User's Guide Revolabs Fusion™ Wireless Microphone System
Contents
1. Radio congestion it is not continuing possible to make a radio for more than a few connection because there are seconds already too many nearby users or there is heavy radio interference Groups of five rapid RED OFF Unit is faulty Contact your AV flashes service provider for advice Revolabs Fusion Microphones must be fully charged and paired to the Fusion Base Station prior to first use 2008 REVOLABS INC All rights reserved No part of this document may be reproduced in any form or by any means without express written permission from Revolabs Inc Product specifications are subject to change without notice Part 295033 REV 1 122. the microphones press the red MUTE button on the Remote Control all microphones will flash red and no individual microphone can be unmuted until the remote MUTE button is pressed again All microphones will return to their prior state However if the tabletop microphone master mute has been enabled Refer to Set Up Guide the mute will work as follows in addition to the Remote Control MUTE button muting all of the microphones the Solo Tabletop microphone MUTE button will also act as a master mute and mute all active microphones Pressing any Tabletop microphone MUTE button or the Remote Control MUTE button will unmute all tabletop microphones All wearable and handheld adapter microphones in use will return to their prior state User s Guide Using Solo Tabletop Wireless Boundary Microphones The Solo Tabletop Wireless Boundary Microphones enable multiple conference attendees to use a single microphone The Tabletop Wireless Microphone shown on the following page is designed to provide optimum coverage when placed on a conference room table Mute button press to mute un mute and pair microphone 2 LED display visual status for mute un mute and pairing 3 Integral grille protects internal parts non removable 4 Audio jack accepts the 2 5mm plug for the earpiece 5 Charging port docks to Charger Base 6 Rubber feet non slip vibration absorbing pads To use the Revolabs Solo Tabletop Micropho
3. E button is pressed again All microphones will return to their prior state However if the tabletop microphone master mute has been enabled Refer to Set Up Guide the mute will work as follows in addition to the Remote Control MUTE button muting all of the microphones the Solo Tabletop microphone MUTE button will also act as a master mute and mute all active microphones Pressing any Tabletop microphone MUTE button or the Remote Control MUTE button will unmute all tabletop microphones All wearable and handheld adapter microphones in use will return to their prior state End a Call To end a call the user must push End even if the other callers have hung up Redial a Call To redial a the last phone number push Redial Adjust Volume To increase and decrease the volume use the Vol and Vol buttons Flash Button Flash works according to your phone system User s Guide Using the Fusion Charger Base When microphones are not in use they should be properly inserted into the Charger Base It is important to ensure that the system microphones are inserted fully in the base so that charging will occur 3 OOOO O 2 LED indicator power mute status indicator 2 Charger Bay charges up to 8 Microphones 3 Power Cord Receptacle power supply input on rear The Charger Base requires 5VDC power provided by the AC Adapter Plug the supplied AC wall adapter into an appropriate power
4. Revolabs Fusion Wireless Microphone System User s Guide y revolabs Revolabs Fusion Great audio wireless mobility and simple to install Simply plug the cable into the AV system or phone system and it works No software configuration is necessary Even the Fusion box is designed to be easy to use vertically or horizontally No equipment rack needed Just set the Fusion system on the credenza Video Conferencing Revolabs Fusion Wireless Microphone Solution is compatible with all of the major video conferencing solutions including Lifesize Polycom Sony and Tandberg It includes a remote control Decide on where you want to put the Fusion system whether you want to place it vertically or horizontally plug in the cables and you are ready to have great wireless audio in any conference room Audio Conferencing Plug the Fusion Wireless Microphone Solution into an analog telephone jack and you are on your way to great wireless teleconference calls There is a remote control dialer to dial the conference phone number You may connect to powered speakers connect to existing speaker system or connect to a new room speaker system to hear the call Decide on where you want to put the Fusion system whether you want it vertical or horizontal plug in the cables and you are ready to have great wireless audio in any conference room Flexible The Fusion System supports any combination of Solo Wireless Microphones Wearable Ta
5. abs Fusion To turn the Adapter off return the microphone unit to the Charger Base or press and hold the Mute button for 10 seconds until the LED turns solid RED and release button Important Always remove the microphone from the Adapter by pressing the latch switch and separating the parts before returning the Adapter to the Charger Base If the Adapter is moved too far from the Base Station 100 feet or 30 meters the connection will be dropped LED flashes all colors and the audio will mute After 15 seconds the microphone will beep 5 times and will continue beeping every 30 seconds to indicate that it is out of range Move the XLR Adapter closer to the Base Station and the connection will automatically be re established to its original state and the beeping will cease If not the XLR Adapter will continue beeping until it turns off in about 15 minutes Muting Microphones In the default setting each Solo microphone will mute only itself when its MUTE button on the microphone is pressed To mute all of the microphones press the red MUTE button on the Remote Control all microphones will flash red and no individual microphone can be unmuted until the remote MUTE button is pressed again All microphones will return to their prior state However if the tabletop microphone master mute has been enabled Refer to Set Up Guide the mute will work as follows in addition to the Remote Control MUTE button muting all of the micropho
6. bletop or XLR adapter for s handheld microphone Choose the right microphone for your meeting dynamics Rechargeable Revolabs Wireless Microphones have a rechargeable battery that provides eight hours of talk time after each full charge Revolabs Wireless Microphones recharge to 85 capacity in approximately 45 minutes Secure All of Revolabs Wireless Microphones use 128 bit authentication so that no one can listen in User s Guide Using the Fusion IR Remote Control Phone Dial Pad Vol increases volume Call dial tone End hang up Vol decreases volume Flash phone function Redial phone func tion Dial a Call To make a call push Call to get dial tone then dial the phone number on the Phone Dial Pad Answer a call To answer a call when the system is ringing push Call Mute and Unmute a Call Using Remote Control Mute Button To mute all of the microphones press the red MUTE button all microphones will flash red and no individual microphone can be unmuted until the remote MUTE button is pressed again To unmute press it again All microphones will return to their prior state Revolabs Fusion NOTE In the default setting each Solo microphone will mute only itself when its MUTE button on the microphone is pressed To mute all of the microphones press the red MUTE button on the Remote Control all microphones will flash red and no individual microphone can be unmuted until the remote MUT
7. imately 8 hours of talk time User s Guide Using Revolabs Solo Microphones and Microphone Adapters Use any Solo Microphone microphones with your Revolabs Solo Executive system e _ Revolabs Solo Wearable Wireless Microphone e Solo Tabletop Wireless Boundary Microphone e Solo Universal Wireless Adapter for Handheld Microphone Using Revolabs Solo Wearable Wireless Microphone The Revolabs Solo Wearable Microphones shown in the following figure are paired to the Base Station and can be worn on the user s shirt pocket lapel or on a lanyard Microphone port direct port toward mouth for best audio pickup 2 Noise cancelling port do not block opening 3 Mute Button press to mute un mute and pair microphone 4 Pocket clip also used to attach microphone to lanyard 5 LED display visual status for mute un mute and pairing 6 Earpiece jack accepts the 2 5mm plug for the earpiece 7 Charging port charges in Charger Base Please note that the audio heard through the earpiece will be the far end only If you need hearing assistance to hear the audio from both the far end and the microphones in the room you must reconfigure the Fusion System Refer to the Fusion Set Up Guide Revolabs Fusion Revolabs Solo Wearable Microphones turn on and mute automatically when removed from Charger Base to reduce noise while being attached The microphone has a clip on the back which allo
8. ll continue beeping until it turns off in about 15 minutes Muting Microphones In the default setting each Solo microphone will mute only itself when its MUTE button on the microphone is pressed To mute all of the microphones press the red MUTE button on the Remote Control all microphones will flash red and no individual microphone can be unmuted until the remote MUTE button is pressed again All microphones will return to their prior state However if the tabletop microphone master mute has been enabled Refer to Set Up Guide the mute will work as follows in addition to the Remote Control MUTE button muting all of the microphones the Solo Tabletop microphone MUTE button will also act as a master mute and mute all active microphones Pressing any Tabletop microphone MUTE button or the Remote Control MUTE button will unmute all tabletop microphones All wearable and handheld adapter microphones in use will return to their prior state Please note that the audio heard through the earpiece will be the far end only If you need hearing assistance to hear the audio from both the far end and the microphones in the room you must reconfigure the Fusion System Refer to the Fusion Set Up Guide User s Guide Using the Solo XLR Microphone Wireless Adapter The Revolabs Solo Universal Wireless Adapter for Handheld Microphones shown in the following figure is connected to your existing handheld dynamic microphones for wireless freedom d
9. ne e Remove the microphone from the Charger Base to turn on and automatically mute the microphone indicated by a flashing RED LED during placement on the conference table e Tabletop microphones should be centered on the table with the integral grill pointed toward the users uni directional or centrally located between users Omni directional from 2 to 5 feet 75 to 1 75m away It is always better to be as close to the person speaking as possible but avoid placing the microphone where it might be blocked by equipment or meeting paperwork Also do not place microphones too close to an audio or video conference speaker to avoid echoes Revolabs Fusion e With the microphone in position un mute the microphone by pressing and releasing the Mute button confirm by viewing flashing GREEN LED e To turn microphone off return the microphone unit to the Charger Base or press and hold the Mute button for 10 seconds until the LED turns solid RED and release button e If the microphones are placed too far from the Base Station 100 feet or 30 meters the connection will be dropped LED flashes all colors and the microphone will mute After 15 seconds the microphone will beep 5 times and will continue beeping every 30 seconds to indicating it s out of range e Move the microphone closer to the Base Station and the connection will automatically be re established to its original state and the beeping will cease If not the microphone wi
10. nes the Solo Tabletop microphone MUTE button will also act as a master mute and mute all active microphones Pressing any Tabletop microphone MUTE button or the Remote Control MUTE button will unmute all tabletop microphones All wearable and handheld adapter microphones in use will return to their prior state User s Guide Indicator Lights Equipment Use Microphone LED Base Station Meaning LEDs Microphone in Charger Solid RED OFF Charging in Progress Base Solid GREEN OFF Charging Complete Microphone not in OFF OFF Microphone powered OFF or Charger Base battery discharged One RED flash RED Flashing Microphone master muted by every 1 5 seconds remote control or tabletop master mute Two RED flashes RED Flashing Microphone paired and muted every 1 5 seconds GREEN flash every GREEN Flashing Microphone paired and live 1 5 seconds Solid RED Solid RED Pairing mode or confirmation of powering down Alternating slow OFF Microphone or channel not GREEN and RED or paired Alternating slow GREEN and RED YELLOW flash alternating GREEN Flashing Microphone low battery with GREEN mic live YELLOW flash alternating RED Flashing Microphone low battery with two RED flashes mic muted Alternating RED YELLOW OFF Searching for a connection or GREEN YELLOW out of radio range The Microphone will try to re establish the link for about 15 minutes and then turn off Rapid RED flashes OFF
11. outlet 10 240 AC 50 60Hz The power LED on the Charger Base will illuminate Charging the Microphone Batteries First time use before using the wireless microphone the first time charge the batteries in the microphones for eight hours or overnight in the Charger Base Revolabs Fusion Recharging when the YELLOW LED starts to flash intermittently on the microphone the battery has 30 minutes of charge remaining To charge the batteries place microphones into the Revolabs Solo Executive Charger Base and the mic LED s will display a 5 blink self test During charging the LED indicator will be RED when mics are discharged and turn GREEN when charged The microphones are muted while in the Charger Base In normal use batteries should fully charge in about 2 hours and can be quick charged to 85 capacity in 45 minutes Over time years batteries gradually wear down and require longer charging times This is normal Always return microphones to the Charger Base when not in use The batteries of microphones left in the Charger Base remain solid GREEN Important The Lithium Polymer rechargeable batteries that power the microphones are not user serviceable Please contact Revolabs www revolabs com or your AV service provider for replacement instructions and to assure the proper disposal method is used Warning Never dispose of batteries in a fire because they may explode NOTE A fully charged battery provides approx
12. uring open microphone meetings Q amp A sessions classrooms etc Ss 3 i a Zz M Mute button press to mute un mute and pair microphone 2 Rubber collar durable and impact strain protection 3 XLR Female connector balanced audio for dynamic microphones 4 LED display visual status for mute un mute and pairing 5 Audio Out port accepts the 2 5mm plug for the earpiece 6 Power Charging Port docks to Charger Base Please note that the audio heard through the earpiece will be the far end only If you need hearing assistance to hear the audio from both the far end and the microphones in the room you must reconfigure the Fusion System Refer to the Fusion Set Up Guide To use the Revolabs Solo Universal Wireless Adapter e Remove the Microphone Adapter from the Charger Base e The adapter turns on and mutes automatically when removed from Charger Base flashing RED LED The XLR Microphone Adapter is attached to a standard dynamic microphone to convert it from a wired microphone to a wireless microphone see following figure e The Adapter does not provide phantom power or bias current so it cannot be used with condenser or electret microphones e With the microphone attached un mute the Adapter by pressing and releasing the Mute button confirm by viewing flashing GREEN LED NOTE If the microphone has an on board mute switch this switch must also be un muted prior to use Revol
13. ws the microphone to be easily attached onto a shirt pocket blouse lapel or lanyard To use the Wearable Microphone e Remove the microphone from the Charger Base e Attach the microphone to clothing or to a lanyard close to the mouth within 6 12 inches 15 30cm is recommended Make sure microphone is attached securely with the microphone port pointed up toward mouth e With the microphone in the wearing position un mute the microphone by pressing and releasing the Mute button confirm by viewing flashing GREEN LED If the volume is too low move the microphone closer to the mouth e To turn microphones off return the microphone unit to the Charger Base or press and hold the Mute button for 10 seconds until the LED turns solid RED and release button e Ifthe microphones are moved out of range of the Base Station 100 feet or 30 meters the connection will be dropped LED flashes all colors and the microphone will mute e After 15 seconds the microphone will beep 5 times and will continue beeping every 30 seconds to remind the user to return the microphone to the conference room If the microphone is moved back into range within 15 minutes the connection will automatically be re established to its original state and the beeping will cease If not the microphone will turn off Muting Microphones In the default setting each Solo microphone will mute only itself when its MUTE button on the microphone is pressed To mute all of
Download Pdf Manuals
Related Search