Owners Manual v2
Contents
1. Owner s Manual for Remington Model SPR 210 and SPR 220 Side By Side Shotsuns A y Safety is Critical to Performance A superbly crafted gun is only as good as the hands that hold it You can never be too careful Shooting accidents are often caused by careless oversights such as failing to control the direction of the muzzle failing to fully engage the safety leaving ammunition in the chamber or using improper loads These oversights can result in the destruction of life limb or property There s no calling back a bullet once it s been fired so it s critical that you know the principles of safe gun handling and storage before you ever take your new Remington firearm out of the box The proper use and performance of your firearm depends on correct assembly and maintenance so it s critical that you familiarize yourself with the information in this instruction book Even if you re a veteran shooter with a collection of Remington firearms take the time to read this literature Not all firearms are the same That means the first step in safe handling is to learn the features and requirements of your new Remington THE TEN COMMANDMENTS OF FIREARM SAFETY With the privilege of owning a firearm comes the responsibility to use it safely You must understand and follow the Ten Commandments of Firearms Safety at all times These time honored safety rules apply to your ownership and handling of any firearm They must govern your actions whenev2. D Using the bore brush with powder solvent scrub the interior of the barrel and chamber to remove any powder and lead residue in the bore Always and lastly swab the interior of the barrel with a cotton patch with gun oil to coat and protect the bore and chambers from rust and corrosion m Any powder fouling on the firing wall barrel etc can be easily cleaned with a brush and powder solvent m All external surfaces should be wiped down with a light coat of rust preventative Avoid using too much oil as powder dust or other foreign material may get trapped in the oil This could lead to congealed deposits which may interfere with the safe and reliable operation of this shotgun G USE CAUTION while using solvents in gun bore cleaning Prolonged or excess contact with solvents can damage the gun s bluing and finish Be sure to wipe away all excess solvent and then lubricate with oil H A gun should be cleaned after firing In addition external parts should be wiped with an oiled cloth after handling A light oil is ordinarily all that is necessary in cleaning if the gun has not been fired or fired very little If a gun is used frequently it must be cleaned after each firing and regularly serviced by a professional gunsmith If the gun has been stored remove all excess oil and or grease before firing Always check to be sure that no cleaning patch or other obstruction remains in the bore or chambers before firing 16 DANGER
3. Ammunition Warning Firearms may be damaged and serious personal injury or death to the shooter or bystanders may result from any condition which contributes to the generation of excessive pressure or uncontrolled release of gas within the firearm Such adverse conditions can be caused by bore or chamber obstructions propellant powder overloads or by defective incorrect or improperly loaded and assembled cartridge components Even the strongest firearm can be blown up as a result of excessive pressure lt is extremely dangerous to use a cartridge whose pressure is greater than that developed by cartridges loaded to industry standards Ammunition Cartridges Notice We specifically disclaim responsibility for any damage injury or death occurring in connection with or as the result of the use of the shotgun with faulty non standard remanufactured hand loaded or reloaded ammunition or with cartridges other than factory cartridges for which the shotgun was originally chambered Lubrication Warning Firing a shotgun with oil grease or any other material even partially obstructing the bore may result in damage to the shotgun and personal injury to the shooter and those nearby Do not spray or apply lubricants directly on ammunition If the powder charge of a cartridge is affected by the lubricant they may not fully ignite yet the ener gy from the primer and or powder may still be sufficient to push the projectile or wad into the bore where it may b
4. the security lock 1 in a separate location away from the shotgun 2 in a secure location unknown and not accessible to others especially children Whether you secure your firearms by using the supplied security lock a gun lock or a safe or some other mechanism it is YOUR RESPONSIBILITY to store your firearms in such a manner that children and other unauthorized persons cannot gain access to them Important Parts of the Firearm Congratulations on your choice of a Remington Model 210 or Model 220 shotgun With proper care and if used in accordance with the Ten Commandments of Firearm s Safety and this owner s manual your shotgun should give you many years of dependable use and enjoyment The following picture depicts the main parts of your shotgun and will aid in understanding the instructions in this Owners Manual SAFETY MECHANISM STOCK MUZZLE RECEIVER FORE END BARREL TRIGGER TRIGGER GUARD This picture shows the main parts of a Remington Model SPR210 shotgun The picture will aid in understanding the instructions in this book External Control Parts Trigger Block Safety The safety mechanism of the shotgun provides protection against accidental and unintentional discharge under normal usage when properly engaged and in good working order The safety mechanism is not a substitute for the rules of safe gun handling Do not disengage the safety unless you are ready to fire the shotgun MAKE SURE YOU UNDERSTAND HO
5. trigger block safety until you are ready to fire and have the gun pointed safely downrange WARNING DO NOT LOAD SHOTGUN UNTIL YOU ARE READY TO FIRE 11 Loading and Unloading Your Shotgun cont d TO LOAD 1 Make sure the ammunition that you are using is the correct size and gauge The barrels are marked with the gauge and chamber size Barrels marked 3 76mm will use only 2 70mm or 3 76mm shot shells and must not be used with 3 89mm shells Barrels marked with 2 70mm will use only 2 4 70mm and must not be used with or 3 76mm or 3 89mm shells 2 Visually inspect the chambers and barrels for obstructions by breaking open the shotgun by depressing the locking lever and tipping the barrels down The chambers and barrels should be free of oil or grease or obstructions See Picture 21 Picture 21 3 After inspection load the correct type of shot shells into the chambers making sure that the shells are flush with the extractor See Pictures 22 and 23 then close the action by swinging the barrels up until they lock into the receiver and the top lever moves back to the center position If the top lever does not move to the center See Picture 24 break open the action again and check to see if the shot shells are fully seated in the chambers If the shells are fully seated then re close the action If the shot shells are not fully seated check the chamber for blockage and check the shells
6. 11 H awk Street Rockledge FL 32955 Manufacturer Izhevsky Mekhanichesky Zavod 8 Promyshlennaya str 426063 Izhevsk Russia 23 Kemington Remington is a trademark registered in the United States Patent and Trademark Office by Remington Arms Company Inc
7. 3 Picture 32 Picture 33 15 Manufacturer s Warning This firearm was manufactured to properly perform with the original parts as designed Itis your duty to make sure any parts you buy are correctly installed and that neither replacements nor originals are altered or changed Your shotgun has many parts that must relate correctly to other parts for safe and accurate operation Putting a gun together wrong or with modified parts can result in a damaged gun or personal injury or death to you or others Always let a qualified gunsmith work on your gun or at least check any work not performed by a gunsmith Firearms safety is your primary concern THE GUN OWNER MUST ACCEPT FULL RESPONSIBILITY FOR THE CORRECT REASSEMBLY AND FUNCTIONING OF THE FIREARM AFTER ANY DISASSEMBLY OR REPLACEMENT OF PARTS To Clean and Maintain Your Shotgun A Follow procedures for unloading shotgun as described previously B Follow procedures for disassembly of shotgun as described previously C Materials needed to clean this shotgun are a cleaning rod cotton bore patches brass bore brush powder solvent such as Remington BriteBore a small soft brush and good quality gun oil such as Rem Oil WARNING Lead or lead compounds are known to the State of California to cause cancer birth defects reproductive toxicity and other serious physical injury Those who clean firearms should take protective measures to avoid contact or exposure to such chemicals
8. Tungsten lron shot or Hevi Shot are subject to the same barrel and choke tube limitations as steel shot 2 On fixed choke guns shells loaded with steel Tungsten lron or Hevi Shot should be fired only in IC or Cylinder barrels DO NOT fire steel Tungsten lron or Hevi Shot shells in fixed barrels with Modified Improved Modified or Full choke barrels Lead Bismuth and Tungsten Matrix may be fired in all fixed choke barrels 3 On fixed choke guns slugs may be fired in only IC and Cylinder barrels DO NOT fire slugs in fixed choke barrels with Modified Improved Modified or Full chokes If you would like to buy extra choke tubes skeet trap extra full etc call 321 639 1432 22 WARNING Children are attracted to and can operate firearms that can cause severe injuries or death Prevent child access by always keeping guns locked away and unloaded when not in use If you keep a loaded firearm where a child obtains and improperly uses it you may be fined or sent to prison ADVERTENCIA A los ninos los atroen las armaside de fuego y los pueden hacer funcionar Ellos pueden causarses lesiones graves y la muerte Evite que los ninos tengon acceso a los armas de fuego guardandolas siempre con llave y descargadas cuando no las este utilizando Si usted tiene un arma de fuego cargado en un lugar en que un nono tiene acceso a ella y la usa indebidamente Le pueden dar una multa a enviarlo a la carcel REMINGTON I S P cio USSG 4
9. W THE SAFETY WORKS BEFORE YOU LOAD OR USE THE SHOTGUN The safety mechanism is a tang style located behind the top lever See Picture 7 To place the safety in the on or safe position pull the button all the way to the rear When in the on or safe position the safety blocks the rearward motion of the trigger s To place the safety in the off or fire position push the slide all the way to the forward When in the off or fire position a red dot is exposed behind the slide button You have now disengaged the safety and the shotgun is in the ready to fire position see Picture 8 l Picture 7 Picture 8 WARNING Do not touch the trigger s while moving the safety When operating the safety button make sure you push or pull it to the full extent of its travel in the desired direction either fully on or fully off Half safe or partially safe is UNSAFE WARNING The Shotgun is designed to and will FIRE when the trigger is pulled and the safety mechanism is in the off or fire position External Control Parts cont d Top Lever The top lever is located just forward of the safety mechanism See Picture 9 The top lever is used to break open the action to load and or unload the shotgun and to assemble and disassemble the shotgun To break open the action fully push the top lever to the right See Picture 10 Picture 9 Picture 10 AY WARNING When operatin
10. anism like you would treat any other mechanical device as something that could break or fail Not all safety mechanisms operate in the same manner Before using any firearm know and understand pre cisely how the safety mechanism on that particular firearm operates Never pull the trigger when the safety mechanism is in the safe position and keep your fingers away from the trigger while loading unloading and engaging or disengaging the safety mechanism O 4th COMMANDMENT Know Your Target and What s Beyond t Never fire a shot unless you know exactly where the shot is going and what it will strike Bullets and shot can travel great distances with deadly velocity When hunting game never fire at a sound a movement or a patch of color an impulsive shot can have tragic consequences A fellow hunter in camouflage may be mistaken for game by an impulsive shooter In addition to being sure of your target you must know what lies beyond the target In other words make sure of your backstop Also beware of ricochets never shoot at water or a hard surface O 5th COMMANDMENT Use Proper Ammunition Every firearm is designed to use only a specified caliber gauge or length of ammunition Use of the wrong ammunition can cause serious personal injury or death Itis your responsibility to make sure the ammunition exactly matches the specifications for your firearm Use of improperly reloaded ammunition can also be dangerous Firearms a
11. e AE Ea SLP 6 selector 2 4 AS we a Uf ti oN lao 7 pin y QUe Wee 8 weight T Senet SS 9 arm base spring i 10 selector arm base L L selector arm spring selector arm pin selector arm i i 0D Po Firing mechanism of Model 220 shotgun 3 inch chamber version GA 12 410 Model 220 barrel assembly receiver firing pin firing pin spring firing pin bushing left hammer right hammer firing pin buffer 20 Choke Tubes warne Never install or remove choke tubes while the firearm is loaded Only install or remove choke tubes with the firearm unloaded the action open and the trigger block safely engaged Screw in Chokes Symbols Markings This is an option not all Model 100 shotguns have this feature The end of the choke tubes are marked with slashes to identify the choke construction Full Improved Modified Modified Improved Cylinder Cl Cylinder WARNING MAKE SURE YOU FULLY TIGHTEN THE CHOKE TUBE Shooting with a loose choke tube can cause damage to your shotgun Additional Information On Screw Choke Tubes A Only tighten or loosen choke tubes with flat key wrench supplied with shotgun Note wrench and extra choke tube or tubes if supplied are under the cardboard in front of the shotgun receiver in the box B Never shoot the shotgun with a partially installed choke tube C Model 100 shotguns are available with fixed choke or screw choke barr
12. ecome lodged Firing a subsequent cartridge into the obstructed bore will damage the shotgun and may cause personal injury to the shooter and those nearby Use lubricants properly You are responsible for the proper care and maintenance of your firearm and ammunition PARTS AND SERVICE To Order Parts ALL PARTS ARE SUBJECT TO A 10 00 CHARGE FOR SHIPPING AND HANDLING Some parts are restricted and may only be installed by returning the shotgun to us When ordering parts please state the Model Gauge Serial Number and Finish Color For parts information call 321 639 1432 Service To obtain information about returning your shotgun for service or repairs call 321 639 1432 One Year Limited Warranty This shotgun is warranted to the original retail customer for one year from the date of retail purchase against defects in material and workmanship All parts and labor or replacement at our option are covered The wood stock is not covered by the one year warranty The warranty on the wood stock is 60 days and is limited to the original retail customer and extends 60 days from the date of retail purchase and covers only manufactured and material defects 17 PARTS AND SERVICE cont d One Year Limited Warranty Transportation to and from our repair facilities government fees damage caused by failure to perform normal maintenance sales outside the United States damage caused by use of high velocity high pressure reloaded or other no
13. els There are two types of screw chokes available lead shot choke tubes and steel shot choke tubes When installed steel shot choke tubes protrude approximately from the muzzle end of the barrel and the mating lip will be flush with the end of the barrel When installed lead shot choke tubes fit flush with or slightly below the muzzle end of the barrel If you have lead shot choke tubes and intend to shoot steel shot cartridges or slugs then you must use only the IC or Cylinder tubes DO NOT fire steel shot or slugs in Modified Improved Modified or Full lead shot choke tubes If you have steel shot choke tubes you may fire steel shot cartridges through any of those choke tubes DO NOT fire slugs in Modified Improved Modified or Full lead shot choke tubes or Steel shot choke tubes D Correctly installed choke tubes Lead shot choke tubes should fit flush or slightly below the muzzle end of the barrel Steel shot choke tubes will protrude out from the barrel about and the mating lip will be flush with barrel end E Before using the shotgun make sure that the choke tubes are installed correctly F Keep choke tubes lubricated and installed Never fire the gun without a choke tube installed Handle choke tubes carefully since the leading edge is very thin 21 Notes on Shot Material and Chokes 1 Shells using Bismuth or Tungsten Matrix shot are subject to the same barrel and choke tube limitations as lead shot Shells using
14. er and wherever you are involved with firearms in the field on the range or in your home Commit these Ten Commandments to your memory Q 1st COMMANDMENT Always Keep the Muzzle Pointed in a Safe Direction his is the most important gun safety rule A safe direction is one in which an accidental discharge will not cause injury to yourself or others Never allow your gun to point at anything you dont intend to shoot Be especially careful when you re loading or unloading Treat every gun as if it were loaded And make it a habit to know where the muzzle is pointed at all times even when your firearm is unloaded No one will be injured by an accidental discharge if you keep your firearm pointed in a safe direction It s as simple as that O 2nd COMMANDMENT Firearms Should be Unloaded When Not in Use and Secured from Unauthorized Use Load your firearm only when you are in the field or on the range and ready to shoot Unload your firearm as soon as you are finished shooting Never bring a loaded firearm into your camp home or vehicle Unloading means unloading both the chamber and the magazine Before handling a firearm or passing it on to someone else visually check the chamber receiver and magazine to make sure there is no ammunition anywhere in the firearm Never assume a firearm is unloaded and never take someones word for it look for yourself When you are finished shooting and have completely unloaded the firearm leave its act
15. er to the other trigger to fire the second shot Single trigger Model 210 shotguns have a single trigger which is used to fire each barrel Once the trigger is pulled to fire the first barrel release the trigger The second barrel is then ready to be fired by pulling the trigger again External Control Parts cont d The Barrel Selector for Model 210 single trigger shotguns only Once the shotgun is loaded you may manually set the shotgun to fire a specific barrel first by using the barrel selector The barrel selector is a button on the trigger See Picture 13 When the button is pushed fully to the right listen for an audible click the first pull of the trigger will fire the right barrel and the second pull of the trigger will fire the left barrel When the barrel selector button is pushed fully to the left again listen for an audible click the first pull of the trigger will fire the left barrel and the second pull of the trigger will fire the right barrel Picture 13 WARNING When selecting a barrel make sure the safety is on and the muzzle is pointed in a safe direction NEVER use the barrel selector when the safety is in the off or fire position Once you have used the barrel selector button to select the desired barrel remove your finger from inside the trigger guard until you are ready to fire Fore End The fore end is the wooden grip piece which attaches to the barrel assembly and locks the bar
16. for deformation and retry closing the action once more If the shells are the correct type and the chambers are not blocked and the shells are not deformed and the top lever does not move at least three quarters of the full travel distance to the center after closing then unload the gun follow Unloading Instructions and have a competent gunsmith look at the gun or return the gun to Remington S P See address in Parts amp Service Section for inspection Note The top lever may not move completely to the center on a new shotgun until the gun is broken in The lever must move at least three quarters of the full travel distance Try and move the top lever to the center position by pushing it do not force it Picture 22 Picture 23 Picture 24 12 Loading and Unloading Your Shotgun cont d TO UNLOAD 1 Break open the shotgun by use of the top lever and tip the barrels down See Picture 25 2 Remove the shell s from the chamber s by grabbing them by the rim of the shell s and pulling them from the chambers and store them in a safe place See Picture 26 3 Visually check the barrels to make sure that they are free from obstructions See Picture 27 Picture 25 Picture 26 Picture 27 Firing Your Shotgun WARNING NEVER LOAD A CARTRIDGE INTO THE CHAMBER UNTIL YOU ARE READY TO FIRE THE SHOTGUN WARNING Do not disengage the trigger block safety until the shotgun is pointed in a safe direction and you are
17. g the top lever you must 1 make sure the safety mechanism is in the on or safe position 2 keep your fingers away from the trigger s and outside of the trigger guard and 3 control the direction of the muzzle of the shotgun Trigger s WARNING Never pull the trigger s until you are actually ready to fire Keep your fingers off the trigger s and outside of the trigger guard until you are ready to pull the trigger and fire the shotgun When opening and closing the action and when engaging or disengaging the safety mechanism make sure your fingers are outside the trigger guard and away from the trigger s Side by side shotguns are available in either a double trigger configuration Model 220 or a single trigger configuration Model 210 See Picture 11 and See Picture 12 Double trigger Model 220 shotguns are patterned after classic side by side shotguns with two triggers The front trigger always fires the right barrel The back trigger always fires the left barrel Pulling either trigger with the safe ty in the off or fire position fires the shotgun Picture 11 Picture 12 WARNING Never fire a double trigger shotgun by using the two fingers because you may inadvertently pull both triggers at the same time resulting in a near simultaneous firing of both barrels Use your index finger to pull one of the triggers to fire the first shot After that shot is fired release the trigger and move your index fing
18. he barrels engaged into the receiver swing the barrels up into the locked position The top lever should move back to the center once the barrels are locked into position Note The top lever may not move completely to the center on a new shotgun until the gun is broken in The top lever must move at least three quarters of its full travel distance See Pictures 17 18 and 19 10 Instructions For Assembly Of Shotgun cont d Picture 17 Picture 18 Picture 19 4 Now that the barrels have been locked into the receiver you must reattach the fore end to the barrel Pull outward on the mechanical latch in the center of the fore end and place the fore end on the receiver With an upward swinging motion lock the fore end onto the barrels Do not force the fore end into its locked position on the barrels If the latch does not go to its final flat position it may be necessary to push it into place Never force the latch in the flat position See Picture 20 Picture 20 Loading and Unloading Your Shotgun WARNING Never load or fire the shotgun unless the barrels is locked into position on the receiver and the fore end is locked in to the receiver and barrels WARNING Make sure the shotgun is pointed in a safe direction and the trigger block safety is engaged at all times while loading and unloading NEVER allow your fingers or other objects to contact the trigger s while loading or unloading WARNING Do not disengage the
19. iew 1 barrel assembly 2 extractor spring 3 plunger 4 right extractor 5 left extractor 6 Screw 7 pin 8 sling swivel ring 9 screw 10 barrel sling swivel base 11 front sight 12forend 13 washer 14 spring 15 latch body 16 forend latch 17 pin 18 Screw 19 screw 20 Screw 21 lever pin 22 left lever 23 right lever 24 hinge 25 lever spring 26 Screw 2 receiver 28 cam 29 cam pin 30 sear pin 31 left sear 32 left hammer assembly 33 plug 34 plug screw 35 follower 36 left rod assembly 37 right rod assembly 38 cocking lever 39 cocking lever pin 40 screw 41 locking lever 42 right hammer assembly 43 hammer pin 44 right sear 45 pin for safety and thumb piece 46 thumb piece 47 locking bolt 48 connecting rod 49 locking bolt spring 50 cam stop 91 threaded connecting piece 52 locking bolt lever 53 bal 54 sear lifter lever spring 19 55 Safety 56 sear lifter lever 57 sear lifter 58 sear lifter spring 59 sear lifter level pin 60 pin 01 screw 62 trigger plate 63 Screw 64 trigger guard 65 trigger guard screw 66 right trigger 67 trigger spring 68 left trigger 69 pin 70 stock 1 Screw 72 washer 73 butt plate 74 woodscrew 7S woodscrew 6 stock sling swivel base 77 sear spring 78 wright 79 pin 80 safety spring 81 bushing Model 210 with Single Trigger Model 100 1 left sear SN E 2 right sear gt gt 3 trigger AY y E 5 selector plunger ye
20. ion open Whenever you are carrying a loaded firearm in the field you must unload it before crossing a fence climbing into a tree stand or blind or in any other situation where you may not be able to fully control the firearm Never pull or push a loaded firearm toward yourself or another person Store your firearms unloaded in a secure place where unauthorized persons cannot gain access to them Store firearms and ammunition separately If you use an external security device such as a cable lock or trigger lock you must still keep the firearm unloaded when locked Whether you utilize a locked gun safe or external lock ing device it is your responsibility to make sure that children and other unauthorized persons cannot gain access to your firearm and ammunition A sra COMMANDMENT Never Rely on Your Firearm s Safety Mechanism to Justify Careless Handling If your firearm is equipped with a manual safety mechanism do not rely on the safety as an excuse for improp er or careless handling of the firearm The safety mechanism is merely a supplement to your proper handling of the firearm The safety mechanism may be broken or altered Even if you think you have previously engaged the safety in the safe position it may have been inadvertently disengaged without your knowledge while being carried Never assume that the safety mechanism is engaged in the safe position Your assumption may be wrong or mistaken Treat your firearms safety mech
21. is Clear of Obstructions Before Shooting With your firearm completely unloaded open the action and make sure there are no obstructions or debris in the barrel Even a small obstruction such as snow or mud in the barrel can cause the barrel or receiver to burst when the next round is fired Use a cleaning rod to remove obstructions and residues from the barrel If the firing noise or recoil seems weak stop and completely unload your firearm to check for obstructions before firing another shot NEVER try to shoot out an obstruction by loading and firing another round of ammunition A oth commanoment Never Alter or Modify Your Firearm and Have it Cleaned and Serviced Regularly Your firearm has been carefully designed and manufactured to operate according to certain factory specifications NEVER alter or modify your firearm especially its trigger or safety mechanism in any way Such alterations or modifications can adversely affect the safe operation of your firearm endangering you and those around you As with any mechanical device the parts of a firearm are subject to wear or breakage To assure optimum safe ty and performance your firearm must be maintained and serviced on a regular basis Only a competent gun smith or a Remington Authorized Service Center should service or repair your firearm Proper cleaning and lubrication are also important to maintain the safe and proper functioning of your firearm Follow the cleaning and lubrication i
22. nd practice the Ten Commandments of Firearm Safety If you have any questions about the safe use of a Remington firearm write to us at Remington Arms Company Inc Consumer Service P O Box 700 Madison NC 27025 0700 or call us at 1 800 243 9700 4 Use the Security Lock Provided with your Shotgun This shotgun comes with a security lock to assist in protecting against unauthorized use See Picture 1 The shotgun must be unloaded when the security lock is in place on the shotgun WARNING Using the security lock cannot substitute for securing your firearm and ammunition in separate locked locations gt Picture 1 The security lock operates as follows 1 To open the Trigger Lock put the Key into the notches of the Trigger Lock Nut and un screw it counter clockwise See Pictures 2 and 3 Remove the Trigger Lock Screw Picture 2 Picture 3 2 lo install the Trigger Lock on an side by side break open shotgun put the Trigger Lock around the trigger guard See Picture 4 Picture 4 Use the Security Lock Provided with your Shotgun cont d 3 Screw the Trigger Lock Nut on the Trigger Lock Screw clockwise and tighten the nut with the key DO NOT TIGHTEN THE NUT TOO TIGHT OR YOU COULD DAMAGE THE LOCK SCREW See Picture 5 Picture 5 4 To remove the Trigger Lock unscrew the Trigger Lock nut with the key and detach the Trigger Lock Screw See Picture 6 Picture 6 ANY WARNING Always store the key to
23. nded target place your trigger finger on the trigger The shotgun will fire when you pull or squeeze the trigger with the requisite force See Picture 30 Picture 30 6 If you are using a Model 210 shotgun and intend to fire a second shot release the trigger and then pull ita second time The second round will then fire If you are using a Model 220 shotgun move your finger to the other trigger and pull it The second round will now fire 14 Firing Your Shotgun cont d wanume Once you have fired the shotgun immediately push the trigger block safety to the on or safe position Then follow the unloading instructions above while keeping the muzzle pointed in a safe direction Instructions For Disassembly Of The Shotgun 1 Make sure the shotgun is unloaded FOLLOW UNLOADING INSTRUCTIONS and pointed in a safe direction 2 Make sure the trigger block safety is engaged in the on or safe position See Picture 34 Picture 31 3 Remove the fore end from the barrel by pulling out the mechanical lever in the lower center of the fore end and removing the fore end in a downward outward swinging motion See Picture 32 Never force the fore end off the barrel and receiver 4 With the barrel and receiver supported with one hand push the top lever fully to the right and tip the barrels down until they disengage from the receiver Check the barrels for damage and obstructions after removal See Picture 3
24. nstandard ammunition or by any unauthorized repair modification misuse abuse or alteration of the shotgun is not covered by this Limited Warranty Implied Warranty ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTIES OF MERCHANT ABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL RETAIL PURCHASE SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU To the extent any provision of this warranty is prohibited by federal state or municipal law which cannot be pre empted it shall not be applicable This warranty gives you specific legal rights and you may also have other rights which may vary from state to state To obtain warranty service send your shotgun with proof of retail purchase freight prepaid to REMINGTON I S P c o USSG 402 Richard Road Rockledge FL 32955 NOTICE It is illegal to ship a firearm with ammunition in the firearm or in the same packaging Firearms and ammunition must be shipped separately For information about shipping ammunition call 321 639 1432 Your Owner s Manual Always keep this manual with your firearm Make sure you understand all the warnings operation instructions and safety procedures When you lend give or sell the firearm be sure this manual goes with it You can get a copy of this manual from Remington upon request 18 PARTS LIST Model 210 220 Exploded V
25. nstructions set forth in the owners manual for your firearm NEVER attempt to clean or lubricate a loaded firearm 10th COMMANDMENT Learn How Your Firearm Operates Not all firearms are alike Before you use any firearm for the first time you must become totally familiar with how that firearm operates When you receive a new firearm read and understand the owners manual before assembling the firearm for the first time If you acquire a used firearm request an owners manual and have the rifle inspected by a competent gunsmith to determine whether it is in good working order If you do not have an owners manual contact the manufacturer to obtain one If you are selling or trading your firearm to someone else be sure to transfer the owner s manual to the new owner LEAD EXPOSURE WARNING Discharging firearms in poorly ventilated areas cleaning firearms or handling ammunition may result in expo sure to lead a substance known to cause birth defects reproductive harm cancer and other serious physical injury Have adequate ventilation at all times Wash hands thoroughly after exposure SHOOT SOBER Guns and alcohol or drugs don t mix Never consume anything that would even mildly impair your judgement or physical coordination while handling a firearm WARNING Failure to follow any of these safety rules may cause personal injury or death to the shooter or bystander and damage to property Do not use a firearm until you fully understand a
26. re designed manufactured and proof tested to specified industry standards Hand loaded or reloaded ammunition that deviates either inten tionally or accidentally from specified loadings can be extremely hazardous Itis strongly recommended there fore that you use only factory ammunition from a reputable ammunition manufacturer If you do reload you have assumed the risks and responsibilities of an ammunition manufacturer A cin commanoment If Your Firearm Fails to Fire When You Pull the Trigger Handle With Care If a chambered round of ammunition does not fire when you pull the trigger stop and keep the muzzle pointed in a Safe direction Treat your firearm as if it could still discharge Keep your face away from the breech Slowly and carefully open the action return the safety mechanism to the safe position and unload the cartridge from the chamber Dispose of the cartridge safely If your firearm repeatedly fails to fire when you pull the trigger take your firearm and ammunition to a competent gunsmith or return the firearm to the manufacturer for inspection O 7th COMMANDMENT Always Wear Eye and Ear Protection Wear protective shooting glasses and hearing protection when shooting Be sure to wear eye protection when disassembling or cleaning a firearm to protect your eyes from springs and other tensioned parts Continued exposure to shooting noise can permanently damage your hearing Q 8th COMMANDMENT Be Sure the Barrel
27. ready to fire WARNING If a cartridge does not fire and the trigger has been pulled and the trigger block safety is disengaged Stop And do the following a Make sure the gun is pointed in a Safe direction b Engage the trigger block safety c Wait 60 seconds d Follow the instructions above for unloading the shotgun If during firing the sound of any cartridge is noticeably softer or louder than the previous cartridge fired Stop Do not load another cartridge or fire another cartridge and do the following a Make sure the gun is pointed in a safe direction b Engage the trigger block safety c Follow the instructions above for unloading the shotgun d With the shotgun unloaded visually inspect the shotgun for barrel blockage or damage Then inspect the mechanical operation and receiver of the shotgun for damage before continuing READ UNDERSTAND AND FOLLOW ALL WARNINGS AND INSTRUCTIONS IN THIS MANUAL BEFORE FIRING THE SHOTGUN 13 Firing Your Shotgun cont d TO FIRE THE SHOTGUN 1 Make sure the shotgun is pointed in a safe direction with the trigger block safety engaged See Picture 28 2 Make sure you are wearing eye and ear protection 3 Keep your fingers away from the trigger s Picture 28 4 Push the trigger block safety to the off or fire position with the red dot showing See Picture 29 Picture 29 5 With the butt stock held firmly against your shoulder and the barrels pointed towards your inte
28. rel assembly into the receiver See Picture 14 The fore end has a mechanical latch which is used to lock and unlock the fore end to the barrel assembly Never attempt to fire your shotgun without having the fore end locked in its proper position on the barrel assembly Picture 14 Instructions For Assembly Of Shotgun WARNING Before you begin to assemble the shotgun you MUST 1 look down the barrel from the breech end toward the muzzle end to make sure there is no ammunition in the chambers or obstruction in the barrels and 2 make sure the safety is in the safe position Your shotgun was shipped with the barrel assembly barrel and fore end detached from the receiver assembly To assemble the shotgun follow these instructions 1 Remove the plastic bags or wrapping covering the parts Then remove the fore end from the barrel by pulling outward on the mechanical lever in the lower mid section of the fore end and tipping the fore end out and away from the barrel See Picture 15 See Picture 15 Picture 15 2 Now push the top lever of the receiver to the right and hold with one hand Do not force the top lever See Picture 16 Ly Picture 16 3 Holding the barrels with the other hand engage the lower locking lug located on the lower portion of the barrel with the receiver The half round cut out on the lower locking lug fits around the round bar in the forward lower portion of the slot in the receiver With t
Download Pdf Manuals
Related Search