USER MANUAL - Winter Holztechnik
Contents
1. sal III Safety warming and symbol 2 IV Main feature and using of the machine 3 V Overall and structure of machine 3 i Overallofmachne Sr 3 ii Main structure of machine 4 VI Main technology parameter of machine 8 VIL Loading and transport of machine 9 VIII Install debug and operation of machine 9 E B Ba GUE 9 il FO BOPA HON SFS en erg 10 IX Failure and solution 11 X Maintenance of machine 11 XI Electrical principle diagram 13 XII Electrical fittings detail lists 14 XIII Gluing working principle _ __ _______ 15 XIV Fitting detail of machine 16 Progress with the time and develop into the future I User manual i Operation of user manual Who will operate the machine should be peruse well of the user manual and must understand the procedure safety operation maintain etc the user manual introduced and put it close to the machine in order to read convenience ii Copyrightof this user manual This copyright of this user manual is belongs to Tongan company This instruction is for the buyer and operator using the content of it is forbidden to copy send out and reading by other way If who disobey this principle our company will be run the responsibility II Safety devi2. when the machine lifting forbidden around Forked vehicle anyone The right picture is the forklift loading c After loading put away all the safety device loading tool and temporary device VIII Install debug and operation of machine i Install debug A Environment required of install the machine The requirement environment of install machine 1 Install dimension 4000x4000x4000mm temperature 10 C 55 C Atmosphere humidity 85 Height above sea level hereinafter1000M B Lay out of machine The machine should be lay out on the flat concrete After lay out the machine adjust the level of the machine to make sure the front back right and left four point on the same height C Distribution According the distribution of the required connect into the voltage current and frequency on the power terminal ii Operation A Safety check before operate the machine Before operate the machine first check the machine carefully to make sure safety OD Check every safety device correct firmly or not Check every rotating and connecting section firm or not After carry out the safety protection switch check every motor rotating section agility smooth or not After finish above working point start the Start button check every rotating section correct or not The direction is Face to the machine the up chromeplate roller that is up glue quantity adjustable roller rotating direction is clock
3. caustic It is widely used in the veneer factory furniture manufacturer Acoustics device factory V Overall and structure of machine i Overall of machine A Workpiece thickness adjustable wheel B Electrical section D Safety protection section C Gluing section E Glue box section F Adjustable wheel of glue quantity G Dniving section t ii Main structure of machine The machine is compose of Gluing section Workpiece thickness adjustable wheel Electrical section Driving section Gluing section body section and Safety protection section A Gluing section tap glue quantity adjustoent underside gule adjustment wand It is compose of up and low glue roll up and low glue quantity adjustable roll side board glue quantity adjustable device etc Just as the photo The glue roller is made as steel tube processed and with the glue on the surface The glue quantity adjustable roller is made with the steel tube which after chromeplate processing The Quantity roll and adjustable roller is install on the right and left side board The roller and adjustable roller is install the rotating chain wheel It is used to finish the power rotating You can use the nght and left hand wheel A to adjust the quantity When clock wise rotating the glue quantity adjustable roller close to the roller when anticlock wise rotating it is leaving Note Before add the gluewater into the ro
4. not the machine whether install the tread working earth wire and close the breaker V Maintenance of machine i Daily maintain A Keep the machine clean and keep every driving section and connection lubricant B Forbidden to put anything on the machine C After every gluing working clean the machine must be drain out the sewage ii Weekly checking of machine A Every time before working should be check every moving and safety device correct or not and operate the machine one time and check the moving correct agility and firmly or not B Every moth should be do a carefully checking especially for checking the up and low roller abrasion condition and every safety protection fitting condition and adjust and replace C For the moving section every shift should be add the lubricant oil If operation pbs pe the machine for a long time there are any abnormity sound should be stop checking and maintain and replace the fittings iii Maintain when stock the machne A If the machine does not operating should be clean the machine and add lubricant oil on every driving section and packing well B Should be put the machine inside the ventilative dryness room avoid the sun shine and rain directly VI Electrical principle diagram DZ47 63 C25 3P ee e VII Electrical fittings detail list zZ Description bebe rr fiel Conto mer pri Izu Ama pese im An ma ie
5. wise the up roller direction is anti clock wise If you find any un correct direction that you can exchange any two wire of the three phase wires B Operation Adjust the required workpiece thickness by the right and left side worm wheel Adjust the required glue quantity by front and back worm The right and left wheel linkage till quantity of right and left is even After make sure the above processing that you can start working press the Start button to start the machine Then you can start working After finish working press the red stop button to make the machine stop C working after operated After the machine stop anti clock wise to rotating the adjustable hand wheel to enlarge the clearance between roller and glue quantity adjustable roller then use the long handle brush to rinse till it clean then drain out the sewage IV Failure and solution Failure Reason Close the general power Open the power switch and control power The breaker does not Open the electrical case and close the Press the operation close breaker button but can not The connector does not Check the circuit whether broken or operate work or hot relay broken overload and repair Does not cover the safety Cover t protecton The machine sudden Check the motor isolation qualify or Short circuit or breaker stop when it is
6. USER MANUAL DOUBLE FACE GLUE SPREADER MASCHINE Henrik Winter Holztechnik GmbH Druckereistr 8 04159 Leipzig Tel 49 0 341 4619021 Fax 49 0 341 4618358 Funk 49 0 171 2820443 Em il info winter holztechnik de Internet www winter holztechnik de Operator should read user manual carefully to truly understand the function and operating skills Reliable earthed device should connect with machine before operation The machine should connect with suitable power check f the currency frequency voltage are right Before operation confirm if the direction of running cutter saw are all right Checke the safety protecting device are normalor not if it is loose or damaged replace it in time Operator should wear tighten clothes in operation it is forbidden to wear loose clothes or wear tie watch necklace who have long hair need to wear hats All safety device can not be removed in running time Operator are forbidden to leave position when machine is running It is forbidden to process workpiece which exceed the processing range of machine 10 Some one drink too much or not in good healthy are forbidden to operate machine 11 Shut down main power supply before checking maintenance cleaning 12 Shut down main power supply after operation it is forbidden to leave before machine stop completely CATALOGUE I Ser manual nor 1 II Safety device and protection
7. ba mn an wew foe man o a me me Line 10 Emergency stop LA38 10 be button VIII Gluing working principle double face glue working principle top glue wand zlue top glue quantity adjustment workpiece thickness KE adjust glue es quantity __ feeding d direction adjustment underside gule adjustment vand LLL MV LLLLLLLL SAL LLL LLL LLL N di xD adjust the gule quantity i gt underside gule wand pastern basin single face gluing principle guling wand gule oH YS out direction of guling working gule quantity adjustment support pole pastern basin IX Fittings detail of machine I Light roller bearing room f Note Light roller bearing cover Chain wheel nm wy Double chain wheel Driving big gear wheel oO or periz Gerezi 23 24 25 Model A belt EF 36 l 2 2 4 31 Big belt Deep channel all bearing 30 Pash charnel bali vering lu peda enna Packing List DOUBLE FACE GLUE SPREADER MACHINE lset Weight 750kg 7 User Manual 1 copy rf User Manual 1 2 3 1 copy Cia pe Packing list Inspector for packing seal TI Date
8. ce and protection i Before operate the machine should be install the safety protection device correctly make sure working under safety condition li The safety device can be knock down under the condition of power shut down iii You can operate the machine under the all the safety device is working normal iv All the procedure transport install debug and maitain should be operate by the professional v Refer to the electrical install and maintain should be in charge by the professional vi Check the electrical device timing and deal with the loosen or broken electrical fittings in time Forbidden maintain with electrical when check and maintain should be shut off the power and keep somebody to see the power make sure the examine and repair person safety vii This machine just only can be used the no volatility flammable gluewater Sa SO t _ e LI e e e nm nn 7 III Safety warming and symbol i i The operator should be obey to the warmings if ignore will be injure anyone This symbol means when connect the power do not open this section or will be got electric shock This symbol means when operating do not put the hand into or it will injure IV Main feature and using of the machine This machine is mainly use to adhibit Veneer cabinetwork cord board corde board of furniture board and PVC or Double faces timber lamination It can be use every kinds Gluewater which is no fierceness
9. ller and adjustable roller first should be adjust the opening between roller and adjustable roller When adjust rotating the left adjustable hand wheel till the two roller almost touch each Then you can add the gluewater into Note Before add the gluewater forbidden to put the adjustable roller close to the roller to start the machine or it will injury the surface of the roller u a A A B Workpiec thickness adjustable section It is compose of the adjustable hand wheel connected pole pole jointer and right and left worm wheel case etc Spreading thickness finished by rotating the two sides hand wheel The function of the worm wheel A is to adjust the thickness of gluing workpiece When A Connect pole clock wise rotating the up roller rising when anticlock wise it will downing For example if the workpiece thickness is 10mm rotating the hand wheel with clock wise to make the pointer point 9mm on the staff guage note Avoid to make the rubber on the roller abrasion too early So the opening between roller can not less then workpeice thickness generally about 0 5 2mm is perfect When spread the small workpiece should be use the length gluing or the roller can not using smooth to abrasion the roller that will cause the roller no even C Electrical control section It is compose of an AC connector and one Hot relay and the relay should be protect the 0 and short voltage and voerload protection and with tow a
10. n section There is install tt safety protection net to avoid the hand touch the roller moving section when the machine is working avoid to injure the GN Every time before operate the machine should be check the protection net normal or not If there are any broken should be adjust or replace in time The following picture A s travel switch When operating the machine the operate should be open the safety protection carefully Cover jointer pole rotating touch the travel switch then cut off the AC connector on the roller start to make the roller stop immediately to protect Safety net locknut VI Main technology parameter of machine Preduct MH6206 MH6106 MH6113 MH6213 Parameter name VII Loading and transport of machine This machine is the whole set structure When transporting must be fixed all the shockproof dampproof defend strike etc measures When the user loading should be required the professional person to carry out i Transport and stock environment requirement Transport and stock should be during 25 C 55 C If Under more than 55 C but less than 70 C environment the machine can not working over 24 hours li Loading a When loading the machine should be evacuate people and set the safety protection b Use the crane or electrical forklift which weight enough to loading the machine During the whole loading procedure should be make sure the machine 1s steady
11. uto recovery button to start and stop control the machine The reasonable circuit designed and easy operate control panel to operate the machine convenience and easy a Electrical section r A Control transformer B break phase and phase sequence protection relay C Roller start AC connector D Hot relay To protect the motor E Breaker To protect the short circuit A Controll panel A Start button Press this button to start the machine B Stop button Press this button to stop the machine D Glue tray section and drain The glue tray is made of the steel there is drain switch under the tray Every time finish gluing and clean you can press the switch to let the sewage out B drainage pipe Safety net Step of drain Cleaner Open the drain case on A Press the switch B to let the sewage to the tray After finish drain close the switch B then close the door E Driving section It is compose of motor A Reducer B elastic tighten chain C Motor is 100L 4 2 2KWInstalled way B3 Reducer is WD80I The rate is 1 30 the power is give out by motor drive the chain to up and low roller and up and low adjustable roller by reducer to finish gluir C we working Spring D is to auto adjust gear driving F Body section It is compose of steel and steel board The structure is simple ar A goodlook G Safety protectio
Download Pdf Manuals
Related Search