hawos Oktagon Operating instructions
Contents
1. Operating instructions hawos Oktagon i a Congrat ctl QLIONS k a E on pUrchasi ng your Aawos Hour null pm gt gt gt gt BBR D ATTENTION Safety is paramount Only connect your mill to a properly installed socket with earthing contact Do not use defective units If the mains cord is damaged only the manufacturer its customer service department or a qualified professional may replace it Only authorised hawos professionals may perform repairs Never operate your mill unattended Never reach into the funnel or flour outlet when the unit is operating risk of injury Before opening the housing be absolutely sure to pull the mains plug to prevent the unit from accidentally activating risk of injury Fe top Fixed grindstone Milling chamber bottom Rotating Safety is paramount A This device is not intended for use by persons including children with impaired physical sensory or mental abilities or who lack experience and or knowledge unless they are supervised by a person responsible for their safety or have been instructed by such a person in how to use the device Children must be under supervision to ensure that they do not play with the device A Never immerse the device in water hawos flour mills are equipped with an overcur rent circuit breaker that protects the motor from excessive current consumption e g if debris jams the grindstones Funnel2. wise Figure 7 The black marks must be located over one another Figure 8 When screwing the grindstone back into place make sure that it does not tilt Figure 9 Make sure the foam rubber gasket is properly seated arrow Return the funnel to its previous position and secure it with the brass screws Opening the grinder A Attention Turn off the mill with the On Off switch and then disconnect the mains plug before opening the housing to prevent the device from accidentally turning on risk of injury e Remove the two brass screws on the left and right side page 4 figure 1 e Lift off the funnel page 4 figure 2 e Firmly turn the top grindstone up against the plastic ring counterclockwise until you are able to remove it figure 6 In order to reassemble the mill position the mill so that the flour outlet is pointing towards you e Place the top grindstone on the inner plastic ring such that it is completely level e The black mark must be at 6 o clock over the retainer figure 7 e Push the stone down gently from above and screw it back until it locks into place one complete revolution and then to approximately 10 o clock See Figure 8 for this Make sure the foam rubber ring is properly seated You can now return the funnel to its previous position and secure it with the two brass screws figure 9 Technische Daten Model Oktagon 1 Oktago
3. Adjusting lever Brass screws grindstone Flour outlet On Off switch Before first use L Dear mill owner Weare delighted that you have decided on a hawos flour mill Your hawos will serve you well in preparing your natural food cuisine for many years to come Please observe the following notes before using it for the first time Please carefully read through these operating instructions to familiarise yourself with your hawos It will reward you with reliability and convenience Proper use The mill is conceived and designed for private household use The device is intended for grinding the mill feed listed on page 5 Product contents Mill funnel lid Brief instructions e Connect to a properly installed socket with a protective earthing contact e Place the flour bowl under the flour outlet e Set the fineness with the lever e Fill the funnel with the desired grain e Turn the device on adjust the fineness as needed e Turn off the device once you have finished grinding e Only use the flour mill for grinding food A table of edible mill feed is provided on page 5 Before first use Before you use the device for the first time please first carefully read through the safety instructions and operating instructions Only in this way will you be able to use all functions safely and reliably Hold onto these operating instructions for future reference Pass these operating instructions on to any subs
4. coarse with the motor turned on until the milling process starts again e Slowly set the lever back to fine page 4 figure 5 The mill is on but no flour is emitted If the grain is too wet or e g if spelt and oats are ground too finely the grindstones may be smeared Solution e Mill approximately 100 g brown rice semi coarse setting e f necessary open the grinder and remove any leftovers see the section Opening the grinder for this The mill turns off while in use Debris or clogged grindstones may cause the mill come to a standstill In such a case the overcurrent circuit breaker automatically deactivates the mill after approximately 20 seconds Solution e Remove any debris and or after the mill has cooled off mill approximately 100 g brown rice semi coarse setting The adjusting lever cannot be pushed to the fine setting If an overfilled flour bowl causes e g the flour to back up this may jam the grinder There is leftover grain or debris in the grinder Solution e When the mill is running change to the coarse setting and allow the grinder to run without any mill feed e f necessary open the grinder and remove any leftover flour and or debris If the grindstones are heavily laden clean them with a dry hard brush for this see the section Opening the grinder Opening the grinder Figure 6 Unscrew the top stone by turning it counterclock
5. able e g dry spices Proceed with care when trying new types and let us know about your results We are always delighted to learn more Oilseeds jam the grinder due to their high fat content For this reason mix mill feed with high fat content 1 1 with wheat or another grain 6 Cleaning Faults Cleaning A brush is integrated in the bottom rotating grindstone of your hawos which sweeps out the flour with every rotation thereby automatically cleaning the mill If you don t intend to use your mill for a prolonged period of time we recommend cleaning any leftover flour out of the grinder This is very easy with a vacuum cleaner Set the adjusting lever to coarse and then after having turned off the mill insert the vacuum cleaner nozzle into its funnel and flour outlet Do not in any case clean the housing with abrasive cleaners Never immerse the unit in water If necessary clean the housing with a damp cloth and then rub in a small amount of vegetable oil to preserve the surface Faults In the unlikely event of a fault you can rectify it easily The motor doesn t start Is the mill connected to a power supply Has the plug been properly connected with a socket Solution e Check both points and rectify the fault The motor hums but doesn t start running When turning off the unit grain may have clogged between the grindstones and may have jammed them Solution e Set the adjusting lever to
6. equent user of the product 1 Removing the transport guard see page 4 Start up 2 Mill feed Please only use clean and dry grains You can determine this if the seed crackles distinctly when you crush it against a hard surface with a spoon Wet grain can be crushed and then looks like an oat flake Please consult the table of mill feed on page 5 when adjusting the fineness Please only mill sweet corn for grinding corn Only process mill feed with the device once 3 Power supply Only connect the mill to an alternating current source Check whether the existing mains voltage corresponds to the voltage specified on the base plate 4 Location The mill housing is made of wood Wood is a living material that is affected by changes in temperature and humidity which may cause it to crack You can best protect and care for the housing by not placing the mill close to radiators and not placing it right next to a stove steam moisture 5 Setting up the mill A During use place the flour mill on a hard level base kitchen countertop The slots on the bottom of the device may not be obstructed so that the motor can be ventilated Start up Please first read through the section Before first use P 3 and the safety notes P 2 aoe Be absolutely sure to remove the e transport guard before first use You can remove the transport guard by removing the two brass screws figure 1 on the housing and liftin
7. g off the funnel figure 2 Completely remove the three red screws with a cross slotted screw driver figure 3 Check that the foam rubber gasket is properly seated around the hole in the top grindstone figure 4 You can now return the funnel to its previous position and secure it with the brass screws Milling Once connected to a power supply your hawos mill is ready for use Place a bowl under the flour outlet and adjust the fineness figure 5 Then fill the funnel with grain and turn on the mill Figure 1 Unscrew the two brass screws on the left and right Figure 2 Lift off the funnel Figure 3 Remove the 3 transport screws marked in red Figure 4 Make sure the foam rubber gasket is properly seated arrow Return the funnel to its previous position and secure it with the brass screws Figure 5 Set the fineness fine to the left coarse to the right Start up 5 Adjusting the fineness You can set the fineness of the mill feed steplessly between 1 and 9 using the adjusting lever When changing the setting from 9 to 1 the mill should either be on or the grinder must be empty The different types of grain and other mill feed differ considerably with respect to their fat and fibre content endosperms etc Our mill feed table is based on this hawos mills have undergone extensive testing and this table was compiled according
8. ly for your reference However the values provided are approximate and are dependant on the moisture content of the grain If you wish to increase the fineness above the level specified in the table the end result will be super Mill feed table Mill feed Setting from level Wheat 1 Rye 1 5 2 Spelt 1 5 2 Barley 25 Oats 2 5 Millet 1 Sweet corn 0 Durum wheat 0 Rice not parboiled rice 1 Buckwheat 1 Green spelt 1 Flax seed mix 1 1 with wheat 2 Chick peas 1 5 Green peas 1 5 Nutritional yeast flakes 15 Quinoa 0 5 Amaranth slowly pour into the funnel 0 fine This increases the risk of the grindstones clogging Pay attention to the milling noise If it diminishes considerably then the grindstones are starting to clog Set the adjusting lever to coarser Turn off the mill once all mill feed has been processed If there is no mill feed in the grinder you can hear the grindstones rubbing against one another in the fine setting Cause Despite a high degree of precision the threading for the fine setting always has to have a small amount of play This small amount of play is neutralised when the pressure from milling is exerted on the two grindstones Grains that by nature have their own unique hardness exert a different milling pressure on the grinder For this reason we recommend different settings Feel free to also try foods that can be rolled and those that can be poured that are not indicated on the adjacent t
9. n 2 Housing Funnel fill volume 1 100 g wheat Base area mm 200 200 Height mm 410 450 Grinding capacity for wheat approximately 125 g min approximately 220 g min Mill Corundum ceramic grindstone horizontally positioned 100 mm Weight 8 8 kg 10 3 kg Motor output 360 watts 230 volts 50 Hz 600 watts 230 volts 50 Hz Warranty 10 years The mill is conceived and designed for private household use The device is intended for grinding the mill feed listed on page 5 Any other use is deemed improper hawos assumes no liability for cases of improper use AN At the end of its lifecycle this product must be turned in at a collection point for recycling electric and electronic appliances The materials can be reused as labelled Please contact your community or city administration for the respective collection point _ hawos Service E If you have questions about your mill please give us a call or write us an e mail our customer service team is happy to assist you Tel 49 0 6172 671749 e E mail info hawos de Strong Mills Fine Flour hawos Kornmthlen GmbH Ober Eschbacher StraBe 37 D 61352 Bad Homburg v d H Germany Tel 49 0 6172 40120 0 Fax 49 0 6172 40120 19 hawos info hawos de www hawos de _GB gon__10 12 2009 GA_Okta
Download Pdf Manuals
Related Search