerial images With the today available very high resolution space images with up to 0 5m ground sampling distance GSD it 1s possible to use space images instead of aerial images They have the advantage of simple availability and are not restricted by classification like it is the case for aerial images in several countries In addition no photo flight is required which is economic only for covering larger areas with space images just the required information can be ordered 2 PRE CONDITION FOR MAPPING A geometric correct mapping requires the knowledge about the relation of the ground position to the corresponding image position or in other words the image orientation The approximate relation between ground and image position is known by the direct sensor orientation of the satellites based on GPS positioning of the satellite gyros and star sensors It may be available in the meta data of the image or the sensor oriented rational polynomial coefficients RPC delivered together with the image This orientation usually is not precise enough requiring an orientation based o
11. p to 3 GSD For an accuracy of 1m of the ortho image generation a DEM with a standard deviation of 1m tan v v incidence angle or 1 8m for 29 incidence angle is required Not many height models with such accuracy are available reducing the tolerable image incidence angle for mapping purposes On the other hand images with such an incidence angle are similar to the oblique image combinations used by Pictometry or Multivision They include additional information about the facades making an interpretation also for not photogrammetrists simpler Figure 7 demonstrates the problems of occlusion on the other hand it shows that in this image a mapping in shadow areas is not a problem Mapping in the shadows depends upon the radiometric resolution being 12 bit for WorldView 1 the used spectral range and the atmospheric conditions The light in shadows is caused by scattering in the atmosphere which is quite stronger for short wave length So the shadows are dominated by blue light In the case of a very clear atmosphere there is not so much light in shadows Figure 8 IKONOS images Zonguldak ken with different s sun TES of 46 41 A different situation of shadow areas is shown in figure 8 Topan et al 2005 in this case no details can be identified in the shadows In such a case high sun elevation is important IKONOS panchromatic IKONOS pan sharpened Figure 9 influence of colour to object recognition Colour simplifies the object id
12. shown Again the unplanned buildings are quite smaller like the planned buildings and the arrangement is not regular at NL JES AS PWT Meam Cab LAS at ERR Osy OrbView 3 panchromatic Turkish topographic map 1 5000 Figure 12 mapping with panchromatic and pan sharpened space images The influence of the GSD to the object identification is obvious in figure 13 With 2 5m GSD large and isolated buildings can be identified and mapped smaller buildings in most cases can be identified but mapped only with a symbol Of course this is quite different for 0 5m GSD here any chimney and visible window can be seen Cartosat 1 2 5m GSD WorldView 1 0 5m GSD Figure 13 influence of GSD to object recognition In figure 12 the result of on screen digitizing of ortho images is super imposed to the ortho images Panchromatic and pan sharpened IKONOS and QuickBird images and panchromatic OrbView 3 scenes have been vectorized For medium and larger buildings with regular roof shape the mapping is easy with all images Sometimes concrete roofs cannot be separated from the surrounding garden if no shadow is increasing the contrast Even in the very high resolution QuickBird images sometimes the contrast of buildings is not sufficient for a precise mapping The side line of roads cannot be extracted since they are located in shadow or occluded by buildings and trees and not in any case there is a clear side line in nature like shown in the topographic m
13. tellite images for the specified map scale In the last years especially the very high resolution satellites have been used for mapping table 1 pan multi spectral IKONOS Pp 082 32 PB QuickBird o 061 244 A po 4 nocolour S KOMPSAT 2 EE e E past OrbView 3 EROS B elliptical orbit Cartosat 2 Worldview 1 distributed with 0 5m GSD no colour Table 1 very high resolution optical space systems 14 14 Resource DK1 28 10 16 In addition to the very high resolution optical space images stereo systems like Cartosat 1 and ALOS PRISM having 2 5m GSD are used They are equipped with 2 respectively 3 cameras allowing a stereo imaging within the orbit Also SPOT 5 has with the high resolution stereo HRS an additional stereo sensor It has 5m x 10m GSD The images are usually not distributed only the generated height models are sold SPOT S5 can be used with its 5m GSD or the 2 5m GSD of the supermode also for small scale mapping as well as FORMOSAT having 2m GSD IRS 1C and 1D as well as Resourcesat with 5 8m GSD also can be used for mapping in the scale 1 50 000 5 MAPPING Some images have to be improved before they can be used efficiently for mapping purposes For example EROS B images having 0 7m GSD are strongly be influenced by striping Such a striping only can be caused by staggered CCD lines a combination of 2 neighboured CCD lines which are shifted 0 5 pixels against each other The striping of the EROS
Download Pdf Manuals
Related Search