Operating instructions
Contents
1. NI a a A V N gt 21 22 23 24 25 26 27 28 29 30 31 Main switch Door opener Digital display Time delay Additional options Programme buttons Programme seguence indicator Salt refill indicator Rinse aid refill indicator pliance interior Upper basket with additional cup rack Additional cutlery basket for the top basket Top spray arm Bottom spray arm Dispenser for salt Filters Cutlery basket Bottom basket Lock for detergent dispenser Dispenser for rinse aid Detergent dispenser Rating plate some models Water softener In order to rinse dishes and glasses satisfactorily the dishwasher requires soft water i e containing little or no lime otherwise water stains will be left behind on crockery and glasses etc If the tap water exceeds a certain level of hardness it must be softened i e decalcified so that it can be used in the dishwasher This is achieved by adding a special salt to the water softener inside the dishwasher The water softener that is the required amount of salt is set up according to how hard the tap water is Setting up the water softener Determine the level of hardness of your tap water Your local water company or service agent can help you with this Identify setting from the fol2. Large sheets or grilles and plates which have a diameter greater than 30 cm gourmet plates pasta plates dinner plates can be cleaned with the aid of the spray head To do this remove the top basket and insert the spray head as illustrated in the diagram To ensure that the spray jet can reach all parts the baking sheets as illustrated max 4 baking sheets and 2 grilles Never operate the dishwasher without the top basket or baking sheet spray head some models Brief and handy everything your dishwasher needs Before using for the first time read the installation and operating instructions Fill with special salt Fill with rinse aid Fill with detergent Select programme E Adjusting the water softening system Read off the correct setting for your water hardness Request the water hardness value in your area from your Wasser H rte mmol l Einstellwert water supply company and ll Machine enter it here 0 6 70 13 18 12 14 9 10 UN 81052178 11 12 9 21 only before first use 13 16 lll 22 29 of the appliance or if 17 21 Ill 3 0 3 7 me rasi hardness 2230 38 54 3150 V 55 89 a Switch on appliance Press On Off switch running time of the chosen programme appears Swi
3. The LOW SALT indicator 8 on the front panel will light up initially but will extinguish again after a short period when the salt solution has become sufficiently concentrated When the control is set to it is not necessary to fill up with salt as none will be consumed while the dishwasher is operating The LOW SALT indicator is switched off If the control is set between and 1 then salt must be added to the dispenser AN Warning Do not pour detergent into the container for special salt This would destroy the water softener en Salt refill indicator As soon as the salt refill indicator 8 is lit on the control panel refill with salt immediately before the next rinse cycle Depending on the washing frequency and the hardness setting the regeneration salt may not have to be topped up for several months Adding rinse aid The rinse aid is required for stain free utensils and clear glasses Use only rinse aid for domestic dishwashers Open the cover on the rinse aid dispenser 29 To do this press the mark 1 on the cover and simultaneously lift the cover on the control plate 2 Carefully pour in the rinse aid to just below the edge of the filler opening Close the lid ensuring that you hear it snap closed To prevent excessive foam formation during the next rinse cycle remove any rinse
4. Built under and integrated appliances which are subsequently installed as free standing appliances must be secured to prevent them from falling over e g by screwing them to the wall or by installing them under a continuous worktop which is screwed to the adjoining units For Swiss version only The appliance can be installed without difficulty between wooden and plastic walls in a kitchen range If the appliance is not connected via a plug the installation side must feature an all pole disconnector with a contact gap of at least 3 mm in order to satisfy the relevant safety regulations 23 en Installation The dishwasher must be connected by a gualified technician to ensure correct operation The specifications for supply drainage and connected load must fulfil the required criteria as stated in the following paragraphs or in the installation instructions Install the appliance in the following sequence Check the delivery Install the appliance Connect the waste water Connect the fresh water Connect the power supply Delivery Your dishwasher was checked at the factory to ensure that it was in perfect working order This may have left some small water stains in the dishwasher These will disappear after the first rinse cycle Installation The required installation dimensions can be found in the installation instructions Using the height adjustable feet adjust the appliance u
5. Spray arms Remove blockages deposits e Pull lower arm upwards Unscrew upper arm Eliminating minor faults yourself Clean spray nozzles under flowing water perhaps with toothpick Self help pays Screw in filter system NOTE MARK Insert lower arm v o Screw in upper arm Cleaning the waste water pump With some models Ladle out water and remove filters Unscrew cover Torx T20 Check area of fan impeller for foreign objects Screw in cover and insert filters Fault Possible Cause Remedy Fault Possible Cause Remedy Residual water in the device Waste water pump blocked gt Clean waste water pump see above Dishes not clean Utensils are situated too close to each Spread out the utensils avoid contact other or on top of each other between the utensils Programme not yet ended gt Close and switch on appliance or Sand or grainy residues j A terminate programme see Terminating on dishes Too little cleaning product Follow manufacturer s specifications the programme detergent ME Unsuitable programme selected Select more intensive programme Spray nozzles blocked Clean spray arms see above Device bes SIOPS Supply fitting not open gt Open supply fitting Filters dirty not inst
6. Faes hos kundenservice hhv handelen meerprijs verkrijgbaar K dost n pres servisn sluzbu pop obchod In vendita presso il servizio assistenza clienti x o in commercio Aati etat TNV urmpeola TEXVIK G x c UMNPETNONS MEAATWV rj TO A vev szolg latn l ill a kereskedelemben lehet beszerezni TANHA FE MAKAA me Saatavissa houltopalvelusta tai alan liikkeiista Kan kgbes hos serviceafdeling eller forhandler
7. 2 after 1 minute i h li The programme will stop gt appliance Further advice be found in the instruction manual Loading the dishwasher correctly Arrange dishwasher proof utensils having removed any ash wax grease ink sticky labels remove large remnants of jam dairy products and food according to the operating instructions and check that the spray arms can rotate freely 9000 116 053 E 4 9000 116 053 gt Montageanweisung Instru es de montagem E instrukcja monta u Assembly Instructions Monteringsanvisning Mont n n vod Instructions de montage Montasjeveiledning Szerel si tmutat K Vontage Voorschriften Assennus ohjeet 7 gi c 2 Eg istruzioni peril montaggio Monteringsvejledning Ed 5 UJ ous EI O nyia ouvapuoyn Ir Montaj kilavuzu EI dE AE aft HH instrucciones de montaje If KL 9000 116 053 8702 630 634 I 81 Niro Haube nicht einklemmen j verspannen do not pinch brace ne pas coincer calar verticalement No doblar Ajustar 566 3 T20 SY e Torx To
8. 2in1 They contain detergent and rinse aid or salt function 3in1 They contain detergent rinse aid and salt function 4in1 They contain a detergent rinse aid salt function and an additional glass protection component In addition other combined products with a comparable effect are offered according to the manufacturer Always check the type of detergent or combined product which you are using Always follow the operating instructions or the information on the packaging The rinse programme is automatically adjusted in order to obtain the best possible rinsing and drying result Observe the following important information if using combined cleaning products Regeneration salt is not required up to a water hardness of 21 dH 37 fH 26 Clarke 3 7 mmol l only No other settings on the appliance are required Salt is still required if the water hardness is above 21 dH 37 fH 26 Clarke 3 7 mmol l Fill the salt dispenser with salt 24 and select setting 6 on the water softening system If in doubt please contact the detergent manufacturer especially if the utensils are very wet at the end of the programme limescale forms 13 en N Optimum rinsing and drying results can be obtained by using standard detergents in conjunction with separate application of salt and rinse aid Observance of the operating instructions or information on the pack
9. be installed in a high sided unit ensure that the unit is attached properly and also at the rear Built under and built in appliances should always be installed under a continuous work surface which is attached to the adjacent cupboards in order to ensure that the appliance is entirely stable After the appliance has been installed the mains plug should still be easily accessible Not on all models The plastic housing on the water input contains an electrically operated valve The connecting wires are inside the inlet hose Do not cut through this hose and do not immerse the plastic housing in water AN Warning For safety reasons if the appliance is not fitted in a recess thereby making a side wall accessible the door hinge area should be covered at the side Risk of injury Covers are available as optional accessories from customer services or specialist stores In daily use AN Warning Knives and other sharp pointed utensils must be placed with the points down in the cutlery basket or horizontally in the utensils basket Use the dishwasher only in the household and only for its designed purpose i e for washing domestic dishes Do not lean or sit on the open door The appliance could tip Please note that free standing appliances may tip over if the baskets are overloaded The water in the appliance is not drinking water Do not add any solvents to the washing cha
10. common occurrences and their remedies should help you identify the causes of most problems Problems A Attention Remember Repairs may be carried out by a technician only If a component has to be replaced ensure that only original spare parts are used Improper repairs or use of non original spare parts may cause considerable damage and put the user at considerable risk When the appliance is switched on The appliance does not start The mains fuse has tripped The appliance plug has not been inserted The appliance door has not been shut properly The tap has not been turned on The filter on the water supply hose is blocked Switch off the appliance and pull out the mains plug Turn off the tap Then clean the filter which is situated at the connection of the supply hose Finally restore the power turn on the tap and switch on the appliance With the appliance itself Lower spray arm rotates with difficulty Spray arm is blocked by small items or food remains Lid in detergent compartment cannot be closed Detergent compartment has been overfilled Mechanism is clogged with remnants of detergent Indicator lamps do not extinguish after washing has finished Indicator lamps do not extinguish after washing has finished Main switch is still set to ON Remnants of detergent stuck inside dispenser Compartment was damp when it w
11. models additional functions 5 can be set with the buttons Soaking The soaking cycle runs before the main programme and must be selected before the programme starts In this additional programme cooking utensils e g pans bowls etc can be soaked and prerinsed in the bottom basket It is recommended to put approx 5 g of detergent on the door G Saving time VarioSpeed The gt gt Save time lt lt function can reduce the running time by approx 20 to 50 depending on the selected rinse programme The particular change in the running time is indicated on the time remaining display To obtain optimum cleaning and drying results at a reduced running time water and energy consumption are increased Half load If you have only a few items to wash e g glasses cups plates you can switch to Half load The half load additional function saves water energy and time It is recommended to put a little less detergent in the detergent dispenser than for a full load 18 Maintenance and care A regular inspection and maintenance of your machine will help to prevent faults This saves time and prevents problems Overall condition of the machine Check washing chamber for grease and limescale deposits If you find such deposits Fill the detergent dispenser with detergent start the appliance without utensils in the programme which has the highest wash temperature Clean t
12. still closed press the lock 28 to open the detergent dispenser Adding detergent Fill the dispenser 30 with detergent Dosage see manufacturer s instructions on the detergent packaging E cs The cleaning tabs from various manufacturers exhibit differing dissolving properties so washing power may not develop fully during short programmes and there may be undissolved cleaning agent residue It is recommended to use washing powder for these programmes The Intensive programme on some models requires one tab only When using washing powder you can apply some of this cleaning agent to the inside of the appliance s door Reduce costs If your dishes are only moderately dirty you may be able to use less detergent than recommended Close the lid on the detergent compartment Press down the lid 1 until it clicks shut 2 f you are using detergent in tablet form read the manufacturer s recommendations on the packaging in order to determine where the tablets should be placed inside the dishwasher e g in cutlery basket detergent compartment etc Make sure that the lid on the detergent compartment is closed even if you are using tablets en auto 3in1 The use of so called combined detergent products may make the use of rinse aid and or salt unnecessary There are currently several types of combined detergent products available
13. 9000 256 144 8707 Operating instructions Dish washer IG 6507 K ppersbusch ALLERFEINSTE K CHENTECHNIK en Index Safety instructions 4 Getting to know your appliance 6 Water softener 6 Filling the salt dispenser 7 Adding rinse aid 8 Utensils 9 Detergent 12 auto3in1 13 Overview of programmes 15 Washing dishes Additional functions Maintenance an Fault finding dcare Customer Service Information Installation Waste disposal 16 18 18 20 23 23 24 25 en Safety instructions Delivery Immediately check the packaging and dishwasher for any damage which may have been caused in transit Do not use a damaged appliance but consult your supplier Please dispose of packaging material properly Installation Install and connect the appliance according to the installation and assembly instructions The dishwasher must NOT be connected to the power supply during installation Ensure that the protective conductor system of the domestic electricity supply has been installed correctly Electrical connection conditions must correspond with the specifications on the rating plate of the dishwasher f the dishwasher is to
14. aging of the combined detergents determines their effectiveness Even if the rinse aid and or salt refill indicator is lit the rinse programme runs correctly when 3in1 products are used If the rinse aid refill indicator 9 or salt refill 8 indicator is defective and you would like to switch it off proceed as follows Switching the rinse aid refill indicator off and on You can switch the rinse aid refill indicator 9 onor off This function can be changed as follows Close the door Hold down the programme button 4 and press the main switch 1 until the digital display lights up then release the buttons 3 is indicated on the digital display rinse aid refill indicator on By pressing the programme button 4 you can switch off ULU or switch on the rinse aid indicator Switch off the main switch 1 the setting is saved 14 Switching the salt refill indicator water softening system off and on Close the door Hold down the programme button B and switch on the main switch 1 then release the buttons The illuminated button B and the factory set value H O on the digital display flash To change the setting press the programme button B Each time the button is pressed the set value increases by one w
15. aid which has run over with a cloth Adjusting the amount of rinse aid The amount of rinse aid added to the water can be varied by adjusting the stepless control The rinse aid control has been set to 4 in the factory Do not alter the setting of the rinse aid control unless streaks turn knob towards or water marks turn knob towards are left on the dishes 29 Rinse aid controller Rinse aid refill indicator As soon as the rinse aid refill indicator lights up on the control panel 9 refill with rinse aid If using detergent products with integrated rinse aid the rinse aid refill indicator can be switched off see Switching the rinse aid refill indicator off and on in the auto 3in1 chapter en Utensils Not suitable Cutlery and utensils made of wood Fragile decorative glasses hand crafted and antique utensils These decorative items are not dishwasher proof Plastic parts sensitive to hot water Copper and tin utensils Utensils which are soiled with ash wax lubricating grease or ink Absorbent materials such as sponges and cloths Aluminium and silver parts have a tendency to discolour and fade during the wash cycle Even some types of glass e g crystal glass objects may turn cloudy after many wash cycles Recommendation In future buy utensils which are identified as d
16. alled securely Clean the strainers see above Supply hose kinked gt Bay Supply Without Rinks Spray arms blocked Arrange the utensils so that the spray Supply fitting jammed or calcified gt 1 Unscrew water connection arms can rotate freely 2 Clean filter in the water connection 3 Flow rate must be min 9 I min when the water inlet is open If the flow rate is less replace the Stains and streaks Rinse aid dosage too high too low Streaks Reduce dosage supply fitting Water or limescale stains Increase o dosage Milky residues on dishes Water softening system incorrectly set Set water softening system correctly can be removed no special salt Refill with special salt Too little cleaning product gt Follow manufacturer s specifications Plastic parts parts of Discolorati ibocan detergeni dishes discoloured aneen y ooo e i gt Discoloration is quite safe fades after Milky film glasses cloudy Glasses not dishwasher proof Use dishwasher proof glasses subsequent rinse cycles dull cannot be removed Use glass friendly cleaning products Cutlery rusty Cutlery not rust proof Use dishwasher proof cutlery Hard knife blades are more susceptible Extraneous rust gt Never wash rusting parts in the appliance Stopping the programme Press and hold the two reset buttons simultaneously for approximately 3 seconds while the programme is running RESET 0 00 appears
17. as filled up with detergent Compartment must be dry before detergent is added Refill display does not light up Rinse aid refill indicator switched off see auto 3in1 chapter Salt refill indicator switched off see auto 3in1 chapter en Water remains inside appliance after programme has ended Blockage or kink in drainage hose Pump is jammed Filters are blocked The programme is still running Wait for the programme to end numerical display will indicate 0 Perform Reset function during washing Unusual amount of foam is created Normal washing up liquid has been poured into the rinse aid container Remove any spilled rinse aid with a cloth as it could otherwise lead to excessive foaming during the next washing cycle Appliance stops suddenly while washing is taking place Cut in electricity supply to appliance Water supply has been interrupted Knocking sound can be heard while washing is taking place spray arm is knocking against the dishes inside the appliance Rattling sound can be heard while washing is taking place Crockery has not been stacked properly inside the appliance Knocking sound coming from inlet valves This is caused by the way the water pipes have been laid and it has no effect upon the way the appliance functions There is no remedy for this 21 en With the dishes cutlery etc 22 Remnan
18. d 23 and the arm mountings Inspect the nozzles in the spray arms for blocked holes due to remnants of food If necessary pull the lower arm 23 upwards and lift it off Unscrew the upper spray arm 22 Clean both spray arms under running water Refit the spray arms Ensure that the lower arm has locked into place and the upper one is screwed tight 19 en Pump on applicable models Larger remnants of food that have not been trapped by the filters and have been left in the water can cause a blockage in the pump The water is no longer pumped out of the dishwasher and it can be seen covering the filter Proceed as follows First always disconnect the appliance from the power supply Ladle out as much water as possible Remove the filters 25 Undo the screw in the cover Torx T 20 and remove the cover Inspect the inside and remove any obstructions that you find Re insert the cover and screw down Re insert the filters and screw down 20 Fault finding Resolving minor problems yourself Experience has shown that you can resolve most problems that arise during normal daily usage yourself without having to call out a service engineer Not only does this save costs but it also means that the appliance is available for use again that much sooner The following list of
19. d reset the programme Deactivating the button lock Hold down the button B for approx 4 sec until the display goes out At the end of the programme 2 22 on the digital display the button lock is cancelled If there is a power failure the button lock is retained Whenever a programme is restarted the button lock must be reactivated en Damage The appliance may be repaired and opened up by a technician only First disconnect the appliance from the power supply Pull out the mains plug do not tug the power cord or switch off the fuse Turn off the tap Disposal Make redundant appliances unusable to prevent subsequent accidents Dispose of the appliance in an environmentally friendly manner AN Warning Children could get locked in the appliance risk of suffocation or get stuck in other positions Therefore Remove the mains plug cut the mains wire and set aside Damage the door lock so that the door can no longer be closed You will need to purchase the following before using the dishwasher for the first time special salt for use in dishwashers detergent rinse aid Only use products which are suitable for dishwashers en Getting to know your appliance Diagrams of the control panel and the interior of the appliance can be found in the envelope at the front Individual positions are referred to in the text Control panel
20. he appliance with detergents appliance cleaners which are particularly suitable for use with dishwashers Regularly wipe the door seal with a damp cloth Never use a steam cleaner to clean your dishwasher The manufacturer is not liable for any consequential damage Regularly wipe the front of the appliance and panel with a damp cloth water and a little washing up liquid will suffice Do not use sponges with a rough surface or abrasive detergents as these could scratch the surfaces A Attention Never use other chlorinated household detergents Health hazard Salt and rinse aid Check the refill indicators 8 9 If required top up the salt and or rinse aid Filters The filters 25 prevent larger remnants of food or other objects from getting inside the pump This residue can occasionally clog up the filters The filter system consists of a filter cylinder a flat fine filter and depending on the model a microfilter Inspect the filters for obstructions every time the dishwasher has been used By unscrewing the filter cylinder you can remove the filter system Remove any food remnants and clean the filters under running water Reassembly Insert the filter system and screw down with the filter cylinder en p N Spray arms Lime and remnants of food in the washing water can block the nozzles in the spray arms 22 an
21. hen the value 1 is reached the display jumps back to the salt refill indicator water softening system has been switched off Switch off the main switch 1 The set value is stored within the device Approx 4 litres of water are required to regenerate the water softening system As a result the water consumption per rinse cycle increases by 0 to maximum 4 litres depending on the water hardness setting zi o If you use the detergent and rinse aid separately or switch from combined detergents to standard cleaning products ensure that the rinse aid refill indicator has been switched on and the water softening System has been set to the correct water hardness en Overview of programmes The max possible number of programmes is illustrated in this overview The corresponding programmes for your appliance can be found on the fascia Type of Dishes e g porcelain pans Non sensitive Mixed Delicate Mixed cutlery glasses etc Type of food remnants e g Soups souffl s Soups Coffee cake milk Rinse off if potatoes pastries potatoes sausage cold drinks the dishes rice eggs pastries salads have been fried food rice eggs stacked fried food for several days in the ET ET m dishwash du Large Little Very little er prior to food remnants
22. idual current operated circuit breaker which features the symbol Only this circuit breaker guarantees compliance with the currently valid regulations Removing the appliance It is essential when removing the appliance to observe the following sequence First disconnect the appliance from the power supply Pull out the mains plug Turn off the water supply Disconnect the waste water and fresh water connections Loosen the fastening screws under the worktop If fitted remove the base panel Pull out the appliance carefully pulling the hose behind Transporting the dishwasher Drain water from the dishwasher Secure all loose parts The appliance should only be transported in an upright position f the appliance is not kept upright during transport any water left inside may seep into the control module and cause subsequent errors with programme functions The appliance must be drained in the following sequence Turn on the tap Close the door Set main switch to ON Select the B programme The programme duration in minutes is shown in the numerical display Wait for approximately 4 minutes Terminate the programme by pressing _A and simultaneously The time display changes to 2 71 Wait a further minute and then Switch the appliance off Turn off the tap Protection from freezing temperatures If the appliance i
23. ime depending on the selected programme can vary greatly As the effect is not detected until a programme is running the time may be longer or shorter than expected Time delay You can delay the start of the programme in 1 hour steps up to 24 hours Switch on the appliance Press the timer programming button 4 until the digital display 3 jumps to ij f Keep pressing the timer programming button until the reguired time is displayed Todelete the timer programming keep pressing the button until 4 77 is displayed You can change your programme selection at any time until the programme starts End of programme The programme has ended when a figure 2 07 appears in the numerical display 3 Switching the dishwasher OFF Several minutes after the programme has ended Set the main switch 1 Turn the water tap off Does not apply when Aqua Stop unit has been fitted Remove dishes etc when they have cooled down At the end of the programme please open the door fully and not partially when emptying the dishwasher Any escaping water vapour could damage sensitive worktops to OFF Interrupting the programme Switch off the main switch 1 The lit display goes out The programme is saved If there is a warm water connection or if the machine has already heated up and the appliance door was opened leave the door ope
24. ishwasher proof Damage to glassware and other dishes Possible causes type of glass or manufacturing process chemical composition of detergent water temperature and duration of dishwasher programme Suggested remedy Use glassware or porcelain dishes that have been marked dishwasher proof by the manufacturer Use a mild detergent that is described as kind to dishes If necessary seek further information from detergent manufacturers Select a programme with as low a temperature and as short a duration as possible To prevent damage take glass and cutlery out of the dishwasher as soon as possible after the programme has ended en Loading the dishwasher Remove large food remnanis It is not necessary to rinse them off under running water When loading the dishwasher ensure that all utensils are secure and cannot fall over the openings of all receptacles are face down curved or indented utensils are at an incline allowing water to drain the two spray arms can rotate freely Very small items should not be washed in the dishwasher as they could easily fall out of the baskets Removing the dishes To prevent water dripping from the top basket onto the dishes in the lower basket we recommend that you empty the lower basket first and then the top basket Cups and glasses Upper basket 20 not included with all models Pots a
25. leaching effect Washing temperature was set too low Traces of rust on cutlery Cutlery is not sufficiently rustproof Salt content in washing water is too high Lid on salt container is screwed tight Too much salt was spilt while filling container Glasses become clouded and discoloured coating cannot be wiped off Unsuitable detergent was used Glasses are not dishwasher proof Smears left behind on glasses and cutlery glasses have acquired a metallic appearance Amount of rinse aid set too high Customer Service Please call your local service agent if you are not able to resolve any problem yourself The name of your nearest service agent is shown in the Customer Service address list When you call please provide details of the model number 1 and the production FD number 2 which are shown on the nameplate 31 on the appliance door 1 ro 2 ME AN Attention Please note that a visit by the customer Service technician in the event of a fault or one of the problems previously discussed is not free of charge even during the warranty period en Information Notes on comparison tests You will find details of the conditions for the comparison tests on the additional Notes on comparison tests sheet The consumption values for the relevant programmes are given in the introduction General
26. lowing water hardness table Water hardness table dH 0 6 0 11 0 8 0 1 1 RENE 7 8 12 15 9 10 1 2 1 4 REIR 9 10 16 17 11 12 1 5 1 8 gt 11 12 18 21 13 15 1 9 2 1 13 16 22 29 16 20 2 2 2 9 PE 17 21 30 37 21 26 3 0 3 7 gt 22 30 38 54 27 38 3 8 5 4 gt 81 50 55 89 39 62 5 5 8 9 gt fH Clarke mmol l Close the door Hold down programme button _B and press 1 main switch until the digital display illuminates then release the buttons The LED for button B flashes and the digital display displays the factory setting To change the setting press programme button B Each time the button is pressed the set value increases by 1 after H O 1 the setting goes back to H 77 Switch off the main switch 1 The chosen setting has now been stored en Filling the salt dispenser Salt must always be filled before the appliance is switched on so that excess salt solution is immediately flushed away to prevent corrosion Open the screw type cap of the compartment 24 Before using the appliance for the first time pour about 1 litre of water in the salt container Then refill with salt not cooking salt until the salt container is full max 1 5 kg When you refill the salt water is being displaced and drains off
27. mber Danger of explosion Open the door carefully when the programme is still running There is a risk of hot water spraying out of the appliance To prevent injuries e g caused by stumbling open the dishwasher only briefly in order to load and unload the dishwasher Read and observe the safety nformation and instructions for use on the packaging for cleaning and rinsing agents Children in the household f fitted use the childproof lock An exact description can be found in the back of the envelope Do not allow children to play with or operate the appliance Keep children away from detergents and rinse aid These may cause chemical burns in the mouth throat and eyes or asphyxiation Keep children away from an open dishwasher There could still be detergent residue inside f the appliance is installed at eye level ensure when opening and closing the door that children are not caught or crushed between the appliance door and the cupboard door situated below Childproof lock button lock You can secure your appliance from being unintentionally switched over e g improper operation by children Activating the button lock Select the required programme Hold down the button B for approx 4 sec until this L1 is indicated on the digital display If any button is pressed while the programme is running this F1 is indicated on the digital display It is not possible to en
28. n for several minutes and then close Otherwise expansion may cause the appliance door to spring open Switch on the main switch again en Terminating the programme Reset Simultaneously press programme buttons A and for approx sec The numerical display indicates 7 70 The programme sequence lasts approx 1 min Switch off the main switch 1 Changing the programme When the appliance is switched on the programme can be changed within minutes If the programme is changed subsequently programme sections e g Cleaning which have already started run to the end The new remaining time consists of the remaining time of the previous programme section and the remaining time of the newly selected programme Intensive drying In the final rinse the appliance operates at a higher temperature and therefore an improved drying result is obtained Caution if utensils are fragile Close the door Hold down programme button A and press main switch until 1 the digital display illuminates Release both buttons The LED for button A flashes and the digital display 3 displays the factory setting 5 00 off or 5 7 on To change the setting press programme button A Switch off the main switch 1 17 en Additional functions on some
29. nd pans Lower basket 27 Cutlery Cutlery should be placed in the dishwasher always unsorted and with the eating surface pointing downwards The spray jet is then better able to reach the individual parts To prevent injuries place long pointed accessories and knives on the tag re some models or on the knife shelf available as an accessory Folding spikes on applicable models To improve stacking of pots and pans the Shelf noton all models Lean tall glasses and those with long stems against the shelf not against other items to be washed iti N Long items serving cutlery salad servers or knives should be placed on the shelf so that they do not obstruct the rotation of the spray arms The shelf can be folded back when not required for use Small accessories holder some models Light weight plastic accessories e g cups lids etc can be held securely in the small accessories holder en Adjusting the height of the basket some models If required the height of the upper utensils basket can be adjusted to provide more space for tall utensils either in the upper or lower basket Appliance height in cm 81 86 Select one of the two following procedures according to the design of the top basket for your appliance model Top basket with upper and lower roller pairs Pull ou
30. ng cartons and plastic film Corrugated cardboard consists mainly of wastepaper The moulded polystyrene parts do not contain any chlorofluorohydrocarbons The polyethylene film PE consists partly of secondary raw materials The wooden frames if fitted are made of untreated residual wood The hoops if fitted consist of polypropylene PP Disposal of redundant appliances Make redundant appliances unusable to prevent subsequent accidents Dispose of the appliance in an environmentally friendly manner 26 AN Warning Children could become locked in the appliance risk of suffocation or find themselves in other dangerous situations Therefore Pull out the mains plug sever and dispose of the power cord Destroy the door lock so that the door can no longer be closed This appliance is labelled in accordance with European Directive 2002 96 EG concerning used electrical and electronic appliances waste electrical and electronic equipment WEEE The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU Child proof lock 40 Switch on the child proof lock When the door is open the child proof lock 41 Open the door with child proof lock offers no protection switched on 42 Switch off the child proof lock Baking sheet spray head pe
31. ntil it is level Ensure that the appliance is standing firmly Waste water connection See the installation instructions for the required connection steps If required attach a siphon with drainage spigot Using the enclosed parts connect the waste water hose to the drainage spigot of the siphon Ensure that the drainage hose is not kinked crushed or twisted ensure that there is no sealing cover which prevents the waster water from flowing away 24 Fresh water connection Using the enclosed parts connect the fresh water connection to the tap according to the installation instructions Ensure that the fresh water connection is not kinked crushed or twisted When replacing the appliance always connect a new water supply hose to the water supply The old supply hose must not be re used Water pressure Minimum 0 05 MPa 0 5 bar maximum 1 MPa 10 bar If the water pressure is higher install a pressure reducing valve Flow rate Minimum of 10 litres per minute Water temperature We recommend that you use cold water If you do use hot water the temperature should not exceed 60 C Electrical connection Connect the appliance only to 230 V alternating current via a correctly installed Socket with protective conductor See rating plate for required fusing 31 The socket must be attached near the dishwasher and be freely accessible The connection may be modified by an electrician only Use only a res
32. pecific to the appliance e g temperature amount of water etc The water consumption values refer to a set water hardness value of 4 Aqua sensor some models The Aquasensor is an optical measuring device light barrier which measures the turbidity of the rinsing water The Aqua sensor is used according to the programme When the Aqua sensor is active clean rinsing water may be transferred into the next rinsing bath and or the temperature adjusted 16 If the turbidity is greater the water is drained and is replaced with fresh water In this way water consumption can be reduced by approx 4 litres Switching the dishwasher ON Turn on the tap Set main switch 1 to ON Indicators light up according to the last programme that was selected This same programme will run again if no other programme button 6 is pressed The numerical display 3 shows the expected duration of the programme The programme starts automatically Programme sequence indicator 7 Your dishes are being cleaned Your dishes are being rinsed i Your dishes are being dried Remaining running time display When the appliance has started the expected programme running time is displayed The programmed running time is affected by the water temperature the number of dishes as well as the degree of soiling If these conditions are changed the running t
33. rview Intensive Auto Eco Gentle Quick Prerinse 70 55 65 50 40 45 nn This overview shows the maximum number of programmes VC LE nn available You ll find the corresponding programmes of your uu ag I gt gt DA device on your control panel Duration hs mins 2 15 1 25 2 20 2 20 18382 0 30 0 19 The programme data are laboratory read Energy Consumption kWh 1 60 1 05 1 60 1 05 0 80 0 70 0 05 our accorgo te Water Consumption litres 16 10 17 12 14 10 4 European Standard EN 50242 In practice deviations are possible With Aquasensor 13 11 141 kk n Additional programmes Increased flexibility Soak Half load Time selection 5 Time reduction time saving Shortens the cleaning time reduces the drying m crockery in the lower basket programme starts automatically remember to add an extra 5g of cleaning agent when the door unlocks LY Saving time VarioSpeed JA gt s obtained by increased energy consumption at aconstant cleaning and drying performance for a few items saves water energy and time h some models Switches on as soon as you press the time selection button Alters the programme start in hourly steps Maintenance and care For perfect rinsing results Strainers Check if required clean Rotate filter cylinder remove filter system rinse under flowing water Insert
34. rx T 20 Torx T 20 Scheibe entfernen T remove disc g AO enlever le disque N 7 x gt Dichtheit nach einem Sp lgang pr fen B c Check for leaks after one wash cycle Tox T20 Eliminar disco E 3 4 1 2 V rifiez l tanch it apr s un lavage ags gt eg Verificar la estanqueidad tras un ciclo de lavado E 5 E max 60 C Se puede adquirir a trav s del Servicio de Asistencia T cnica o en el comercio especializado Pode ser adquirido nos Servicos T cnicos ou no com rcio da especialidade Yetkili servis veya sat yerleri ce af WEN zd PIER zerinden tedarik edilebilir pal 23 pie detis d pah 5 4 RI Dal Do nabycia w punkcie serwisowym lub sieci handlowej ber Kundendienst bzw Handel erh ltlich Available from your service agent or retailer Ve 502 7j Fourni par le SAV ou les revendeurs i Bij de Servicedienst resp in de handel tegen Erh lles via Service respektive handeln i 2m Lr mt 0 m s B gi r JE ef EN _ epee 12 12
35. s installed in a location where there is a risk of freezing temperatures e g in a holiday home all water must be completely drained out of the interior see Transporting the dishwasher Turn OFF the tap disconnect the supply hose and allow to drain en Waste disposal Disposal Old appliances are not worthless rubbish Valuable raw materials can be reclaimed by recycling old appliances Pull out the mains plug of the redundant appliance Cut off the power cord and discard with mains plug To prevent children from locking themselves in the appliance and suffocating destroy the door lock and childproof lock if fitted You received your new appliance in a protective shipping carton All packaging materials are environmentally friendly and recyclable Please contribute to a better environment by disposing of packaging materials in an environmentally friendly manner All plastic parts of the appliance are identified by internationally standardised symbols e g gt PS lt polystyrene When the appliance is being disposed of the plastic waste can be sorted for environmentally friendly recycling Please ask your dealer or inquire at your local authority about current means of disposal 25 en Disposal of the packaging Please dispose of the packaging material in an environmentally friendly manner Keep children away from shipping carton and packaging components Danger of suffocation from foldi
36. t the top basket Remove the top basket and re attach it to the upper or lower rollers en Top basket with side levers Rackmatic Pull out the top basket Tolower the basket press in one lever and then the other situated on the left and right of the basket exterior holding the basket firmly on the sides of the upper edge to prevent it from falling down To raise the basket hold the basket on the sides of the upper edge and lift it up Before re inserting the basket again ensure that it is at the same height on both sides Otherwise the appliance door cannot be closed and the upper spray arm will not be connected to the water circuit 12 Detergent You can use commercially available liquid or powder proprietary detergents for dishwashers or TABS do not use handwash If phosphate free detergents are used with hard tap water white deposits may be deposited more easily on utensils and the container walls This can be remedied by adding more detergent See detergent packaging to determine whether a detergent is suitable for silver parts If you have any other questions we recommend that you contact the helplines of the detergent manufacturers Detergent dispenser with dosing aid The graduated detergent dispenser helps you pour in the correct amount Lower line 15 ml Middle line 25 ml Full to the brim 40 ml If the detergent dispenser 30 is
37. tch off the appliance Everything ox When the display shows 0 00 end of programme press On Off switch 9000 155 371 8601 A Summary of instructions for dishwasher 8 0000000 Reset Quickly sorted How to adjust the water softening system Hold down programme button B and press main switch until the digital display illuminates then release the buttons The LED for button B flashes and the digital display displays the factory setting H 04 Each time button B is pressed the setting increases by 1 after H 07 the setting goes back to H 00 Switch off the main switch The chosen setting has now been stored Unscrew Only before using Pour in max Screw on the the lid the dishwasher 1 5 kg 3 Ib 5 oz lid Switch on for the first time salt never deter dishwasher pour approx 11 gent immediately 2 pt water into the salt opening Everything is sparkling clean Press mark 1 Pour in Close the lift up lid 2 rinse aid lid CLICK wey 1 Very dirty dishes a lot of detergent 40ml If required open Warning me mil Pour in Push the lid the lid press the g detergent f shut press pin combination 15 ml g PLOP products are not LS suitable for all programmes follow manufac turer s instructions Quick economical or intensive Programme Ove
38. ts of food are stuck to the dishes cutlery etc Dishwasher was not loaded properly Jets of water could not reach all parts of the dishes etc Too many items in the rack in the rack were touching each other Not enough detergent was added to dispenser Selected wash programme was not intensive enough Rotation of spray arm was obstructed by dish etc Nozzles in spray arm are blocked by remnants of food Filters are blocked Filters have been incorrectly fitted Waste water pump is jammed Plastic items are discoloured Not enough detergent was added to dispenser White stains are left on crockery glasses have a milky appearance Not enough detergent was added to input compartment Amount of rinse aid was set too low Although water is quite hard no salt has been put in appliance Water softener was set too low Lid on salt container is not screwed tight If you used a phosphate free detergent try a detergent containing phosphates and compare results Dishes cutlery etc have not been dried Selected programme did not include drying function Amount of rinse aid was set too low Items were removed from dishwasher too soon Glasses have a dull appearance Amount of rinse aid was set too low Tea stains or traces of lipstick have not been completely removed Detergent does not have a sufficient b
39. washing State of food V E 7 ery d ii Medium Lightly Adhesive E E E E E E hio LM Intensive Auto Eco Gentle Quick Prerinse preg 70 55 70 50 40 45 HT ju Prerinse Prerinse Prerinse Prerinse seguence 40 2 ii 965 Clean Clean Clean 285 50 40 45 Clean 9 Go 70 295 Inter Inter Inter o E 9 0 mediate mediate mediate 255 2 rinse rinse rinse Elo SE S 3 Clean Clean Clean Inter Sos 99 id mediate 28 9 rinse FeO 52 o Clean 70 Dry Dry en Programme selection The most appropriate programme can be identified by comparing the type of crockery cutlery etc as well as the amount and condition of food remains with the details contained in the programme overview You will find the appropriate programme information in the introduction Washing dishes 22 Reduce costs If only a small number of dishes have been loaded into the dishwasher selecting a programme that operates at the next lowest temperature will usually suffice Programme specifications The programme specifications can be found in the summary of instructions Programme specifications refer to normal conditions Greater deviations may occur due to varying amounts of dishes water supply temperature water pipe pressure ambient temperature mains voltage tolerances and the tolerances s
Download Pdf Manuals
Related Search